Role of carbon nanotube dispersion in fracture toughening of plasma sprayed aluminum oxide-carbon nanotube nanocomposite coating

Aluminum oxide (Al2O3, or alumina) is a conventional ceramic known for applications such as wear resistant coatings, thermal liners, heaters, crucibles, dielectric systems, etc. However applications of Al 2O3 are limited owing to its inherent brittleness. Due to its excellent mechanical properties and bending strength, carbon nanotubes (CNT) is an ideal reinforcement for Al2O3 matrix to improve its fracture toughness. The role of CNT dispersion in the fracture toughening of the plasma sprayed Al2O3-CNT nanocomposite coating is discussed in the current work. Pretreatment of powder feedstock is required for dispersing CNTs in the matrix. Four coatings namely spray dried Al2O 3 (A-SD), Al2O3 blended with 4wt.% CNT (A4C-B), composite spray dried Al2O3-4wt.% CNT (A4C-SD) and composite spray dried A1203-8wt.% CNT (A8C-SD), are synthesized by plasma spraying. Owing to extreme temperatures and velocities involved in the plasma spraying of ceramics, retention of CNTs in the resulting coatings necessitates optimizing plasma processing parameters using an inflight particle diagnostic sensor. A bimodal microstructure was obtained in the matrix that consists of fully melted and resolidified structure and solid state sintered structure. CNTs are retained both in the fully melted region and solid-state sintered regions of processed coatings. Fracture toughness of A-SD, A4C-B, A4C-SD and A8C-SD coatings was 3.22, 3.86, 4.60 and 5.04 MPa m1/2 respectively. This affirms the improvement of fracture toughness from 20% (in A4C-B coating) to 43% (in A4C-SD coating) when compared to the A-SD coating because of the CNT dispersion. Fracture toughness improvement from 43% (in A4C-SD) to 57% (in A8C-SD) coating is evinced because of the CNT content. Reinforcement by CNTs is described by its bridging, anchoring, hook formation, impact alignment, fusion with splat, and mesh formation. The Al2O3/CNT interface is critical in assisting the stress transfer and utilizing excellent mechanical properties of CNTs. Mathematical and computational modeling using ab-initio principle is applied to understand the wetting behavior at the Al2O 3/CNT interface. Contrasting storage modulus was obtained by nanoindentation (∼210, 250, 250-350 and 325-420 GPa in A-SD, A4C-B, A4C-SD, and A8C-SD coatings respectively) depicting the toughening associated with CNT content and dispersion.

Specific binding of the mammalian high mobility group protein AT-hook 2 to the minor groove of AT -rich DNAs: Thermodynamic and specificity studies

The mammalian high mobility group protein AT-hook 2 (HMGA2) is a small transcriptional factor involved in cell development and oncogenesis. It contains three "AT-hook" DNA binding domains, which specifically recognize the minor groove of AT-rich DNA sequences. It also has an acidic C-terminal motif. Previous studies showed that HMGA2 mediates all its biological effects through interactions with AT-rich DNA sequences in the promoter regions. In this dissertation, I used a variety of biochemical and biophysical methods to examine the physical properties of HMGA2 and to further investigate HMGA2's interactions with AT-rich DNA sequences. The following are three avenues perused in this study: (1) due to the asymmetrical charge distribution of HMGA2, I have developed a rapid procedure to purify HMGA2 in the milligram range. Preparation of large amounts of HMGA2 makes biophysical studies possible; (2) Since HMGA2 binds to different AT-rich sequences in the promoter regions, I used a combination of isothermal titration calorimetry (ITC) and DNA UV melting experiment to characterize interactions of HMGA2 with poly(dA-dT) 2 and poly(dA)poly(dT). My results demonstrated that (i) each HMGA2 molecule binds to 15 AT bp; (ii) HMGA2 binds to both AT DNAs with very high affinity. However, the binding reaction of HMGA2 to poly(dA-dT) 2 is enthalpy-driven and the binding reaction of HMGA2 with poly(dA)poly(dT) is entropy-driven; (iii) the binding reactions are strongly depended on salt concentrations; (3) Previous studies showed that HMGA2 may have sequence specificity. In this study, I used a PCR-based SELEX procedure to examine the DNA binding specificity of HMGA2. Two consensus sequences for HMGA2 have been identified: 5'-ATATTCGCGAWWATT-3' and 5'-ATATTGCGCAWWATT-3', where W represents A or T. These consensus sequences have a unique feature: the first five base pairs are AT-rich, the middle four to five base pairs are GC-rich, and the last five to six base pairs are AT-rich. All three segments are critical for high affinity binding. Replacing either one of the AT-rich sequences to a non-AT-rich sequence causes at least 100-fold decrease in the binding affinity. Intriguingly, if the GC-segment is substituted by an AT-rich segment, the binding affinity of HMGA2 is reduced approximately 5-fold. Identification of the consensus sequences for HMGA2 represents an important step towards finding its binding sites within the genome.

