Flatfish herding behavior in response to trawl sweeps: a comparison of diel responses to conventional sweeps and elevated sweeps

Commercial bottom trawls often have sweeps to herd fish into the net. Elevation of the sweeps off the seaf loor may reduce seafloor disturbance, but also reduce herding effectiveness. In both field and laboratory experiments, we examined the behavior of flatfish in response to sweeps. We tested the hypotheses that 1) sweeps are more effective at herding flatfish during the day than at night, when fish are unable to see approaching gear, and that 2) elevation of sweeps off the seafloor reduces herding during the day, but not at night. In sea trials, day catches were greater than night catches for four out of six flatfish species examined. The elevation of sweeps 10 cm significantly decreased catches during the day, but not at night. Laboratory experiments revealed northern rock sole (Lepidopsetta polyxystra) and Pacific halibut (Hippoglossus stenolepis) were more likely to be herded by the sweep in the light, whereas in the dark they tended to pass under or over the sweep. In the light, elevation of the sweep reduced herding, and more fish passed under the sweep. In contrast, in the dark, sweep elevation had little effect upon the number of fish that exhibited herding behavior. The results of both field and laboratory experiments were consistent with the premise that vision is the principle sensory input that controls fish behavior and orientation to trawl gear, and gear performance will differ between conditions where flatfish can see, in contrast to where they cannot see, the approaching gear.

Comparison of different scheduling techniques for H-infinity controllers

Several approaches to designing schedule H-infinity control systems are compared. These include a controller switching approach and also parameter scheduling of an observer representation of the controller. They are illustrated by application to a Generic VSTOI. Aircraft Model (GVAM) supplied by The Royal Aerospace Establishment (RAE) at Bedford. The switched design has been tested on the simulator at RAE Bedford. The linear H-infinity designs make use of a loop-shaping followed by robust stabilisation to additive perturbations of a normalised coprime factorisation of the shaped plans. The different scheduling approaches are compared with respect to achieved robust stability levels. performance and complexity of implementation.

A comparison of power losses for small (< 1 kW) induction motor drives adopting squarewave and sinusoidal PWM excitation

In this paper the influence of the form of motor excitation on the performance of a small (< 1 kW) induction motor drive is studied. Two forms of excitation, namely sine waves generated by pulse width modulation and simple square wave are explored. Sine wave excitation gives lower motor losses but increases inverter losses. Conversely, square wave excitation increases motor losses but decreases inverter losses. Losses have been measured directly by calorimetric means or, in the case of the inverter, predicted by a Pspice model that has been verified by calorimetric methods. The work shows that overall, the use of square wave excitation leads to a more efficient drive. © 2004 The Institution of Electrical Engineers.

Comparison of stabilised/solidified mixes of model drill cuttings based on the North Sea and Red Sea Areas

Following the global stringent legislations regulating the wastes generated from the drilling process of oil exploration and production activities, the management of hazardous drill cuttings has become one of the pressing needs confronting the petroleum industry. Most of the prevalent treatment techniques adopted by oil companies are extremely expensive and/or the treated product has to be landfilled without any potential end-use; thereby rendering these solutions unsustainable. The technique of stabilisation/solidification is being investigated in this research to treat drill cuttings prior to landfilling or for potential re-use in construction products. Two case studies were explored namely North Sea and Red Sea. Given the known difficulties with stabilising/solidifying oils and chlorides, this research made use of model drill cutting mixes based on typical drill cutting from the two case studies, which contained 4.2% and 10.95% average concentrations of hydrocarbons; and 2.03% and 2.13% of chlorides, by weight respectively. A number of different binders, including a range of conventional viz. Portland cement (PC) as well as less-conventional viz. zeolite, or waste binders viz. cement kiln dust (CKD), fly ash and compost were tested to assess their ability to treat the North Sea and Red Sea model drill cuttings. The dry binder content by weight was 10%, 20% and 30%. In addition, raw drill cuttings from one of the North Sea offshore rigs were stabilised/solidified using 30% PC. The characteristics of the final stabilised/solidified product were finally compared to those of thermally treated cuttings. The effectiveness of the treatment using the different binder systems was compared in the light of the aforementioned two contaminants only. A set of physical tests (unconfined compressive strength (UCS)), chemical tests (NRA leachability) and micro-structural examinations (using scanning electron microscopy (SEM), and X-ray diffraction (XRD)) were used to evaluate the relative performance of the different binder mixes in treating the drill cuttings. The results showed that the observed UCS covered a wide range of values indicating various feasible end-use scenarios for the treated cuttings within the construction industry. The teachability results showed the reduction of the model drill cuttings to a stable non-reactive hazardous waste, compliant with the UK acceptance criteria for non-hazardous landfills: (a) by most of the 30% and 20% binders for chloride concentrations, and (b) by the 20% and 30% of compost-PC and CKD-PC binders for the Red Sea cuttings. The 20% and 30% compost-PC and CKD-PC binders successfully reduced the leached oil concentration of the North Sea cuttings to inert levels. Copyright 2007, Society of Petroleum Engineers.

