Symmetrically tapered <30-micron-thick quasi-planar Ge waveguides as chemical sensors for microanalysis

Symmetrically tapered planar IR waveguides have been fabricated by starting with a ZnS coated concave piece of single-crystal Ge, embedding it in an epoxide resin as a supporting substrate, and then grinding and polishing a planar surface until the thickness at the taper minimum is <30 μm. Such tapering is expected to enhance a waveguide's sensitivity as an evanescent wave sensor by maximizing the amount of evanescent wave energy present at the thinnest part of the waveguide. As predicted by theory, the surface sensitivity, i.e., the absorbance signal per molecule in contact with the sensing region, increases with decreasing thickness of the tapered region even while the total energy throughput decreases. The signal-to-noise ratio obtained depends very strongly on the quality of the polished surfaces of the waveguides. The surface sensitivity is superior to that obtained with a commercial Ge attenuated total reflection (ATR) accessory for several types of sample, including thin films (<10 ng) and small volumes (<1 μL) of volatile solvents. By using the waveguides, light-induced structural changes in the protein bacteriorhodopsin were observable using samples as small as ∼50 pmol (∼1 μg). In addition, the waveguide sensors can reveal the surface compositions on a single human hair, pointing to their promise as a tool for forensic fiber analysis.

Effect of nano-Al2O3 addition on the densification of YSZ electrolytes

This work investigates the effect of nanosized Al2O3 addition on the sinterability of YSZ electrolyte. (1-x)YSZ + Al2O3 ceramics with compositions x = 0 to 0.01 were prepared by the conventional mixed oxide route from a commercial powder suspension (particle size <50 nm), and sintered at 1200 to 1500 degrees C for 2 hours in air. Densification, phase evolution, and microstructure were characterized by SEM/EDS and XRD. An improvement in sintered density was observed for the samples with 0.2 to 0.5 mol% Al2O3, though depending on the sintering temperature. Only cubic zirconia was detected as crystalline phase, although XRD features suggested chemical interactions depending upon the amount of Al2O3. The grain size of YSZ was homogeneous and no second phase segregation was detected in the tested range of incorporated nano-Al2O3 and sintering temperatures.

Physical, chemical and biological characterization of membrane fouling

In this chapter, advanced characterization of membrane fouling as a diagnostic tool has been summarized to prevent membrane fouling. Physical, chemical and biological analyses as membrane autopsies are mainly utilized to better understand membrane foulant. The physical characterization gives structure, roughness, charge effect, strength and hydrophobicity of membrane fouling. The chemical methods provide qualitative and quantitative measurements of different inorganic and organic matter. The biological properties present the spatial biofilm distribution, structure of dominant microorganisms and isolation and identification of microorganisms. In addition, detailed membrane foulant types are reviewed in terms of structure, roughness, hydrophobicity, charge effect, strength, calcium, magnesium, aluminum, iron, silicate, particle, functional group, biopolymer, humic acid, polysaccharide, structural composition, biofilm structure, microorganism and foulant interaction.

Chemical immobilization of adult female Weddell seals with tiletamine and zolazepam: effects of age, condition and stage of lactation

Background

Chemical immobilization of Weddell seals (Leptonychotes weddellii) has previously been, for the most part, problematic and this has been mainly attributed to the type of immobilizing agent used. In addition to individual sensitivity, physiological status may play an important role. We investigated the use of the intravenous administration of a 1:1 mixture of tiletamine and zolazepam (Telazol®) to immobilize adult females at different points during a physiologically demanding 5–6 week lactation period. We also compared performance between IV and IM injection of the same mixture.
Results

The tiletamine:zolazepam mixture administered intravenously was an effective method for immobilization with no fatalities or pronounced apnoeas in 106 procedures; however, there was a 25 % (one animal in four) mortality rate with intramuscular administration. Induction time was slightly longer for females at the end of lactation (54.9 ± 2.3 seconds) than at post-parturition (48.2 ± 2.9 seconds). In addition, the number of previous captures had a positive effect on induction time. There was no evidence for effects due to age, condition (total body lipid), stage of lactation or number of captures on recovery time.
Conclusion

We suggest that intravenous administration of tiletamine and zolazepam is an effective and safe immobilizing agent for female Weddell seals. Although individual traits could not explain variation in recovery time, we suggest careful monitoring of recovery times during longitudinal studies (> 2 captures). We show that physiological pressures do not substantially affect response to chemical immobilization with this mixture; however, consideration must be taken for differences that may exist for immobilization of adult males and juveniles. Nevertheless, we recommend a mass-specific dose of 0.50 – 0.65 mg/kg for future procedures with adult female Weddell seals and a starting dose of 0.50 mg/kg for other age classes and other phocid seals.

