The N-terminal region containing the zinc finger domain of tobacco streak virus coat protein is essential for the formation of virus-like particles

Tobacco streak virus (TSV), a member of the genus Ilarvirus (family Bromoviridae), has a tripartite genome and forms quasi-isometric virions. All three viral capsids, encapsidating RNA 1, RNA 2 or RNA 3 and subgenomic RNA 4, are constituted of a single species of coat protein (CP). Formation of virus-like particles (VLPs) could be observed when the TSV CP gene was cloned and the recombinant CP (rCP) was expressed in E. coli. TSV VLPs were found to be stabilized by Zn2+ ions and could be disassembled in the presence of 500 mM CaCl2. Mutational analysis corroborated previous studies that showed that an N-terminal arginine-rich motif was crucial for RNA binding; however, the results presented here demonstrate that the presence of RNA is not a prerequisite for assembly of TSV VLPs. Instead, the N-terminal region containing the zinc finger domain preceding the arginine-rich motif is essential for assembly of these VLPs.

Thermoelectric Properties of Two-Phase PbTe with Indium Inclusions

The thermoelectric figure of merit (zT) can be increased by introduction of additional interfaces in the bulk to reduce the thermal conductivity. In this work, PbTe with a dispersed indium (In) phase was synthesized by a matrix encapsulation technique for different In concentrations. x-Ray diffraction analysis showed single-phase PbTe with In secondary phase. Rietveld analysis did not show In substitution at either the Pb or Te site, and this was further confirmed by room-temperature Raman data. Low-magnification (similar to 1500x) scanning electron microscopy images showed micrometer-sized In dispersed throughout the PbTe matrix, while at high magnification (150,000x) an agglomeration of PbTe particles in the hot-pressed samples could be seen. The electrical resistivity (rho) and Seebeck coefficient (S) were measured from 300 K to 723 K. Negative Seebeck values showed all the samples to be n-type. A systematic increase in resistivity and higher Seebeck coefficient values with increasing In content indicated the role of PbTe-In interfaces in the scattering of electrons. This was further confirmed by the thermal conductivity (kappa), measured from 423 K to 723 K, where a greater reduction in the electronic as compared with the lattice contribution was found for In-added samples. It was found that, despite the high lattice mismatch at the PbTe-In interface, phonons were not scattered as effectively as electrons. The highest zT obtained was 0.78 at 723 K for the sample with the lowest In content.

Phenyl carbohydrazone conjugated 2-oxoindoline as a new scaffold that augments the DNA and BSA binding affinity and anti-proliferative activity of a 1,10-phenanthroline based copper(II) complex

A new type of copper(II) complex, CuL(phen)(2)](NO3) (CuIP), where L ((E)-N'-(2-oxoindolin-3-ylidene) benzohydrazide) is a N donor ligand and phen is the N, N-donor heterocyclic 1,10-phenanthroline, has been synthesized. The phenyl carbohydrazone conjugated isatin-based ligand L and CuIP were characterized by elemental analysis, infrared, UV-Vis, H-1 and C-13 NMR and ESI-mass spectral data, as well as single-crystal X-ray diffraction. The interaction of calf thymus DNA (CT DNA) with L and CuIP has been investigated by absorption, fluorescence and viscosity titration methods. The complex CuIP displays better binding affinity than the ligand L. The observed DNA binding constant (K-b = 4.15(+/- 0.18) x 10(5) M-1) and binding site size (s = 0.19), viscosity data together with molecular docking studies of CuIP suggest groove binding and/or a partial intercalative mode of binding to CT DNA. In addition, CuIP shows good binding propensity to the bovine serum albumin (BSA) protein, giving a K-BSA value of 1.25(+/- 0.24) x 10(6) M-1. In addition, the docking studies on DNA and human serum albumin (HSA) CuIP interactions are consistent with the consequence of binding experiments. The in vitro anti-proliferative study establishes the anticancer potency of the CuIP against the human cervical (HeLa) and breast (MCF7) cancer cells; noncancer breast epithelial (MCF10a) cells have also been investigated. CuIP shows better cytotoxicity and sensitivity towards cancer cells over noncancer ones than L under identical conditions, with the appearance of apoptotic bodies. (C) 2014 Elsevier B.V. All rights reserved.

Nanomaterial based Magnetic Resonance Imaging of Cancer

Magnetic Resonance Imaging (MRI) is a widely used non-invasive medical tool for detection and diagnosis of cancer. In recent years, MRI has witnessed significant contributions from nanotechnology to incorporate advanced features such as multimodality of nanoparticles, therapeutic delivery, specific targeting and the optical detectability for molecular imaging. Accurate composition, right scheme of surface chemistry and properly designed structure is essential for achieving desired properties of nanomaterials such as non-fouling surface, high imaging contrast, chemical stability, target specificity and/or multimodality. This review provides an overview of the recent progress in theranostic nanomaterials in imaging and the development of nanomaterial based magnetic resonance imaging of cancer. In particular, targeted theranostics is a promising approach along with its targeting strategy in cancer treatment using MRI and multimodal imaging. We also discuss recent advances in integrin mediated targeted MRI of cancer.

