Branding and Marketing Communications of Lifestyle Prescription Drugs in a Strict Legislative Environment

This thesis discusses the different possibilities to brand and promote a patented prescription lifestyle drug through different marketing communications practices. This thesis aims in explaining how branding procedures can be built in circumstances, where the legislative environment is strickt and furthermore, the environment consists of both B-to-B and B-to-C market characteristics simultaneously.

The oxygenation in biological wastewater treatment of pulp and paper industry

The UPM-Kymmene Oyj Pietarsaari pulp and paper Mill biological wastewater treatment plant was built in the 1980's and the plant has been in use ever since. During the past years there have been problems with deviations. The wastewater treatment plant needs update, especially the aeration basin, where the old surface aerators cannot produce enough mixing and indroduce oxygen enough to the wastewater. In this thesis how extra aeration with oxygen affects the wastewater treatment plant effluent was studied. In the literature part the main focus is in aeration devices, which can be used in biological wastewater treatment. The target is to compare different kind of aerators, which are suitable for pulp and paper wastewater treatment. Studies show, that EDI-aerators are commonly used and also most suitable. In the experimental part, the focus is on the Pietarsaari Mills wastewater treatment plant and oxygen aeration during autumn 2008. This thesis presents the results of the trial run. Studies show, that extra oxygen devices can produce lot a of mixing and the oxygenation capacity was more than what the micro-organisms needed. The effect on sludge quality could not been seen during the trial runs.

Determination of sulfur in diesel using ATR/FTIR and multivariate calibration

The aim of this present work was to provide a more fast, simple and less expensive to analyze sulfur content in diesel samples than by the standard methods currently used. Thus, samples of diesel fuel with sulfur concentrations varying from 400 and 2500 mgkg-1 were analyzed by two methodologies: X-ray fluorescence, according to ASTM D4294 and by Fourier transform infrared spectrometry (FTIR). The spectral data obtained from FTIR were used to build multivariate calibration models by partial least squares (PLS). Four models were built in three different ways: 1) a model using the full spectra (665 to 4000 cm-1), 2) two models using some specific spectrum regions and 3) a model with variable selected by classic method of variable selection stepwise. The model obtained by variable selection stepwise and the model built with region spectra between 665 and 856 cm-1 and 1145 and 2717 cm-1 showed better results in the determination of sulfur content.

Modelling of calciner in post-combustion carbon capture process

Climate change has given an impetus to research and developed new technologies to reduce significantly carbon dioxide emissions in energy production in the developed countries. The major pollution source, fossil fuels, will be used as an energy source for many decades, which provides the demand for carbon capture and storage technologies. Over recent years many new technologies has been developed and one of the most promising is calcium-looping in post-combustion carbon capture process, which use carbonation-calcination cycle to capture carbon dioxide from the flue gas of a combustion process. First pilot plant for calcium-looping process has been built in Oviedo, Spain. In this study, a three-dimensional model has been created for the calciner, which is one of the two fluidized bed reactors needed for the process. The calciner is a regenerator where the captured carbon dioxide is removed from the calcium material and then collected after the reactor. Thesis concentrates in creating the calciner 3D-model frame with CFB3D-program and testing the model with two different example cases. Used input parameters and calciner geometry are Oviedo pilot plant design parameters. The calculation results give information about the process and show that pilot plant calciner should perform as planned. This Master’s Thesis is done in participation to EU FP7 project CaOling.

Service innovation development and knowledge integration practices - a comparative case study on KIBS sector

Academic research on services and innovations on services has significantly grown during recent years. So far research concerning management of knowledge intensive work on service development activities is very limited. The objective of this study was to examine knowledge integration practices that support service innovation development and to the best of knowledge such studies have not been previously published in academic literature. In the theoretical part of the study a review of state‐of‐the‐art literature was conducted, research gap was indicated and a framework for analysis was built. In the empirical part an explorative comparative multi‐case study was carried out in KIBS sector. Four companies were selected and four service development projects were inspected. The service development activities and knowledge integration practices were identified. The cases were carefully compared and results formed. The empirical results indicated that service innovation development is partly linear and partly incremental flow of activities where knowledge integration practices have important role supporting the planning and execution of tasks. Knowledge integration practices supporting planning and workshops are close interaction, interpretation, project planning and sequencing of work tasks. The identified knowledge integration practices supporting building service solution were careful role and competence management, routines and common knowledge. The main implication is that to manage knowledge intensive service innovation development a firm should carefully develop and choose relevant knowledge integration practices to support the service development activities.

