Dynamic stabilization of Rayleigh-Taylor instability of ablation fronts in inertial confinement fusion

One of the most important problems in inertial confinement fusion is how to find a way to mitigate the onset of the Rayleigh-Taylor instability which arises in the ablation front during the compression. In this thesis it is studied in detail the possibility of using for such a purpose the well-known mechanism of dynamic stabilization, already applied to other dynamical systems such as the inverted pendulum. In this context, a periodic acceleration superposed to the background gravity generates a vertical vibration of the ablation front itself. The effects of different driving modulations (Dirac deltas and square waves) are analyzed from a theoretical point of view, with a focus on stabilization of ion beam driven ablation fronts, and a comparison is made, in order to look for optimization.

Sulfur isotope analysis of aerosol particles by NanoSIMS

A new method to measure the sulfur isotopic composition of individual aerosol particles by NanoSIMS has been developed and tested on several standards such as barite (BaSO4), anhydrite (CaSO4), gypsum (CaSO4·2H2O), mascagnite ((NH4)2SO4), epsomite (MgSO4·7H2O), magnesium sulfate (MgSO4·xH2O), thenardite (Na2SO4), boetite (K2SO4) and cysteine (an amino acid). This ion microprobe technique employs a Cs+ primary ion beam and measures negative secondary ions permitting the analysis of sulfur isotope ratios in individual aerosol particles down to 500 nm in size (0.001-0.5 ng of sample material). The grain-to-grain reproducibility of measurements is typically 5‰ (1σ) for micron-sized grains, <5‰ for submicron-sized grains, and <2‰ for polished thin sections and ultra microtome sections which were studied for comparison. The role of chemical omposition (matrix effect) and sample preparation techniques on the instrumental mass fractionation (IMF) of the 34S/32S ratio in the NanoSIMS has been investigated. The IMF varies by ~15‰ between the standards studied here. A good correlation between IMF and ionic radius of the cations in sulfates was observed. This permits to infer IMF corrections even for sulfates for which no isotope standards are available. The new technique allows to identify different types of primary and secondary sulfates based on their chemical composition and to measure their isotopic signature separately. It was applied to marine aerosol samples collected in Mace Head and urban aerosol samples collected in Mainz. It was shown that primary sulfate particles such as sulfate in NaCl or gypsum particles precipitated from ocean water retain the original isotopic signature of their source. The isotopic composition of secondary sulfate depends on the isotopic composition of precursor SO2 and the oxidation pathway. The 34S/32S fractionation with respect to the precursor SO2 is -9‰ for homogeneous oxidation and +16.5‰ for heterogeneous oxidation. This large difference between the isotopic fractionation of both pathways allows identifying the oxidation pathway from which the SO42- in a secondary sulfate particle is derived, by means of its sulfur isotope ratio, provided that the isotopic signature of the precursor SO2 is known. The isotopic composition of the precursor SO2 of secondary sulfates was calculated based on the isotopic composition of particles with known oxidation pathway such as fine mode ammonium sulfate.

