Alkali activated materials based on fluid catalytic cracking catalyst residue (FCC): Influence of SiO2/Na2O and H 2O/FCC ratio on mechanical strength and microstructure

Reuse of industrial and agricultural wastes as supplementary cementitious materials (SCMs) in concrete and mortar productions contribute to sustainable development. In this context, fluid catalytic cracking catalyst residue (spent FCC), a byproduct from the petroleum industry and petrol refineries, have been studied as SCM in blended Portland cement in the last years. Nevertheless, another environmental friendly alternative has been conducted in order to produce alternative binders with low CO2 emissions. The use of aluminosilicate materials in the production of alkali-activated materials (AAMs) is an ongoing research topic which can present low CO2 emissions associated. Hence, this paper studies some variables that can influence the production of AAM based on spent FCC. Specifically, the influence of SiO 2/Na2O molar ratio and the H2O/spent FCC mass ratio on the mechanical strength and microstructure are assessed. Some instrumental techniques, such as SEM, XRD, pH and electrical conductivity measurements, and MIP are performed in order to assess the microstructure of formed alkali-activated binder. Alkali activated mortars with compressive strength up to 80 MPa can be formed after curing for 3 days at 65°C. The research demonstrates the potential of spent FCC to produce alkali-activated cements and the importance of SiO2/Na2O molar ratio and the H2O/spent FCC mass ratio in optimising properties and microstructure. © 2013 Elsevier Ltd. All rights reserved.

Soil and crop residue CO2-C emission under tillage systems in sugarcane-producing areas of southern Brazil

Appropriate management of agricultural crop residues could result in increases on soil organic carbon (SOC) and help to mitigate gas effect. To distinguish the contributions of SOC and sugarcane (Saccharum spp.) residues to the short-term CO2-C loss, we studied the infl uence of several tillage systems: heavy offset disk harrow (HO), chisel plow (CP), rotary tiller (RT), and sugarcane mill tiller (SM) in 2008, and CP, RT, SM, moldboard (MP), and subsoiler (SUB) in 2009, with and without sugarcane residues relative to no-till (NT) in the sugarcane producing region of Brazil. Soil CO2-C emissions were measured daily for two weeks after tillage using portable soil respiration systems. Daily CO2-C emissions declined after tillage regardless of tillage system. In 2008, total CO2-C from SOC and/or residue decomposition was greater for RT and lowest for CP. In 2009, emission was greatest for MP and CP with residues, and smallest for NT. SOC and residue contributed 47% and 41%, respectively, to total CO2-C emissions. Regarding the estimated emissions from sugarcane residue and SOC decomposition within the measurement period, CO2-C factor was similar to sugarcane residue and soil organic carbon decomposition, depending on the tillage system applied. Our approach may define new emission factors that are associated to tillage operations on bare or sugarcane-residue-covered soils to estimate the total carbon loss.

Nutrient intake and digestibility of the lipid residue of biodiesel from palm oil in sheep

ABSTRACT: The objective of this study was to evaluate the effect of inclusion of lipid residue of biodiesel originated in the processing of palm oil (Elaeis guineensis) in the diet on the digestibility of feedlot lambs. Twenty-five crossbred male castrated lambs, weighing 20±1.61 kg, were distributed in randomized blocks with five treatments and five replications. The experimental period lasted 22 days; 15 for diet adaptation, 2 for the adaptation to the indicator LIPE (lignin from Eucalyptus grandis isolated, purified and enriched, UFMG, Minas Gerais) and 5 for fecal sampling. Diets were formulated with 64% concentrate based on corn and soybean meal, 31% Massai grass (Panicum maximum cv. Massai) hay and 5% lipid supplementation from increasing levels of substitution of 0, 25, 50, 75 and 100% of palm oil for biodiesel oil from palm residue. The lambs were offered two meals a day, at 7h00 and 16h00. There was linear effect of inclusion of the residue from palm oil biodiesel on dry matter intake. There was no change in digestibility of nutrients except for ether extract. The use of biodiesel from palm oil residue up to 100% replacement for the lipid supplementation of sheep positively influences the consumption without altering the digestibility of nutrients.

