Strong visible up-conversion emissions and thermometric applications of Er3+-Yb3+ codoped Al2O3 prepared by the sol-gel method

The Er3+-Yb3+ codoped Al2O3 has been prepared by the sol-gel method using the aluminium isopropoxide [Al(OC3H7)(3)]-derived Al2O3 sols with addition of the erbium nitrate [Er(NO3)(3) center dot 5H(2)O] and ytterbium nitrate [Yb(NO3)(3) center dot 5H(2)O]. The phase structure, including only two crystalline types of doped Al2O3 phases, theta and gamma, was obtained for the 1 mol% Er3+ and 5 mol% Yb3+ codoped Al2O3 at the sintering temperature of 1,273 K. By a 978 nm semiconductor laser diodes excitation, the visible up-conversion emissions centered at about 523, 545, and 660 nm were obtained. The temperature dependence of the green up-conversion emissions was studied over a wide temperature range of 300-825 K, and the reasonable agreement between the calculated temperature by the fluorescence intensity ratio (FIR) theory and the measured temperature proved that Er3+-Yb3+ codoped Al2O3 plays an important role in the application of high temperature sensor.

掺铒碲酸盐玻璃中的浓度猝灭机理研究

测试了掺铒碲酸盐玻璃在不同掺杂浓度下的荧光特性．根据Dexter能量转移理论计算了Er^3+在碲酸盐玻璃中发生浓度猝灭的临界距离R0及Er^3+间相互作用参数CEr-Er，并与其他基质玻璃中CEr-Er数值进行了比较．最后建立了Er^3+基于OH^-作为猝灭中心下碲酸盐玻璃中的浓度猝灭模型．

铒离子浓度对掺Er^3＋碲酸盐玻璃的Judd-Ofelt理论参数的影响

制备了四种不同铒离子掺杂浓度的碲酸盐玻璃，通过测定吸收光谱计算了吸收谱线的振子强度，根据Judd-Ofelt理论计算了不同浓度下Er^3＋离子发光光谱的强度参数Ω（i=2，4，6），计算了自发辐射电偶和磁偶跃迁概率、辐射寿命、荧光分支比等参数，讨论了Er^3＋离子浓度变化对以上这些参数的影响。测试了Er^3＋：^4I13／2→^4I15／2跃迁对应的荧光光谱和Er^3＋：^4I13／2能级荧光寿命。最后应用McCumber理论计算了玻璃中Er^3＋：^4I13／2→^4I15／2跃迁对应的受激发射截面大小

新型掺铒离子氧氟碲酸盐玻璃的光谱性质

探求新的具有优良的热学和光学性能的基质玻璃系统，是获得具有宽带宽和增益平坦的掺Er^3＋光纤放大器（EDFA）的一种有效途径。制备了一种新型氧氟碲酸盐玻璃TeO2-BaF2-LaF3，并对其热学性能和光学性质进行了测试。应用乍得-奥菲尔特（Judd-Ofelt）理论计算了Er^3＋离子的J-O理论参量和荧光寿命r。探讨了氟化物的引入对碲酸盐玻璃结构的改变的影响，并分析了其对玻璃的热学性质和光学性质的影响。实验发现，获得的氧氟碲酸盐玻璃具有优良的热学稳定性（△T=156.6C），宽的荧光半峰全宽（72nm）

掺铒钙铝硅玻璃的光学带隙

玻璃中稀土掺杂的离子的光谱性质受其周围的玻璃结构和在玻璃基质中的分布影响很大。利用熔融法制备了组分为9SiO2·26Al2O3·65CaO·1．0Er2O3·0．3Yb2O3和分别加入MgO以及La2O3的掺铒钙铝硅玻璃，并研究了其吸收边和光学带隙。计算得出离子填充比随玻璃的平均摩尔质量的增大而减小，同时利用Judd—Ofelt模型计算出该玻璃体系的Ω2，Ω4和Ω6参数，并进行了分析。随着MgO或La2O3的加入，吸收边向短波长移动，光学带隙增大，同时Ω2和Ω6值也增大。对ln（α）和hω的曲线进行线性拟

掺铒碲-钨-钠玻璃基质的光谱性质研究

制备了用于离子交换法制备光波导器件的掺铒碲-钨-钠玻璃基质。应用扎得-奥菲而特(Judd—Ofelt)理论计算了玻璃样品的三个强度参量，由强度参量计算了Er^3+离子的自发跃迁几率、荧光分支比等光谱参量；应用麦克库玻(McCumber)理论，计算了Er^3+离子在1．5μm的受激发射截面，荧光测试发现Er^3+离子的荧光半峰全宽可达65nm。比较了Er^3+离子在不同玻璃基质中的光谱特性。结果表明，Er^3+离子在碲-钨-钠玻璃中具有较高的受激发射截面和较宽的荧光半峰全宽，可以用于宽带光波导器件的制备。

