Wrought aluminum-nickel alloys for high strength-high conductivity applications

Aluminum-Nickel alloys ranging from 0.06 pct to 6.1 pct (by wt) Ni have been developed for high strength-high conductivity applications. These alloys were produced by solidification in a permanent mold followed by homogenization, hot extrusion or hot rolling and cold drawing to wire form. This sequence of fabrication a) led to the production of fine fibrous dispersoids of NiAl3 as part of the Al-NiAl3 eutectic during the initial casting operation, b) permitted the retention of fine fibrous dispersiods of NiAl3 produced during casting without any significant coarsening during processing and c) led to uniform dispersion and general alignment of these fibrous dispersoids along a given direction in the product without any measurable fiber-matrix separation, extensive fiber-fragmentation or crack production in the matrix. These alloys can be processed to wire form as easily as aluminum and when processed by the above sequence, possess very attractive combination of high strength-high electrical conductivity. Tensile strengths range from 173 N/mm2 (at 0.6 pct Ni) to 241 N/mm2 (at 6.1 pct Ni) in combination with corresponding conductivity values between 62 pct IACS and 55.5 pct IACS. The wires also possess attractive yield strength; for instance, the 0.2 pct off-set strength of Al-6.1 pct Ni wire is 213 N/mm2. Using simple composite rules, the estimated strength and the conductivity of NiAl3 fibers were found to be 1380 N/mm2 and 18 pct IACS respectively, in these wires.

Dental Service Utilization, Dental Health Production and Equity in Dental Care: the Finnish Experience

This thesis is grounded on four articles. Article I generally examines the factors affecting dental service utilization. Article II studies the factors associated with sector-specific utilization among young adults entitled to age-based subsidized dental care. Article III explores the determinants of dental ill-health as measured by the occurrence of caries and the relationship between dental ill-health and dental care use. Article IV measures and explains income-related inequality in utilization. Data employed were from the 1996 Finnish Health Care Survey (I, II, IV) and the 1997 follow-up study included in the longitudinal study of the Northern Finland 1966 Birth Cohort (III). Utilization is considered as a multi-stage decision-making process and measured as the number of visits to the dentist. Modified count data models and concentration and horizontal equity indices were applied. Dentist s recall appeared very efficient at stimulating individuals to seek care. Dental pain, recall, and the low number of missing teeth positively affected utilization. Public subvention for dental care did not seem to statistically increase utilization. Among young adults, a perception of insufficient public service availability and recall were positively associated with the choice of a private dentist, whereas income and dentist density were positively associated with the number of visits to private dentists. Among cohort females, factors increasing caries were body mass index and intake of alcohol, sugar, and soft drinks and those reducing caries were birth weight and adolescent school achievement. Among cohort males, caries was positively related to the metropolitan residence and negatively related to healthy diet and education. Smoking increased caries, whereas regular teeth brushing, regular dental attendance and dental care use decreased caries. We found equity in young adults utilization but pro-rich inequity in the total number of visits to all dentists and in the probability of visiting a dentist for the whole sample. We observed inequity in the total number of visits to the dentist and in the probability of visiting a dentist, being pro-poor for public care but pro-rich for private care. The findings suggest that to enhance equal access to and use of dental care across population and income groups, attention should focus on supply factors and incentives to encourage people to contact dentists more often. Lowering co-payments and service fees and improving public availability would likely increase service use in both sectors. To attain favorable oral health, appropriate policies aimed at improving dental health education and reducing the detrimental effects of common risk factors on dental health should be strengthened. Providing equal access with respect to need for all people ought to take account of the segmentation of the service system, with its two parallel delivery systems and different supplier incentives to patients and dentists.