Studies on isolation of salmonella from sea foods 1. Comparison of enrichment and selective media for recovery of salmonellae from fish

Three enrichment broths and six plating media were compared for efficiency of detection Salmonella in the presence of numbers of Coliforms (10super(5)/ml) and proteus (10super(3)/ml) from artificially inoculated fish samples. Recovery experiments Salmonella anatum, S. typhimurium and S. enteritidis indicated that the two enrichment broths Dulcitol Selinite (DSE) and Selinite Cystine (SC) were equally efficient. Further, the viability of Salmonella, inoculated into fish muscle and kept at 4°C for 48 hours, was found to be not affected by the low temperature storage. Selective plating media like Xylose Lysine Deoxycholate agar (XLD), Brilliant Green Sulphadiazine agar (BGS) and Brilliant Green agar (BG) were found to be superior in performance to Salmonella-Shigella agar: (SS) and Bismuth Sui phite agar (BiS).

A comparison of four sustainable manufacturing strategies

Effective use of materials is one possible component of a sustainable manufacturing strategy. There are many such strategies proposed in the literature and used in practice, with confusion over what they are, what the differences among them may be and how they can be used by practitioners in design and manufacture to improve the sustainability of their product and processes. This paper reviews the literature on sustainable manufacturing strategies that deliver improved material performance. Four primary strategies were found: waste minimisation; material efficiency; resource efficiency; and eco-efficiency. The literature was analysed to determine the key characteristics of these sustainable manufacturing strategies and 17 characteristics were found. The four strategies were then compared and contrasted against all the characteristics. While current literature often uses these strategy titles in a confusing, occasionally inter-changeable manner, this study attempts to create clear separation between them. Definition, scope and practicality of measurement are shown to be key characteristics that impact upon the ability of manufacturing companies to make effective use of the proposed strategy. It is observed that the most actionable strategies may not include all of the dimensions of interest to a manufacturer wishing to become more sustainable, creating a dilemma between ease of implementation and breadth of impact. © 2008 Taylor & Francis.

A comparison of cage and nested-loop BDFM rotors

The Brushless Double-Fed Machine (BDFM) is a type of variable speed generator or drive. Using theoretical analysis of simple BDFM rotors this paper establishes trends in how rotor structures determine the rotor's equivalent circuit resistance, leakage inductance and turns ratio. The variation in measured parameters of five prototype rotors is then analysed in light of the trends found. Both the theory and experimental results suggest a significant performance advantage in using cage+loops type rotors as opposed to the simple nested loop type more usually employed.

Comparison of Camera Motion Estimation Methods for 3D Reconstruction of Infrastructure

Camera motion estimation is one of the most significant steps for structure-from-motion (SFM) with a monocular camera. The normalized 8-point, the 7-point, and the 5-point algorithms are normally adopted to perform the estimation, each of which has distinct performance characteristics. Given unique needs and challenges associated to civil infrastructure SFM scenarios, selection of the proper algorithm directly impacts the structure reconstruction results. In this paper, a comparison study of the aforementioned algorithms is conducted to identify the most suitable algorithm, in terms of accuracy and reliability, for reconstructing civil infrastructure. The free variables tested are baseline, depth, and motion. A concrete girder bridge was selected as the "test-bed" to reconstruct using an off-the-shelf camera capturing imagery from all possible positions that maximally the bridge's features and geometry. The feature points in the images were extracted and matched via the SURF descriptor. Finally, camera motions are estimated based on the corresponding image points by applying the aforementioned algorithms, and the results evaluated.

