Fuel consumption of a tractor in function of wear, of ballasting and tire inflation pressure

When using appropriate inflation pressures and load capacity (ballast), it may obtain a higher yield and prolongation of the life of the tire, besides it may minimize the problems of loss of traction, increased slippage and fuel consumption. This study aimed to evaluate the fuel consumption of a tractor operating with new and worn tires in three conditions of ballasting and three inflation pressures, when driving on compacted soil with vegetation cover. The experiment was conducted at the experimental unit from the Department of Animal Science, Federal University of Lavras, state of Minas Gerais, Brazil, in an agricultural soil compacted by cattle trampling and with vegetation cover. It was used a tractor 4x2 with front wheel assist, of a 65.62 kW engine power. The tires were of R1 type, diagonal (front: 12.4 to 24; and rear: 18.4 to 30), the average height of the clutches of the new tires were 0.3 and 0.35 m for front and rear tires, respectively, and for the worn tires were 0.018 and 0.0045 m, for the front and the rear tires, respectively. The results showed advantages for the tractor equipped with new tires.

Spatial variability of noise level in agricultural machines

The knowledge of the spatial variability of noise levels and the build of kriging maps can help the evaluation of the salubrity of environments occupied by agricultural workers. Therefore, the objective of this research was to characterize the spatial variability of the noise level generated by four agricultural machines, using geostatistics, and to verify if the values are within the limits of human comfort. The evaluated machines were: harvester, chainsaw, brushcutter and tractor. The data were collected at the height of the operator's ear and at different distances. Through the results, it was possible to verify that the use of geostatistics, by kriging technique, made it possible to define areas with different levels for the data collected. With exception of the harvester, all of machines presented noise levels above than 85 dB (A) near to the operator, demanding the use of hearing protection.

Evaluation of the heating of broilers in shed by means of gas hoods and underfloor heating

This study was conducted to evaluate and compare the behavior of the heating inside poultry shed through gas hood and underfloor heating. The experiment was conducted in poultry shed belonging to the Federal Institute of Education, Science and Technology of Triângulo Mineiro Region, Uberlândia city – state of Minas Gerais (MG), Brazil. The dimensions of the shed are 24 meters long and 9.6 meters wide and with a ceiling height of 3.2 meters. The temperature was measured with an optical thermometer of Minipa brand, MT 350 model. It was used, to the analysis of temperature behavior, the public domain software FEMM 4.2, which uses finite elements techniques, with data collected from two lots. Underfloor heating is made using hot water flowing through a serpentine type system, which is installed below the bed; this hot water is from solar heaters. An energetic and economic assessment of the warming shed for raising chickens was realized. From the results obtained with the simulations, it may observe that the heating through the floor provides a more homogeneous distribution of temperature when compared with the hood heating. The flow of heat is upwards supplying, thus, the greatest need of heating of the bird, which is the pectoral part.

Corn productivity in function of surface application of lime in differents management systems and cultural preparation

The evaluation of technologies employed at the agricultural production system such as crop rotation and soil preparation, both associated with crop-livestock integration, is crucial. Therefore, the aim of the present study was to evaluate the incorporation of lime for three no-tillage systems and cultural managements in system of crop-livestock integration, with emphasis on corn grain yield. The experiment was conducted from January 2003 to April 2005 at Selvíria city, MS, in Dystroferric Red Latosol, clay texture. The experimental design was randomized blocks with split plots consisted of three main treatments, aimed the soil physics conditioning and the incorporation of lime: PD - No-no-tillage; CM - minimum no-tillage, and PC - conventional no-tillage; and of two secondary treatments related to the management: rotation and crop succession, with four replications. Data on agronomic traits of maize were analyzed: plant height, stem diameter, height of the first spike insertion, 100 grains weight and grain yield. The results showed that the maize produced under the system of crop-livestock integration is quite feasible, showing that grain yields are comparable to averages in the region and the different soil physical conditioning and incorporation of lime did not influence the corn yield as well as the cultural managements, rotation and succession, did not affect the maize crop behavior after two years of cultivation.