Sostdc1 Plays an Essential Role in Mammalian Tooth Patterning : Insight into the Rodent Dental Evolution

This thesis work focuses on the role of TGF-beta family antagonists during the development of mouse dentition. Tooth develops through an interaction between the dental epithelium and underlying neural crest derived mesenchyme. The reciprocal signaling between these tissues is mediated by soluble signaling molecules and the balance between activatory and inhibitory signals appears to be essential for the pattern formation. We showed the importance of Sostdc1 in the regulation of tooth shape and number. The absence of Sostdc1 altered the molar cusp patterning and led to supernumerary tooth formation both in the molar and incisor region. We showed that initially, Sostdc1 expression is in the mesenchyme, suggesting that dental mesenchyme may limit supernumerary tooth induction. We tested this in wild-type incisors by minimizing the amount of mesenchymal tissue surrounding the incisor tooth germs prior to culture in vitro. The cultured teeth phenocopied the extra incisor phenotype of the Sostdc1-deficient mice. Furthermore, we showed that minimizing the amount of dental mesenchyme in cultured Sostdc1-deficient incisors caused the formation of additional de novo incisors that resembled the successional incisor development resulting from activated Wnt signaling. Sostdc1 seemed to be able to inhibit both mesenchymal BMP4 and epithelial canonical Wnt signaling, which thus allows Sostdc1 to restrict the enamel knot size and regulate the tooth shape and number. Our work emphasizes the dual role for the tooth mesenchyme as a suppressor as well as an activator during tooth development. We found that the placode, forming the thick mouse incisor, is prone to disintegration during initiation of tooth development. The balance between two mesenchymal TGF-beta family signals, BMP4 and Activin is essential in this regulation. The inhibition of BMP4 or increase in Activin signaling led to the splitting of the large incisor placode into two smaller placodes resulting in thin incisors. These two signals appeared to have different effects on tooth epithelium and the analysis of the double null mutant mice lacking Sostdc1 and Follistatin indicated that these TGF-beta inhibitors regulate the mutual balance of BMP and Activin in vivo. In addition, this work provides an alternative explanation for the issue of incisor identity published in Science by Tucker et al. in 1998 and proposes that the molar like morphology that can be obtained by inhibiting BMP signaling is due to partial splitting of the incisor placodes and not due to change in tooth identity from the incisor to the molar. This thesis work presents possible molecular mechanisms that may have modified the mouse dental pattern during evolution leading to the typical rodent dentition of modern mouse. The rodent dentition is specialized for gnawing and consists of two large continuously growing incisors and toothless diastema region separating the molars and incisors. The ancestors of rodents had higher number of more slender incisors together with canines and premolars. Additionally, murine rodents, which include the mouse, have lost their ability for tooth replacement. This work has revealed that the inhibitory molecules appear to play a role in the tooth number suppression by delineating the spatial and temporal action of the inductive signals. The results suggest that Sostdc1 plays an essential role in several stages of tooth development through the regulation of both the BMP and Wnt pathway. The work shows a dormant sequential tooth forming potential present in wild type mouse incisor region and gives a new perspective on tooth suppression by dental mesenchyme. It reveals as well a novel mechanism to create a large mouse incisor through the regulation of mesenchymal balance between inductive and inhibitory signals.

Role of silicon in resisting subsurface plastic deformation in tribology of aluminium-silicon alloys

Silicon particles standing proud on aluminium-silicon alloy surfaces provide protection in tribology. Permanent sinking of such particles into the matrix under load can be deleterious. The mechanical response of the alloy to nano-indentation of single silicon particles embedded in the matrix is explored. A nominal critical pressure required to plastically deform the matrix to permanently embed the particle is determined experimentally. Within a framework suggested by two-dimensional models of plastic response to indentation, a probable correlation is established between the normal mean pressure required to cause permanent sinking of silicon particles and a factor which relates the relevant particle dimensions.

Direct physical evidence for the back-transformation of stress-induced martensite in the vicinity of cracks in pseudoelastic NiTi shape memory alloys

Crack loading and crack extension in pseudoelastic binary NiTi shape memory alloy (SMA) miniature compact tension (CT) specimens with 50.7 at.% Ni (austenitic, pseudoelastic) was investigated using infrared (IR) thermography during in situ loading and unloading. IR thermographic measurements allow for the observation of heat effects associated with the stress-induced transformation of martensite from B2 to BIT during loading and the reverse transformation during unloading. The results are compared with optical images and discussed in terms of the crack growth mechanisms in pseudoelastic NiTi SMAs. Direct experimental evidence is presented which shows that crack growth occurs into a stress-induced martensitic microstructure, which immediately retransforms to austenite in the wake of the crack.

