Efeito da adição de fibras da palma do licuri (syagrus coronata) no comportamento físico e mecânico de compósitos de matriz cimentícia

This research was motivated by the requirement of asbestos s replacement in building systems and the need to generate jobs and income in the country side of the state of Bahia, Brazil. The project aimed at using fibers from licuri leaves (syagrus coronata), an abundant palm in the region, to produce composites appropriate for the sustainable production of cement fibre reinforced products in small plants. The composites were produced in laboratory using Portland cement CP-II-F32, sand, water, licuri palm fiber contents of 1.0, 1.5 and 2.0% by weight of binder (two different fiber length) and metakaolin. The latter was chosen as an additional binder for its efficiency to reduce the alkalinity of cementitious matrixes therefore preventing the degradation of vegetable fibers. The characterization of the composite components was carried out by sieving and laser particle size analyses, thermal analysis, fluorescence and X-ray diffraction. The composites performance was evaluated by 3- point-bending tests, compressive strength, ultrasound module of elasticity, free and restrained shrinkage, water capillarity absorption and apparent specific gravity. It has been found that the addition of fibers increased the time to onset of cracking over 200.00% and a 25% reduction in cracks opening in the restrained shrinkage test. The capillary absorption reduced about 25% when compared to fiber-free composites. It was also observed with regard to flexural strength, compressive strength and specific gravity, that the addiction of fibers did not affect the composite performance presenting similar results for compounds with and without fibers. In general it can be stated that the reinforced composite fibers of palm licuri presents physical and mechanical characteristics which enable them to be used in the intended proposals of this research

Aditivação de pastas geopoliméricas com tetraborato de sódio e látex não iônico para cimentação de Poços de Petróleo

The development of activities in the oil and gas sector has been promoting the search for materials more adequate to oilwell cementing operation. In the state of Rio Grande do Norte, the cement sheath integrity tend to fail during steam injection operation which is necessary to increase oil recovery in reservoir with heavy oil. Geopolymer is a material that can be used as alternative cement. It has been used in manufacturing of fireproof compounds, construction of structures and for controlling of toxic or radioactive waste. Latex is widely used in Portland cement slurries and its characteristic is the increase of compressive strength of cement slurries. Sodium Tetraborate is used in dental cement as a retarder. The addition of this additive aim to improve the geopolymeric slurries properties for oilwell cementing operation. The slurries studied are constituted of metakaolinite, potassium silicate, potassium hydroxide, non-ionic latex and sodium tetraborate. The properties evaluated were: viscosity, compressive strength, thickening time, density, fluid loss control, at ambient temperature (27 ºC) and at cement specification temperature. The tests were carried out in accordance to the practical recommendations of the norm API RP 10B. The slurries with sodium tetraborate did not change either their rheological properties or their mechanical properties or their density in relation the slurry with no additive. The increase of the concentration of sodium tetraborate increased the water loss at both temperatures studied. The best result obtained with the addition of sodium tetraborate was thickening time, which was tripled. The addition of latex in the slurries studied diminished their rheological properties and their density, however, at ambient temperature, it increased their compressive strength and it functioned as an accelerator. The increase of latex concentration increased the presence of water and then diminished the density of the slurries and increased the water loss. From the results obtained, it was concluded that sodium tetraborate and non-ionic latex are promising additives for geopolymer slurries to be used in oilwell cementing operation

Desenvolvimento de sistemas de aditivos químicos para aplicação em cimentações de poços de petróleo

The primary cementing is an important step in the oilwell drilling process, ensuring the mechanical stability of the well and the hydraulic isolation between casing and formation. For slurries to meet the requirements for application in a certain well, some care in the project should be taken into account to obtain a cement paste with the proper composition. In most cases, it is necessary to add chemicals to the cement to modify its properties, according to the operation conditions and thus obtain slurries that can move inside the jacket providing a good displacement to the interest area. New technologies of preparation and use of chemicals and modernization of technological standards in the construction industry have resulted in the development of new chemical additives for optimizing the properties of building materials. Products such as polycarboxylate superplasticizers provide improved fluidity and cohesion of the cement grains, in addition to improving the dispersion with respect to slurries without additives. This study aimed at adapting chemical additives used in civil construction to be used use in oilwell cement slurries systems, using Portland cement CPP-Special Class as the hydraulic binder. The chemical additives classified as defoamer, dispersant, fluid loss controller and retarder were characterized by infrared absorption spectroscopy, thermogravimetric analyses and technological tests set by the API (American Petroleum Institute). These additives showed satisfactory results for its application in cement slurries systems for oil wells. The silicone-based defoamer promoted the reduction of air bubbles incorporated during the stirring of the slurries. The dispersant significantly reduced the rheological parameters of the systems studied. The tests performed with the fluid loss controller and the retarder also resulted in suitable properties for application as chemical additives in cement slurries