Taking the sting out of darting : Risks, restraint drugs and procedures for the chemical restraint of Southern Hemisphere otariids

The need to manage otariid populations has necessitated the development of a wide range of capture methods. Chemical restraint by remote drug delivery (i.e., darting) is a highly selective method that can be used to facilitate otariid capture in a range of scenarios, when other methods may be impracticable. However, the risks associated with darting otariids are not widely known and guidelines necessary to promote and refine best practice do not exist. We review the risks associated with darting and in light of our findings, develop darting guidelines to help practitioners assess and minimize risks during capture, anesthesia and recovery. Published studies reveal that mortalities associated with darting predominantly result from complications during anesthetic maintenance (e.g., prolonged respiratory depression, apnea, or hyperthermia), rather than from complications during capture or recovery. In addition to monitoring vital signs and proper intervention, the risk of irreversible complications during anesthesia can be reduced by administering drug doses that are sufficient to enable the capture and masking of animals, after which anesthetic depth can be regulated using gas anesthesia.

Effect of the estufagem process on the chemical constituents of Madeira wines

Madeira wine is a product of well-established reputation, whose aroma and flavour is the result of unique combinations. Particularly, its maturation may include estufagem, wherein wine is usually heated at 45 °C for three months. During this period, several chemical changes may occur, so it is essential to assess its impact on the wine. In this sense, the main objective of the thesis was to evaluate the effect estufagem on the chemical constituents of Madeira wine, specifically on those molecules potentially important in the development of its typical features. Firstly, analytical methodologies capable of determining the target compounds, combining precision and reproducibility to execution effectiveness, were developed. Then various monovarietal Madeira wines were analysed during estufagem under standard and overheating conditions in order to assess its effect. The following compounds were evaluated: furans, amino acids, biogenic amines, polyphenols, organic acids and volatile compounds. In addition, the total polyphenolic composition, the antioxidant potential and the colour of these wines were also evaluated. The results show that most constituents change due to the heating process. Particularly, the heating promotes the development of 5-hydroxymethylfurfural (HMF) in sweet wines submitted to estufagem at higher temperatures. Moreover, estufagem provides the decrease of most amino acids, suggesting their involvement in the formation of the bouquet of these wines. Regarding the total polyphenol content and antioxidant potential of these wines they do not seem to be greatly affected by the heating step, however most monomeric polyphenols decrease during this process. The thermal processing of Madeira wines favours the development of the volatile composition, especially of volatiles usually reported as typical aromas of Madeira wines. Finally, it was demonstrated that the thermal degradation of sugars, especially of fructose, promotes the emergence of volatile compounds identified in baked wines.

Changes in biomass, chemical composition and nutritive value of Spartina alterniflora due to organic pollution in the Itanhaém River Basin (SP, Brazil)

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Chemical composition and fermentation characteristics of elephant grass silage with biodiesel industry co-products

The objective of this research was to evaluate the effect of three concentrations (3, 6, and 9%) of forage turnip (Raphanus sativus) and physic nut (Jatropha curcas) cakes on dry matter, crude protein, ether extract, neutral detergent fiber, acid detergent fiber, lignin, acid detergent insoluble nitrogen neutral detergent insoluble nitrogen contents, in vitro dry matter digestibility, pH values and concentrations of N-NH3 in elephant grass silages. It was used an entirely randomized design in factorial arrangement [(2x3)+1]. Experimental PVC silos were used and ensiled material was kept for 62 days. The addition of cakes increased the dry matter contents (P<0.05). The fibrous fractions were reduced (P<0.05) with the inclusion of cakes during the grass ensilage and the CP contents increased (P<0.05). The forage turnip cake provided the same pH and N-NH3 values in ideal levels and the physic nut, added to 9%, increased those values (P<0.05). IVDMD was reduced (P<0.05) when the cakes were added. These co-products can be used in small amounts for elephant grass ensilage in order to provide improvement in chemical and fermentation characteristics of the silages. Nevertheless, physic nut cake shows limitations for its use in animal feeding due to the presence of toxic compounds, making necessary studies for their identification and elimination.

Chemical Profile and Biological Potential of Non-Polar Fractions from Centroceras clavulatum (C. Agardh) Montagne (Ceramiales, Rhodophyta)

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Tungsten permanent chemical modifier for fast estimation of Se contents in soil by graphite furnace atomic absorption spectrometry

A tungsten carbide coating on the integrated platform of a transversely heated graphite atomizer was used as a modifier for the direct determination of Se in soil extracts by graphite furnace atomic absorption spectrometry. Diethylenetriaminepentaacetic acid (0.0050 mol L-1) plus ammonium hydrogencarbonate (1.0 mol L-1) extracted predominantly available inorganic selenate from soil. The formation of a large amount of carbonaceous residue inside the atomizer was avoided with a first pyrolysis step at 600 degreesC assisted by air during 30 s. For 20 muL of soil extracts delivered to the atomizer and calibration by matrix matching, an analytical curve (10.0-100 mug of L-1) with good linear correlation (r = 0.999) between integrated absorbance and analyte concentration was established. The characteristic mass was similar to63 pg of Se, and the lifetime of the tube was similar to750 firings. The limit of detection was 1.6 mug L-1, and the relative standard deviations (n = 12) were typically <4% for a soil extract containing 50 mug of L-1. The accuracy of the determination of Se was checked for soil samples by means of addition/recovery tests. Recovery data of Se added to four enriched soil samples varied from 80 to 90% and indicated an accurate method.

