Wet-chemical synthesis of magnesium niobate nanoparticles powders

Nanosized and highly reactive magnesium mobate (MgNb2O6) powders were successfully synthesized by a new wet-chemical method by means of the dissolution of Nb2O5 center dot 5H(2)O and in a solution of oxalic acid followed by the addition of stoichiometric amounts of magnesium carbonate. The Nb-Mg-oxalic acid solution was evaporated resulting in a dry and amorphous powder that was calcined in the temperature range from 200 to 900 degrees C for 2 h. The crystallization process from the amorphous state to the crystalline MgNb2O6 was followed by thermal analysis. The calcined powders characterized by FT-Raman spectroscopy, X-ray diffraction (XRD) and their morphology examined by high resolution scanning electron microscopy (HR-SEM). Pure MgNb2O6, free from the second phases and obtained at 800 degrees C was confirmed by a combined analysis using XRD and FT-Raman. The average diameter of the particles was calculated from the HR-SEM image as 70 urn approximately. This technique allows a better mixing of the constituent elements and thus a better reactivity of the mixture to obtain pre-reaction products with high purity at lower temperatures and reducing cost. It can offer a great advantage in the PMN-PT formation with respect to the solid-state synthesis. (c) 2006 Elsevier Ltd and Techna Group S.r.l. All rights reserved.

Determination of low-aliphatic aldehydes indoors by micellar electrokinetic chromatography using sample dissolution manipulation for signal enhancement

This work describes a novel approach for the analysis of selected aldehydes (formaldehyde, acetaldehyde, propionaldehyde, and acrolein) and acetone in environmental samples using micellar electrokinetic chromatography (MEKC). The method is based on the reaction of carbonyl compounds with 3-methyl-2-benzothiazoline hydrazone (MBTH) that gives an azine intermediate with maximum absorbance at 216 nm. A systematic evaluation of sample dissolution medium was conducted as a means to enhancing sensitivity. In the best condition, samples were dissolved in 0.030 mol.L-1 tetraborate solution. This condition presented enhancement factors in the range of 35-54 for the aldehydes under investigation, computed as the improvement of the concentration limits of detection (LODs) with reference to the sample dissolved in pure water. The running buffer was 0.020 mol.L-1 tetraborate, pH 9.3, containing 0.050 mol-L-1 sodium dodecyly sulfate (SIDS). The overall methodology presented several advantages over established methods for aldehydes. Worthy mentioning that MBTH is available in high purity degree, dispensing laborious reagent purification procedures. A few method validation parameters were determined revealing good migration time repeatability (< 2.5% coefficient of variation, CV) and area repeatability (< 4% CV), excellent linearity (20-120 mug/L, r > 0.995) and adequate sensitivity for environmental applications. The LODs with respect to each single aldehyde were in the range of 0.54-4.0 mug.L-1 and 11 mug.L-1 for acetone. The methodology was applied to the determination of aldehydes indoors. Samples were collected in an impinger flask containing 0.05% MBTH solution, at a flow rate of 0.80 L.min(-1), during 2.5 h, at different times during the day. The most abundant carbonyls in the samples were acetone, followed by formaldehyde and acetaldehyde, with estimate peak concentrations of 452, 5.2 and 2.2 ppbv, respectively.

New glasses in the system InF3-BaF2-ErPO4

New glasses have been obtained in the system InF3-BaF2-ErPO4. Glass compositions with up to 30% mol Er3+ were shown to exist and characterized by thermal analysis, x-ray: diffraction, IR absorption and electronic spectroscopy. The systems with high Er3+ content were studied recording IR and visible emission spectral characteristics. A specially elaborated technique allowed the preparation of a high purity phosphate precursor ErPO4. X-ray identification of the crystalline phases appearing during thermal treatment have been carried out and parameters of a mixed fluoride Ba4In3-nErnF17 calculated.

