Micelle size characterization of lipopeptides produced by B. subtilis and their recovery by the two-step ultrafiltration process

The aim of this work was to investigate the lipopeptides aggregation behavior in single and mixed solutions in a wide range of concentrations, in order to optimize their separation and purification following the two-step ultrafiltration process and using large pore size membranes (up to MWCO = 300 kDa). Micelle size was determined by dynamic light scattering. In single solutions of lipopeptide both surfactin and mycosubtilin formed micelles of different size depending on their concentration, micelles of average diameter = 5–105 nm for surfactin and 8–18 nm for mycosubtilin. However when the lipopeptides were in the same solution they formed mixed micelles of different size (d = 8 nm) and probably conformation to that formed by the individual lipopeptide, this prevents their separation according to size. These lipopeptides were purified from fermentation culture by the two-step ultrafiltration process using different MWCO membranes ranging from 10 to 300 kDa. This led to their effective rejection in the first ultrafiltration step by membranes with MCWO = 10–100 kDa but poor rejection by the 300 KDa membrane. The lipopeptides were recovered at 90% purity (in relation to protein) and with 2.34 enrichment in the permeate of the second ultrafiltration step with the 100 KDa membrane upon addition of 75% ethanol.

Single-step chemical synthesis of ferrite hollow nanospheres

We report a single-step chemical synthesis of iron oxide hollow nanospheres with 9.3 nm in diameter. The sample presents a narrow particle diameter distribution and chemical homogeneity. The hollow nature of the particles is confirmed by HRTEM and HAADF STEM analysis. Electron and x-ray diffraction show that the outer material component is constituted by 2 nm ferrite crystals. Mossbauer data provide further evidence for the formation of iron oxide with high structural disorder, magnetically ordered at 4.2 K and superparamagnetism at room temperature. An unusual magnetic behavior under an applied field is reported, which can be explained by the large fraction of atoms existing at both inner and outer surfaces.

Bond Strength of Two-Step Etch-and-Rinse Adhesive Systems to the Dentin of Primary and Permanent Teeth

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Effect of chlorhexidine on bond strength of two-step etch-and-rinse adhesive systems to dentin of primary and permanent teeth

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Nd:YAG Laser Irradiation of Etched/Unetched Dentin Through an Uncured Two-step Etch-and-Rinse Adhesive and its Effect on Microtensile Bond Strength

Purpose: To evaluate whether Nd:YAG laser irradiation of etched and unetched dentin through an uncured adhesive affected the microtensile bond strength (pTBS).Materials and Methods: Flat dentin surfaces were created in 19 extracted human third molars. Adper Single Bond (SB) adhesive was applied over etched (groups 1 to 3) or unetched dentin (groups 4 to 6). The dentin was then irradiated with a Nd:YAG laser through the uncured adhesive, using 0.75 or 1 W power settings, except for the control groups (groups 1 and 4). The adhesive was light cured and composite crowns were built up. After 24 h, the teeth were sectioned into beams, with cross-sectional areas of 0.49 mm(2), and were stressed under tension. Data were statistically analyzed using two-way ANOVA and Tukey's test (alpha = 5%). Dentin surfaces of fractured specimens and the interfaces of untested beams were observed under scanning electron microscopy (SEM).Results: Acid etching, laser irradiation, and their interaction significantly affected bonding (p < 0.05). Laser irradiation did not improve bonding of etched dentin to resin (p > 0.05). However, higher pTBS means were found on unetched lased dentin (groups 5 and 6), but only in comparison to group 4, where neither lasing nor etching was performed. Groups 4 to 6 showed the lowest pTBS means among all groups tested (p < 0.05). Laser irradiation did not change the characteristics of the hybrid layers created, while solidification globules were observed on lased dentin surfaces under SEM.Conclusion: Laser irradiation of dentin through the uncured adhesive did not significantly improve the pTBS in comparison to the suggested manufacturer's technique.

Evaluation of a two-step pouring technique for implant-supported prostheses impression

The aim of this study was to evaluate the efficacy of a pouring technique for implant-supported prostheses impressions. A metallic matrix (control group) with two implants positioned at 90 and 65 degrees was fabricated. The matrix was submitted to the direct transfer impression technique. In group CP (conventional pouring - n = 10), casts were obtained by the conventional pouring technique. In group EP (experimental pouring - n = 10), the analogs were embraced with latex tubes before the first pouring and then submitted to a second pouring. Vertical misfit and implants/analogs inclinations were evaluated. Data were analyzed by analysis of variance and Tukey's test (p < .05). Results demonstrated significant difference (p < .05) between control and experimental groups for misfit measurement in perpendicular implant/analog and between control group and group EP in leaning implant/analog. Considering inclination, there were significant differences (p < .05) between control and experimental groups for leaning analogs. Independently of the pouring technique, perpendicular implants produced more accurate casts.

Higgs decay rate to two photons in a model with two fermiophobic-Higgs doublets

We consider a three Higgs doublet model with an S3 symmetry in which beside the standard model-like doublet, there are two fermiophobic doublets. Due to the new charged scalars, there is an enhancement in the two-photon decay, while the other channels have the same decay widths as the standard model neutral Higgs. The fermiophobic scalars are mass degenerated unless soft terms breaking the S3 symmetry are added. © 2013 American Physical Society.

Effects of diuron on toxicological and hematological parameters and lymphohematopoietic organs in a rat chemical hepatocarcinogenesis model

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Exact field-driven interface dynamics in the two-dimensional stochastic Ising model with helicoidal boundary conditions

We investigate the interface dynamics of the two-dimensional stochastic Ising model in an external field under helicoidal boundary conditions. At sufficiently low temperatures and fields, the dynamics of the interface is described by an exactly solvable high-spin asymmetric quantum Hamiltonian that is the infinitesimal generator of the zero range process. Generally, the critical dynamics of the interface fluctuations is in the Kardar-Parisi-Zhang universality class of critical behavior. We remark that a whole family of RSOS interface models similar to the Ising interface model investigated here can be described by exactly solvable restricted high-spin quantum XXZ-type Hamiltonians. (C) 2012 Elsevier B.V. All rights reserved.