Nanostructure and mechanical measurement of highly oriented lamellae of melt-drawn HDPE by scanning probe microscopy

Scanning probe microscopy was used to simultaneously determine the molecular chain structure and intrinsic mechanical properties, including anisotropic elastic modulus and friction, for lamellae of highly oriented high-density polyethylene (HDPE) obtained by the melt-drawn method. The molecular-scale image of the highly oriented lamellae by friction force microscopy (FFM) clearly shows that the molecular chains are aligned parallel to the drawing direction, and the periodicities along and perpendicular to the drawing direction are 0.26 and 0.50 nm, respectively. The results indicate that the exposed planes of the lamellae resulting from the melt-drawn method are (200), which is consistent with results of transmission electron microscopy and electron diffraction. Because of the high degree of anisotropy in the sample, coming from alignment of the molecular chains along the drawing direction, the measured friction force, F, determined by FFM is strongly dependent on the angle, theta, between the scanning direction and the chain axis. The force increases as theta is increased from 0 degrees (i.e., parallel to the chain axis) to 90 degrees (i.e., perpendicular to the chain axis). The structural anisotropy was also found to strongly influence the measurements of the transverse chain modulus of the polymer by the nanoindentation technique. The measured value of 13.8 GPa with transverse modulus was larger than the value 4.3 GPa determined by wide-angle X-ray diffraction, which we attributed to anisotropic deformation of the lamellae during nanoindentation measurements that was not accounted for by the elastic treatment we adopted from Oliver and Pharr. The present approach using scanning probe microscopy has the advantage that direct correlations between the nanostructure, nanotribology, and nanomechanical properties of oriented samples can be determined simultaneously and simply.

Experimental measurement of polyethylene chain modulus by scanning force microscopy

Nanoindentation technique and scanning force microscopy have been used to measure directly the polyethylene modulus along the chain axis. Single crystals of polyethylene were employed in order to obtain well-aligned chain segments. To minimize effects of scanner creep, a Z scan rate of 3 Hz was employed. The "X Rotate" value of 25 degrees was selected to eliminate effects of lateral tip motion. The results were analyzed by the Oliver -Pharr method for which direct observation and measurement of the contact area are not required. Considering the influence of tip roundness on the projected contact area, the nanoindentation results were analyzed by the Sawa method. The chain modulus obtained from the thinner polyethylene single crystal sample was 204 +/- 21 GPa by the Oliver-Pharr method and 168 +/- 17 GPa by the Sawa method. The lower values than expected were due to substrate effects and anisotropy of chain deformation during nanoindentation. An extrapolation of the chain modulus obtained by various strains to zero nanoindentation eliminated the effect of substrate and anisotropy of chain deformation. The corresponding chain modulus obtained from the thicker sample was 278 GPa by the Oliver-Pharr method and 267 GPa by the Sawa method, respectively, in better agreement with the value of 340 Cpa determined theoretically. (C) 2001 Elsevier Science Ltd. All rights reserved.

STUDY ON MEASUREMENT OF DIFFUSION-COEFFICIENT OF LI ATOM IN LIQUID ALUMINUM

The tess potential-concentration curve was first applied to measure the concentration of an alloy. Attempt to use the V-c curve of Al-Li alloy in measuring the diffusion coeffictent of Li atom in liquid aluminium with anode chronopotentiometry at 720℃, was made and D_(Li/Al=4.94×10~(-5)cm~2·s~(-1) was obtained. The value is well consistent wish the theoretical value, D_(Li/Al)=4.85×10~(-5)cm~2·s~(-1) in terms of Stokes-Einstein equation.