Microstructured chalcogenide optical fibers from As2S3 glass: towards new IR broadband sources

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Influence of the heat treatment in the electrochemical corrosion of Al-Zn-Mg alloys

The localized corrosion of Al-(5.03%)Zn-(1.67%)Mg-(0.23%)Cu alloys and high purity Al has been studied using electrochemical techniques, optical microscopy, SEM and EDX. The samples were previously submitted to different heat treatments in which coherent and incoherent MgZn 2 precipitates with different distribution and aggregation degree were produced. The influence of NaCl and Na 2SO 4, dissolved oxygen, immersion time and convection were studied. In NaCl solutions, pitting potentials for the alloys were more negative than for aluminium, indicating an increase in their susceptibility to localized corrosion. Moreover, annealed and cold-rolled alloys presented more negative pitting and repassivation potentials than those submitted to age hardening with direct or interrupted quenching. In annealed and cold-rolled samples, pit nucleation and propagation takes place in the zones where MgZn 2 is accumulated. In the case of the age-hardened alloys, a double pitting behaviour is observed, the first one in the magnesium and zinc enriched regions and the second in the matrix. While the cold water quenched alloy is susceptible to stress corrosion craking, the alloy submitted to the interrupted quenching process is less susceptible to intergranular attack. The sulphate ion shifts the pitting potential of aluminium and the alloys by chloride towards more positive values because it impedes local accumulations of the latter. © 1992 Chapman & Hall.

Effect of atmosphere on the sintering and grain growth of tin oxide

High purity SnO 2 powder (>99.9%) was compacted in cylindrical pellets and sintered in atmospheres of dry argon, argon with water vapor, oxygen and CO 2 using 10 °C/min up to 1200 °C or isotherms in the range of 1000 to 1200 °C. Time, temperature and sintering atmosphere have large influence on grain growth and low influence on densification of this oxide. Surface diffusion is the dominant mechanism up to 1200 °C and evaporation-condensation is dominant above 1200 °C. The maximum linear shrinkage observed was about 2.0% and attributed to structural rearrangement of particles due to high capillary stresses developed with neighboring particles. © 1999 Trans Tech Publications.

Myotoxic phospholipases A2 isolated from Bothrops brazili snake venom and synthetic peptides derived from their C-terminal region: Cytotoxic effect on microorganism and tumor cells

This paper reports the purification and biochemical/pharmacological characterization of two myotoxic phospholipases A2 (PLA2s) from Bothrops brazili venom, a native snake from Brazil. Both myotoxins (MTX-I and II) were purified by a single chromatographic step on a CM-Sepharose ion-exchange column up to a high purity level, showing Mr ∼ 14,000 for the monomer and 28,000 Da for the dimer. The N-terminal and internal peptide amino acid sequences showed similarity with other myotoxic PLA2s from snake venoms, MTX-I belonging to Asp49 PLA2 class, enzymatically active, and MTX-II to Lys49 PLA2s, catalytically inactive. Treatment of MTX-I with BPB and EDTA reduced drastically its PLA2 and anticoagulant activities, corroborating the importance of residue His48 and Ca2+ ions for the enzymatic catalysis. Both PLA2s induced myotoxic activity and dose-time dependent edema similar to other isolated snake venom toxins from Bothrops and Crotalus genus. The results also demonstrated that MTXs and cationic synthetic peptides derived from their 115-129 C-terminal region displayed cytotoxic activity on human T-cell leukemia (JURKAT) lines and microbicidal effects against Escherichia coli, Candida albicans and Leishmania sp. Thus, these PLA2 proteins and C-terminal synthetic peptides present multifunctional properties that might be of interest in the development of therapeutic strategies against parasites, bacteria and cancer. © 2008 Elsevier Inc. All rights reserved.