Covalidation of Integral Transforms and Method of Lines in Nonlinear Convection-Diffusion with Mathematica

The Mathematica system (version 4.0) is employed in the solution of nonlinear difusion and convection-difusion problems, formulated as transient one-dimensional partial diferential equations with potential dependent equation coefficients. The Generalized Integral Transform Technique (GITT) is first implemented for the hybrid numerical-analytical solution of such classes of problems, through the symbolic integral transformation and elimination of the space variable, followed by the utilization of the built-in Mathematica function NDSolve for handling the resulting transformed ODE system. This approach ofers an error-controlled final numerical solution, through the simultaneous control of local errors in this reliable ODE's solver and of the proposed eigenfunction expansion truncation order. For covalidation purposes, the same built-in function NDSolve is employed in the direct solution of these partial diferential equations, as made possible by the algorithms implemented in Mathematica (versions 3.0 and up), based on application of the method of lines. Various numerical experiments are performed and relative merits of each approach are critically pointed out.

Potential and Challenges of Analog Reconfigurable Computation in Modern and Future CMOS

In this work, the feasibility of the floating-gate technology in analog computing platforms in a scaled down general-purpose CMOS technology is considered. When the technology is scaled down the performance of analog circuits tends to get worse because the process parameters are optimized for digital transistors and the scaling involves the reduction of supply voltages. Generally, the challenge in analog circuit design is that all salient design metrics such as power, area, bandwidth and accuracy are interrelated. Furthermore, poor flexibility, i.e. lack of reconfigurability, the reuse of IP etc., can be considered the most severe weakness of analog hardware. On this account, digital calibration schemes are often required for improved performance or yield enhancement, whereas high flexibility/reconfigurability can not be easily achieved. Here, it is discussed whether it is possible to work around these obstacles by using floating-gate transistors (FGTs), and analyze problems associated with the practical implementation. FGT technology is attractive because it is electrically programmable and also features a charge-based built-in non-volatile memory. Apart from being ideal for canceling the circuit non-idealities due to process variations, the FGTs can also be used as computational or adaptive elements in analog circuits. The nominal gate oxide thickness in the deep sub-micron (DSM) processes is too thin to support robust charge retention and consequently the FGT becomes leaky. In principle, non-leaky FGTs can be implemented in a scaled down process without any special masks by using “double”-oxide transistors intended for providing devices that operate with higher supply voltages than general purpose devices. However, in practice the technology scaling poses several challenges which are addressed in this thesis. To provide a sufficiently wide-ranging survey, six prototype chips with varying complexity were implemented in four different DSM process nodes and investigated from this perspective. The focus is on non-leaky FGTs, but the presented autozeroing floating-gate amplifier (AFGA) demonstrates that leaky FGTs may also find a use. The simplest test structures contain only a few transistors, whereas the most complex experimental chip is an implementation of a spiking neural network (SNN) which comprises thousands of active and passive devices. More precisely, it is a fully connected (256 FGT synapses) two-layer spiking neural network (SNN), where the adaptive properties of FGT are taken advantage of. A compact realization of Spike Timing Dependent Plasticity (STDP) within the SNN is one of the key contributions of this thesis. Finally, the considerations in this thesis extend beyond CMOS to emerging nanodevices. To this end, one promising emerging nanoscale circuit element - memristor - is reviewed and its applicability for analog processing is considered. Furthermore, it is discussed how the FGT technology can be used to prototype computation paradigms compatible with these emerging two-terminal nanoscale devices in a mature and widely available CMOS technology.