Comparison of square and hexagonal fuel lattices for high conversion PWRs

This paper reports on an investigation into fuel design choices of a pressurized water reactor operating in a self-sustainable Th- 233U fuel cycle. In order to evaluate feasibility of this concept, two types of fuel assembly lattices were considered: square and hexagonal. The hexagonal lattice may offer some advantages over the square one. For example, the fertile blanket fuel can be packed more tightly reducing the blanket volume fraction in the core and potentially allowing to achieve higher core average power density. The calculations were carried out with Monte-Carlo based BGCore code system and the results were compared to those obtained with Serpent Monte-Carlo code and deterministic transport code BOXER. One of the major design challenges associated with the SB concept is high power peaking due to the high concentration of fissile material in the seed region. The second objective of this work is to estimate the maximum achievable core power density by evaluation of limiting thermal hydraulic parameters. The analysis showed that both fuel assembly designs have a potential of achieving net breeding. Although hexagonal lattice was found to be somewhat more favorable because it allows achieving higher power density, while having breeding performance comparable to the square lattice case. © Carl Hanser Verlag München.

Comparison of stationary acoustic monitoring and visual observation of finless porpoises

The detection performance regarding stationary acoustic monitoring of Yangtze finless porpoises Neophocaena phocaenoides asiaeorientalis was compared to visual observations. Three stereo acoustic data loggers (A-tag) were placed at different locations near the confluence of Poyang Lake and the Yangtze River, China. The presence and number of porpoises were determined acoustically and visually during each 1-min time bin. On average, porpoises were acoustically detected 81.7 +/- 9.7% of the entire effective observation time, while the presence of animals was confirmed visually 12.7 +/- 11.0% of the entire time. Acoustic monitoring indicated areas of high and low porpoise densities that were consistent with visual observations. The direction of porpoise movement was monitored using stereo beams, which agreed with visual observations at all monitoring locations. Acoustic and visual methods could determine group sizes up to five and ten individuals, respectively. While the acoustic monitoring method had the advantage of high detection probability, it tended to underestimate group size due to the limited resolution of sound source bearing angles. The stationary acoustic monitoring method proved to be a practical and useful alternative to visual observations, especially in areas of low porpoise density for long-term monitoring.

Comparison of two kinds of active layers for high-power narrow-stripe distributed feedback laser diodes

Usually GaAs/AlGaAs is utilized as an active layer material in laser diodes operating in the spectral range of 800 850 nm. In this work, in addition to a traditional unstrained GaAs/AlGaAs distributed feedback (DFB) laser diode, a compressively strained InGaAlAs/AlGaAs DFB laser diode is numerically investigated in characteristic. The simulation results show that the compressively strained DFB laser diode has a lower transparency carrier density, higher gain, lower Auger recombination rate, and higher stimulated recombination rate, which lead to better a device performance, than the traditional unstrained GaAs/AlGaAs DFB laser diode.

Comparison of photobioreactors and optimal light regime for rapid vegetative propagation of transgenic Undaria pinnatifida gametophytes

BACKGROUND: Previously, tachyplesin gene (tac) has been successfully transferred into Undaria pinnatifida gametophytes using the method of microprojectile bombardment transformation. The objectives of this study were to compare and evaluate the performance of bubble-column and airlift bioreactors to determine a preferred configuration of bioreactor for vegetative propagation of transgenic U. pinnatifida gametophytes, and to then investigate the influence of light on vegetative propagation of these gametophytes, including incident light intensity, photoperiod and light quality to resolve the problems of rapid vegetative propagation within the selected bioreactor. RESULTS: Experimental results showed that final dry cell density in the airlift bioreactor was 12.7% higher than that in the bubble-column bioreactor under the optimal aeration rate of 1.2 L air min(-1) L-1 culture. And a maximum final dry cell density of 2830 mg L-1 was obtained within the airlift bioreactor using blue light at 40 mu mol m(-2) s(-1) with a light/dark cycle of 14/10 (h). Polymerase chain reaction (PCR) analysis indicated that genes (bar and tac) were not lost during rapid vegetative propagation within the airlift bioreactor. CONCLUSION: The airlift bioreactor was shown to be much more suitable for rapid vegetative propagation of transgenic U. pinnatifida gametophytes than the bubble-column bioreactor in the laboratory. The use of blue light allows improvement of vegetative propagation of transgenic U. pinnatifida gametophytes. (C) 2009 Society of Chemical Industry

Animated virtual agents to cue user attention: comparison of static and dynamic deictic cues on gaze and touch responses

