Avaliação nutricional de silagem de restos culturais de abacaxi pérola

Pós-graduação em Zootecnia - FCAV

Influence of cellulose nanofibrils on soft and hard segments of polyurethane/cellulose nanocomposites and effect of humidity on their mechanical properties

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Different sources of forage with crude glycerin in diets with higher percentage of concentrate to beef cattle

Pós-graduação em Zootecnia - FCAV

Fontes de ácidos graxos insaturados na alimentação de vacas leiteiras no período seco

Pós-graduação em Zootecnia - FCAV

Parâmetros ruminais e produtivos de cabras alimentadas com raspa de mandioca em substituição ao milho

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Chemical composition and in vitro digestibility of fresh sugarcane hydrolysed with calcium oxide (CaO)

The objective was to evaluate the chemical composition and in vitro digestibility of sugarcane hydrolysed with increasing doses of calcium oxide and varying air exposure times. A completely randomised, split plot design was used; the doses were allocated to the plots, and the air exposure times were allocated to the subplots, with four repetitions. The data underwent analysis of variance and were laid out according to the effect of the treatment on the components of polynomial regressions, and evaluated at the 5% probability. The increase in the dosage negatively affected the quantities of neutral-detergent fibre (NDF), acid-detergent fibre (ADF), lignin (LIG), total carbohydrates (TC), cellulose (CEL), crude protein (CP), and ether extract (EE); and positively affected the quantities of non-fibrous carbohydrates (NFC) and mineral matter (MM). The addition of calcium oxide improved the in vitro digestible dry matter (IVDMD) coefficients and was able to keep up to 72 hours. The in vitro digestibility of the neutral-detergent fibre (IVDNDF) and of the acid-detergent fibre (IVDADF) coefficients decreased when calcium oxide was added. Calcium oxide has the ability to hydrolyse the fibrous fraction and conserve chopped sugarcane. Doses of 0.5 and 1.0% lime exhibited similar results to those achieved at higher doses; therefore, higher doses are not required in the hydrolyses of sugarcane. Over time, the sugarcane deteriorates, but this deterioration is reduced by the addition of calcium oxide.

Frequencies of virulence genes and pulse field gel electrophoresis fingerprints in Escherichia coli isolates from canine pyometra

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Chemical and bromatological characteristics of elephant grass silages with the addition of dried cashew stalk

Este trabalho foi conduzido para avaliar o valor nutritivo de silagens de capim-elefante (Pennisetum purpureum, Schum.) com 0, 4, 8, 12 e 16% de pedúnculo de caju (Anacardium occidentale L.) desidratado, com base na matéria natural. Utilizou-se o delineamento inteiramente casualizado com quatro repetições. Como silos experimentais, foram utilizados tambores plásticos de 210 L. Determinaram-se a composição nutricional, os valores de pH e os teores de nitrogênio amoniacal, ácido lático, acético, propiônico e butírico. A inclusão de pedúnculo de caju desidratado na ensilagem de capim-elefante promoveu aumento das concentrações de matéria seca (MS), proteína bruta (PB), extrato etéreo (EE), carboidratos não-fibrosos (CNF), nitrogênio insolúvel em detergente neutro (NIDN, % do N total), nitrogênio insolúvel em detergente ácido (NIDA, % do N total), pH e ácidos lático e propiônico. Por outro lado, os teores de FDN, FDA, hemicelulose, N-NH3 (% do N total) e ácido butírico diminuíram de forma linear conforme aumentaram os níveis do subproduto na ensilagem. O pedúnculo de caju desidratado não influenciou os teores de carboidratos totais e ácido acético das silagens. Esse subproduto pode ser ensilado com o capim-elefante até o nível de 16%, uma vez que aumenta os teores de PB e CNF e reduz os teores de FDN e FDA, melhorando o padrão de fermentação das silagens.

Determinação da relação de novo biomarcador (IMP3) no carcinoma de nasofaringe

Pós-graduação em Patologia - FMB

Prevalence of avian pathogenic Escherichia coli (APEC) clone harboring sfa gene in Brazil

Escherichia coli sfa+ strains isolated from poultry were serotyped and characterized by polymerase chain reaction (PCR) and amplified fragment length polymorphism (AFLP). Isolates collected from 12 Brazilian poultry farms mostly belonged to serogroup O6, followed by serogroups O2, O8, O21, O46, O78, O88, O106, O111, and O143. Virulence genes associated were: iuc 90%, fim 86% neuS 60%, hly 34%, tsh 28%, crl/csg 26%, iss 26%, pap 18%, and 14% cnf. Strains from the same farmpresented more than one genotypic pattern belonging to different profiles in AFLP. AFLP showed a clonal relation between Escherichia coli sfa+ serogroup O6. The virulence genes found in these strains reveal some similarity with extraintestinal E. coli (ExPEC), thus alerting for potential zoonotic risk.