Flow in porous media of oil-water systems

Fluid flow behaviour in porous media is a conundrum. Therefore, this research is focused on filtration-volumetric characterisation of fractured-carbonate sediments, coupled with their proper simulation. For this reason, at laboratory rock properties such as pore volume, permeability and porosity are measured, later phase permeabilities and oil recovery in function of flow rate are assessed. Furthermore, the rheological properties of three oils are measured and analysed. Finally based on rock and fluid properties, a model using COMSOL Multiphysics is built in order to compare the experimental and simulated results. The rock analyses show linear relation between flow rate and differential pressure, from which phase permeabilities and pressure gradient are determined, eventually the oil recovery under low and high flow rate is established. In addition, the oils reveal thixotropic properties as well as non-Newtonian behaviour described by Bingham model, consequently Carreau viscosity model for the used oil is given. Given these points, the model for oil and water is built in COMSOL Multiphysics, whereupon successfully the reciprocity between experimental and simulated results is analysed and compared. Finally, a two-phase displacement model is elaborated.

New threats - old routines : bureaucratic adaptability in the security policy environment

Within the framework of state security policy, the focus of this dissertation are the relations between how new security threats are perceived and the policy planning and bureaucratic implementation that are designed to address them. In addition, this thesis explores and studies some of the inertias that might exist in the core of the state apparatus as it addresses new threats and how these could be better managed. The dissertation is built on five thematic and interrelated articles highlighting different aspects of when new significant national security threats are detected by different governments until the threats on the policy planning side translate into protective measures within the society. The timeline differs widely between different countries and some key aspects of this process are also studied. One focus concerns mechanisms for adaptability within the Intelligence Community, another on the policy planning process within the Cabinet Offices/National Security Councils and the third focus is on the planning process and how policy is implemented within the bureaucracy. The issue of policy transfer is also analysed, revealing that there is some imitation of innovation within governmental structures and policies, for example within the field of cyber defence. The main findings of the dissertation are that this context has built-in inertias and bureaucratic seams found in most government bureaucratic machineries. As much of the information and planning measures imply security classification of the transparency and internal debate on these issues, alternative assessments become limited. To remedy this situation, the thesis recommends ways to improve the decision-making system in order to streamline the processes involved in making these decisions. Another special focus of the thesis concerns the role of the public policy think tanks in the United States as an instrument of change in the country’s national security decision-making environment, which is viewed from the perspective as being a possible source of new ideas and innovation. The findings in this part are based on unique interviews data on how think tanks become successful and influence the policy debate in a country such as the United States. It appears clearly that in countries such as the United States think tanks smooth the decision making processes, and that this model with some adaptations also might be transferrable to other democratic countries.

Mémoires de Lekain , précédés de réflexions sur cet auteur et sur l'art théâtral, par F. Talma

Comprend : Quelques réflexions sur Lekain et sur l'art théâtral

Welland County Records, 1961-1989

The origins of the Welland County Fair date back to the founding of the County of Welland in 1852. A provincial charter was issued in 1853 to create the Welland County Agricultural Society that was to operate the Fair. In 1970, the Welland County Fair became the Niagara Regional Exhibition, and the Society became known as the Niagara Regional Agriculture Society. The Society seeks to “encourage interest, promote improvements in and advance the standards of agriculture, domestic industry and rural life”. The Welland Festival of Arts was developed in 1986 in order to revitalize the town’s economy. An “outdoor art gallery” was created by painting murals on buildings that depicted the town’s heritage, a concept successfully adopted by the town of Chemainus, B.C. The first mural was completed in the summer of 1988, and by 1991 there were a total of 28 murals around the city. The endeavour proved successful: in the years that followed the creation of the Festival, two new hotels were constructed, a third was expanded, and there was an addition to the Seaway Mall to accommodate the increased tourist traffic. Optimist International is a non-profit organization that strives to “bring out the best in kids” . The first Canadian club was formed in Toronto in 1924. The Welland branch of the Optimist Club was founded in 1937. The first Welland County General Hospital opened in 1908. As the population increased, it became necessary to expand the existing facilities. Additions were made to the original structure with an East wing in 1930 and a children’s ward in 1931. However, in the 1950’s, the hospital was operating beyond optimum capacity and the need for a larger facility was clear. It was decided that a new hospital would be built, which opened in April 1960. The new hospital had 259 beds and 51 bassinets. Further additions were made in 1967 and 1978. The County of Welland was formed in 1850 when it was officially separated from Lincoln County, however, the two counties continued to operate together until 1856 when a new County building and jail for Welland County were completed. That same year, the first meeting of the Council of the Corporation of Welland County took place. The final meeting of the Council took place on December 18, 1969. The following year, the County of Welland merged with Lincoln County to form the Regional Municipality of Niagara. The Welland Mills in Thorold, Ont., was built in 1846-1847 by Jacob Keefer and is thought to have been one of the largest flour mills in Upper Canada. Ownership of the mill changed several times over the years and previous owners include the Howland family, the Hedley Shaw Milling Company and the Maple Leaf Milling Company. In 1986, the building received a heritage plaque from the Ontario Heritage Foundation, an agency of the Ontario Ministry of Culture and Recreation. At this time, the mill was no longer in operation and was being used for storage by Fraser, Inc. By 2006, the dilapidated building had been redeveloped into18 apartments and 2 floors of commercial space, while maintaining many heritage features. The building is currently known as the Welland Mills Centre.