Point defects in carbon nanostructures studied by in-situ electron microscopy

In the present work, the formation and migration of point defects induced by electron irradiation in carbon nanostructures, including carbon onions, nanotubes and graphene layers, were investigated by in-situ TEM. The mobility of carbon atoms normal to the layers in graphitic nanoparticles, the mobility of carbon interstitials inside SWCNTs, and the migration of foreign atoms in graphene layers or in layers of carbon nanotubes were studied. The diffusion of carbon atoms in carbon onions was investigated by annealing carbon onions and observing the relaxation of the compressed clusters in the temperature range of 1200 – 2000oC. An activation energy of 5.0±0.3 eV was obtained. This rather high activation energy for atom exchange between the layers not only prevents the exchange of carbon atoms between the layers at lower temperature but also explains the high morphological and mechanical stability of graphite nanostructures. The migration of carbon atoms in SWCNTs was investigated quantitatively by cutting SWCNT bundles repeatedly with a focused electron beam at different temperatures. A migration barrier of about 0.25 eV was obtained for the diffusion of carbon atoms inside SWCNTs. This is an experimental confirmation of the high mobility of interstitial atoms inside carbon nanotubes, which corroborates previously developed theoretical models of interstitial diffusivity. Individual Au and Pt atoms in one- or two-layered graphene planes and MWCNTs were monitored in real time at high temperatures by high-resolution TEM. The direct observation of the behavior of Au and Pt atoms in graphenic structures in a temperature range of 600 – 700°C allows us to determine the sites occupied by the metal atoms in the graphene layer and the diffusivities of the metal atoms. It was found that metal atoms were located in single or multiple carbon vacancies, not in off-plane positions, and diffused by site exchange with carbon atoms. Metal atoms showed a tendency to form clusters those were stable for a few seconds. An activation energy of around 2.5 eV was obtained for the in-plane migration of both Au and Pt atoms in graphene (two-dimensional diffusion). The rather high activation energy indicates covalent bonding between metal and carbon atoms. Metal atoms were also observed to diffuse along the open edge of graphene layers (one-dimensional diffusion) with a slightly lower activation energy of about 2.3 eV. It is also found that the diffusion of metal atoms in curved graphenic layers of MWCNTs is slightly faster than in planar graphene.

Towards a new test of time dilation: Laser spectroscopy on lithium ions stored at a velocity of 33.8 % of the speed of light

The subject of the presented thesis is the accurate measurement of time dilation, aiming at a quantitative test of special relativity. By means of laser spectroscopy, the relativistic Doppler shifts of a clock transition in the metastable triplet spectrum of ^7Li^+ are simultaneously measured with and against the direction of motion of the ions. By employing saturation or optical double resonance spectroscopy, the Doppler broadening as caused by the ions' velocity distribution is eliminated. From these shifts both time dilation as well as the ion velocity can be extracted with high accuracy allowing for a test of the predictions of special relativity. A diode laser and a frequency-doubled titanium sapphire laser were set up for antiparallel and parallel excitation of the ions, respectively. To achieve a robust control of the laser frequencies required for the beam times, a redundant system of frequency standards consisting of a rubidium spectrometer, an iodine spectrometer, and a frequency comb was developed. At the experimental section of the ESR, an automated laser beam guiding system for exact control of polarisation, beam profile, and overlap with the ion beam, as well as a fluorescence detection system were built up. During the first experiments, the production, acceleration and lifetime of the metastable ions at the GSI heavy ion facility were investigated for the first time. The characterisation of the ion beam allowed for the first time to measure its velocity directly via the Doppler effect, which resulted in a new improved calibration of the electron cooler. In the following step the first sub-Doppler spectroscopy signals from an ion beam at 33.8 %c could be recorded. The unprecedented accuracy in such experiments allowed to derive a new upper bound for possible higher-order deviations from special relativity. Moreover future measurements with the experimental setup developed in this thesis have the potential to improve the sensitivity to low-order deviations by at least one order of magnitude compared to previous experiments; and will thus lead to a further contribution to the test of the standard model.

A scanning electron microscope for ultracold quantum gases

This thesis presents a new imaging technique for ultracold quantum gases. Since the first observation of Bose-Einstein condensation, ultracold atoms have proven to be an interesting system to study fundamental quantum effects in many-body systems. Most of the experiments use optical imaging rnmethods to extract the information from the system and are therefore restricted to the fundamental limitation of this technique: the best achievable spatial resolution that can be achieved is comparable to the wavelength of the employed light field. Since the average atomic distance and the length scale of characteristic spatial structures in Bose-Einstein condensates such as vortices and solitons is between 100 nm and 500 nm, an imaging technique with an adequate spatial resolution is needed. This is achieved in this work by extending the method of scanning electron microscopy to ultracold quantum gases. A focused electron beam is scanned over the atom cloud and locally produces ions which are subsequently detected. The new imaging technique allows for the precise measurement of the density distribution of a trapped Bose-Einstein condensate. Furthermore, the spatial resolution is determined by imaging the atomic distribution in one-dimensional and two-dimensional optical lattices. Finally, the variety of the imaging method is demonstrated by the selective removal of single lattice site. rn