Kinetic role of a histidine residue in the T1 copper site of the laccase from Rigidoporus lignosus

Laccases (benzendiol:oxygen oxidoreductases; EC 1.10.3.2) catalyze the oxidation of a broad range of substrates, such as polyphenols, dyes and pollutants, and thus these enzymes are widely applied in industrial, biotechnological and environmental fields. In order to improve their biotechnological applications, a deep knowledge of structural factors involved in controlling their activity, in various experimental conditions and on different substrates, is required. In the present study, a laccase from the mushroom Rigidoporus lignosus was kinetically characterized. In particular, the stability, the effects of pH, ionic strength and fluoride ion concentration on the kinetic parameters were investigated, using three di-hydroxy-benzene isomers (1,2-dihydroxy-benzene, 1,3-dihydroxy-benzene and 1,4-dihydroxy-benzene) as substrates. The catalytic constant values of the laccase showed a bell-shaped pH profile, with the same optimum pH and pK(a) values for all tested substrates. This behavior appears to be due to the presence of an ionizable residue in the enzyme active site. To identify this residue, the enzyme was derivatized with diethylpyrocarbonate to modify accessible histidine residues, which, according to structural data, are present in the active site of this enzyme. The kinetic behavior of the derivatized laccase was compared with that of the native enzyme and the derivatized residues were identified by mass spectrometry. Mass spectrometry and kinetic results suggest the main role of His-457 in the control of the catalytic activity of laccase from R. lignosus. (C) 2013 Elsevier B.V. All rights reserved.

Thermal Characteristics of Lignin Residue from Industrial Processes

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Association between pharyngeal residue and posterior oral spillage with penetration and aspiration in Stroke

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

ORGANIC RESIDUE AND PHOSPHORUS AS CONDITIONERS OF DEGRADED SOIL AND EFFECTS ON THE INITIAL GROWTH OF Dipteryx alata Vog.

In northwestern Sao Paulo State, it was established, in 1965, the hydroelectric station of Ilha Solteira (CESP) that produced extensive degraded areas, from where it was removed the soil superficial layers. For the re-establishment of the vegetation, in areas like these, it is necessary the addition of chemical inputs and organic material. Associating the presence in the area of macrophytes, to the need of recovery of degraded areas and the availability of seeds from native species of Cerrado, it was intended the development of this work, with the objective of evaluating the addition effects of organic residue and phosphorus on the material of degraded soil and on the initial growth of Dipteryx alata, arboreal species of 'cerrado'. The soil material was collected in area of degraded soil by the construction of Ilha Solteira hydroelectric station. The experiment was conducted in two environmental conditions, greenhouse and plenty of sun. The treatments consisted of four phosphorus doses (0, 100, 200 and 300 mg dm(-3) of P2O5), with or without macrophytes addition, with 16 treatments and 10 repetitions each one. The used macrophytes, collected at Jupia hydroelectric station, in Mato Grosso do Sul state, were dried, sliced, incorporated to the soil material and incubated during 60 days. The seeds of Dipteryx alata, collected around of the area, were sowed in washed sand and after 60 days introduced in the treatments. The plants were appraised monthly for height, stem diameter and leaves chlorophyll. After 210 days, the plants were collected and evaluated for fresh and dry weight of aerial part and radicular system and the soil material was evaluated for fertility and microbial activity by the carbon of liberated CO2. The organic residue, incorporated to the material of soil degraded, positively affects the soil fertility and the soil microbial activity. The applied phosphorus doses influenced the behavior of Ca, SB, H+Al and CTC, when applied in the absence of organic residue, it promoted significant and linear increments for values of potential acidity, and indicated the organic residue importance. The initial growth of the Dipteryx alata was favored by the protected cultivation, for the incorporation of organic residue and for the phosphorus addition to the soil. At the end although the material of degraded soil comes as good perspective for disposal of this residue, studies about the field conditions are necessary.