社会发展与中国人人格变迁——控制测验理论与工具的变异后不同时期的中国人人格差异研究

In non-western society，researches on social development and personality change focused on economic development and social modernization. The present study is aimed at exploring the relationship between the social transformation and personality changes of Chinese people by using so-called indigenous personality measurement of CPAI (Chinese Personality Assessment Inventory). Meanwhile, the influence of CPAI measurement itself and measurement theory were also taken into consideration. In study 1, two sets of CPAI data collected in a 10 year interval were analyzed. At the same time, the CPAI-2 data was analyzed in terms of modernization level of various cities from which the data were collected. However, this study didn’t consider the importance of “equivalence” of the measurement, CPAI. In study 2, we detected DIF (Differential item functioning) across the different period groups to confirm if CPAI was equal to people in different period. In this process, both CTT and IRT method were used. The outcome reminded us that there were some DIF items. In study 3, to make sure that the personality measurement is fair to people in different period, we only saved those items whose DIF effect size lower than 0.01, and used IRT method to estimate test-taker’s personality. Then, cohort analysis was used to explore the pattern of personality change of Chinese people. In study 4, we factor-analyzed the DIF items to find the relation between social transformation and the latent personality variable which were composed of DIF items. From these 4 studies, we could got the following conclusions: (1) The CPAI 22 traits could be divided into two categories, with the changing of age, period and cohort, type I traits didn’t change, they were Logical vs Affective Orientation, Enterprise, Responsibility, Inferiority vs Self-Acceptance, Optimism vs Pessimism, Face, Family, Defensive, Graciousness vs Meanness; While with the changing of age, period and cohort, type II traits changed, they were Leadership, Self vs. Social Orientation, Veraciousness vs Slickness, Traditionalism vs Modernity, Harmony, Renqing, Meticulousness, Extraversion vs Introversion, Emotionality, Practical Mindedness, Internal vs External Locus of Control, Thrift vs Extravagance, Discipline. Meanwhile DIF items measured 5 psychologycial characteristics which changed greatly with the changing of age, period and cohort, they were Life attitude of Cynicism-realism, Psychological maladjustment, Coping style of Waiyuanneifang, Self-efficacy, the value of Individualism. (2) In sum, Chinese people in 1992 were more traditional than those in 2001, and with the 10-year of rapid development, according to the market economy’s needs, Chinese people became more individualism. (3) The DIF method of CTT and IRT were comparable. But, in generally, IRT method was more accurate and valid in detecting DIF as were as estimating personality. (4) The DIF outcomes showed that CPAI had good item validity. Meanwhile, it’s possible to develop a subscale by using CPAI items to assess some psychological characteristics. In this current study, according to their stability and variability, we could divided personality traits and psychological characteristics into 3 categories, and the outcome supported the hypothesis of “Six Factor Model”, these foundings were of some theoretic meanings. Meanwhile, as the relation between social development and personality change being explored, it certain help Chinese people cope with the rapid changing society. In this study, we also found that it’s possible to develop a subscale by using CPAI items to assess obverse personality traits and it had some practical use. Furthermore, the use of different measurement theory and cohort analysis embodied some innovation in methodology.

Measurement of ratios of fragmentation fractions for bottom hadrons in pp̄ collisions at s=1.96TeV

This paper describes the first measurement of b-quark fragmentation fractions into bottom hadrons in Run II of the Tevatron Collider at Fermilab. The result is based on a 360pb-1 sample of data collected with the CDF II detector in pp̄ collisions at s=1.96TeV. Semileptonic decays of B̄0, B-, and B̄s0 mesons, as well as Λb0 baryons, are reconstructed. For an effective bottom hadron pT threshold of 7GeV/c, the fragmentation fractions are measured to be fu/fd=1.054±0.018(stat)-0.045+0.025(sys)±0. 058(B), fs/(fu+fd)=0.160±0.005(stat)-0.010+0.011(sys)-0.034+0.057(B), and fΛb/(fu+fd)=0.281±0.012(stat)-0.056+0.058(sys)-0.087+0.128(B), where the uncertainty B is due to uncertainties on measured branching ratios. The value of fs/(fu+fd) agrees within one standard deviation with previous CDF measurements and the world average of this quantity, which is dominated by LEP measurements. However, the ratio fΛb/(fu+fd) is approximately twice the value previously measured at LEP. The approximately 2σ discrepancy is examined in terms of kinematic differences between the two production environments. © 2008 The American Physical Society.

Performance measurement and benchmarking of a major innovation programme

Purpose: The purpose of this paper is to describe the problems encountered and the solutions developed when using benchmarking and key performance indicators (KPIs) to monitor a major UK social house building innovation (change) programme. The innovation programme sought improvements to both the quality of the house product and the procurement process. Design/methodology/approach: Benchmarking and KPIs were used to quantify performance and in-depth case studies to identify underlying cause and effect relationships within the innovation programme. Findings: The inherent competition between consortium members; the complexity of the relationship between the consortium and its strategic partner; the lack of an authoritative management control structure; and the rapidly changing nature of the UK social housing market all proved problematic to the development of a reliable and robust monitoring system. These problems were overcome by the development of multi-dimensional benchmarking model that balanced the needs and aspirations of the individual organisations with the broader objectives of the consortium. Research limitations/implications: Whilst the research methodology provides insight into the factors that affected the performance of a major innovation programme its findings may not be representative of all projects. Practical implications: The lessons learnt should assist those developing benchmarking models for multi-client consortia. Originality/value: The work reported in this paper describes an inclusive approach to benchmarking in which a multiple client group and their strategic partner sought to work together for shared gain. Very few papers have addressed this issue.