Role of carbon nanotube dispersion in fracture toughening of plasma sprayed aluminum oxide - carbon nanotube nanocomposite coating

Aluminum oxide (A1203, or alumina) is a conventional ceramic known for applications such as wear resistant coatings, thermal liners, heaters, crucibles, dielectric systems, etc. However applications of A1203 are limited owing to its inherent brittleness. Due to its excellent mechanical properties and bending strength, carbon nanotubes (CNT) is an ideal reinforcement for A1203 matrix to improve its fracture toughness. The role of CNT dispersion in the fracture toughening of the plasma sprayed A1203-CNT nanocomposite coating is discussed in the current work. Pretreatment of powder feedstock is required for dispersing CNTs in the matrix. Four coatings namely spray dried A1203 (A-SD), A1203 blended with 4wt.% CNT (A4C-B), composite spray dried A1203-4wt.% CNT (A4C-SD) and composite spray dried A1203-8wt.% CNT (A8CSD), are synthesized by plasma spraying. Owing to extreme temperatures and velocities involved in the plasma spraying of ceramics, retention of CNTs in the resulting coatings necessitates optimizing plasma processing parameters using an inflight particle diagnostic sensor. A bimodal microstructure was obtained in the matrix that consists of fully melted and resolidified structure and solid state sintered structure. CNTs are retained both in the fully melted region and solid-state sintered regions of processed coatings. Fracture toughness of A-SD, A4C-B, A4C-SD and A8C-SD coatings was 3.22, 3.86, 4.60 and 5.04 MPa m1/2 respectively. This affirms the improvement of fracture toughness from 20 % (in A4C-B coating) to 43% (in A4C-SD coating) when compared to the A-SD coating because of the CNT dispersion. Fracture toughness improvement from 43 % (in A4C-SD) to 57% (in A8C-SD) coating is evinced because of the CNT content. Reinforcement by CNTs is described by its bridging, anchoring, hook formation, impact alignment, fusion with splat, and mesh formation. The A1203/CNT interface is critical in assisting the stress transfer and utilizing excellent mechanical properties of CNTs. Mathematical and computational modeling using ab-initio principle is applied to understand the wetting behavior at the A1203/CNTinterface. Contrasting storage modulus was obtained by nanoindentation (~ 210, 250, 250-350 and 325-420 GPa in A-SD, A4C-B, A4C-SD, and A8C-SD coatings respectively) depicting the toughening associated with CNT content and dispersion.

Age model and pollen analysis from site GIK16867 in the northern Angola Basin

Sporomorphs and dinoflagellate cysts from site GIK16867 in the northern Angola Basin record the vegetation history of the West African forest during the last 700 ka in relation to changes in salinity and productivity of the eastern Gulf of Guinea. During most cool and cold periods, the Afromontane forest, rather than the open grass-rich dry forest, expanded to lower altitudes partly replacing the lowland rain forest of the borderlands east of the Gulf of Guinea. Except in Stage 3, when oceanic productivity was high during a period of decreased atmospheric circulation, high oceanic productivity is correlated to strong winds. The response of marine productivity in the course of a climatic cycle, however, is earlier than that of wind vigour and makes wind-stress-induced oceanic upwelling in the area less likely. Monsoon variation is well illustrated by the pollen record of increased lowland rain forest that is paired to the dinoflagellate cyst record of decreased salinity forced by increased precipitation and run-off.

In-situ formation of solidified hydrogen thin-membrane targets using a pulse tube cryocooler

An account is given of the Central Laser Facility's work to produce a cryogenic hydrogen targetry system using a pulse tube cryocooler. Due to the increasing demand for low Z thin laser targets, CLF (in collaboration with TUD) have been developing a system which allows the production of solid hydrogen membranes by engineering a design which can achieve this remotely; enabling the gas injection, condensation and solidification of hydrogen without compromising the vacuum of the target chamber. A dynamic sealing mechanism was integrated which allows targets to be grown and then remotely exposed to open vacuum for laser interaction. Further research was conducted on the survivability of the cryogenic targets which concluded that a warm gas effect causes temperature spiking when exposing the solidified hydrogen to the outer vacuum. This effect was shown to be mitigated by improving the pumping capacity of the environment and reducing the minimum temperature obtainable on the target mount. This was achieved by developing a two-stage radiation shield encased with superinsulating blanketing; reducing the base temperature from 14 0.5 K to 7.2 0.2 K about the coldhead as well as improving temperature control stability following the installation of a high-performance temperature controller and sensor apparatus. The system was delivered experimentally and in July 2014 the first laser shots were taken upon hydrogen targets in the Vulcan TAP facility.