Síntese e estudos estrutura/função de um peptídeo extraído da rã Hypsiboas albopunctatus e análogos

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Estudos das propriedades estruturais de análogos substituídos com 'TRP POT.2,7 ou 24' do fragmento com 30 resíduos da região amino-terminal da Esticolisina II

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Atividade coagulante e da toxidade da giroxina nativa e irradiada com Cobalto-60 isolada do veneno de Crotalus durissus terrificus

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Caracterização térmica de sacarose de cana-de-açúcar: amostras de padrão de referência, comercial e purificada

Pós-graduação em Química - IBILCE

Preparação e caracterização de casearinas de Casearia sylvestris como padrão fitoquímico

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Influência da suplementação com citamina E(dl-alfa tocoferol) nas funções de monócitos e polimorfonucleares de eqüinos da raça Árabe submetidos ao exercício físico

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Destilação fracionada do óleo essencial de P. aduncum L. rico em dilapiol

A espécie Piper aduncum L. é uma planta de porte arbustivo, popularmente conhecida na região amazônica como pimenta-de-macaco. Dela, pode ser extraído um óleo essencial, rico em dilapiol, de grande interesse econômico pela sua ação inseticida e combate às pragas na agricultura. Esse bioinseticida surge como alternativa para substituir os inseticidas sintéticos, pois sendo de origem natural não causam danos ao meio ambiente e à saúde do homem. Neste trabalho, foram analisadas as propriedades físicas do óleo essencial de pimenta-de-macaco, obtido por destilação por arraste com vapor que apresentou valores médios do índice de refração igual a 1,516 e massa específica igual a 1,08 g/cm³. Estudou-se o processo de destilação fracionada do óleo essencial, visando concentrar o composto de interesse agregando maior valor econômico, o que viabiliza seu emprego na produção de novos produtos. Nesse processo o composto principal é obtido com elevado grau de pureza. Avaliou-se um modelo matemático para a concentração de dilapiol no fundo do balão de destilação, via análise de regressão, em função do tempo de operação, o qual ajustou muito bem os dados experimentais. A análise dos resultados permite afirmar que o processo de destilação fracionada pode ser empregado para separar os constituintes úteis de óleos essenciais. Isso só é possível, pois os óleos essenciais são constituídos por vários compostos orgânicos voláteis de pontos de ebulição e pressões de vapor diferentes, tornando a separação viável. O maior teor de dilapiol obtido experimentalmente pelo processo de destilação fracionada a vácuo foi de 95 %, operando-se nas condições de vácuo (40 mmHg) e temperatura média da coluna de 122 ºC, obtendo-se um rendimento médio do processo de 41 % (v/v).

Produção de zeólita analcima a partir de caulim amazônico

Na região norte do Brasil são encontradas grandes reservas minerais, as quais tem sido exploradas nas últimas décadas gerando normalmente grande volume de rejeito para o meio ambiente. No caso específico do caulim, o principal produto exportado é para cobertura de papel (commodity) que apresenta baixo valor agregado. Sua produção, também gera um rejeito volumoso composto essencialmente de caulinita, de elevada pureza, porem fora de especificação para cobertura de papel que é descartado e ou utilizado em outras aplicações menos nobre. Como as zeólitas são materiais mais nobres e apresentam na sua estrutura cristalina sílica e alumina este trabalho teve como um dos objetivos o desenvolvimento de processo de produção da zeólita analcima a partir de um rejeito de caulim menos nobre, diatomito e solução de hidróxido de sódio. Por outro lado, os métodos descritos na literatura para obtenção de zeólitas são desenvolvidos em meio alcalino e utilizam normalmente um excesso de hidróxido de sódio no meio reacional ocasionado problema econômico e ambiental. Assim este trabalho descreve o processo de síntese da zeólita analcima semi-contínuo, no qual o excesso de hidróxido utilizado foi recuperado e reutilizado em um novo ciclo de processo. O processo foi desenvolvido em cinco ciclos consecutivos em autoclave através da reação de caulim calcinado, diatomito como fonte de sílica adicional, solução aquosa de hidróxido de sódio fresco e solução de hidróxido de sódio reciclada. A reação do processo foi desenvolvida a 210 °C por 24 h. O produto obtido no final de cada ciclo foi a zeólita analcima caracterizada por fluorescência de raios X, difração de raios, análise termogravimétrica-térmica diferencial, e microscopia eletrônica de varredura. O processo de produção de analcima apresentou elevado rendimento e o reaproveitamento do hidróxido de sódio por meio de reciclo mostrou-se tecnicamente viável.