Das Aerosol-Ionenfallen-Massenspektrometer (AIMS) : Aufbau, Charakterisierung und Feldeinsatz

Um die in der Atmosphäre ablaufenden Prozesse besser verstehen zu können, ist es wichtig dort vorhandene Partikel gut charakterisieren zu können. Dazu gehört unter anderem die Bestimmung der chemischen Zusammensetzung der Partikel. Zur Analyse insbesondere organischer Partikel wurde dazu in einer früheren Promotion das Aerosol-Ionenfallen-Massenspektrometer (AIMS) entwickelt.Im Rahmen dieser Arbeit wurden Entwicklungsarbeiten durchgeführt, um die Charakteristiken des Prototypen zu verbessern sowie es für den Feldeinsatz tauglich zu machen. Die durchgeführten Veränderungen betreffen mechanische und elektrische Komponenten sowie das LabView Steuerungsprogramm. So wurde z.B. die Ionenquelle derart modifiziert, dass die Ionen nicht mehr permanent erzeugt werden, sondern nur innerhalb des Zeitraums wenn sie auch in der Ionenfalle gespeichert werden können. Durch diese Modifikation konnte das Signal-zu-Rausch Verhältnis deutlich verbessert werden. Nach Beendigung der Umbauten wurden in ausführlichen Laborstudien die einzelnen Instrumentenparameter detailliert charakterisiert. Neben den Spannungen die zur Fokussierung oder zur Speicherung der Ionen in der Ionenfalle dienen, wurden die unterschiedlichen Arten der resonanten Anregung, mittels der die Ionen in der Ionenfalle gezielt zu Schwingungen angeregt werden können, sehr genau untersucht. Durch eine gezielte Kombination der unterschiedlichen Arten der resonanten Anregung ist es möglich MSn-Studien durchzuführen. Nach erfolgreicher Charakterisierung konnte in weiteren Laborstudien die MSn-Fähigkeit des AIMS demonstriert werden. Für Tryptophan (C11H12N2O2) wurde anhand von MS4-Studien ausgehend von m/z 130 ein möglicher Fragmentierungsweg identifiziert. Für die einzelnen Stufen der MS4-Studien wurden die Nachweisgrenzen abgeschätzt. Im Rahmen der PARADE (PArticles and RAdicals: Diel observations of the impact of urban and biogenic Emissions) Messkampagne im August/September 2011 auf dem kleinen Feldberg in der Nähe von Frankfurt am Main wurde die Feldtauglichkeit des AIMS demonstriert. Die Nachweisgrenzen liegen für eine Mittelungszeit von 60 Minuten für Organik bei 1,4 µg m-3, für Nitrat bei 0,5 µg m-3 und für Sulfat bei 0,7 µg m-3, was ausreichend ist um atmosphärisches Aerosol messen zu können. Dies ist ein signifikanter Fortschritt im Vergleich zum Prototypen, der aufgrund schlechter Reproduzierbarkeit und Robustheit noch nicht feldtauglich war. Im Vergleich zum HR-ToF-AMS, einem Standard-Aerosolmassenspektrometer, zeigte sich, dass beide Instrumente vergleichbare Trends für die Spezies Nitrat, Sulfat und Organik messen.