A Machine Learning Analysis of Twitter Sentiment to the Sandy Hook Shootings

Gun related violence is a complex issue and accounts for a large proportion of violent incidents. In the research reported in this paper, we set out to investigate the pro-gun and anti-gun sentiments expressed on a social media platform, namely Twitter, in response to the 2012 Sandy Hook Elementary School shooting in Connecticut, USA. Machine learning techniques are applied to classify a data corpus of over 700,000 tweets. The sentiments are captured using a public sentiment score that considers the volume of tweets as well as population. A web-based interactive tool is developed to visualise the sentiments and is available at this http://www.gunsontwitter.com. The key findings from this research are: (i) There are elevated rates of both pro-gun and anti-gun sentiments on the day of the shooting. Surprisingly, the pro-gun sentiment remains high for a number of days following the event but the anti-gun sentiment quickly falls to pre-event levels. (ii) There is a different public response from each state, with the highest pro-gun sentiment not coming from those with highest gun ownership levels but rather from California, Texas and New York.

Analyse von Schüler-Versuchsprotokollen beim eigenständigen Experimentieren am Beispiel des Hook'schen Gesetzes

Mit der Einführung der Bildungsstandards für den mittleren Schulabschluss im Fach Physik ist vor allem der Prozess der Erkenntnisgewinnung stärker in den Mittelpunkt didaktischer und unterrichtlicher Arbeit gerückt. Damit erhält insbesondere das Experiment eine noch größere Rolle für den naturwissenschaftlichen Unterricht als ihm bereits vor der Einführung zukam. Im erkenntnistheoretischen Sinn gilt es neben der Entwicklung von Fragestellungen als eine der zentralen naturwissenschaftlichen Arbeitsweisen in der Physik. Ein besonderes Potential für den Physikunterricht bietet in diesem Zusammenhang das Schülerexperiment, dem trotz umstrittener Wirksamkeit zahlreiche Vorzüge zugeschrieben werden können. Neben der Förderung von praktischen experimentellen Fähigkeiten zählen dazu vor allem die Einführung in naturwissenschaftliche Denk- und Arbeitsprozesse und die Steigerung der Motivation bei den Lernenden. Um als Lehrperson konkret mit den auftretenden Problemen im Unterricht umgehen zu können und die Schülerinnen und Schüler angesichts wachsender Heterogenität individuell fördern zu können, ist es jedoch unerlässlich, über die Bandbreite der Schwierigkeiten Bescheid zu wissen und diese wiederum bei der Unterrichtsplanung zu berücksichtigen. Daher sollen im Rahmen dieser Arbeit Schüler-Versuchsprotokolle im Hinblick auf mögliche Schwierigkeiten der Lernenden analysiert werden. Die auszuwertenden Protokolle sind bereits im Rahmen des DiSiE-Projektes der Universität Kassel, das sich mit der Diagnose von Schülerschwierigkeiten beim eigenständigen Experimentieren beschäftigt, entstanden und wurden von Schülerinnen und Schüler während der Bearbeitung einer Experimentieraufgabe zum Hook’schen Gesetz angefertigt.

Map of the bays, harbors, and rivers around New York : showing the channels, soundings, lighthouses, buoys &c., and the complete topography of the surrounding country : including Hempstead, Sandy-Hook, South-Amboy, Newark, Yonkers, N. Rochelle & Glen Cove /

Relief shown by hachures. Depths shown by contours and soundings.