Esophagectomy with gastroplasty in advanced megaesophagus: late results of omeprazole use

Objective: To analyze the late results of advanced Chagasic megaesophagus treatment by esophagectomy associated with the use of proton pump inhibitor (omeprazole) as for the incidence of esophagitis and Barrett's esophagus in the remaining stump. Methods : We studied patients with advanced megaesophagus undergoing esophagectomy and transmediastinal esophagogastroplasty. Patients were divided into three groups: A (20) with esophageal replacement by full stomach, without the use of omeprazole; B (20) with esophageal replacement by full stomach, with omeprazole 40 mg/day introduced after the first postoperative endoscopy and maintained for six years; and C (30) with esophageal replacement by gastric tube with use of omeprazole. Dysphagia, weight loss and BMI were clinical parameters we analyzed. Upper gastrointestinal endoscopy was performed in all patients, and determined the height of the anastomosis, the aspect of the mucosa, with special attention to possible injuries arising from gastroesophageal reflux, and the patency of the esophagogastric anastomosis. Results : We studied 50 patients, 28 males (56%) and 22 (44%) females. All underwent endoscopy every year. In the first endoscopy, erosive esophagitis was present in nine patients (18%) and Barrett's esophagus, in four (8%); in the last endoscopy, erosive esophagitis was present in five patients (8%) and Barrett's esophagus in one (2%). When comparing groups B and C, there was no evidence that the manufacturing of a gastric tube reduced esophagitis and Barrett's esophagus. However, when comparing groups A and C, omeprazole use was correlated with reduction of reflux complications such as esophagitis and Barrett's esophagus (p <0.005). Conclusion : The use of omeprazole (40 mg/day) reduced the onset of erosive esophagitis and Barrett's esophagus during the late postoperative period.

Effects of zearalenone in prepubertal gilts

Prepubertal gilts were fed with a diet containing zearalenone (ZEA) in a concentration of 0.75 mg/kg for 21 days. The effects of this mycotoxin on morphologic aspects of the reproductive tract as well as on complete blood count (CBC), serum biochemistry analysis (SBA) and humoral immune response against sheep red blood cells (SRBC) were evaluated. There was a significant increase (P<0.05) on the reproductive tract weight, vulvar area, height of the epithelial cells of endometrial glands and uterine mucosa. These results showed the ability of this nonsteroidal mycotoxin in mimicking actions of 17β estradiol at the concentration of 0.75mg/kg. No changes in weight gain, CBC, SBA parameters and humoral response against SRBC were observed.

Thoracic and heart biometrics of non-anesthetized agouti (Dasyprocta primnolopha Wagler, 1831) measured on radiographic images

The agouti is a species intensively hunted throughout the Amazon and the semi-arid regions of northeastern Brazil. Considering the current trend in conservation management of wild species, the aim of this study was to determine the morphometric reference to the heart of agouti raised in captivity, based on thoracic and cardiac measurements in these animals. Thirty adult agoutis, 1 to 3 years of age, without clinical signs of cardiac disease were selected. The animals were physically restrained and radiographies in laterolateral (LL) and ventrodorsal (VD) recumbence were produced. The following measures were taken: the apicobasilar length of the heart (at the most cranial height of the Carina region to the heart apex) (AB), maximum width of the heart perpendicular to AB (CD), heart inclination angle (AIC), trachea inclination angle (AIT), distance from the right heart wall (DPTd), distance from the left heart wall (DPTe) and vertical depth of the thorax, and the ventral face of the vertebral column to the dorsal border of the sternum at the level of the trachea bifurcation (H). The ratios between AB/CD, AB/H and CD/H were also analyzed. To calculate the vertebral heart scale (VHS), the AB and CD measurements were laid over the thoracic vertebra starting at T4. Radiographic evaluation showed values consistent with those reported in small animals and some wild and exotic species. The main biometric values in the chest cavity and heart of agouti are arranged as follows: (1) The ratios between AB/H ratio and CD/H were not sensitive for identifying heart increases (p>0.05), while the ratio AB/CD was more sensitive in this identification (p<0.05); (2) AIC: 21.2±6.4º (mean between male and famale); (3) AIT for males and females: 9.93±3.23° and 8.4±3.94°; (4) DPTd and DPTe for males: 0.97±0.40cm and 0.7±0.30cm; (5) DPTd and DPTe for females: 1.12±0.42cm and 01.02±0.43cm; (6) VHS for males and females: 7.75±0.48v e 7.61±0.34v; (7) The caudal vena cava (CVC) was visualized dorsal-cranially and located right of the midline. The data obtained allowed the acquisition of the first reference values for biometry of the heart of agoutis, contributing to better understanding of cardiac morphology and identification of cardiomyopathy in these animals.

