Development of copper and nickel based oxide thin-films: design and fabrication of thin-film transistors

Dissertação para obtenção do Grau de Doutor em Nanotecnologia e Nanociência

Degradation of all-inkjet-printed organic thin-film transistors with TIPS-pentacene under processes applied in textile manufacturing

Printed electronics represent an alternative solution for the manufacturing of low-temperature and large area flexible electronics. The use of inkjet printing is showing major advantages when compared to other established printing technologies such as, gravure, screen or offset printing, allowing the reduction of manufacturing costs due to its efficient material usage and the direct-writing approach without requirement of any masks. However, several technological restrictions for printed electronics can hinder its application potential, e.g. the device stability under atmospheric or even more stringent conditions. Here, we study the influence of specific mechanical, chemical, and temperature treatments usually appearing in manufacturing processes for textiles on the electrical performance of all-inkjet-printed organic thin-film transistors (OTFTs). Therefore, OTFTs where manufactured with silver electrodes, a UV curable dielectric, and 6,13-bis(triisopropylsilylethynyl) pentance (TIPS-pentacene) as the active semiconductor layer. All the layers were deposited using inkjet printing. After electrical characterization of the printed OTFTs, a simple encapsulation method was applied followed by the degradation study allowing a comparison of the electrical performance of treated and not treated OTFTs. Industrial calendering, dyeing, washing and stentering were selected as typical textile processes and treatment methods for the printed OTFTs. It is shown that the all-inkjet-printed OTFTs fabricated in this work are functional after their submission to the textiles processes but with degradation in the electrical performance, exhibiting higher degradation in the OTFTs with shorter channel lengths (L=10 μm).

Study of the tightness of the metallization used on top of a thin film capacitor cell

Dissertação de mestrado integrado em Engenharia de Materiais

Effect of argon ion energy on the performance of silicon nitridemultilayer permeation barriers grown by hot-wire CVD on polymers

One of the authors (S.M.) acknowledges Direction des Relations Extérieures of Ecole Polytechnique for financial support.

Multifunctional Ti–Me (Me=Al, Cu) thin film systems for biomedical sensing devices

Ti-Me binary intermetallic thin films based on a titanium matrix doped with increasing amounts of Me (Me = Al, Cu) were prepared by magnetron sputtering (under similar conditions), aiming their application in biomedical sensing devices. The differences observed on the composition and on the micro(structural) features of the films, attributed to changes in the discharge characteristics, were correlated with the electrical properties of the intermetallic systems (Ti-Al and Ti-Cu). For the same Me exposed areas placed on the Ti target (ranging from 0.25 cm2 to 20 cm2) the Cu content increased from 3.5 at.% to 71.7 at.% in the Ti-Cu system and the Al content, in Ti-Al films, ranged from 11 to 45 at.%. The structural characterization evidenced the formation of metastable Ti-Me intermetallic phases for Al/Ti atomic ratios above 0.20 and for Cu/Ti ratios above 0.25. For lower Me concentrations, the effect of the α-Ti(Me) structure domains the overall structure. With the increase amount of the Me into Ti structure a clear trend for amorphization was observed. For both systems it was observed a significant decrease of the electrical resistivity with increasing Me/Ti atomic ratios (higher than 0.5 for Al/Ti atomic ratio and higher than 1.3 for Cu/Ti atomic ratio). Although similar trends were observed in the resistivity evolution for both systems, the Ti-Cu films presented lower resistivity values in comparison to Ti-Al system.

Flexible gastrointestinal motility pressure sensors based on aluminum thin-film strain-gauge arrays

This paper reports on an innovative approach to measuring intraluminal pressure in the upper gastrointestinal (GI) tract, especially monitoring GI motility and peristaltic movements. The proposed approach relies on thin-film aluminum strain gauges deposited on top of a Kapton membrane, which in turn lies on top of an SU-8 diaphragm-like structure. This structure enables the Kapton membrane to bend when pressure is applied, thereby affecting the strain gauges and effectively changing their electrical resistance. The sensor, with an area of 3.4 mm2, is fabricated using photolithography and standard microfabrication techniques (wet etching). It features a linear response (R2 = 0.9987) and an overall sensitivity of 2.6 mV mmHg−1. Additionally, its topology allows a high integration capability. The strain gauges’ responses to pressure were studied and the fabrication process optimized to achieve high sensitivity, linearity, and reproducibility. The sequential acquisition of the different signals is carried out by a microcontroller, with a 10-bit ADC and a sample rate of 250 Hz. The pressure signals are then presented in a user-friendly interface, developed using the Integrated Development Environment software, QtCreator IDE, for better visualization by physicians.

Flexible thin-film lithium battery

Tese de Doutoramento Programa Doutoral em Engenharia Electrónica e Computadores.