Changing family models in Spain: the impact of the sociodemographic factors

Abstract During the last few decades, there has been an increasing international recognition of the studies related to the analysis of the family models change, the focus being the determinants of the female employment and the problems related to the work family balance (Lewis, 2001; Petit & Hook, 2005Saraceno, Crompton & Lyonette, 20062008; Pfau-Effinger, 2012). The majority of these studies have been focused on the analysis of the work-family balance problems as well as the effectiveness of the family and gender policies in order to encourage female employment (Korpi et al., 2013). In Spain, special attention has been given to the family policies implemented, the employability of women and on the role of the father in the family (Flaquer et al., 2015; Meil, 2015); however, there has been far less emphasis on the analysis of the family cultural models (González and Jurado, 2012; Crespi and Moreno, 2016). The purpose of this paper is to present some of the first results on the influence of the socio-demographic factors on the expectations and attitudes about the family models. This study offers an analytical reflection upon the foundation of the determinants of the family ambivalence in Spain from the cultural and the institutional dimension. This study shows the Spanish family models of preferences following the Pfau-Effinger (2004) classification of the famiy living arrangements. The reason for this study is twofold; on the one hand, there is confirmed the scarcity of studies that have focused their attention on this objective in Spain; on the other hand, the studies carried out in the international context have confirmed the analytical effectiveness of researching on the attitude and value changes to explain the meaning and trends of the family changes. There is also presented some preliminary results that have been obtained from the multinomial analysis related to the influence of the socio-demographic factors on the family model chosen by the individuals in Spain (father and mother working full time; mother part-time father full-time; mother not at work father full-time; mother and father part-time). 3 The database used has been the International Social Survey Programme: Family and Changing Gender Roles IV- ISSP 2012-. Spain is the only country of South Europe that has participated in the survey. For this reason it has been considered as a representative case study.

Effect of light-sticks and electralunie attractors on surface-longline catches of swordfish (Xiphias gladius, Linnaeus, 1959) in the southwest equatorial Atlantic

Two experimental fishing trials were carried out off the coast of Pernambuco, Brazil, in 1999 and 2001, using a small artisanal longliner. In experiment 1, six-hook baskets with three chemical light-sticks on alternating hooks had significantly higher catch rates than those with zero or with a light-stick on every hook, with most swordfish accounted for by hooks with light-sticks. Analysis of the data from experiment 2 showed no significant difference between electralume attractors, consisting of AA lithium batteries protected by a solid cover and light-sticks that produce a fluorescent light when two chemical products are mixed. Significant differences were detected in mean CPUE by size class, with most swordfish belonging to class 'b' (125-170 cm lower jaw to fork length (LJFL)). No differences, however, were found for swordfish catches in classes 'a' (< 125 cm LJFL) and V, and no evidence was found of interaction between the two factors (attractor and size class). Although there was no significant difference between the total length-frequency distributions of swordfish caught with light-sticks and electralume attractors, signibcant differences were found for fish smaller than 125 cm LJFL, with electralume catches consisting of smaller swordfish than those of gear using light-sticks. (c) 2004 Elsevier B.V. All rights reserved.

Quantifying the roles of competing static gears: comparative selectivity of longlines and monofilament gill nets in a multi-species fishery of the Algarve (southern Portugal)

Fishing trials with monofilament gill nets and longlines using small hooks were carried out in Algarve waters (southern Portugal) over a one-year period. Four hook sizes of "Mustad" brand, round bent, flatted sea hooks (Quality 2316 DT, numbers 15, 13, 12 and 11) and four mesh sizes of 25, 30, 35 and 40 mm (bar length) monofilament gill nets were used. Commercially valuable sea breams dominated the longline catches while small pelagics were relatively more important in the gill nets. Significant differences in the catch size frequency distributions of the two gears were found for all the most important species caught by both gears (Boops boops, Diplodus bellottii, Diplodus vulgaris, Pagellus acarne, Pagellus erythrinus, Spondyiosoma cantharus, Scomber japonicus and Scorpaena notata), with longlines catching larger fish and a wider size range than nets. Whereas longline catch size frequency distributions for most species for the different hook sizes were generally highly overlapped, suggesting little or no differences in size selectivity, gill net catch size frequency distributions clearly showed size selection. A variety of models were fitted to the gill net and hook data using the SELECT method, while the parameters of the logistic model were estimated by maximum likelihood for the longline data. The bi-normal model gave the best fits for most of the species caught with gill nets, while the logistic model adequately described hook selectivity. The results of this study show that the two static gears compete for many of the same species and have different impacts in terms of catch composition and size selectivity. This information will I;e useful for the improved management of these small-scale fisheries in which many different gears compete for scarce resources.

Reduction of elasmobranch by-catch in the hake semipelagic near-bottom longline fishery in the Algarve (Southern Portugal)

Elasmobranch fish, particularly deep-sea sharks, are the most important component of the by-catch of the hake semipelagic near-bottom 'pedra-e-bola' longline fishery in the Algarve (South Portugal) and most of these fish are discarded. The effects of the removal of the lower hooks were evaluated, in terms of target and by-catch reductions, by quantifying the catches of each hook relative to the distance from the bottom. The analysis showed that most European hake (Merluccius merluccius), the target species of this fishery, were caught in the middle range of the hooks, with very few individuals caught near the bottom, whereas for sharks the situation was the opposite, with most hooked near the bottom. The removal of the lower three pairs of hooks would result in a small reduction in the catch of the target species, but a much more significant reduction in elasmobranch by-catch. In the specific case of the blackmouth catshark (Galeus melastomus), discard mortality would be further minimized due to the fact that the lower hooks capture significantly smaller animals that are always discarded compared with hooks that are more distant from the bottom.