Estudo da formulação de pré-misturas secas para a cimentação de poços em terra

An economical solution for cementing oil wells is the use of pre-prepared dry mixtures containing cement and additives. The mixtures may be formulated, prepared and transported to the well where is added water to be pumped.Using this method, becomes dispensable to prepare the cement mixes containing additives in the cementing operation, reducing the possibility of error. In this way, the aim of this work is to study formulations of cement slurries containing solid additives for primary cementing of oil wells onshore for typical depths of 400, 800 and 1,200 meters. The formulations are comprised of Special Class Portland cement, mineral additions and solids chemical additives.The formulated mixtures have density of 1.67 g / cm ³ (14.0 lb / gal). Their optimization were made through the analysis of the rheological parameters, fluid loss results, free water, thickening time, stability test and mechanical properties.The results showed that mixtures are in conformity the specifications for cementing oil wells onshore studied depths

Estudo do comportamento no estado fresco e endurecido do concreto com incorporação de resíduo de corte de botão

This works aims at investigating the effects of adding waste from RCBP-polyester button manufacturing to Portland cement concrete, particularly regarding its consistency and mechanic strength. The RCBP used came from a button factory located in Parnamirim, RN, Brazil. The waste was added to the concrete on different ratios: 5 %, 10 %, 15 % and 20 % of the total cement mass. A sample of concrete without the RCBP was used as reference, 1:1,33:2,45:0,50. For the mechanic strength test four samples were tested with different ages (3, 7 and 28 days old) and mixtures. Furthermore, a Slump Test was also conducted in order to verify the concrete s consistency. A tendency to a reduction in the compression resistance was noticed for all samples. For the samples with 5 % and 10 %, there was also an increase in the traction resistance during inflexion, regarding the reference concrete. In the microstructural analysis, the RBCP was observed to show an irregular and porous surface, thus explaining the consistency decrease

Estudo do comportamento mecânico de areias artificialmente cimentadas

Soil improved with the addition of cement have been utilized as an alternative to the construction of various types of geotechnical works, almost always present economic and environmental advantages. This paper presents a study on the usage of cement in the improvement of mechanical properties of sandy soils, characteristic of the region of Natal, collected from its dunes. This research was made in order to analyze the influence of cement content, voids, and also including water immersion and confining pressure. Samples molded from cement-soil mixtures were tested for unconfined compression tests and triaxial tests. The samples had the percentage of cement mixed in 2.5%, 5% and 10% by weight. The cement agent used was the Portland Cement of High Early strength(CPV-ARI), which promoted agility to the experimental procedure for presenting a rapid gain in strenght. The void ratio used ranged from 0.7 (more compact), 0,9 and 1,1(softer). The soil under study can be considered as pure sand. In general, it can be stated that the larger the amount of cement added to the sand studied is, the greater ultimate strength will be. Likewise, as more compact the soil is, the less void ratio and more resistant it will be present. The confining pressure tends to increase the resistance of the specimens. The cementing adopted grades showed that the use of different criteria for failure did not significantly alter the stress-strain parameters for the sand studied. The angle of friction values were found within the typical range of medium and compact sands. Cementing acted in the sand providing an intercepted cohesion which increased enhancing the potential cementation. In triaxial compression tests, the sand with void ratio is equal to 0.7 and showed the expected behavior for a compact sand while the stress-strain behavior of the same sand with the void ratio of 0.9 tended to be expected for the soft sand as well

Adição de geomanta e tecido não tecido de polipropileno em cimentos geopoliméricos de pega rápida