Morphological and morphometric evaluation of prepubertal gilt ovaries, uterine tubes and uterus at different oestrus cycle stages

Studies are performed in developing techniques/procedures that provide greater reproductive performance in farm animals, including pigs. In this sense, the study of gilts reproductive organs at different oestrus cycle stages for assessing the presence of abnormalities and/or other parameters that may affect the future animal fertility is important. In order to evaluate the morphological, morphometric and histomorphometric features of ovaries, uterus and uterine tubes (UTs) characteristics of prepubertal gilts at different oestrus cycle stages, reproductive tracts from 48 animals immediately after slaughter were obtained. After, the structures were dissected and removed, and the ovaries were used for classification of oestrus cycle stage of each gilt in follicular phase (FP) and luteal phase (FL). Then, morphometric evaluations of ovaries, UTs, uterine horns and uterine body were performed. Besides that, medial segments of UTs and uterus were fixed in Bouin solution, processed and included in paraffin, when histological sections of 5.0 micrometers (µm) were obtained and stained with Hematoxylin and Eosin. Histomorphometric analyzes using image capture system and specific software were performed. Afterwards, data were submitted to Student's t test for assessment the statistical differences (P<0.05) between the two different oestrus cycle stages (FP × LP) and between the placement of reproductive structures (right × left antimer). Among the gilts evaluated, 35 were in the FP and 13 in LP. There was no difference (P>0.05) between morphometric parameters of ovaries, UTs and uterus of gilts in FP and LP. Likewise, in respect to the placement of reproductive structures, both in the oestrus cycle stages, as in the general average, there was no difference (P>0.05). Regarding the histomorphometric variables, gilts classified in FP presented a higher (P<0.05) height of glandular and UT epithelium compared to animals in LP. On the other hand, the diameter of endometrial glands was higher (P<0.05) in gilts at LP compared to FP. Furthermore, gilts in LP presented a higher (P<0.05) proportion of endometrium occupied by glands, whereas animals in FP had a higher (P<0.05) proportion of connective tissue and blood vessels. In conclusion, in prepubertal gilts, the histomorphometric parameters as endometrial glands diameter, the height of glandular epithelium and of UT epithelium and the proportion of endometrium occupied by connective tissue, besides the glands and blood vessels varies through the oestrus cycle, possibly under the influence of ovarian steroids.

Interference of Sorghum sudanense and Eleucine indica in the soybean and corn cultivation

The natural infestations are composed of numerous species that compete for environmental resources such as water, light, nutrients and space. The objective of this study was to evaluate the interference of mixed infestations Sorghum sudanense (sudangrass) and Eleusine indica (goosegrass) in the presence of soybean and corn. The experimental design was completely randomized with four replications and the experimental units consisted of plastic pots with a volume capacity of 8 L. The treatments were associations of plants S. sudanense and E. indica in the proportions 8:0, 6:2, 4:4,2:6 and 0:8, respectively, corresponding to 100, 75, 50, 25 and 0% S. sudanense and the reverse for E. indica. In all treatments remained constant four soybean or corn plants per experimental unit. The variables analyzed in the weeds were shoot dry weight, root, total and height of plants. The competitive analysis was accomplished through diagrams applied to replacement series experiment and indexes of competiveness. The results indicated that E. indica was more competitive than S. sudanense in mixed infestations with corn. Rather, S. sudanense was more competitive than E. indica, in mixed infestations with soybean, demonstrating differences in competitiveness among the weeds.