Elastic modulus of Ti-6Al-4V-xB alloys with B up to 0.55 wt.%

An anomalous variation in the experimental elastic modulus, E, of Ti-6Al-4V-xB (with x up to 0.55 wt.%) is reported. Volume fractions and moduli of the constituent phases were measured using microscopy and nanoindentation,respectively. These were used in simple micromechanical models to examine if the E values could be rationalized. Experimental E values higher than the upper bound estimates suggest complex interplay between microstructural modifications, induced by the addition of B, and properties.

A fluctuation-based characterization of athermal phase transitions:Application to shape memory alloys

We employ a fluctuation-based technique to investigate the athermal component associated with martensite phase transition, which is a prototype of temperature-driven structural transformation. Statistically, when the phase transition is purely athermal, we find that the temporal sequence of avalanches under constant drive is insensitive to the drive rate. We have used fluctuations in electrical resistivity or noise in nickel titanium shape memory alloys in three different forms: a thin film exhibiting well-defined transition temperatures,a highly disordered film, and a bulk wire of rectangular cross-section. Noise is studied in the realm of dynamic transition,viz.while the temperature is being ramped, which probes into the kinetics of the transformation at real time scales,and could probably stand out as a promising tool for material testing in various other systems, including nanoscale devices.

On the hardness of shear bands in amorphous alloys

The nanoindentation hardness of individual shear bands in a Zr-based metallic glass was investigated in order to obtain a better understanding of how shear band plasticity is influenced by non-crystalline defects. The results clearly showed that the shear band hardness in both as-cast and structurally relaxed samples is much lower than the respective hardness of undeformed region. Interestingly, inter-band matrix also exhibited lower hardness than undeformed region. The results are discussed in terms of the influence of structural state and the prevailing mechanism of plastic deformation.

Protocol for assessing maternal, environmental and epigenetic risk factors for dental caries in children

Background Expenditure on dental and oral health services in Australia is $3.4 billion AUD annually. This is the sixth highest health cost and accounts for 7 % of total national health expenditure. Approximately 49 % of Australian children aged 6 years have caries experience in their deciduous teeth and this is rising. The aetiology of dental caries involves a complex interplay of individual, behavioural, social, economic, political and environmental conditions, and there is increasing interest in genetic predisposition and epigenetic modification. Methods The Oral Health Sub-study; a cross sectional study of a birth cohort began in November 2012 by examining mothers and their children who were six years old by the time of initiation of the study, which is ongoing. Data from detailed questionnaires of families from birth onwards and data on mothers’ knowledge, attitudes and practices towards oral health collected at the time of clinical examination are used. Subjects’ height, weight and mid-waist circumference are taken and Body Mass Index (BMI) computed, using an electronic Bio-Impedance balance. Dental caries experience is scored using the International Caries Detection and Assessment System (ICDAS). Saliva is collected for physiological measures. Salivary Deoxyribose Nucleic Acid (DNA) is extracted for genetic studies including epigenetics using the SeqCap Epi Enrichment Kit. Targets of interest are being confirmed by pyrosequencing to identify potential epigenetic markers of caries risk. Discussion This study will examine a wide range of potential determinants for childhood dental caries and evaluate inter-relationships amongst them. The findings will provide an evidence base to plan and implement improved preventive strategies.

