An archaeological approach to the development of the late medieval peasant house

Archaeological excavation has provided an alternative source of evidence for the development of the late medieval peasant house. It is argued that whilst there was a significant change in building techniques in the decades around 1200 with the adoption of ground-set timbers, the most important factor which led to the survival of houses was a fall in real wages during the thirteenth century. This encouraged peasants to repair existing buildings, rather than replace them with new ones. Alternative traditions of building are also investigated. Stone construction was adopted in a number of areas of England, but in spite of the durability of the material, few medieval peasant buildings of this type have survived in use because of the failure to use lime mortar. Decisions about whether to invest in a building’s renovation will depend on the capital initially expended upon it. This interpretation is considered against the data from the fifteenth century and found to conform satisfactorily. Its implications are considered for the period between 1200 and 1350. Data collected from archaeological excavations combined with the results of dendrochronology on a growing number of closely dated standing buildings suggest that there was a significant ‘cull’ of houses in the period after 1350 as new dwellings were constructed.

Influence of rheology on the quality of surface finish of cement-based mortars

Aesthetics of concrete structures is directly related to the quality of their surface finish. The objective of this investigation was to examine the effect of rheological properties of cement-based mortars on the quality of their surface finish. The study was divided into two phases. Firstly, the influence of the mix composition of mortars, viz. the water to cement (w/c) ratio, the sand content and the superplasticiser (SP) dosage on their rheology was evaluated. Secondly, the surface finish quality was characterised and related to the rheology of the studied systems. Rheology of these materials, i.e. the yield value, was measured using a vane viscometer. The quality of the surface finish was assessed by quantification of the surface air voids by analysing digital photographs of the mould finished sample surfaces. It was found that an increase in the w/c ratio and the SP content decreased the yield value, whilst the increase in the sand content had an opposite effect. When the surface quality is concerned, an increase in the yield value was found to increase the total content of the surface air voids and especially those with size smaller than 1 mm in diameter. Moreover, the analysis of the location of the surface air voids along the height of the sample revealed that with the increase in the yield value their concentration was higher in the bottom section of the analysed samples.

Effect of nanosilica addition on the fresh properties and shrinkage of mortars with fly ash and superplasticizer

The ongoing use of various mineral additions along with chemical admixtures such as superplasticizers justifies the need for further research. Understanding and quantifying their effects and possible synergies on the fresh and hardened properties of cement-based materials is necessary, especially if some of these components are known to have a pozzolanic effect. This paper describes and models the fresh and hardened properties of cement mortars including nanosilica and fly ash, and relates their properties to the proportioning of these materials and the superplasticizer dosage. Mini-slump, Marsh cone and Lombardi cone tests were used to examine the properties of the fresh mortars, and to assess density, plastic shrinkage, and drying shrinkage up to 20 days. The equations presented in this paper make it possible to optimize mortar proportionings to the required levels of performance in both fresh and hardened states.

Mechanism of effluent attack on Portland cement and alkali activated mortars

The alkali activation of waste products has become a widespread topic of research, mainly due to environmental benefits. Portland cement and alkali-activated mortar samples were prepared to compare their resistance to silage effluent which contains lactic acid. The mechanism of attack on each sample has also been investigated.

Rocking behaviour of multi-block columns subjected to pulse-type ground motion accelerations