APPLICATION HEIGHT IN HERBICIDES EFFICIENCY IN BEAN CROPS

ABSTRACTInadequate herbicide application can result in failures in weed control and/or poisoning of the crops, resulting in yield losses. In this research were assessed the effects of the sprayer nozzle boom height in the distribution of the spray solution for weed control, influencing intoxication of beans and crop yield. Experiments were conducted in laboratory and field conditions. In laboratory, the performance of flat spray tip TT 11002 was assessed at heights 0.20, 0.30, 0.40 and 0.50 meters with respect to the target surface. In the field the same heights were assessed in applications of herbicides fomesafen, fluazifop-P-butyl and fomesafen + fluazifop-P-butyl. There was an inverse relationship between the height of the spray boom and the coefficients of variation of the patterns. The mixture better efficiency in a tank of fluazifop-P-butyl + fomesafen was obtained with the height of 0.50 m from the target. This treatment resulted in better weed control, lower poisoning of the bean plants and better crop yield rates.

SELECTIVITY OF FOMESAFEN TO COTTON

ABSTRACT The aim of this work was to evaluate the selectivity of fomesafen alone or in a tank mixture with other preemergent herbicides, with or without S-metolachlor application in early postemergence in cotton plant, cultivar DP 555 BG RR(r). The design utilized was a randomized complete block, organized in a split-plot arrangement, with four replications. For that, 24 herbicides were evaluated with fomesafen (0.45 and 0.625 kg ha-1), prometryn (1.25 kg ha-1), diuron (1.25 kg ha-1), trifluralin (1.8 kg ha-1), and S-metolachlor (0.77 kg ha-1), applied as preemergent, with or without S-metolachlor (0.77 kg ha-1) applied in early postemergence. The variables evaluated were: phytotoxicity, insertion height of the first reproductive branch, plant height, stand, number of reproductive branches per plant, number of bolls per plant, bolls weight, and productivity of cotton seed. Fomesafen alone or in a tank mixture with preemergent prometryn, diuron, trifluralin and S-metolachlor was selective to cotton plant. Preemergent fomesafen isolated application followed by the application of S-metolachlor in early postemergence was also selective. However, on average, preemergent tank mixtures applied in association with preemergent S-metolachlor early application was not selective to cotton crop.

Structure and dynamics of a woody plant community of a tropical semi-deciduous seasonal forest in the "Estação Ecológica do Panga", municipality of Uberlândia, Minas Gerais, Brazil

Studies of plant community dynamics are essential in understanding the demographic patterns of species since changes in demographic rates can affect the floristic composition and future structure. The purpose of the present study was to analyze the changes in the community structure and floristic composition of woody plants in a tropical semi-deciduous forest in Uberlândia in central Brazil, during a 10-years period. The data were collected in 1989 and in 2000 in 50 quadrats (10 m x 10 m) where all trees with a minimum circumference at breast height of 10 cm were sampled. In 1989, 93 species and 1103 individuals were registered. Over a period of 10 years, seven new species were added to the community, although eight disappeared. The main change that occurred during this period in the floristic composition was the replacement of savannah species occurring in forest gaps by those from the forest understory.