Geopolymers are cementing materials that depict a number of advantages compared to Portland cement. Contrary to the latter, geopolymers are synthesized at room temperature, thus significantly reducing the emission of CO2 to the atmosphere. Moreover, the composition and synthesis reactions can be tailored to adjust the setting time of the material as well as its compressive mechanical strength. It is then possible to produce geopolymeric cements with short setting times and high compressive strength, although relatively brittle. The objective of the present study was to produce and characterize composite materials by reinforcing fastsetting geopolymeric matrixes with polypropylene geosynthetics (geomats and geotextiles) in an attempt to improve the toughness and tensile strength of the cementing material. Geosynthetics have been increasingly used to reinforce engineering structures, providing higher strength and better toughness. In particular, polypropylene nonwoven and geomats depict other attractive properties such as low density, durability, impact absorption and resistance to abrasion. Fast-setting geopolymers were then synthesized and reinforced with polypropylene nonwoven and geomats. The mechanical strength of the materials, reinforced or not, was characterized. The results showed that relatively short setting times and adequate flowing behavior were achieved by adjusting the composition of the geopolymer. In addition, it is possible to improve the fracture resistance of geopolymeric cements by adding polypropylene geosynthetics. The best results were achieved by reinforcing geopolymer with polypropylene TNT

Influência da formação de pozolanas com adição de metacaulim em concreto de alta resistência

The need to build durable structures and resistant to harsh environments enabled the development of high strength concrete, these activities generate a high cement consumption, which implies factor in CO2 emissions. Often the desired strength is not achieved using only the cement composition. This study aims to evaluate the influence of pozzolans with the addition of metakaolin on the physical mechanics of high strength concrete comparing them with the standard formulation. Assays were performed to characterize the aggregates according to NBR 7211, evaluation of cement and coarse aggregate through the trials of petrography (NBR 15577-3/08) and alkali-aggregate reaction (NBR 15577-05/08). Specimens were fabricated according to NBR 5738-1/04 with additions of 0%, 4%, 6%, 8% and 10% of metakaolin for cement mortars CP V in the formulations. For evaluation of the concrete hardened in fresh state and scattering assays were performed and compressive strength in accordance with the NBR 7223/1992 and NBR 5739-8/94 respectively. The results of the characterization of aggregates showed good characteristics regarding size analysis and petrography, as well as potentially innocuous as the alkali-aggregate reaction. As to the test of resistance to compression, all the formulations with the addition of metakaolin showed higher value at 28 days of disruption compared with the standard formulation. These results present an alternative to reduce CO2 emissions, and improvements in the quality and durability of concrete, because the fine particle size of metakaolin provides an optimal compression of the mass directly influencing the strength and rheology of the dough

Aplicação do conceito de maturidade em concreto com adição de cinza de casca de arroz

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Concreto de alto desempenho com adição de resíduos de borracha de pneu

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Aspectos biológicos e bioatividade de materiais a base de MTA em cultura de células

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Aproveitamento dos resíduos gerados pelo processamento industrial/artesanal de pedra-sabão da região de Ouro Preto

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Estudo de parâmetros físicoquímicos para a produção de argamassas utilizando resíduos industriais e da construção civil

As argamassas podem ser consideradas como a mistura de aglomerantes e agregados com água, possuindo capacidade de endurecimento e aderência. Como alternativa, é proposto produção de argamassas utilizando como agregado miúdo resíduos de construção civil (RCC), rico em silicoaluminatos, gerado nas obras de demolições e reformas, e cinza volante (CV) como material pozolânico, obtida a partir da combustão do carvão mineral em caldeiras de leitos fluidizados, em substituição parcial ao cimento Portland. Neste contexto, o resíduo de construção civil foi beneficiado e caracterizado pelas análises de espectrofotometria de raios- X e difração de raios-X, a cinza volante foi caracterizada pela análise granulométrica e espectrofotometria de raios-X. Para produção das argamassas formularam-se composições de RCC nas proporções de 95, 90, 85, 80, 75 e 70%; CV de 0, 5, 10, 15, 20 e 25% e 5% de cimento Portland CP II Z 32, sendo que em cada composição do traço de argamassa foi adicionado 0,8% em volume de água e para o ensaio reológico utilizou-se as mesmas proporções de resíduos (RCC e CV) com 35% em volume de água. Após a cura de 28 dias os corpos de prova foram submetidos a ensaios físicos de absorção, porosidade e massa específica aparente; ensaio mecânico de resistência à compressão e análise de difração de raios-X e microscopia eletrônica de varredura, cujos resultados obtidos mostraram-se ser viável a utilização da cinza volante e RCC na construção civil, na produção de argamassas.