Producción de diamante por CVD (Chemical Vapour Deposition)

A fines de la década del '60 un grupo de investigadores rusos pudo obtener diamante a partir de experimentos con reacciones en fase vapor a bajas presiones de los gases envueltos en el proceso. En 1976 Derjagin et al. mostraron que la nucleación de diamante es posible sobre sustratos de Cu y en 1982 Matsumoto demuestra que la nucleación y crecimiento continuo a bajas presiones de diamante es posible sobre diversos substratos. Las especiales propiedades del diamante (D): dureza, elevado punto de fusión, inercia química, así como elevada conductividad del calor, sonido y de señales ópticas, ubican a este material como una de las prioridades de desarrollo e investigación de grupos de excelencia en el mundo entero. (...) Objetivos Generales y Específicos: El objetivo de este proyecto se basa en la construcción de un reactor para CVD (Chemical Vapour Deposition) y de los elementos auxiliares necesarios para producir diamante sintético por este método. Determinando los parámetros que controlan el proceso: mezcla de gases adecuada, temperatura de substrato, temperatura del plasma, presión parcial de los gases, vacío necesario y otros. En la primera etapa de 2 años se priorizará la puesta a punto del método, para luego pasar al estudio de las diferentes aplicaciones tecnológicas necesarias para la región. Específicamente, en el tercer año se tratará de generar diamantes como recubrimientos para herramientas de corte, así como para trapanos de velocidad, aprovechando residuos para la industria de abrasivos. Los objetivos generales no se cirscuncriben sólo al hecho de montar un reactor en laboratorio para CVD, sino una vez encontrados los parámetros que gobiernan esta técnica, producir diamante sintético para aplicaciones en la industria de herramientas de corte, micrófonos y óptica. Otro objetivo general de importancia es la formación de recursos humanos en técnicas de vacío, ingeniería de superficie y tecnología de plasma a través del personal y de los estudiantes involucrados en el proyecto, así como los participantes en cátedras del Departamento de Mecánica. En cuanto a los objetivos específicos para los dos primeros años, es preparar, construir y poner a punto un reactor de laboratorio de filamento caliente (Hot filament) por tecnología de plasma tipo CVD para obtener diamante sintético a partir de gases.

Improving Post-Discharge Medication Adherence in Patients with CVD: A Pilot Randomized Trial

Background:Effective interventions to improve medication adherence are usually complex and expensive.Objective:To assess the impact of a low-cost intervention designed to improve medication adherence and clinical outcomes in post-discharge patients with CVD.Method:A pilot RCT was conducted at a teaching hospital. Intervention was based on the four-item Morisky Medication Adherence Scale (MMAS-4). The primary outcome measure was medication adherence assessed using the eight-item MMAS at baseline, at 1 month post hospital discharge and re-assessed 1 year after hospital discharge. Other outcomes included readmission and mortality rates.Results:61 patients were randomized to intervention (n = 30) and control (n = 31) groups. The mean age of the patients was 61 years (SD 12.73), 52.5% were males, and 57.4% were married or living with a partner. Mean number of prescribed medications per patient was 4.5 (SD 3.3). Medication adherence was correlated to intervention (p = 0.04) and after 1 month, 48.4% of patients in the control group and 83.3% in the intervention group were considered adherent. However, this difference decreased after 1 year, when adherence was 34.8% and 60.9%, respectively. Readmission and mortality rates were related to low adherence in both groups.Conclusion:The intervention based on a validated patient self-report instrument for assessing adherence is a potentially effective method to improve adherent behavior and can be successfully used as a tool to guide adherence counseling in the clinical visit. However, a larger study is required to assess the real impact of intervention on these outcomes.

Wärmeübergang bei der Sprühkühlung mit intermittierenden Sprays im Film- und Übergangssiedebereich

Magdeburg, Univ., Fak. für Verfahrens- und Systemtechnik, Diss., 2015

The diamond : a study in Chinese and Hellenistic folk-lore / by Berthold Laufer --

v.15:no.1(1915)

Tomato response to a high light transmission greenhouse film

Increasing greenhouse light transmission has a positive effect not only in Northern latitudes but in Mediterranean countries as well. A greenhouse, H2, with a tetrafluoroethylene copolymer 60 microns film, (Asahi Glass company, Aflex) characterised by its high light transmission and durability was compared to another greenhouse with a co-extruded film considered as a control, H1. Tomato crop response to the increase in light during winter and summer with high temperature and light was evaluated. Light transmission in H2 remained very high in spite of the observed dust accumulation and the low angle of incidence of the winter solar radiation. Transmissivity was clearly higher for H2 (81 to 83 % throughout the season) than in the control (around 63 %). The rest of the climatic parameters were similar in both greenhouses, either in the winter or in the summer evaluations. In spite of the high solar radiation in H2, the summer temperature could be maintained at the desired levels by using evaporative cooling. Accumulated tomato yield and quality was better in the H2 greenhouse (15 % more for the winter crop and 27% more for the summer crop). Fruit size was bigger in the winter crop. As an overall conclusion, the use of high light transmissive films in Mediterranean areas is very convenient for many vegetable crops. This is valid not only in winter but in summer, provided the greenhouse has good ventilation or evaporative cooling to overcome the increase in sensible heat caused by this increase in light..