Kollineare Laserspektroskopie an radioaktiven Praseodymionen und Cadmiumatomen

Die Analyse optischer Spektren liefert einen kernmodellunabhängigen Zugang zur Bestimmung der Kernspins, Ladungsradien und elektromagnetischen Momente von Atomkernen im Grundzustand und von langlebigen Isomeren. Eine der vielseitigsten Methoden zur optischen Spektroskopie an kurzlebigen Isotopen ist die kollineare Laserspektroskopie. Im Rahmen dieser Arbeit wurde zum einen die TRIGA-LASER Strahlstrecke am Institut für Kernchemie der Universität Mainz durch die Implementierung einer neuen offline Oberflächenionenquelle für hohe Verdampfungstemperaturen und eines Strahlanalysesystems weiterentwickelt. Zum anderen wurde kollineare Laserspektroskopie an kurzlebigen Praseodym- und Cadmiumisotopen an ISOLDE/CERN durchgeführt. Die neue Ionenquelle ermöglichte dabei den Test der kollinearen Laserspektroskopie an Praseodymionen am TRIGA-LASER Experiment. Die Spektroskopie der Prasdeodymionen motivierte sich aus der Beobachtung einer zeitlichen Modulation der EC-Zerfallsrate von wasserstoffähnlichem 140Pr58+. Für die Erklärung dieser sogenannten GSI Oszillationen wird unter anderem das magnetische Moment des Kerns benötigt, welches bislang noch nicht experimentell bestimmt wurde. Zudem wurde für wasserstoffähnliches 140Pr58+ überraschenderweise eine kleinere EC-Zerfallskonstante gemessen als für heliumähnliches 140Pr57+. Die Erklärung dieses Phänomens setzt ein positives magnetisches Moment voraus. Bei der Spektroskopie am COLLAPS Experiment wurden erstmals die magnetischen Momente von 135Pr, 136Pr und 137Pr vermessen. Aufgrund zu geringer Produktionsraten war die Spektroskopie des gewünschten Isotops 140Pr jedoch nicht erfolgreich. Die Untersuchung der Cadmiumisotope ist kernphysikalisch motiviert. In der Zinnregion erstrecken sich die Isotope über die beiden magischen Zahlen N=50 und N=82 bei gleichzeitiger Nähe des Z=50 Schalenabschlusses. Hier können verschiedene Kernmodelle getestet werden, die sich beispielsweise hinsichtlich der Stärke des N=82 Schalenabschlusses widersprechen. Diese Arbeit berichtet über erste Ergebnisse der Spektroskopie an Cadmiumatomen, die sich über die Isotope 106−124,126Cd sowie die zugehörigen langlebigen I=11/2− Isomere erstreckt. Die zuvor experimentell bekannten oder aus dem erweiterten Schalenmodell abgeleiteten Kernspins konnten für alle Isotope bis auf 119Cd bestätigt werden. Der Kernspin von 119Cd wurde eindeutig zu I=1/2 bestimmt. Die elektrischen Quadrupolmomente der Isomere zeigen ein bemerkenswert lineares Verhalten in Abhängigkeit von der Neutronenzahl und dies über die eigentliche Kapazität der 1h11/2 Unterschale hinaus. Die Änderungen der mittleren quadratischen Ladungsradien zeigen den auch an Indium- und Zinnisotopen beobachteten stetigen Verlauf. Der lineare Anteil passt sehr gut zu den Berechnung des Tröpfchenmodells in der Parametrisierung nach Berchidevsky und Tondeur. Die Differenzen der mittleren quadratischen Ladungsradien zwischen Grund- und isomeren Zustand der ungeraden Cadmiumisotope zeigen einen interessanten parabolischen Verlauf mit einem Minimum zwischen A=117 und A=119.

Implementierung der Laserionenquellenfalle LIST bei ISOLDE und Validierung der Spezifikationen Effizienz und Selektivität