Aging response and its effect on the functional properties of Cu–Al–Ni shape memory alloys

The β-phase aging response of Cu–Al–Ni single crystal shape memory alloys (SMAs) within the temperature range of 473–573 K has been investigated. Alloys in austenitic (Cu–14.1Al–4Ni wt.%, alloy A) and martensitic (Cu–13.4Al–4Ni wt.%, alloy M) conditions at room temperature were considered. Aged samples show presence of β1′ and γ1′ martensites in both the alloys and formation of γ2 precipitates in the alloy A. The differential scanning calorimetry (DSC) thermograms of the aged samples show increase in transformation temperatures as well as transformation hysteresis with aging. Dynamic mechanical analysis (DMA) was conducted on both the alloys to ascertain the role of precipitates and martensitic transition on tan δ, which characterizes the damping behaviour of the material. With aging, a steady decrease in tan δ value was observed in both the alloys, which was attributed to the decrease in the number of interfaces per unit area with increasing aging temperature. Moreover, in alloy A, as the volume fraction of precipitate increases with aging, the movement of martensitic interfaces is restricted causing a decreased tan δ.

Interrupted creep behaviour of Mg alloys developed for powertrain applications

A conventional magnesium alloy, AZ91D, and two creep resistant magnesium alloys, developed for powertrain applications, MRI 153M and MRI 230D, are prepared by high pressure die casting. These alloys are tested for their creep behaviour in the continuous manner, as is the Current practice, and in the interrupted manner, which represents the real life Situation more closely. It is observed that the interrupted creep tests give rise to a primary creep appearing at the beginning of each cycle resulting in a higher average strain rate than that encountered in the continuous creep tests. Further, the shorter the cycle time, higher is the average strain rate in the interrupted creep tests. A higher average strain rate will give rise to a higher strain over the same period. This is attributed to the recovery taking place during the cooling and heating between two cycles. The effect of additional precipitation during interrupted creep tests depends on the nature of the precipitates. The additional precipitation of beta phase during the cooling and heating between two cycles increases the steady state strain rate in the AZ91D and MRI 153M alloys. whereas the additional precipitation of C36 phase during the cooling and heating between two cycles decreases the steady state strain rate in the MRI 230D alloy. (C) 2009 Elsevier B.V. All rights reserved.

Patient doses in ct, dental cone beam ct and projection radiography in Finland, with emphasis on paediatric patients

Diagnostic radiology represents the largest man-made contribution to population radiation doses in Europe. To be able to keep the diagnostic benefit versus radiation risk ratio as high as possible, it is important to understand the quantitative relationship between the patient radiation dose and the various factors which affect the dose, such as the scan parameters, scan mode, and patient size. Paediatric patients have a higher probability for late radiation effects, since longer life expectancy is combined with the higher radiation sensitivity of the developing organs. The experience with particular paediatric examinations may be very limited and paediatric acquisition protocols may not be optimised. The purpose of this thesis was to enhance and compare different dosimetric protocols, to promote the establishment of the paediatric diagnostic reference levels (DRLs), and to provide new data on patient doses for optimisation purposes in computed tomography (with new applications for dental imaging) and in paediatric radiography. Large variations in radiation exposure in paediatric skull, sinus, chest, pelvic and abdominal radiography examinations were discovered in patient dose surveys. There were variations between different hospitals and examination rooms, between different sized patients, and between imaging techniques; emphasising the need for harmonisation of the examination protocols. For computed tomography, a correction coefficient, which takes individual patient size into account in patient dosimetry, was created. The presented patient size correction method can be used for both adult and paediatric purposes. Dental cone beam CT scanners provided adequate image quality for dentomaxillofacial examinations while delivering considerably smaller effective doses to patient compared to the multi slice CT. However, large dose differences between cone beam CT scanners were not explained by differences in image quality, which indicated the lack of optimisation. For paediatric radiography, a graphical method was created for setting the diagnostic reference levels in chest examinations, and the DRLs were given as a function of patient projection thickness. Paediatric DRLs were also given for sinus radiography. The detailed information about the patient data, exposure parameters and procedures provided tools for reducing the patient doses in paediatric radiography. The mean tissue doses presented for paediatric radiography enabled future risk assessments to be done. The calculated effective doses can be used for comparing different diagnostic procedures, as well as for comparing the use of similar technologies and procedures in different hospitals and countries.