Colibacillosis in lambs is associated to type I heat-stable enterotoxin in a farm in Sao Paulo State, Brazil

Twenty seven (48.2%) culture supernatants of 56 Escherichia coli isolated from diarrheic lamb feces (7 to 10 days old) in Sao Paulo State, Brazil, presented positive results to suckling mice assay (fluid accumulation) but none caused cytopathic effects on Vero and CHO cells, indicating that these strains did not produced LT or VT toxins. PCR assays showed that these 27 E. coli strains harbored estA, that codifies for STa, but not for stx1, stx2 or cnf genes. The positive STa strains were checked for genes that codify for F41, F17 and K99 fimbriae, wich are considered colonization factors in ETEC. Only F17 was detect in two samples (7.4%). Twelve of 27 STa positive carried hlyA gene and presented hemolytic activity in blood Agar. Presence of rotavirus was not detected among the diarrheic feces. These data suggests that STa must be an important diarrheagenic factor to small ruminants in Sao Paulo State.

Crittoanalisi Logica di DES

La crittografia ha sempre rivestito un ruolo primario nella storia del genere umano, dagli albori ai giorni nostri, e il periodo in cui viviamo non fa certo eccezione. Al giorno d'oggi, molti dei gesti che vengono compiuti anche solo come abitudine (operazioni bancarie, apertura automatica dell'auto, accedere a Facebook, ecc.), celano al loro interno la costante presenza di sofisticati sistemi crittografici. Proprio a causa di questo fatto, è importante che gli algoritmi utilizzati siano in qualche modo certificati come ragionevolmente sicuri e che la ricerca in questo campo proceda costantemente, sia dal punto di vista dei possibili nuovi exploit per forzare gli algoritmi usati, sia introducendo nuovi e sempre più complessi sistemi di sicurezza. In questa tesi viene proposto una possibile implementazione di un particolare tipo di attacco crittoanalitico, introdotto nel 2000 da due ricercatori dell'Università "La Sapienza" di Roma, e conosciuto come "Crittoanalisi Logica". L'algoritmo su cui è incentrato il lavoro è il Data Encryption Standard (DES), ostico standard crittografico caduto in disuso nel 1999 a causa delle dimensioni ridotte della chiave, seppur tuttora sia algebricamente inviolato. Il testo è strutturato nel seguente modo: il primo capitolo è dedicato ad una breve descrizione di DES e della sua storia, introducendo i concetti fondamentali con cui si avrà a che fare per l'intera dissertazione Nel secondo capitolo viene introdotta la Crittoanalisi Logica e viene fornita una definizione della stessa, accennando ai concetti matematici necessari alla comprensione dei capitoli seguenti. Nel capitolo 3 viene presentato il primo dei due software sviluppati per rendere possibile l'attuazione di questo attacco crittoanalitico, una libreria per la rappresentazione e la manipolazione di formule logiche scritta in Java. Il quarto ed ultimo capitolo descrive il programma che, utilizzando la libreria descritta nel capitolo 3, elabora in maniera automatica un insieme di proposizioni logiche semanticamente equivalenti a DES, la cui verifica di soddisfacibilità, effettuata tramite appositi tools (SAT solvers) equivale ad effettuare un attacco di tipo known-plaintext su tale algoritmo.

Pore structure and column efficiency of silica monoliths in high performance liquid chromatography (HPLC)

Five different methods were critically examined to characterize the pore structure of the silica monoliths. The mesopore characterization was performed using: a) the classical BJH method of nitrogen sorption data, which showed overestimated values in the mesopore distribution and was improved by using the NLDFT method, b) the ISEC method implementing the PPM and PNM models, which were especially developed for monolithic silicas, that contrary to the particulate supports, demonstrate the two inflection points in the ISEC curve, enabling the calculation of pore connectivity, a measure for the mass transfer kinetics in the mesopore network, c) the mercury porosimetry using a new recommended mercury contact angle values. rnThe results of the characterization of mesopores of monolithic silica columns by the three methods indicated that all methods were useful with respect to the pore size distribution by volume, but only the ISEC method with implemented PPM and PNM models gave the average pore size and distribution based on the number average and the pore connectivity values.rnThe characterization of the flow-through pore was performed by two different methods: a) the mercury porosimetry, which was used not only for average flow-through pore value estimation, but also the assessment of entrapment. It was found that the mass transfer from the flow-through pores to mesopores was not hindered in case of small sized flow-through pores with a narrow distribution, b) the liquid penetration where the average flow-through pore values were obtained via existing equations and improved by the additional methods developed according to Hagen-Poiseuille rules. The result was that not the flow-through pore size influences the column bock pressure, but the surface area to volume ratio of silica skeleton is most decisive. Thus the monolith with lowest ratio values will be the most permeable. rnThe flow-through pore characterization results obtained by mercury porosimetry and liquid permeability were compared with the ones from imaging and image analysis. All named methods enable a reliable characterization of the flow-through pore diameters for the monolithic silica columns, but special care should be taken about the chosen theoretical model.rnThe measured pore characterization parameters were then linked with the mass transfer properties of monolithic silica columns. As indicated by the ISEC results, no restrictions in mass transfer resistance were noticed in mesopores due to their high connectivity. The mercury porosimetry results also gave evidence that no restrictions occur for mass transfer from flow-through pores to mesopores in the small scaled silica monoliths with narrow distribution. rnThe prediction of the optimum regimes of the pore structural parameters for the given target parameters in HPLC separations was performed. It was found that a low mass transfer resistance in the mesopore volume is achieved when the nominal diameter of the number average size distribution of the mesopores is appr. an order of magnitude larger that the molecular radius of the analyte. The effective diffusion coefficient of an analyte molecule in the mesopore volume is strongly dependent on the value of the nominal pore diameter of the number averaged pore size distribution. The mesopore size has to be adapted to the molecular size of the analyte, in particular for peptides and proteins. rnThe study on flow-through pores of silica monoliths demonstrated that the surface to volume of the skeletons ratio and external porosity are decisive for the column efficiency. The latter is independent from the flow-through pore diameter. The flow-through pore characteristics by direct and indirect approaches were assessed and theoretical column efficiency curves were derived. The study showed that next to the surface to volume ratio, the total porosity and its distribution of the flow-through pores and mesopores have a substantial effect on the column plate number, especially as the extent of adsorption increases. The column efficiency is increasing with decreasing flow through pore diameter, decreasing with external porosity, and increasing with total porosity. Though this tendency has a limit due to heterogeneity of the studied monolithic samples. We found that the maximum efficiency of the studied monolithic research columns could be reached at a skeleton diameter of ~ 0.5 µm. Furthermore when the intention is to maximize the column efficiency, more homogeneous monoliths should be prepared.rn