Short-term hooking mortality of three marine fish species (Sparidae) caught by recreational angling in the south Portugal

Short-term hooking mortality was evaluated for three sparid species [Diplodus vulgaris (Geoffroy Saint-Hilaire), Spar-us aurata L. and Spondyliosoma cantharus (L.)] in the Algarve, south Portugal. Fishes were caught from the shore during October 2009 at a fish farm reservoir (Ria Formosa), using three different hook sizes. The relationships between hooking mortality and seven independent variables were analyzed using logistic regression models. In all,384 fishes representing the three target species were caught during the angling sessions. The most caught species was S. cantharus (n = 181; 100% undersized), followed by S. aurata (n = 137; 89% undersized) and D. vulgaris (n = 66; 97% undersized). Mortalities ranged between 0% for D. vulgaris and 12% for S. aurata (S. cantharus, 3%). For S. aurora, anatomical hooking location was the main predictor of mortality, with 63% of the fishes that died being deeply hooked. Our results support the current mandatory practices of releasing undersized fish for the studied species, given the low post-release mortality rates observed. (C) 2010 Elsevier B.V. All rights reserved.

Species and size selectivity in a Portuguese multispecies artisanal long-line fishery

The species and size selectivity of long-lines using small hooks were studied off the south coast of Portugal using ''Mustad'' brand round bent, flatted sea hooks (Quality 2316 DT) numbers 15, 13, and 11 baited with razor shell clam (Ei-isis siliqua). Hook numbers 13 and 11 are 49 and 109% larger respectively than number 15 hooks in terms of overall size (maximum width x maximum length). A total of 39 900 hooks were fished in 45 sets and 35 species of fish and cephalopods were caught. As a group, 13 species of sea breams (Sparidae) dominated the catch by numbers (58%) and weight (73%). Six species of sea breams, along with the greater weever fish (Trachinus draco) accounted for 81% of the total catch by weight, with the common or white sea bream (Diplodus sargus) bring the most important (29%). Catch size distributions by hook size were, in general, highly overlapped for all species and hook size had little apparent effect on minimum size at capture. All hooks caught a wide range of sizes per species, but the catch rate (number of fish per 100 hooks) was significantly lower for the largest hook. Except for the black sea bream (Spondyliosoma cantharus), capture of illegally sized or immature fish was minimal. Small increases in average size with hook size were evident for four species: Diplodus sargus, D. vulgaris, Lithognathus mormyrus and Serranus cabrilla. No differences in size selectivity were detected for Boops boops, D. annularis, Spondyliosoma cantharus and Trachinus draco. A skew-normal model adequately described differences in size selectivity in five of six species. (C) 1996 International Council for the Exploration of the Sea

Species and size selectivity in a 'red' sea bream longline 'metier' in the Algarve (southern Portugal)

A longline 'metier' using small hooks for 'red' sea breams (Pagellus acarne and Pagellus erythrinus) in the Algarve (south of Portugal) was studied. Experimental longlining was carried out with three sizes of "Mustad" round bend, flatted, spade end Quality 2316 DT hooks (numbers 11, 13 and 15) and two types of bait: razor shell (Ensis siliqua) and mud shrimp (Upogebia pusilla). A total of 3 328 fish and at least 36 species were caught with 33 600 hooks fished in 28 longline sets. Five species of sea breams (Sparidae) accounted for 79% of the catch: Pagellus acarne, Pagellus erythrinus, Diplodus vulgaris, Spondyliosoma cantharus, and Boops boops. High catch rates of 20-30 fish per 100 hooks were made in a number of 1 200 hook longline sets, with total catch weights of 40 to more than 60 kg per set. In general, the smallest hook (number 15) had the highest catch rate. Bait type did not significantly affect the catch size distributions. Although more fish were caught with the razor shell bait, higher catch rates of 'red' sea breams were obtained with mud shrimp. Catch rates were also affected by the location of the fishing grounds and the time of the set, with the highest catch rates obtained when the longline was set within two hours before sunrise. A wide size range was caught for each species, with highly overlapped catch size frequency distributions for the three hook sizes used. Except for Spondyliosoma cantharus, few illegal-sized fish were caught, even with the smallest hook. The logistic model fitted by maximum likelihood was used to describe hook selectivity for Diplodus vulgaris, Pagellus acarne, Pagellus erythrinus, and Spondyliosoma cantharus. (C) Ifremer-Elsevier, Paris.