Ancient columns, made with a variety of materials such as marble, granite, stone or masonry are an important part of the
European cultural heritage. In particular columns of ancient temples in Greece and Sicily which support only the architrave are
characterized by small axial load values. This feature together with the slenderness typical of these structural members clearly
highlights as the evaluation of the rocking behaviour is a key aspect of their safety assessment and maintenance. It has to be noted
that the rocking response of rectangular cross-sectional columns modelled as monolithic rigid elements, has been widely investigated
since the first theoretical study carried out by Housner (1963). However, the assumption of monolithic member, although being
widely used and accepted for practical engineering applications, is not valid for more complex systems such as multi-block columns
made of stacked stone blocks, with or without mortar beds. In these cases, in fact, a correct analysis of the system should consider
rocking and sliding phenomena between the individual blocks of the structure. Due to the high non-linearity of the problem, the
evaluation of the dynamic behaviour of multi-block columns has been mostly studied in the literature using a numerical approach
such as the Discrete Element Method (DEM). This paper presents an introductory study about a proposed analytical-numerical
approach for analysing the rocking behaviour of multi-block columns subjected to a sine-pulse type ground motion. Based on the
approach proposed by Spanos (2001) for a system made of two rigid blocks, the Eulero-Lagrange method to obtain the motion
equations of the system is discussed and numerical applications are performed with case studies reported in the literature and with a
real acceleration record. The rocking response of single block and multi-block columns is compared and considerations are made
about the overturning conditions and on the effect of forcing function’s frequency.
.

Argamassas funcionais para uma construção sustentável

A aposta na sustentabilidade tem conduzido o mercado da construção a procurar novas soluções técnicas e novos materiais, que por serem mais eficientes, conseguem dar resposta aos requisitos cada vez mais exigentes deste sector. A aplicação dos conceitos de sustentabilidade não se pode restringir a novas construções, tendo que prever também as renovações e a reabilitação de edifícios antigos. Assim, novos materiais que sejam desenvolvidos, devem contemplar todas estas vertentes de utilização. Neste trabalho desenvolveram-se argamassas com novas funcionalidades, que contribuem para melhorar os níveis de sustentabilidade dos edifícios, através da incorporação de nanomateriais para armazenamento de calor latente e degradação de poluentes do ar interior. Estudou-se não só o impacto da incorporação destas nanopartículas no estado fresco e endurecido, mas também o seu desempenho do ponto de vista funcional quando integrados na estrutura da argamassa. É possível obter argamassas com capacidade para armazenar calor latente através da incorporação de um material de mudança de fase. Este material constituído por uma mistura de parafinas, consegue armazenar calor e libertálo posteriormente. As composições desenvolvidas podem ser aplicadas em novos projectos ou na reabilitação de edifícios contribuindo para reduzir o consumo energético, melhorando o conforto térmico no interior. Com a redução da factura energética obtém-se uma efectiva diminuição do impacto ambiental, energético e económico do edifício. Para além do armazenamento de calor latente, também se desenvolveram argamassas capazes de eliminar poluentes do ar interior e, simultaneamente, com capacidade de auto-limpeza. Utilizaram-se nanopartículas de dióxido de titânio como aditivo fotocatalítico, tendo-se analisado o efeito da introdução deste aditivo nas argamassas. As composições testadas demonstraram elevada capacidade fotocatalítica e de auto-limpeza, sem comprometer as suas propriedades no estado endurecido. Ao aplicar estas composições na camada de acabamento interior melhora-se a qualidade do ar no interior das habitações e reduz-se a necessidade de utilização de sistemas de ventilação. As argamassas funcionais contribuem para melhorar os níveis de sustentabilidade da construção, tendo impacto económico e ambiental em todo o ciclo de vida do edifício.