A morphometric study of the lumbar spinous process in the Chinese population

Our goal was to analyze the anatomical parameters of the lumbar spine spinous process for an interspinous stabilization device designed for the Chinese population and to offer an anatomical basis for its clinical application. The posterior lumbar spines (T12-S1) of 52 adult cadavers were used for measuring the following: distance between two adjacent spinous processes (DB), distance across two adjacent spinous processes (DA), thickness of the central spinous processes (TC), thickness of the superior margin of the spinous processes (TS), thickness of the inferior margin of the spinous processes (TI), and height of the spinous processes (H). Variance and correlation analyses were conducted for these data, and the data met the normal distribution and homogeneity of variance. DB decreased gradually from L1-2 to L5-S1. DA increased from T12-L1 to L2-3 and then decreased from L2-3 to L4-5. The largest H in males was noted at L3 (25.45±5.96 mm), whereas for females the largest H was noted at L4 (18.71±4.50 mm). Usually, TS of the adjacent spinous process was lower than TI. Based on the anatomical parameters of the lumbar spinous processes obtained in this study, an “H”-shaped coronal plane (posterior view) was proposed as an interspinous stabilization device for the Chinese population. This study reports morphometric data of the lumbar spinous processes in the Chinese population, which provides an anatomical basis for future clinical applications.

Production of pizza dough with reduced fermentation time

The aim of this study was to reduce the fermentation time of pizza dough by evaluating the development of the dough during fermentation using a Chopin® rheofermentometer and verifying the influence of time and temperature using a 2² factorial design. The focus was to produce characteristic soft pizza dough with bubbles and crispy edges and soft in the center. These attributes were verified by the Quantitative Descriptive Analysis (QDA). The dough was prepared with the usual ingredients, fermented at a temperature range from 27 to 33 ºC for 30 to 42 minutes, enlarged, added with tomato sauce, baked, and frozen. The influence of the variables time and temperature on the release of carbon dioxide (H'm) was confirmed with positive and significant effect, using a rheofermentometer, which was not observed for the development or maximum height of the dough (Hm). The same fermentation conditions of the experimental design were used for the production of the pizza dough in the industrial process; it was submitted to Quantitative Descriptive Analysis (QDA), in which the samples were described by nine attributes. The results showed that some samples had the desired characteristics of pizza dough, demonstrated by the principal component analysis (PCA), indicating a 30 % fermentation time reduction when compared to the conventional process.

Coolability of porous core debris beds : Effects of bed geometry and multi-dimensional flooding

This thesis addresses the coolability of porous debris beds in the context of severe accident management of nuclear power reactors. In a hypothetical severe accident at a Nordic-type boiling water reactor, the lower drywell of the containment is flooded, for the purpose of cooling the core melt discharged from the reactor pressure vessel in a water pool. The melt is fragmented and solidified in the pool, ultimately forming a porous debris bed that generates decay heat. The properties of the bed determine the limiting value for the heat flux that can be removed from the debris to the surrounding water without the risk of re-melting. The coolability of porous debris beds has been investigated experimentally by measuring the dryout power in electrically heated test beds that have different geometries. The geometries represent the debris bed shapes that may form in an accident scenario. The focus is especially on heap-like, realistic geometries which facilitate the multi-dimensional infiltration (flooding) of coolant into the bed. Spherical and irregular particles have been used to simulate the debris. The experiments have been modeled using 2D and 3D simulation codes applicable to fluid flow and heat transfer in porous media. Based on the experimental and simulation results, an interpretation of the dryout behavior in complex debris bed geometries is presented, and the validity of the codes and models for dryout predictions is evaluated. According to the experimental and simulation results, the coolability of the debris bed depends on both the flooding mode and the height of the bed. In the experiments, it was found that multi-dimensional flooding increases the dryout heat flux and coolability in a heap-shaped debris bed by 47–58% compared to the dryout heat flux of a classical, top-flooded bed of the same height. However, heap-like beds are higher than flat, top-flooded beds, which results in the formation of larger steam flux at the top of the bed. This counteracts the effect of the multi-dimensional flooding. Based on the measured dryout heat fluxes, the maximum height of a heap-like bed can only be about 1.5 times the height of a top-flooded, cylindrical bed in order to preserve the direct benefit from the multi-dimensional flooding. In addition, studies were conducted to evaluate the hydrodynamically representative effective particle diameter, which is applied in simulation models to describe debris beds that consist of irregular particles with considerable size variation. The results suggest that the effective diameter is small, closest to the mean diameter based on the number or length of particles.