Mindfulness: An Ancient Wisdom for the Reconceptualisation of Modern Education in the Complex World

Exploring the new science of emergence allows us to create a very different classroom than how the modern classroom has been conceptualised under the mentality of efficiency and output. Working on the whole person, and not just the mind, we see a shift from the epistemic pillars of truth to more ontological concerns as regards student achievement in our post-Modern and critical discourses. It is important to understand these shifts and how we are to transition our own perception and mentality not only in our research methodologies but also our approach to conceptualisations of issues in education and sustainability. We can no longer think linearly to approach complex problems or advocate for education and disregard our interconnectedness insofar as it enhances our children’s education. We must, therefore, contemplate and transition to a world that is ecological and not mechanical, complex and not complicated—in essence, we must work to link mind-body with self-environment and transcend these in order to bring about an integration toward a sustainable future. A fundamental shift in consciousness and perception may implicate our nature of creating dichotomous entities in our own microcosms, yet postmodern theorists assume, a priori, that these dualities can be bridged in naturalism alone. I, on the other hand, embrace metaphysics to understand the implicated modern classroom in a hierarchical context and ask: is not the very omission of metaphysics in postmodern discourse a symptom from an education whose foundation was built in its absence? The very dereliction of ancient wisdom in education is very peculiar indeed. Western mindfulness may play a vital component in consummating pragmatic idealism, but only under circumstances admitting metaphysics can we truly transcend our limitations, thereby placing Eastern Mindfulness not as an ecological component, but as an ecological and metaphysical foundation.

Sketch of the ship "Jane C. Woodruff"

A black and white copy of a sketch of the ship "Jane C. Woodruff". This appears to have been in a scrapbook. There is a slight tear which affects the picture slightly. [The Jane C. Woodruff was a barquentine ship built in St. Catharines in 1866 by Lewis Shikeluna. The ship belonged to John Battle who was an associate of Samuel D. Woodruff. She was named in honour of Samuel and his wife, Jane Caroline. She originated as a square timber trade boat before being converted into a 3 masted schooner. She collided with the "Mary Battle" in a snow squall in Georgian Bay. The ship passed out of existence in 1902].

Letter to S.D. Woodruff regarding a resolution passed that the engineer be requested to examine the fence built by the contractors alongside of the Henry Vandenburgh Farm

Letter to S.D. Woodruff regarding a resolution passed that the engineer be requested to examine the fence built by the contractors alongside of the Henry Vandenburgh Farm and report to the secretary as to whether this is a lawful fence, completed according to Williams’ contract. This is signed by Duncan McFarland, president. There is a reply written by S.D. Woodruff at the bottom of the letter stating that the fence is not built in accordance with the contract, Dec. 18, 1856.

La mise en exposition des œuvres d'art spoliées par les nazis : étude de cas de l'exposition de la collection de Jacques Goudstikker

Pour respecter les droits d'auteur, la version électronique de ce mémoire a été dépouillée de ses documents visuels et audiovisuels. La version intégrale du mémoire a été déposée au Service de la gestion des documents et des archives de l'Université de Montréal.