Influência do teor de cinza volante na reologia de argamassa de assentamento: fabricado com reciclagem de resíduos

As argamassas podem ser consideradas como um conjunto de partículas sólidas em suspensão (agregado miúdo), aglomerantes e água (pasta de cimento). Sendo assim, seu comportamento reológico durante a cura pode ser influenciado por fatores como a granulometria, composição e teor de água incorporado. Este trabalho estudou as características reológicas de seis composições de argamassas, em função do teor de cinza volante, como material de atividade pozolânica, em substituição parcial do cimento. A argamassa estudada utilizou como base agregado o resíduo da construção civil (RCC), devidamente caracterizado por difratometria e fluorescência de raios-X. Formularam-se composições de argamassas para os ensaios reológicos com adição de resíduo de construção civil (RCC) nas proporções de 95, 90, 85, 80, 75 e 70%; cinzas volantes (CV) 0, 5, 10, 15, 20 e 25% e 5% de Cimento Portland Comum (CP II- E 32), sendo que em cada amostra foi incorporado 35% de água. Utilizou-se o viscosímetro modelo VT 550, com sensor tipo cilindros coaxiais SV₁ – Haake a temperatura de 28ºC. Para avaliar o tempo de cura do material programou-se uma taxa de cisalhamento constante 53,4 s^-1 em 1h e 45min, sendo avaliado o torque em intervalos de 15min. Para a elaboração das curvas de fluxo e curvas de histerese, utilizou-se a taxa de cisalhamento entre 0 e 600 s^-1 no intervalo de tempo de 120s. Os resultados mostraram que a incorporação de cinza volante foi o principal fator para aumento do torque no tempo de cura das argamassas e mudança do comportamento de reópetico para tixotrópico, nos traços analisados. Os dados experimentais das formulações propostas ajustaram-se ao modelo reológico de Herschel-Bulkley.

Atividade pozolânica de arenito zeolítico da região Nordeste do Brasil

No nordeste do Brasil, existe a ocorrência de zeolitas sedimentares relacionadas a arenitos, descoberta nos anos 2000. Esses arenitos são constituídos de quartzo, zeolitas naturais (estilbita) e argilominerais (esmectita). Estudos preliminares constataram que esse arenito pode ser empregado como material pozolânico em sistemas à base de cimento Portland, desde que o material seja peneirado para remoção do quartzo e ativado termicamente, uma vez que a estilbita é zeolita de baixa atividade pozolânica. O objetivo geral desse trabalho foi determinar qual a fração granulométrica que proporciona a maior concentração de zeolita e esmectita e a temperatura de calcinação que acarreta a maior atividade pozolânica. No programa experimental, empregou-se o arenito zeolítico passante nas peneiras #200 e #325 e calcinado às temperaturas de 150ºC, 300ºC e 500ºC. A análise da caracterização mineralógica das amostras peneiradas foi realizada por difração de raios X, por análises termogravimétrica e termodiferencial. Para avaliação da reatividade, foram realizados ensaios mecânicos de atividade pozolânica em argamassas de cal hidratada e cimento Porltand. Os resultados mostraram que a amostra peneirada na peneira #200 foi a mais adequada porque apresentou elevada concentração de estilbita e um percentual maior de material passante em comparação a amostra da peneira #325, 15% e 2% respectivamente. A temperatura de calcinação de 500ºC foi a que proporcionou a maior atividade pozolânica, em razão da modificação mais efetiva da estrutura cristalina, tanto da estilbita, como da esmectita. As temperaturas mais moderadas a 150ºC e 300ºC não foram suficientes para a obtenção dos mesmos resultados. As argamassas com o arenito passante na peneira #200 e calcinado a 500ºC atingiram os valores limites mínimos exigidos para que um material seja considerado pozolânico, no caso, 6 MPa para argamassas de cal hidratada e 75% para o índice de atividade pozolânica (IAP).