PECVD grown SiC cantilevers with Dry and Wet Release

Cantilevers made out of PECVD grown SiC films are reported here. The cantilevers were realized in two different methods isotropic etch (Dry release) and combination of wet etch and critical point dry release. The dry release process for Silicon isotropic etch results in excellent etch selectivity against SiC, to provide released structures. The optimized wet release process is able to overcome stiction issues to provide excellent SiC cantilevers.

On the strain rate sensitivity of plastic flow in metallic glasses

The nanoindentation technique was employed to examine the strain rate sensitivity, m, and its dependence on the structural state of a Zr-based bulk metallic glass (BMG). The free volume content in the BMG was varied by examining samples in the as-cast (AC), shot-peened (SP), and structurally relaxed (SR) states. Hardness values measured at different loading rates and over a temperature range of 300-423 K as well as the strain-rate jump tests conducted in the quasi-static regime at room temperature, show that m is always negative. All the load-displacement (P-h) curves in this temperature regime exhibit serrated load-displacement responses, indicating that the shear band mediated inhomogeneous plastic flow governs deformation. Such localization of flow and associated softening is the raison d'etre for the negative m. Significant levels of pile-up around the indents were also noted. The order in the average values of hardness, pile-up heights, and the displacement bursts on the P-h curves was always such that SR > AC > SP, which is also the order of increasing free volume content. These observations were utilized to discuss the reasons for the negative strain rate sensitivity, and its dependence on the structural state of metallic glasses. It is suggested that the positive values of m reported in the literature for them are possibly experimental artefacts that arise due to large pile ups around the indents which lead to erroneous estimation in hardness values. (C) 2014 Elsevier B.V. All rights reserved.

FEM Simulations and Optimization about Residual Stresses in Coating Structures with Functionally Graded Materials Layer

An elasto-plastic finite element method is developed to predict the residual stresses of thermal spraying coatings with functionally graded material layer. In numerical simulations, temperature sensitivity of various material constants is included and mix

Properties of tetrahedral amorphous carbon deposited by a filtered cathodic vacuum arc

The properties of a highly sp3 bonded form of amorphous carbon denoted ta-C deposited from a filtered cathodic vacuum arc (FCVA) are described as a function of ion energy and deposition temperature. The sp3 fraction depends strongly on ion energy and reaches 85% at an ion energy of 100 eV. Other properties such as density and band gap vary in a similar fashion, with the optical gap reaching a maximum of 2.3 eV. These films are very smooth with area roughness of order 1 nm. The sp3 fraction falls suddenly to almost zero for deposition above about 200 °C.

Comparative study of the slurry erosion and free-fall particle erosion of aluminum

A study has been performed of the erosion of aluminium by silica sand particles at a velocity of 4.5 m s-1, both air-borne and in the form of a water-borne slurry. Measurements made under similar experimental conditions show that slurry erosion proceeds at a rate several times that of air-borne erosion, the ratio of the two rates depending strongly on the angle of impact. Sand particles become embedded into the metal surface during air-borne particle erosion, forming a composite layer of metal and silica, and provide the major cause of the difference in wear rate. The embedded particles giving rise to surface hardening and a significant reduction in the erosion rate. Embedment of erodent particles was not observed during slurry erosion. Lubrication of the impacting interfaces by water appears to have minimal effect on the wear of aluminium by slurry erosion.

Evaluación del suministro de agua de la red hidráulica del parque de ciencias Estelí Mar - Estelí, 2008

El estudio surge como respuesta a la escasa información sobre abastecimientos de agua cuando se utilizan pozos y equipos de bombeo, además tiene la finalidad de generar los elementos necesarios al parque de ciencias Estelimar e interesa dos en este tipo de investigación para que pueda aprovecharse sosteniblemente el recurso agua, usar eficientemente el equipo de bombeo al mismo tiempo reducir los costos de energía que se generan con el abastecimiento de agua en estas condiciones. Los objetivos de la investigación fueron: caracterizar el acuífero existente, describir las red hidráulica, conocer el punto de operación de la bomba así mismo de terminar los costos de energía generados en el abastecimiento de los deposito demandantes. Para caracterizar el acuífero existente se realizó una prueba de bombeo a caudal constante en el pozo Estelimar que comprendió 7 horas de extracción y 8 de recuperación también se analizó el perfil estratigráfico de un pozo situado a 100m del sitio en estudio. La red hidráulica se describió con el apoyo de un mapa elaborado por técnicos de Estelimar acompañados de observaciones directas en las instalaciones de la red. En el caso del punto de operación de la bomba fue necesario aforar todas las salidas hacia los de pósitos demandantes, mediciones de voltaje e intensidad de corriente y un levantamiento topográfico por taquimetría. Los costo de energía fueron determinados utilizando además de las descarga de agua obtenidas del aforo las capacidades de cada depósito. Finalmente se concluye que el acuífero afectado por el pozo estelimar presenta características de semiconfinado estimándose su transmisividad en 423.36 m2/día, el nivel estático registrado fue de 26.60m produciéndose un rebajamiento de 27.30m, se identificaron tres codos de 90º, seis tee, tres válvulas de compuertas y un codo de 45º, la tubería de succión es de hierro y el de descarga PVC, ambos de 2 pulg de diámetro, el punto en que opera la bomba con un 63% de eficiencia es de 1.03l/s venciendo una carga de trabajo de 45.50m, los costos de energía registrados para los meses de abril,mayo, junio y julio del 2008 están alrededor de C$8233.54 (Còrdobas).