A Prodrug Approach to Improve the Physico-Chemical Properties and Decrease the Genotoxicity of Nitro Compounds

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Pressure-induced electrical and structural anomalies in Pb1-xCaxTiO3 thin films grown at various oxygen pressures by chemical solution route

Lead calcium titanate (Pb1-xCaxTiO3 or PCT) thin films have been thermally treated under different oxygen pressures, 10, 40 and 80 bar, by using the so-called chemical solution deposition method. The structural, morphological, dielectric and ferroelectric properties were characterized by x-ray diffraction, FT-infrared and Raman spectroscopy, atomic force microscopy and polarization-electric-field hysteresis loop measurements. By annealing at a controlled pressure of around 10 and 40 bar, well-crystallized PCT thin films were successfully prepared. For the sample submitted to 80 bar, the x-ray diffraction, Fourier transformed-infrared and Raman data indicated deviation from the tetragonal symmetry. The most interesting feature in the Raman spectra is the occurrence of intense vibrational modes at frequencies of around 747 and 820 cm(-1), whose presence depends strongly on the amount of the pyrochlore phase. In addition, the Raman spectrum indicates the presence of symmetry-breaking disorder, which would be expected for an amorphous (disorder) and mixed pyrochlore-perovskite phase. During the high-pressure annealing process, the crystallinity and the grain size of the annealed film decreased. This process effectively suppressed both the dielectric and ferroelectric behaviour. Ferroelectric hysteresis loop measurements performed on these PCT films exhibited a clear decrease in the remanent polarization with increasing oxygen pressure.

CHEMICAL MODIFICATION EFFECT on THE MECHANICAL PROPERTIES of HIPS/COCONUT FIBER COMPOSITES

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Revegetation and Soil Management Effects on Chemical Properties of a Saprolite Resulting from Deep Soil Removal

During the building of a hydroelectrical power plant at Ilha Solteira in the Parana River (Brazil), materials of a highly weathered soil Oxisol were extracted from a depth between 5 and 8 m for engineering works. This resulted in an abandoned depression area. The topsoil was not salvaged and the open pit was not backfilled, and as result vegetation hardly or not at all recovered. on the residual saprolite materials, an experimental field was established to assess different soil rehabilitation treatments. Field experiments were initiated in 1992. After soil tillage, two different crops and three different liming strategies were compared, giving six combinations. In addition, two uncropped control treatments, tilled and no-tilled, were established so that a total of eight treatments were assessed. The experimental design consisted of four randomized experimental blocks, which included a total of 32 plots with a plot area of 100 m(2). This experiment was used to study the effectiveness of the soil-reclamation treatments after a 9-year period. Soil samples were taken at three different depths (0-10, 10-20, and 20-40 cm), and they were analyzed routinely for pH, organic-matter content, and cation exchange capacity (CEC). Revegetation of the abandoned saprolite material increased soil organic-matter content and cation exchange capacity (CEC), and to some extent small differences between treatments were evidenced. Exchangeable calcium (Ca) and magnesium (Mg) recovered faster than organic-matter content. A significant linear relationship was found between organic-matter content and CEC, suggesting continued addition of organic material will further approach the value of these parameters to those levels corresponding to natural soils under "Cerrado" vegetation.

Effect of Chemical Disinfection and Accelerated Aging on Color Stability of Maxillofacial Silicone with Opacifiers

Purpose: The purpose of this study was to evaluate the color stability of MDX4-4210 maxillofacial elastomer with opacifier addition submitted to chemical disinfection and accelerated aging.Materials and Methods: Ninety specimens were obtained from Silastic MDX4-4210 silicone. The specimens were divided into three groups (n = 30): Group I: colorless, Group II: barium sulfate opacifier, Group III: titanium dioxide opacifier. Specimens of each group (n = 10) were disinfected with effervescent tablets, neutral soap, or 4% chlorhexidine gluconate. Disinfection was conducted three times a week for 2 months. Afterward, the specimens were submitted to different periods of accelerated aging. Color evaluation was carried out after 60 days (disinfection period) and after 252, 504, and 1008 hours of accelerated aging, using a reflection spectrophotometer. Color alterations were calculated by the CIE L*a*b* system. Data were analyzed by three-way ANOVA and Tukey test (alpha = 0.05).Results: Group II exhibited the lowest color change, whereas Group III the highest (p < 0.05), regardless of the chemical disinfection and accelerated aging periods.Conclusion: Opacifier addition, chemical disinfection, and accelerated aging procedures affected the color stability of the maxillofacial silicone.