Die Funktionsweise der Laserionenquellenfalle LIST, sowie deren Implementierung bei der Forschungseinrichtung ISOLDE am CERN als neue Standard-Ionenquelle und die ermittelten Spezifikationen Effizienz und Selektivität werden vorgestellt.rnrnDurch die Implementierung der LIST bei ISOLDE konnte on-line mit Hilfe von Radionukliden ein Minimalwert zur Unterdrückung von Kontaminationen durch die LIST bestimmt werden. Die erfolgreiche Unterdrückung von Francium-Kontamination ermöglichte es, neue Messdaten für den mittleren Ladungsradius und die Hyperfeinstruktur für Po-217 zu erzeugen.rnrnUm die Funktionalität der LIST bei ISOLDE hinsichtlich der Ionisationseffizienz gegenüber anderen Ionenquellen einzuordnen, wurden in Mainz am RISIKO-Massenseparator mit der bereits existierenden Standard-Ionenquelle RILIS und der LIST die Effizienzen bestimmt und miteinander verglichen. Es konnte gezeigt werden, dass die LIST im Modus hoher Ionisationseffizienz eine vergleichbare Effizienz aufweist wie die RILIS. Im Modus zur Produktion eines hochreinen Ionenstrahls ist die Ionisationseffizienz gegenüber der RILIS reduziert.rnrnDa die Bestimmung der Selektivität im On-line-Betrieb aufwendig und zeitintensiv ist, wurde die Reinheit des Ionenstrahls am RISIKO-Massenseparator mittels Laufzeitmessungen der Ionen off-line bestimmt und analysiert. Die Zeitstrukturen der RILIS ermöglichen einerseits Rückschlüsse auf die Reinheit des Ionenstrahls zu ziehen, andererseits konnte auch die Ionisation außerhalb des Atomisators, in dem überwiegend die resonante Ionisation stattfindet, nachgewiesen werden. Durch diesen Nachweis kann der Effizienzverlust während der Produktion eines hochreinen Ionenstrahls erklärt werden. Zudem bietet er einen Ansatz für weitere Entwicklungsarbeiten der LIST zur Steigerung der Effizienz.rnrnEine Übertragung der Messergebnisse zur Zeitstruktur der RILIS auf die LIST eröffnet neue Möglichkeiten zur Steigerung deren Selektivität im massenselektiven Mode. Dieser wurde anhand von Simulationen überprüft und mit Messungen an Kalium experimentell quantifiziert.

Single- and double-electron transfer reactions of ground and metastable state Ar2+ ions

Electron transfer cross sections have been measured for reactions of Ar2+ ions with Ar, N2, O2, CO2, CH4 and C2H6. Time-of-flight techniques have been used to measure both fast neutral Ar0 and fast Ar+ products from single- and double-electron transfer processes involving Ar2+ ions with 4.0 to 7.0 keV impact energies. Incident Ar2+ ions have produced by controlled electron impact ionisation of argon atoms. Reactions have been examined as a function of ionising electron energy and cross sections determined for ground state Ar2+(3P) ions. Charge transfer cross sections have been determined to be in the range of 3*10-16 cm2 for the systems examined. Double-electron transfer cross sections are the same order of magnitude as those measured for the corresponding single-electron transfer reactions. The state distribution of the reactant ion beam has been estimated and electron transfer cross sections obtained for single- and double-electron transfer reactions of metastable Ar2+ions. The magnitudes of electron transfer cross sections in individual systems are similar for both ground and metastable state Ar2+ reactions.

Hall-effect thruster-cathode coupling : the effect of cathode position and magnetic field topology

Hall-effect thruster (HET) cathodes are responsible for the generation of the free electrons necessary to initiate and sustain the main plasma discharge and to neutralize the ion beam. The position of the cathode relative to the thruster strongly affects the efficiency of thrust generation. However, the mechanisms by which the position affects the efficiency are not well understood. This dissertation explores the effect of cathode position on HET efficiency. Magnetic field topology is shown to play an important role in the coupling between the cathode plasma and the main discharge plasma. The position of the cathode within the magnetic field affects the ion beam and the plasma properties of the near-field plume, which explains the changes in efficiency of the thruster. Several experiments were conducted which explored the changes of efficiency arising from changes in cathode coupling. In each experiment, the thrust, discharge current, and cathode coupling voltage were monitored while changes in the independent variables of cathode position, cathode mass flow and magnetic field topology were made. From the telemetry data, the efficiency of the HET thrust generation was calculated. Furthermore, several ion beam and plasma properties were measured including ion energy distribution, beam current density profile, near-field plasma potential, electron temperature, and electron density. The ion beam data show how the independent variables affected the quality of ion beam and therefore the efficiency of thrust generation. The measurements of near-field plasma properties partially explain how the changes in ion beam quality arise. The results of the experiments show that cathode position, mass flow, and field topology affect several aspects of the HET operation, especially beam divergence and voltage utilization efficiencies. Furthermore, the experiments show that magnetic field topology is important in the cathode coupling process. In particular, the magnetic field separatrix plays a critical role in impeding the coupling between cathode and HET. Suggested changes to HET thruster designs are provided including ways to improve the position of the separatrix to accommodate the cathode.