Work Softening And Annealing Hardening Of Deformed Nanocrystalline Nickel

We reported that work softening takes place during room-temperature rolling of nanocrystalline Ni at an equivalent strain of around 0.30. The work softening corresponds to a strain-induced phase transformation from a face-centered cubic (fcc) to a body-centered cubic (bcc) lattice. The hardness decreases with increasing volume fraction of the bcc phase. When the deformed samples are annealed at 423 K, a hardening of the samples takes place. This hardening by annealing can be attributed to a variety of factors including the recovery transformation from the bcc to the fcc phase, grain boundary relaxation, and retardation of dislocation gliding by microtwins.

Critical serrated flow features during nanoindentation in La-based bulk metallic glasses

La57.6Al17.5(Cu,Ni)(24.9) and La64Al14(Cu,Ni)(22) bulk metallic glasses (BMGs) were prepared by copper-mould casting method. Plastic deformation behavior of the two BMGs at various loading rates was studied by nanoindentation. The results showed that the La57.6Al17.5(Cu,Ni)(24.9) BMG with a glass transition temperature of 423 K exhibited prominent serrated flow at low loading rates, whereas less pronounced serrated flow at high rates during nanoindentation. In contrast, the La64Al14(Cu,Ni)(22) BMG with a glass transition temperature of 401 K exhibited prominent serrated flow at high loading rates. The different rate dependency of serrated flow in the two La-based BMGs is related to the different glass transition temperature, and consequently the degree of viscous flow during indentation at room temperature. A smoother flow occurs in the alloy with relatively lower glass transition temperature, due to the relaxation of stress concentration.

Diversidad de aves en ocho comunidades del territorio Miskitu Indian Tasbaisca Kum, Reserva de Biósfera Bosawás, Nicaragua

La introducción de ganado en las áreas tradicionalmente agrícolas en el territorio Miskitu Indian Tasbaiska Kum ha influido en una modificación en su orden territorial para dar cabida a éste nuevo rubro por parte de sus habitantes. Es comúnmente conocido que la ganadería es una de las actividades productivas más incompatiblescon el bosque y la conservación de los elementos dentro de éste último, pero la rotación de las áreas de cultivo y pastoreo, y el uso de sistemas silvopastoriles podría reducir el impacto hacia los ambientes naturales. Con este estudio se plantea determinar la diversidad biológica de avifauna en los sistemas silvopastoriles ubicados en las cercanías de ocho comunidades del territorio Miskitu Indian Tasbaiska Kum, con el fin de determinar su potencial para preservar aves, en especial, aves de importancia para la conservación nacional. Para lograr los objetivos se realizó conteos de aves mediante el uso de puntos de conteo por comunidad, en las áreas donde suele llevarse a pastorear al ganado. En el estudio se invirtieron tres días por comunidad y se realizaron al menos dos observaciones por día, una entre las 06:00-10:00 y otra entre las 16:00 – 18:00. Con los datos obtenidos se calculó diferentes parámetros de diversidad biológica. Como resultado se observó un total de 423 individuos los cuales están agrupados en 67 especies y 27 familias. Las especies de aves más abundantes fueron: Brotogeris jugularis,Ramphocelus passerinii y Amazona auropaliata. Las comunidades Amarrana,Shiminka y Yakalpanani son las que registraron los mayores valores de los parámetros de biodiversidad. Se determinaron 14 especies en algún grado de conservación según la lista de los apéndices de CITES para Nicaragua y las listas del Sistema Nacional de Vedas 2012, entre éstas se incluyen Brotogeris jugularis y Amazona aurapaliata,as cuales resultaron también abundantes. La comunidad que concentró la mayor cantidad de aves en algún estado de con servación fue Yakalpanani. Las especies de plantas asociadas con la mayor diversidad de aves fueron especies de estadíos tempranos de sucesión como:Cecropia peltata ,Inga sp, Guazuma ulmifolia y Muntingia calabura. Aunque Yakalpanani es una de las comunidades más grandes, comparado con Boca de Plis, la ubicación de su área de pastoreo entre masas boscosas conservadas ha garantizado que los parámetros de diversidad biológica hayan resultado significativamente mayores en ésta, dado a una conectividad hasta el momento poco irrumpida.