Cr^3＋，Yb^3＋，Er^3＋共掺磷酸盐铒玻璃转镜调Q激光性质研究

研究了Cr^3＋，Yb^3＋，Er^3＋共掺磷酸盐铒玻璃转镜调Q激光性质．三种Er2O3掺杂浓度的激光实验结果表明，在Er2O3名义掺杂浓度为0．5wt％时，玻璃的综合激光性质最好，重复频率为0．1Hz时，它的激光阈值功率为14．5mJ，最大输出能量为9．6mJ，斜率效率为0．55％．在同种实验条件下，比较了Cr14和Kigre公司生产的QE-7S激光性质参数，实验表明，前者激光阈值功率稍低，而后者的斜率效率和最大输出功率略高．

掺铒碲酸盐玻璃的热力学稳定性和光谱性质的研究

分析了掺Er^3+碲酸盐玻璃的热力学稳定性能，研究了掺Er^3+碲酸盐玻璃的吸收和荧光光谱性质；应用Judd-Ofelt理论计算了碲酸盐玻璃中Er^3+离子的强度参数Ω(Ω2=4．79×10^-20cm^2,Ω4=1．52×10^-20cm^2，Ω6=0．66×10^-20cm^2)，计算了离子的自发跃迁几率，荧光分支比；应用McCumber理论计算了Er^3+的受激发射截面(σe=10．40×10^-21cm^2)、Er^3+离子^4I13／2→^4I15／2发射谱的荧光半高宽(FWHM=65．5nm)

一种新型掺铒碲酸盐玻璃的光谱性质研究

研究了一种新型掺Er^3+碲酸盐玻璃的光谱性质；应用Judd-Ofelt理论计算了碲酸盐玻璃中Er^3+离子的强度参数Ω(Ω2=4．79×10^-20cm^2，Ω4=1．52×10^-20cm^2，Ω6=0．66×10^-20cm^2)，计算了离子的自发跃迁概率，荧光分支比；应用McCumber理论计算了Er^3+的受激发射截面(σe=10．40×10^-21cm^2)，Er^3+离子^4I13/2→^4I15/2发射谱的荧光半高宽(FWHM=65．5nm)及各能级的荧光寿命(^4I13/2能级为τrad

上转换效应对Er3+-Yb3+共掺磷酸盐玻璃被动调Q 激光输出的影响

To study the effects of upconversion in Erbium, a set of rate equations that simulates the performance of the passively Q-switched Er:Yb:glass laser with a Co²⁺:MgAl2O4 saturable absorber was set up. The dynamics of the Er³⁺ excited state and the effect of upconversion on the passively Q-switched laser are obtained through numerical simulation of the model. It is found that the impact ratios of upconversion effect on the peak power of the passively Q-switched laser pluse and the repetition rate are both decreased with the increase of pump power.

Gain characteristics of Er3+-doped phosphate glass fibres

An erbium-doped phosphate glass fibre has been drawn by the rod-in-tube technique in our laboratory. The gain for the Er3+-doped phosphate glass fibre with different pump powers and with different input signal wavelengths is investigated. The 2.2-cm-long fibre, pumped by a single-mode 980-nm fibre-pigtailed laser diode, can provide a net gain per unit length greater than 1.8dB/cm. The pump threshold is about 50 mW at the wavelength of 1534 nm, and below 70 mW at 1550 nm. The gain linewidth of the Er3+-doped phosphate glass fibre is greater than 34 nm and can cover the C band in optical communication networks.