Innovative processes for syngas production

The research of new advanced processes for syngas production is a part of a European project for the production of a new Gas to Liquid Process (NextGTL). The crucial points in the production of GTL process are the energy required for the air separation used in autothermal reforming or the heat required for steam reforming and the efficiency in carbon utilization. Therefore a new multistep oxy-reforming process scheme was developed at lower temperature with intermediate H2 membrane separation to improve the crucial parameter. The process is characterized by a S/C of 0.7 and O2/C of 0.21 having a smoothed temperature profile in which kinetic regime is easily obtained. Active catalysts for low temperature oxy-reforming process have been studied working at low pressure to discriminate among the catalyst and at high pressure to prove it on industrial condition. It allows the selection of the Rh as active phase among single and bimetallic VIII group metal. The study of the matrix composition and thermal treatment has been carried out on Rh-Mg/Al hydrotalcite selected as reference catalyst. The research to optimize the catalyst lead to enhanced performances through the identification of a limitation of the Rh reduction from the oxides matrix as key point to increase the Rh performances. The Rh loading have been studied to allow the catalyst scale up for pilot process in Chieti in a shape of Rh-HT on honeycomb ceramic material. The developed catalyst has enhanced methane conversion in a inch diameter monolith reactor if compared with the semi-industrial catalyst chosen in the project as the best reference.

Modeling of diesel particulate filter filtration and regeneration for transient driving schedules

Due to their high thermal efficiency, diesel engines have excellent fuel economy and have been widely used as a power source for many vehicles. Diesel engines emit less greenhouse gases (carbon dioxide) compared with gasoline engines. However, diesel engines emit large amounts of particulate matter (PM) which can imperil human health. The best way to reduce the particulate matter is by using the Diesel Particulate Filter (DPF) system which consists of a wall-flow monolith which can trap particulates, and the DPF can be periodically regenerated to remove the collected particulates. The estimation of the PM mass accumulated in the DPF and total pressure drop across the filter are very important in order to determine when to carry out the active regeneration for the DPF. In this project, by developing a filtration model and a pressure drop model, we can estimate the PM mass and the total pressure drop, then, these two models can be linked with a regeneration model which has been developed previously to predict when to regenerate the filter. There results of this project were: 1 Reproduce a filtration model and simulate the processes of filtration. By studying the deep bed filtration and cake filtration, stages and quantity of mass accumulated in the DPF can be estimated. It was found that the filtration efficiency increases faster during the deep-bed filtration than that during the cake filtration. A “unit collector” theory was used in our filtration model which can explain the mechanism of the filtration very well. 2 Perform a parametric study on the pressure drop model for changes in engine exhaust flow rate, deposit layer thickness, and inlet temperature. It was found that there are five primary variables impacting the pressure drop in the DPF which are temperature gradient along the channel, deposit layer thickness, deposit layer permeability, wall thickness, and wall permeability. 3 Link the filtration model and the pressure drop model with the regeneration model to determine the time to carry out the regeneration of the DPF. It was found that the regeneration should be initiated when the cake layer is at a certain thickness, since a cake layer with either too big or too small an amount of particulates will need more thermal energy to reach a higher regeneration efficiency. 4 Formulate diesel particulate trap regeneration strategies for real world driving conditions to find out the best desirable conditions for DPF regeneration. It was found that the regeneration should be initiated when the vehicle’s speed is high and during which there should not be any stops from the vehicle. Moreover, the regeneration duration is about 120 seconds and the inlet temperature for the regeneration is 710K.