Effectiveness of the compound chlorpyrifos plus cypermethrin plus citronellal against Alphitobius diaperinus. Laboratory analysis and residue determination in carcasses

Biological security and the absence of residues in meat Effectiveness, and/or eggs must be considered when recommending options for the control Alphitobius diaperinus in poultry production environments. This research study evaluated the effectiveness of cypermethrin+chlorpyrifos+citronellal in the control of A. diaperinus, including analysis for the presence of residues of this compound in poultry carcasses (experimental farm). Two studies were carried out under laboratory conditions. One used paper filters a four dilutions of the compound, and the other used a container including with pulverized broiler litter and the compound. The analysis of carcasses for residues was conducted in broilers that raised in a broiler house treated (floor and/or litter) with the compound at a dilution of 1:800. Birds were regularly sacrificed, submitted to necropsy, and liver, muscle and fat fragments were collected. Gas chromatography was used to identify the possible presence of any chemical residue in these samples. High effectiveness rates against A.diaperinus were observed in the two laboratory studies, as well as the absence of residues in the carcasses. This compound, can be recommended as a valuable used in the studied concentrations, alternative for the control and treatment of A. diaperinus.

Determination of the p-monochlorophenol residue in the calcium hydroxide plus p-monochlorophenol combination used as an intracanal dressing in pulpless teeth of dogs with induced chronic periapical lesion

To determine the presence of p-monochlorophenol in the calcium hydroxide (Calen) + p-monochlorophenol combination after its use as intracanal dressing, periapical lesions were induced in 60 root canals of upper and lower premolars of four dogs, After biomechanical preparation, the root canals received the intracanal medication, which was removed from the apical third after 2, 4, 7, and 14 days for chemical analysis by spectrophotometry, the results showed a p-monochlorophenol loss of approximately 50.0% in the dressing after 48 h, with no further significant loss after longer periods of times, p-Monochlorophenol was still present in the medication after 14 days.

Optimization of in situ derivatization SPME by experimental design for GC-MS multi-residue analysis of pharmaceutical drugs in wastewater

This paper presents the development of a procedure, which enables the analysis of nine pharmaceutical drugs in wastewater using gas chromatography-mass spectrometry (GC-MS) associated with solid-phase microextraction (SPME) for the sample preparation. Experimental design was applied to optimize the in situ derivatization and the SPME extraction conditions. Ethyl chloroformate (ECF) was employed as derivatizing agent and polydimethylsiloxane-divinylbenzene (PDMS-DVB) as the SPME fiber coating. A fractional factorial design was used to evaluate the main factors for the in situ derivatization and SPME extraction. Thereafter, a Doehlert matrix design was applied to find out the best experimental conditions. The method presented a linear range from 0.5 to 10 mu g/L, and the intraday and interday precision were lower than 16%. Applicability of the method was verified from real influent and effluent samples of a wastewater treatment plant, as well as from samples of an industry wastewater and a river.

Effect of the inclusion of fish residue oils in diets on the fatty acid profile of muscles of males and females lambari (Astyanax altiparanae)

This study evaluated the effects of two lipids sources of fish residue (tilapia and salmon) compared with a vegetable oil source (soybean oil) on the fatty acid profiles of male and female lambari. This experiment was developed in a completely randomized experimental design in a 3 x 2 factorial arrangement, totaling 6 treatments resulting from the combination of the three experimental diets for both sexes, with four replications for each treatment. This study involved 120 male (2.58 +/- 0.13 g) and 72 female lambari (4.00 +/- 0.09 g), fed the experimental diets twice a day until apparent satiation for a period of 60 days. Oleic, linoleic, palmitic and stearic fatty acids were found at higher concentrations in all experimental oils and diets, as well in the muscle of male and female lambari. The low amounts of arachidonic, eicosapentaenoic and docosahexaenoic acids in the experimental diets and subsequent greater concentrations in muscle tissue, suggested that lambari are able to desaturate and elongate the chain of fatty acids with 18 carbons. The fish of both sexes that received the diet with soybean oil showed high levels of n-6 fatty acids, especially of C18: 2n-6 and low levels of eicosapentaenoic and docosahexaenoic acids. The diet with salmon residue oil promoted higher levels of fatty acids of the n-3 series and resulted in the best n-3/n-6 ratio in the muscle of male and female lambari. The oils from fish residues can be a substitute for traditional fish oil and its use in the lambari diets does not impair its growth.