Biomass fly ash incorporation in cement based materials

In recent years, pressures on global environment and energy security have led to an increasing demand on renewable energy sources, and diversification of Europe’s energy supply. Among these resources the biomass could exert an important role, since it is considered a renewable and CO2 neutral energy resource once the consumption rate is lower than the growth rate, and can potentially provide energy for heat, power and transports from the same installation. Currently, most of the biomass ash produced in industrial plants is either disposed of in landfill or recycled on agricultural fields or forest, and most times this goes on without any form of control. However, considering that the disposal cost of biomass ashes are raising, and that biomass ash volumes are increasing worldwide, a sustainable ash management has to be established. The main objective of the present study is the effect of biomass fly ashes in cement mortars and concretes in order to be used as a supplementary cementitious material. The wastes analyzed in the study were collected from the fluidized bed boilers and grate boilers available in the thermal power plants and paper pulp plants situated in Portugal. The physical as well as chemical characterisations of the biomass fly ashes were investigated. The cement was replaced by the biomass fly ashes in 10, 20 and 30% (weight %) in order to investigate the fresh properties as well as the hardened properties of biomass fly ash incorporated cement mortar and concrete formulations. Expansion reactions such as alkali silica reaction (ASR), sulphate attack (external and internal) were conducted in order to check the durability of the biomass fly ash incorporated cement mortars and concretes. Alternative applications such as incorporation in lime mortars and alkali activation of the biomass fly ashes were also attempted. The biomass fly ash particles were irregular in shape and fine in nature. The chemical characterization revealed that the biomass fly ashes were similar to a class C fly ash. The mortar results showed a good scope for biomass fly ashes as supplementary cementitious materials in lower dosages (<20%). The poor workability, concerns about the organic content, alkalis, chlorides and sulphates stand as the reasons for preventing the use of biomass fly ash in high content in the cement mortars. The results obtained from the durability tests have shown a clear reduction in expansion for the biomass fly ash mortars/concretes and the binder blend made with biomass fly ash (20%) and metakaolin (10%) inhibited the ASR reaction effectively. The biomass fly ash incorporation in lime mortars did not improve the mortar properties significantly though the carbonation was enhanced in the 15-20% incorporation. The biomass fly ash metakaolin blend worked well in the alkali activated complex binder application also. Portland cement free binders (with 30-40 MPa compressive strength) were obtained on the alkali activation of biomass fly ashes (60-80%) blended with metakaolin (20-40%).

Correlação entre argamassas e betões com base em análise reométrica

O presente trabalho teve como objetivo principal estudar a correlação no estado fresco e no estado endurecido entre argamassas e betões com pozolanas, nomeadamente, um metacaulino e uma diatomite. Este trabalho procurou também otimizar a utilização dos materiais pozolânicos na produção de argamassas e betões. O estudo do comportamento reológico inicia-se com a avaliação da argamassa padrão e do betão padrão, utilizando para tal reómetros adequados a cada material. O comportamento reológico das argamassas com pozolanas foi analisado em função do comportamento da argamassa padrão. Verificou-se que é possível ajustar o comportamento reológico de argamassas com pozolanas ao comportamento da argamassa padrão e, deste modo, obter-se também betões correspondentes (com pozolanas) dentro do intervalo de trabalhabilidade pretendido e pré-definido para o betão padrão. Também foi possível concluir que, até um determinado teor de material pozolânico, se verificava uma correlação entre os parâmetros reológicos (viscosidade e tensão de cedência) das argamassas e os seus betões correspondentes. Na caracterização das argamassas e betões no estado endurecido, verificou-se a existência de uma correlação entre a resistência à compressão das argamassas e as resistências dos betões correspondentes para a maioria das formulações. Quando o ajuste de trabalhabilidade foi efetuado através da alteração do teor de água, apenas as formulações com metacaulino apresentavam uma relação linear entre as resistências das argamassas e a dos betões correspondentes. Usando um agente redutor de água de amassadura para o ajuste de trabalhabilidade, as formulações com metacaulino continuam a apresentar uma relação linear entre as resistências das argamassas e as resistências dos betões. As formulações mistas, com metacaulino e diatomite, também apresentam uma relação linear entre o valor das resistências das argamassas e dos betões. As composições com diatomite não mostram esta relação linear entre a resistência das argamassas e a resistência dos betões, embora exista uma correlação entre elas. O estudo de algumas propriedades no estado endurecido de betões mostrou que a utilização de água como elemento de ajuste de trabalhabilidade diminui sempre a resistência à compressão dos betões com o aumento do teor em pozolana. O uso de um agente redutor de água de amassadura, principalmente no caso da utilização do metacaulino, aumenta a resistência dos betões face ao padrão devido à sua maior reatividade pozolânica relativamente à diatomite. Estas tendências para os resultados observados na resistência mecânica foram também visíveis no módulo de elasticidade e justificáveis pela evolução da microestrutura avaliada conjuntamente por porosimetria, análises térmicas e microscopia eletrónica de varrimento. Finalmente, no estudo da influência dos materiais pozolânicos sobre a durabilidade dos betões, especificamente sobre a resistência à penetração de cloretos, ambas as pozolanas mostraram um efeito bloqueador à penetração de cloretos e, também aqui esse efeito foi mais evidente em composições com metacaulino e na presença de um agente redutor de água de amassadura.

