Controle ativo de vibração em estruturas inteligentes utilizando um controlador por modos deslizantes com compensação difusa

Smart structures and systems have the main purpose to mimic living organisms, which are essentially characterized by an autoregulatory behavior. Therefore, this kind of structure has adaptive characteristics with stimulus-response mechanisms. The term adaptive structure has been used to identify structural systems that are capable of changing their geometry or physical properties with the purpose of performing a specific task. In this work, a sliding mode controller with fuzzy inference is applied for active vibration control in an SMA two-bar truss. In order to obtain a simpler controller, a polynomial model is used in the control law, while a more sophisticated version, which presents close agreement with experimental data, is applied to describe the SMA behavior of the structural elements. This system has a rich dynamic response and can easily reach a chaotic behavior even at moderate loads and frequencies. Therefore, this approach has the advantage of not only obtaining a simpler control law, but also allows its robustness be evidenced. Numerical simulations are carried out in order to demonstrate the control system performance.

Realizzazione e collaudo di un sensore di ozono controllato da Arduino

Nell’ambito della sterilizzazione da agenti patogeni, l’ozono riveste un ruolo fondamentale grazie al suo grande potere ossidante ed è di fondamentale importanza misurare quanto ozono viene prodotto mediante una scarica DBD. Scopo di questa tesi è stato quello di realizzare un sensore dedicato alla misurazione della concentrazione di ozono, controllato da Arduino Uno. Il setup realizzato risulta economico, facilmente trasportabile e flessibile in quanto è utilizzabile in diverse modalità: è possibile salvare i dati tramite Arduino per elaborarli successivamente; permette di collegare l’uscita all’oscilloscopio per monitorare i segnali elettrici nel tempo; consente di leggere la concentrazione di ozono misurata real-time su display lcd. Infine sono state effettuati dei confronti tra il setup attualmente presente in laboratorio e il setup realizzato, e i risultati sono stati soddisfacenti.

Diseño e implementación de un seguidor solar empleando un controlador PID con modo deslizante

Tesis (Ingeniero(a) Eléctrico).--Universidad de La Salle. Facultad de Ingeniería. Programa de Ingeniería Eléctrica, 2014

Automatização de um dinamômetro hidráulico para ensaios de motores de combustão interna

Dissertação (mestrado)—Universidade de Brasília, Faculdade de Tecnologia, Departamento de Engenharia Mecânica, 2015.

SURI: Controlador MIDI por medio de un teclado de computador

El presente artículo narra las experiencias del desarrollo de Suri, un programa informático que permite enviar información MIDI a otros programas por medio del teclado del computador y combina las características lingüísticas de un editor de texto con elementos tecnológicos y musicales -- Del mismo modo, relata la forma en la que se conectó el desarrollo de este programa con la búsqueda de nuevas herramientas para la composición musical y describe sus diversas funciones y generalidades técnicas

Moedor de Pixels : interfaces, interações e audiovisual

Dissertação (mestrado)—Universidade de Brasília, Instituto de Artes, Programa de Pós-Graduação em Arte, 2016.

Desenvolvimento de sistemas embarcados para redes de sensores e atuadores sem fio aplicadas em unidades de elevação de petróleo do tipo Plunger-Lift

The Wireless Sensor Networks (WSN) methods applied to the lifting of oil present as an area with growing demand technical and scientific in view of the optimizations that can be carried forward with existing processes. This dissertation has as main objective to present the development of embedded systems dedicated to a wireless sensor network based on IEEE 802.15.4, which applies the ZigBee protocol, between sensors, actuators and the PLC (Programmable Logic Controller), aiming to solve the present problems in the deployment and maintenance of the physical communication of current elevation oil units based on the method Plunger-Lift. Embedded systems developed for this application will be responsible for acquiring information from sensors and control actuators of the devices present at the well, and also, using the Modbus protocol to make this network becomes transparent to the PLC responsible for controlling the production and delivery information for supervisory SISAL