Host dependent frequency upconversion of Er3+-doped oxyfluoride germanate glass

Er3+-doped oxyfluoride germanate glasses have been synthesized by the conventional melting and quenching method. The Judd-Ofelt intensity parameters were calculated based on the Judd-Ofelt theory and absorption spectra measurements. With the substitution of PbF2 for PbO, the Omega(2) parameter decreases, while the Omega(6) parameter increases. These change trends indicate that fluoride anions come to coordinate erbium cations and the covalency of the Er-O bond decreases. Structural and thermal stability properties were obtained by Raman spectra and differential thermal analysis, indicating that PbF2 plays an important role in the formation of glass network and has an important influence on the maximum phonon energy and thermal stability of host glasses. Intense green and red emissions centered at 525, 546, and 657 nm, corresponding to the transitions H-2(11/2) -> I-4(15/2), S-4(3/2) -> I-4(15/2), and F-4(9/2) -> I-4(15/2), respectively, were simultaneously observed at room temperature. With increasing PbF2 content, the intensity of red (657nm) emissions increases significantly, while that of the green (525 and 546nm) emission increases slightly. The results indicate that PbF, has more influence on the red (657nm) emission than the green (525 and 546nm) emissions in oxyfluoride germanate glasses. The possible upconversion luminescence mechanisms have also been estimated and discussed. (c) 2005 Elsevier B.V. All rights reserved.

Effect of hydroxyl groups on nonradiative decay of Er3+: I-4(13/2)-> I-4(15/2) transition in zinc tellurite glasses

A series of zinc tellurite glasses of 75TeO(2)-20ZnO-(5-x)La2O3-xEr(2)O(3) (x=0.02, 0.05, and 0.1 mol%) with the different hydroxl groups were prepared by the conventional melt-quenching method. Infrared spectra were measured in order to estimate the exact content of OH- groups in samples. The observed increase of the fluorescence lifetime with the oxygen bubbling time has been related to the reduction in the OH- content concentration as evidenced by IR transmission spectra. Various nonradiative decay rates from I-4(13/2) of Er3+ with. the change of OH content were determined from the fluorescence lifetime and radiative decay rates were calculated on the basis of Judd-Ofelt theory. (c) 2005 Elsevier B.V. All rights reserved.

The spectroscopic properties of Er3(+)-doped TeO2-Nb2O5 glasses with high mechanical strength performance

(100 - x)TeO2 - xNb(2)O(5) (x=5-20) mobic tellurite glasses doped with 0.5 mol.% Er2O3 were synthesized, and their thermal, mechanical, and spectroscopic properties were measured and compared to the properties of the typical 75TeO(2)-20ZnO-5Na(2)O (TZN) tellurite glass. The refractive index (n(d)), density (p), and glass transition temperature (T-g) of bulk glasses increase with the Nb2O5 content. The Vickers microhardness (H-v) of bulk glass in niobic tellurite glasses also increases with the Nb2O5 content. The values (2.5-3.2 GPa) of H, in the niobic tellurite glasses are 47-88% larger than that (1.7 GPa) in TZN glass. The effect of Nb2O5 content on absorption spectra, the Judd-Ofelt parameters Omega(t) (t = 2, 4, 6), fluorescence spectra and the lifetimes of Er3+ :I-13/2 level were also investigated, and the stimulated emission crosssection was calculated from McCumber theory. With increasing Nb2O5 content in the glass composition, the Omega(t) (t = 2, 4, 6) parameters, fluorescence full width at half maximum (FWHM) Of I-13/2 of Er3+ increase, while the I-4(13/2) lifetimes of Er3+ decreases. Compared with TZN glass, the gain bandwidth properties of Er3+-doped TeO2-Nb2O5 glass is much larger than in tellurite glass based TeO2-ZnO-Na2O system, bismush-based glass, germanate, and silicate glasses, which indicates that TeO2-Nb2O5 glasses are better choice as a practical available host material for broadband Er3+-doped amplifier. (c) 2005 Elsevier B.V. All rights reserved.

Fabrication and emission properties of Er3+/Yb3+ codoped tellurite glass fiber for broadband optical amplification

Tellurite glass is proposed as a host for broadband erbium-doped fiber amplifiers because of their excellent optical and chemical properties. A new single mode Er3+/Yb3+ codoped tellurite fiber with D-shape cladding geometry is fabricated in this work. When pumped at 980 nm, a broad erbium amplified spontaneous emission (ASE) nearly 100 nm in the wavelength range of 1450-1650 ran around 1.53 mu m is observed. It was found that the emission spectrum from erbium in tellurite glass fibers is almost twice as broad as the corresponding spectrum in tellurite bulk glass. The changes in ASE with regard to fiber lengths and pumping power were measured and discussed. The output of about 2.3 mW from Er3+/Yb3+ codoped tellurite fiber ASE source is obtained under the pump power of 700 mW. The broad 1.53 mu m emission of Er3+ in Er3+/Yb3+ codoped tellurite glass fiber can be used as host material for potential broadband optical amplifier and tunable fiber lasers. (c) 2005 Elsevier B.V. All rights reserved.