Some Practical Considerations In The Measurement Of Pollution Effects On Bivalve Mollusks And Some Possible Ecological Consequences

A consideration of some physiological (rates of oxygen consumption, the scope for growth) and cellular (the cytochemical latency of a lysosomal enzyme) processes in bivalve molluscs suggests that animal size and seasonal changes related to the gametogenic cycle are important sources of natural variability. Correcting for size using regression techniques, and limiting measurements to one part of the gametogenic cycle, reduces observed natural variability considerably. Differences between populations are then still apparent, but the results of laboratory experiments with hydrocarbons from crude oil suggest that it should be possible to detect sub-lethal effects due to pollution (the ‘signal’) in the presence of the remaining natural variability (the ‘noise’). Statistical considerations, taken together with results from current studies on Mytilus edulis and Scobicularia plana, indicate that sample sizes of 10–15 individuals should suffice for the detection of possible pollution effects. The physiological effects to be expected in the presence of sub-lethal levels of polluting hydrocarbons are on a scaie that can cause significant ecological damage to a population through a reduction in fecundity and the residual reproductive value of the individuals.

Identification of an unknown b-agonist in feed by liquid chromatography/bioassay/quadrupole time-of-flight tandem mass spectrometry with accurate mass measurement.

A new approach to the search for residues of unknown growth promoting agents such as anabolic steroids and -agonists in feed is presented. Following primary extraction and clean-up, samples are separated using gradient liquid chromatography (LC). The effluent is split towards two identical 96-well fraction collectors and an optional electrospray quadrupole time-of-flight mass spectrometry (QTOFMS) system for accurate mass measurement. One 96-well plate is used for a bioassay (enzyme-immuno assay, receptor assay) and will detect the bioactivity and position of the relevant peak in the chromatogram. The positive well in the second 96-well plate is used for identification by LC/QTOFMS/MS. The value of this LC/bioassay/QTOFMS/MS methodology is highlighted by the finding and structure elucidation of a new -agonist in a feed extract.

Measurement and interpretation of the mid-infrared properties of single crystal and polycrystalline gold

The contribution of electron-phonon scattering and grain boundary scattering to the mid-IR (lambda = 3.392 mum) properties of An has been assessed by examining both bulk, single crystal samples-Au(1 1 1) and Au(1 1 0)-and thin film, polycrystalline An samples at 300 K and 100 K by means of surface plasmon polariton excitation. The investigation constitutes a stringent test for the in-vacuo Otto-configuration prism coupler used to perform the measurements, illustrating its strengths and limitations. Analysis of the optical response is guided by a physically based interpretation of the Drude model. Relative to the reference case of single crystal Au at 100 K (epsilon = - 568 + i17.5), raising the temperature to 300 K causes increased electron-phonon scattering that accounts for a reduction of similar to40 nm in the electron mean free path. Comparison of a polycrystalline sample to the reference case determines a mean free path due to grain boundary scattering of similar to 17 nm, corresponding to about half the mean grain size as determined from atomic force microscopy and indicating a high reflectance coefficient for the An grain boundaries. An analysis combining consideration of grain boundary scattering and the inclusion of a small percentage of voids in the polycrystalline film by means of an effective medium model indicates a value for the grain boundary reflection coefficient in the range 0.55-0.71. (C) 2005 Elsevier B.V. All rights reserved.

'Superluminal' tunnelling as a weak measurement effect

We exploit the analogy between the transfer of a pulse across a scattering medium and Aharonov's weak measurements to resolve the long standing paradox between the impossibility to exceed the speed of light and the seemingly "superluminal" behavior of a tunneling particle in the barrier or a photon in a "fast-light" medium. We demonstrate that superluminality occurs when the value of the duration tau spent in the barrier is uncertain, whereas when tau is known accurately, no superluminal behavior is observed. In all cases only subluminal durations contribute to the transmission which precludes faster-than-light information transfer, as observed in a recent experiment.

Absolute Absorption Cross-Section Measurement of a Submonolayer film on a silica microresonator

Conventional absorption spectroscopy is not nearly sensitive enough for quantitative overtone measurements on submonolayer coatings. While cavity-enhanced absorption detection methods using microresonators have the potential to provide quantitative absorption cross sections of even weakly absorbing submonolayer films, this potential has not yet been fully realized. To determine the absorption cross section of a submonolayer film of ethylene diamine (EDA) on a silica microsphere resonator, we use phase-shift cavity ringdown spectroscopy simultaneously on near-IR radiation that is Rayleigh backscattered from the microsphere and transmitted through the coupling fiber taper. We then independently determine both the coupling coefficient and the optical loss within the resonator. Together with a coincident measurement of the wavelength frequency shift, an absolute overtone absorption cross section of adsorbed EDA, at submonolayer coverage, was obtained and was compared to the bulk value. The smallest quantifiable absorption cross section is σmin 2.7 × 10−12 cm2. This absorption cross section is comparable to the extinction coefficients of, e.g., single gold nanoparticles or aerosol particles. We therefore propose that the present method is also a viable route to absolute extinction measurements of single particles.