Integration of room temperature single electron transistor with CMOS subsystem

The single electron transistor (SET) is a charge-based device that may complement the dominant metal-oxide-semiconductor field effect transistor (MOSFET) technology. As the cost of scaling MOSFET to smaller dimensions are rising and the the basic functionality of MOSFET is encountering numerous challenges at dimensions smaller than 10nm, the SET has shown the potential to become the next generation device which operates based on the tunneling of electrons. Since the electron transfer mechanism of a SET device is based on the non-dissipative electron tunneling effect, the power consumption of a SET device is extremely low, estimated to be on the order of 10^-18J. The objectives of this research are to demonstrate technologies that would enable the mass produce of SET devices that are operational at room temperature and to integrate these devices on top of an active complementary-MOSFET (CMOS) substrate. To achieve these goals, two fabrication techniques are considered in this work. The Focus Ion Beam (FIB) technique is used to fabricate the islands and the tunnel junctions of the SET device. A Ultra-Violet (UV) light based Nano-Imprint Lithography (NIL) call Step-and-Flash- Imprint Lithography (SFIL) is used to fabricate the interconnections of the SET devices. Combining these two techniques, a full array of SET devices are fabricated on a planar substrate. Test and characterization of the SET devices has shown consistent Coulomb blockade effect, an important single electron characteristic. To realize a room temperature operational SET device that function as a logic device to work along CMOS, it is important to know the device behavior at different temperatures. Based on the theory developed for a single island SET device, a thermal analysis is carried out on the multi-island SET device and the observation of changes in Coulomb blockade effect is presented. The results show that the multi-island SET device operation highly depends on temperature. The important parameters that determine the SET operation is the effective capacitance Ceff and tunneling resistance Rt . These two parameters lead to the tunneling rate of an electron in the SET device, Γ. To obtain an accurate model for SET operation, the effects of the deviation in dimensions, the trap states in the insulation, and the background charge effect have to be taken into consideration. The theoretical and experimental evidence for these non-ideal effects are presented in this work.

Untersuchung zur Reduzierung des Verzugs durch Vorwärmung bei der Herstellung von Aluminiumbauteilen mittels SLM

Das generative Fertigungsverfahren Selective Laser Melting (SLM) wird zur direkten Herstellung von metallischen Funktionsbauteilen verwendet. Während des Bauprozesses entstehen durch den schichtweisen Aufbau und die lokale Energieeinbringung mittels eines fokussierten Laserstrahls thermisch induzierte Eigenspannungen, die zu Verzug des Bauteils oder von Bauteilbereichen führen können. Üblicherweise werden die Verzüge durch Stützstrukturen zwischen Bauteil und Substratplatte verhindert. Jedoch ist es nicht immer möglich alle Bereiche eines Bauteils, je nach Komplexität der Geometrie oder Zugänglichkeit, mit Stützstrukturen zu versehen bzw. diese wieder zu entfernen. Durch eine Vorwärmung der Substratplatte während des Bauprozesses können die Verzüge reduziert oder ganz vermieden werden. Jedoch ist bisher keine systematische Untersuchung des Einflusses der Vorwärmung auf Verzüge von Aluminium Bauteilen durchgeführt worden. Ziel dieser Arbeiten ist daher die systematische Untersuchung der Auswirkung einer Vorwärmung beim SLM von Aluminiumbauteilen und die Ermittlung der geeigneten Vorwärmtemperatur, bei der nahezu keine Verzüge mehr entstehen. Eine signifikante Verzugsreduzierung im Vergleich zu den Verzügen ohne Vorwärmung zeigt sich ab einer Vorwärmtemperatur von 150°C. Bei einer Vorwärmtemperatur von 250°C sind im Rahmen der Messgenauigkeit unabhängig von der untersuchten Twincantilever Testgeometrie keine Verzüge mehr feststellbar. Neben der Reduzierung der Verzüge verhindert die Vorwärmung außerdem spannungsbedingte Risse im Bauteil, die ohne Vorwärmung zum Abreißen von Teilen der Testgeometrie führen können. Mit 90 HV 0,1 bei 250°C Vorwärmtemperatur ist die Härte größer als die geforderte Mindesthärte nach DIN EN 1706 von Druckgussbauteilen aus dem Werkstoff AlSi10Mg. Aus diesem Ergebnis kann abgeleitet werden, dass eine Vorwärmtemperatur von 250°C geeignet ist, Bauteile aus dem Werkstoff AlSi10Mg mit SLM defektfrei und prozesssicher herzustellen und Verzüge vollständig zu vermeiden.