Diseño y uso de una paleta háptica para prácticas de teleoperación con simulink

En este artículo se presenta el uso de dispositivos de realimentación de fuerzas de un grado de libertad como herramienta para el desarrollo de aplicaciones docentes en asignaturas de teleoperación y telerrobótica, con el objetivo de disponer de una interfaz física que pueda ser utilizada como equipo de prácticas. Estos dispositivos, conocidos como haptic paddle, ya han sido probados satisfactoriamente para aplicaciones educativas de modelado y simulación de sistemas, ntroducción a los haptics e ingeniería de control en diversas Universidades. Para el desarrollo de los experimentos que se muestran en este artículo se han utilizado dos dispositivos haptic paddle con un controlador basado en Arduino y fabricados mediante tecnologías aditivas de impresión 3D. Gracias a los sensores de fuerza y posición incorporados se pueden implementar esquemas bilaterales de teleoperación de posicón-posición y fuerza-posición.

Controle aplicado a poços com método de elevação e bombeio centrífugo submerso

The Electrical Submersible Pumping is an artificial lift method for oil wells employed in onshore and offshore areas. The economic revenue of the petroleum production in a well depends on the oil flow and the availability of lifting equipment. The fewer the failures, the lower the revenue shortfall and costs to repair it. The frequency with which failures occur depends on the operating conditions to which the pumps are submitted. In high-productivity offshore wells monitoring is done by operators with engineering support 24h/day, which is not economically viable for the land areas. In this context, the automation of onshore wells has clear economic advantages. This work proposes a system capable of automatically control the operation of electrical submersible pumps, installed in oil wells, by an adjustment at the electric motor rotation based on signals provided by sensors installed on the surface and subsurface, keeping the pump operating within the recommended range, closest to the well s potential. Techniques are developed to estimate unmeasured variables, enabling the automation of wells that do not have all the required sensors. The automatic adjustment, according to an algorithm that runs on a programmable logic controller maintains the flow and submergence within acceptable parameters avoiding undesirable operating conditions, as the gas interference and high engine temperature, without need to resort to stopping the engine, which would reduce the its useful life. The control strategy described, based on modeling of physical phenomena and operational experience reported in literature, is materialized in terms of a fuzzy controller based on rules, and all generated information can be accompanied by a supervisory system

Smart material interfaces : a new form of physical interaction

Smart Material Interface (SMI) is the latest generation of user interface that makes use of engineered materials and leverages their special properties. SMIs are capable of changing their physical properties such as shape, size and color, and can be controlled under certain (external) conditions. We provide an example of such an SMI in the form of a prototype of a vacuum cleaner. The prototype uses schematic electrochromic polymer at the suction nozzle of the vacuum cleaner, which changes its color depending on the dust level on a floor. We emphasize on the new affordances and communication language supported by SMIs, which challenges the current metaphors of user interfaces in the field of HCI.

3D reconfigurable autopilot flight system for both general aviation and unmanned aerial systems

This research project investigated and designed a modular architecture for a 3D Reconfigurable Autopilot Flight System that could be used to control actuators in both manned and unmanned aircraft. The system is based on a CAN Bus interface and allows seamless control of different types of actuators. During the course of the research the differences and similarities of autopilots for fixed-wing general aviation aircraft and unmanned aircraft were analysed focusing on the actuator interfaces. This project suggests that software and hardware used in commercial-of-the-shelf avionics could be used in manned and unmanned aviation.

Uncanny nature: Hybrid stop motion using Blender

This talk gives an overview of the project "Uncanny Nature", which incoporates a style of animation called Hybrid Stop Motion, that combines physical object armatures with virtual copies. The development of the production pipeline (using a mix of Blender, Dragonframe, Photoscan and Arduino) is discussed, as well as the way that Blender was used throughout the production to visualise, model, animate and composite the elements together.