Fairness measurement for adaptive packet schedulers

An equation is presented for calculating the fairness of dynamically adaptive packet schedulers such as dynamic weighted fair queuing (DWFQ). The fairness of static packet schedulers such as weighted fair queue (WFQ) can be found using the widely accepted Worst-case Fair Index. The fairness of DWFQ can be measured using an Adapted Worst-case Fairness Index (AWFI). The AWFI enables a direct comparison of fairness properties of the DWFQ or other dynamically adaptive schedulers with static/non-adaptive schedulers.

Developing a conceptual model of lead performance measurement and benchmarking: A multiple case analysis

Purpose: Environmental turbulence including rapid changes in technology and markets has resulted in the need for new approaches to performance measurement and benchmarking. There is a need for studies that attempt to measure and benchmark upstream, leading or developmental aspects of organizations. Therefore, the aim of this paper is twofold. The first is to conduct an in-depth case analysis of lead performance measurement and benchmarking leading to the further development of a conceptual model derived from the extant literature and initial survey data. The second is to outline future research agendas that could further develop the framework and the subject area.

Design/methodology/approach: A multiple case analysis involving repeated in-depth interviews with managers in organisational areas of upstream influence in the case organisations.

Findings: It was found that the effect of external drivers for lead performance measurement and benchmarking was mediated by organisational context factors such as level of progression in business improvement methods. Moreover, the legitimation of the business improvement methods used for this purpose, although typical, had been extended beyond their original purpose with the development of bespoke sets of lead measures.

Practical implications: Examples of methods and lead measures are given that can be used by organizations in developing a programme of lead performance measurement and benchmarking.

Originality/value: There is a paucity of in-depth studies relating to the theory and practice of lead performance measurement and benchmarking in organisations.

MEASUREMENT AND CALCULATION OF ABSOLUTE SINGLE AND MULTIPLE CHARGE EXCHANGE CROSS SECTIONS FOR Feq+ IONS IMPACTING H2O

Charge exchange (CE) plays a fundamental role in the collisions of solar- and stellar-wind ions with lunar and planetary exospheres, comets, and circumstellar clouds. Reported herein are absolute cross sections for single, double, triple, and quadruple CE of Feq+ (q = 5-13) ions with H2O at a collision energy of 7q keV. One measured value of the pentuple CE is also given for Fe9+ ions. An electron cyclotron resonance ion source is used to provide currents of the highly charged Fe ions. Absolute data are derived from knowledge of the target gas pressure, target path length, and incident and charge-exchanged ion currents. Experimental cross sections are compared with new results of the n-electron classical trajectory Monte Carlo approximation. The radiative and non-radiative cascades following electron transfers are approximated using scaled hydrogenic transition probabilities and scaled Auger rates. Also given are estimates of cross sections for single capture, and multiple capture followed by autoionization, as derived from the extended overbarrier model. These estimates are based on new theoretical calculations of the vertical ionization potentials of H2O up to H2O10+.

Rapid and nondestructive measurement of labile Mn, Cu, Zn, Pb and As in DGT by using field portable-XRF

The technique of diffusive gradients in thin films (DGT) is often employed to quantify labile metals in situ; however, it is a challenge to perform the measurements in-field. This study evaluated the capability of field-portable X-ray fluorescence (FP-XRF) to swiftly generate elemental speciation information with DGT. Biologically available metal ions in environmental samples passively preconcentrate in the thin films of DGT devices, providing an ideal and uniform matrix for XRF nondestructive detection. Strong correlation coefficients (r > 0.992 for Mn, Cu, Zn, Pb and As) were obtained for all elements during calibration. The limits of quantitation (LOQ) for the investigated elements of FP-XRF on DGT devices are 2.74 for Mn, 4.89 for Cu, 2.89 for Zn, 2.55 for Pb, and 0.48 for As (unit: µg cm(-2)). When Pb and As co-existed in the solution trials, As did not interfere with Pb detection when using Chelex-DGT. However, there was a significant enhancement of the Pb reading attributed to As when ferrihydrite binding gels were tested, consistent with Fe-oxyhydroxide surfaces absorbing large quantities of As. This study demonstrates the value of the FP-XRF technique to rapidly and nondestructively detect the metals accumulated in DGT devices, providing a new and simple diagnostic tool for on-site environmental monitoring of labile metals/metalloids