Velocidade da corrosão do aço em argamassas cimentícias modificadas com polímeros

Trabalho Final de Mestrado para obtenção do grau de Mestre em Engenharia Química

A influência das condições de cura nas propriedades das argamassas de cal para revestimentos antigos

Dissertação elaborada no Laboratório Nacional de Engenharia Civil (LNEC) para obtenção do grau de Mestre em Engenharia Civil na Área de Especialização de Edificações no âmbito do protocolo de cooperação entre o ISEL e o LNEC

Argamassas e betões geopoliméricos: estado da arte e potencial de industrialização em Portugal

Dissertação para obtenção do grau de Mestre em Engenharia Civil

Incorporação de resíduo da indústria petrolífera em argamassas de cal hidráulica para a reabilitação de edifícios

Trabalho Final de Mestrado para obtenção do grau de Mestre em Engenharia Civil na Área de Especialização de Edificações

Contribuição para o estudo dos subprodutos de uma ETAR: gradados e areias

Trabalho Final de Mestrado para obtenção do grau de Mestre em Engenharia Civil, na Área de Especialização de Hidráulica

Optimization process of polyester polymer mortars modified with recycled GFRP waste aggregates – application of factorial experiment design-

Glass fibre-reinforced plastics (GFRP), nowadays commonly used in the construction, transportation and automobile sectors, have been considered inherently difficult to recycle due to both: cross-linked nature of thermoset resins, which cannot be remolded, and complex composition of the composite itself, which includes glass fibres, matrix and different types of inorganic fillers. Presently, most of the GFRP waste is landfilled leading to negative environmental impacts and supplementary added costs. With an increasing awareness of environmental matters and the subsequent desire to save resources, recycling would convert an expensive waste disposal into a profitable reusable material. There are several methods to recycle GFR thermostable materials: (a) incineration, with partial energy recovery due to the heat generated during organic part combustion; (b) thermal and/or chemical recycling, such as solvolysis, pyrolisis and similar thermal decomposition processes, with glass fibre recovering; and (c) mechanical recycling or size reduction, in which the material is subjected to a milling process in order to obtain a specific grain size that makes the material suitable as reinforcement in new formulations. This last method has important advantages over the previous ones: there is no atmospheric pollution by gas emission, a much simpler equipment is required as compared with ovens necessary for thermal recycling processes, and does not require the use of chemical solvents with subsequent environmental impacts. In this study the effect of incorporation of recycled GFRP waste materials, obtained by means of milling processes, on mechanical behavior of polyester polymer mortars was assessed. For this purpose, different contents of recycled GFRP waste materials, with distinct size gradings, were incorporated into polyester polymer mortars as sand aggregates and filler replacements. The effect of GFRP waste treatment with silane coupling agent was also assessed. Design of experiments and data treatment were accomplish by means of factorial design and analysis of variance ANOVA. The use of factorial experiment design, instead of the one factor at-a-time method is efficient at allowing the evaluation of the effects and possible interactions of the different material factors involved. Experimental results were promising toward the recyclability of GFRP waste materials as polymer mortar aggregates, without significant loss of mechanical properties with regard to non-modified polymer mortars.