Dasatinib Overrides Imatinib Resistance Mediated by the F359I Residue Mutation in Two Patients with Chronic Myeloid Leukemia

Despite the beneficial effects of imatinib mesylate, some patients may either not respond or respond suboptimally. Here, we report two chronic myelogenous leukemia patients; one had a suboptimal response according to European LeukemiaNet criteria (a major molecular response was not achieved after 18 months of standard-dose imatinib therapy) and the other had failure with a standard dose of imatinib. At the time of the suboptimal response in patient 1 and the failure in patient 2, we were able to detect the F359I mutation in the BCR-ABL tyrosine kinase domain using DNA sequencing in both patients. Therefore, it was decided to change the therapeutic regimen to dasatinib at a dose of 100 mg once daily in both patients. This change resulted in the achievement of complete cytogenetic remission in patient 1 after 4 months and a major molecular response within 2 and 3 months in both patients. Detection of the F359I mutation in our two cases likely explains the suboptimal response to imatinib in case 1 and the failure in case 2. This implies that in such cases dasatinib should be considered to effectively suppress the mutated clones. Copyright (C) 2011 S. Karger AG, Basel

Development of methodology for determination of pesticides residue in water by SPE/HPLC/DAD

To boost crop yield, sugarcane growers are using increasing amounts of pesticides to combat insects and weeds. But residues of these compounds can pollute water resources, such as lakes, rivers and aquifers. The present paper reports the results of a study of water samples from the Feijao River, which is the source of drinking water for the city of Sao Carlos, Sao Paulo, Brazil. The samples were evaluated for the presence of four leading pesticides - ametryn, atrazine, diuron and fipronil - used on sugarcane, the dominant culture in the region. The samples were obtained from three points along the river: the headwaters, along the middle course of the river and just before the municipal water intake station. The pesticides were extracted from the water samples by solid-phase extraction (SPE) and then analyzed by liquid chromatography with diode array detection (LC-DAD). The analytical method was validated by traditional methods, obtaining recovery values between 90 and 95%, with precision deviations inferior to 2.56%, correlation coefficients above 0.99 and detection and quantification limits varying from 0.02 to 0.05 mg L-1 and 0.07 to 0.17 mg L-1, respectively. No presence of residues of the pesticides was detected in the samples, considering the detection limits of the method employed.

Valutazione dell'effetto del mezzo temprante sulle tensioni residue e proprieta meccaniche della lega di alluminio Al-Si7-Mg

L’alluminio, grazie alla sua bassa temperatura di fusione e all’elevata fluidità di molte leghe, è uno dei metalli più versatili in fonderia. Per ottenere il massimo delle proprietà resistenziali, le leghe che lo permettono sono sottoposte a trattamento termico. Questo, però, in componenti geometricamente complessi può far insorgere tensioni residue che inficeranno la resistenza del materiale durante la sua messa in esercizio. Gli obiettivi della presente ricerca sono stati: la valutazione dell’incidenza del mezzo temprante usato durante il trattamento termico sulle tensioni residue che si sviluppano nella lega AlSi7Mg e la definizione di come questo potesse essere modificato per ridurre le tensioni senza peggiorare le proprietà resistenziali del materiale. Per tale ragione sono state eseguite prove di trattamento termico, analisi microstrutturali e test di durezza su campioni estratti direttamente da getti colati in sabbia.

Determinazione delle tensioni residue in componenti metallici sottili mediante "incremental hole drilling"

La vita di un aeromobile è un elemento importante sia per quanto riguarda la sicurezza del payload, che da un punto di vista economico, a causa delle spese di manutenzione/rinnovamento della flotta che una compagnia aerea deve affrontare. Gli elementi costitutivi di un aeromobile sono soggetti a diverse tipologie di carichi, alcuni dei quali ciclici come la pressurizzazione/depressurizzazione della fusoliera; tali carichi, nel lungo periodo, possono provocare la nascita e la propagazione di eventuali cricche, le quali possono portare alla rottura del componente stesso causando gravi incidenti. Il legame tra tensioni residue e nascita/crescita delle cricche ha portato allo sviluppo di tecniche per contrastare questo fenomeno, come il processo del LSP. Per la misura delle tensioni residue esistono già normative di riferimento, le quali però non trattano componenti metallici di piccolo spessore mentre i pannelli di fusoliera rientrano in questa categoria. Scopo di questa tesi è quello di studiare una variante della tecnica HD adatta a valutare le tensioni residue in componenti metallici di piccolo spessore e confrontare i risultati con quelli ottenuti con la tecnica XRD. L’idea di partenza è l’implementazione di un supporto posteriore in resina che simuli la presenza di uno spessore maggiore.