This paper describes an experiment developed to study the performance of virtual agent animated cues within digital interfaces. Increasingly, agents are used in virtual environments as part of the branding process and to guide user interaction. However, the level of agent detail required to establish and enhance efficient allocation of attention remains unclear. Although complex agent motion is now possible, it is costly to implement and so should only be routinely implemented if a clear benefit can be shown. Pevious methods of assessing the effect of gaze-cueing as a solution to scene complexity have relied principally on two-dimensional static scenes and manual peripheral inputs. Two experiments were run to address the question of agent cues on human-computer interfaces. Both experiments measured the efficiency of agent cues analyzing participant responses either by gaze or by touch respectively. In the first experiment, an eye-movement recorder was used to directly assess the immediate overt allocation of attention by capturing the participant’s eyefixations following presentation of a cueing stimulus. We found that a fully animated agent could speed up user interaction with the interface. When user attention was directed using a fully animated agent cue, users responded 35% faster when compared with stepped 2-image agent cues, and 42% faster when compared with a static 1-image cue. The second experiment recorded participant responses on a touch screen using same agent cues. Analysis of touch inputs confirmed the results of gaze-experiment, where fully animated agent made shortest time response with a slight decrease on the time difference comparisons. Responses to fully animated agent were 17% and 20% faster when compared with 2-image and 1-image cue severally. These results inform techniques aimed at engaging users’ attention in complex scenes such as computer games and digital transactions within public or social interaction contexts by demonstrating the benefits of dynamic gaze and head cueing directly on the users’ eye movements and touch responses.

Screening the human exome: a comparison of whole genome and whole transcriptome sequencing.

BACKGROUND: There is considerable interest in the development of methods to efficiently identify all coding variants present in large sample sets of humans. There are three approaches possible: whole-genome sequencing, whole-exome sequencing using exon capture methods, and RNA-Seq. While whole-genome sequencing is the most complete, it remains sufficiently expensive that cost effective alternatives are important. RESULTS: Here we provide a systematic exploration of how well RNA-Seq can identify human coding variants by comparing variants identified through high coverage whole-genome sequencing to those identified by high coverage RNA-Seq in the same individual. This comparison allowed us to directly evaluate the sensitivity and specificity of RNA-Seq in identifying coding variants, and to evaluate how key parameters such as the degree of coverage and the expression levels of genes interact to influence performance. We find that although only 40% of exonic variants identified by whole genome sequencing were captured using RNA-Seq; this number rose to 81% when concentrating on genes known to be well-expressed in the source tissue. We also find that a high false positive rate can be problematic when working with RNA-Seq data, especially at higher levels of coverage. CONCLUSIONS: We conclude that as long as a tissue relevant to the trait under study is available and suitable quality control screens are implemented, RNA-Seq is a fast and inexpensive alternative approach for finding coding variants in genes with sufficiently high expression levels.

Comparison of dynamic balance in adolescent male soccer players from rwanda and the United States.

PURPOSE/BACKGROUND: Dynamic balance is an important component of motor skill development. Poor dynamic balance has previously been associated with sport related injury. However, the vast majority of dynamic balance studies as they relate to sport injury have occurred in developed North American or European countries. Thus, the purpose of this study was to compare dynamic balance in adolescent male soccer players from Rwanda to a matched group from the United States. METHODS: Twenty-six adolescent male soccer players from Rwanda and 26 age- and gender-matched control subjects from the United States were screened using the Lower Quarter Y Balance Test during their pre-participation physical. Reach asymmetry (cm) between limbs was examined for all reach directions. In addition, reach distance in each direction (normalized to limb length, %LL) and the composite reach score (also normalized to %LL) were examined. Dependent samples t-tests were performed with significant differences identified at p<0.05. RESULTS: Twenty-six male soccer players from Rwanda (R) were matched to twenty-six male soccer players from the United States (US). The Rwandan soccer players performed better in the anterior (R: 83.9 ± 3.2 %LL; US: 76.5 ± 6.6 %LL, p<0.01), posterolateral (R: 114.4 ± 8.3 %LL ; US: 106.5 ± 8.2 %LL, p<0.01) and composite (R: 105.6 ± 1.3 %LL; US: 97.8 ± 6.2 %LL, p<0.01) reach scores. No significant differences between groups were observed for reach asymmetry. CONCLUSIONS: Adolescent soccer players from Rwanda exhibit superior performance on a standardized dynamic balance test as comparison to similar athletes from the United States. The examination of movement abilities of athletes from countries of various origins may allow for a greater understanding of the range of true normative values for dynamic balance. LEVELS OF EVIDENCE: 3b.