Clutter elimination for deep clinical optoacoustic imaging using localised vibration tagging (LOVIT)

This paper investigates a novel method which allows clutter elimination in deep optoacoustic imaging. Clutter significantly limits imaging depth in clinical optoacoustic imaging, when irradiation optics and ultrasound detector are integrated in a handheld probe for flexible imaging of the human body. Strong optoacoustic transients generated at the irradiation site obscure weak signals from deep inside the tissue, either directly by propagating towards the probe, or via acoustic scattering. In this study we demonstrate that signals of interest can be distinguished from clutter by tagging them at the place of origin with localised tissue vibration induced by the acoustic radiation force in a focused ultrasonic beam. We show phantom results where this technique allowed almost full clutter elimination and thus strongly improved contrast for deep imaging. Localised vibration tagging by means of acoustic radiation force is especially promising for integration into ultrasound systems that already have implemented radiation force elastography.

AMS-C14 analysis of graphite obtained with an Automated Graphitization Equipment (AGE III) from aerosol collected on quartz filters

AMS-14C applications often require the analysis of small samples. Such is the case of atmospheric aerosols where frequently only a small amount of sample is available. The ion beam physics group at the ETH, Zurich, has designed an Automated Graphitization Equipment (AGE III) for routine graphite production for AMS analysis from organic samples of approximately 1 mg. In this study, we explore the potential use of the AGE III for graphitization of particulate carbon collected in quartz filters. In order to test the methodology, samples of reference materials and blanks with different sizes were prepared in the AGE III and the graphite was analyzed in a MICADAS AMS (ETH) system. The graphite samples prepared in the AGE III showed recovery yields higher than 80% and reproducible 14C values for masses ranging from 50 to 300 lg. Also, reproducible radiocarbon values were obtained for aerosol filters of small sizes that had been graphitized in the AGE III. As a study case, the tested methodology was applied to PM10 samples collected in two urban cities in Mexico in order to compare the source apportionment of biomass and fossil fuel combustion. The obtained 14C data showed that carbonaceous aerosols from Mexico City have much lower biogenic signature than the smaller city of Cuernavaca.

Radiochemical determination of 129I and 36Cl in MEGAPIE, a proton irradiated lead-bismuth eutectic spallation target

The concentrations of the long-lived nuclear reaction products 129I and 36Cl have been measured in samples from the MEGAPIE liquid metal spallation target. Samples from the bulk target material (lead-bismuth eutectic, LBE), from the interface of the metal free surface with the cover gas, from LBE/steel interfaces and from noble metal absorber foils installed in the cover gas system were analysed using Accelerator Mass Spectrometry at the Laboratory of Ion beam Physics at ETH Zürich. The major part of 129I and 36Cl was found accumulated on the interfaces, particularly at the interface of LBE and the steel walls of the target container, while bulk LBE samples contain only a minor fraction of these nuclides. Both nuclides were also detected on the absorber foils to a certain extent (≪ 1% of the total amount). The latter number is negligible concerning the radio-hazard of the irradiated target material; however it indicates a certain affinity of the absorber foils for halogens, thus proving the principle of using noble metal foils for catching these volatile radionuclides. The total amounts of 129I and 36Cl in the target were estimated from the analytical data by averaging within the different groups of samples and summing up these averages over the total target. This estimation could account for about half of the amount of 129I and 36Cl predicted to be produced using nuclear physics modelling codes for both nuclides. The significance of the results and the associated uncertainties are discussed.