Design of Mm-Wave RLSA with lossy waveguides by slot coupling control techniques

This paper discusses how to design a Radial Line Slot Antenna (RLSA) whose waveguide is filled with high loss dielectric materials. We introduce a new design for the aperture slot coupling synthesis to restrain the dielectric losses and improve the antenna gain. Based on a newly defined slot coupling, a number of RLSAs with different sizes and loss factors are analyzed and their performances are predicted. Theoretical calculations suggest that the gain is sensitive to the material losses in the radial lines. The gain enhancement by using the new coupling formula is notable for larger antenna size and higher loss factor of the dielectric material. Three prototype RLSAs are designed and fabricated at 60GHz following different slot coupling syntheses, and their measured performances consolidate our theory.

Subwavelength Index Engineering for SOI Waveguides

Photonic structures with a sub-wavelength pitch, small enough to suppress diffraction, can behave as equivalent homogenous materials that can be engineered to exhibit a specific refractive index and dispersion. Here we discuss the design of a variety of integrated photonic devices, ranging from grating couplers to multimode interference couplers, for which the use of sub-wavelength structures enables unique characteristics. We will place special emphasis on the design and experimental demonstration of multi-mode interference couplers with an unprecedented bandwidth beyond 200nm at telecom wavelengths.

Optical Waveguides and Structures for Short Haul Optical Communication Channels within Printed Circuit Boards

Optical waveguides have shown promising results for use within printed circuit boards. These optical waveguides have higher bandwidth than traditional copper transmission systems and are immune to electromagnetic interference. Design parameters for these optical waveguides are needed to ensure an optimal link budget. Modeling and simulation methods are used to determine the optimal design parameters needed in designing the waveguides. As a result, optical structures necessary for incorporating optical waveguides into printed circuit boards are designed and optimized. Embedded siloxane polymer waveguides are investigated for their use in optical printed circuit boards. This material was chosen because it has low absorption, high temperature stability, and can be deposited using common processing techniques. Two sizes of waveguides are investigated, 50 $unit{mu m}$ multimode and 4 - 9 $unit{mu m}$ single mode waveguides. A beam propagation method is developed for simulating the multimode and single mode waveguide parameters. The attenuation of simulated multimode waveguides are able to match the attenuation of fabricated waveguides with a root mean square error of 0.192 dB. Using the same process as the multimode waveguides, parameters needed to ensure a low link loss are found for single mode waveguides including maximum size, minimum cladding thickness, minimum waveguide separation, and minimum bend radius. To couple light out-of-plane to a transmitter or receiver, a structure such as a vertical interconnect assembly (VIA) is required. For multimode waveguides the optimal placement of a total internal reflection mirror can be found without prior knowledge of the waveguide length. The optimal placement is found to be either 60 µm or 150 µm away from the end of the waveguide depending on which metric a designer wants to optimize the average output power, the output power variance, or the maximum possible power loss. For single mode waveguides a volume grating coupler is designed to couple light from a silicon waveguide to a polymer single mode waveguide. A focusing grating coupler is compared to a perpendicular grating coupler that is focused by a micro-molded lens. The focusing grating coupler had an optical loss of over -14 dB, while the grating coupler with a lens had an optical loss of -6.26 dB.

Direct Write Fabrication of Waveguides and Interconnects for Optical Printed Wiring Boards

Current copper based circuit technology is becoming a limiting factor in high speed data transfer applications as processors are improving at a faster rate than are developments to increase on board data transfer. One solution is to utilize optical waveguide technology to overcome these bandwidth and loss restrictions. The use of this technology virtually eliminates the heat and cross-talk loss seen in copper circuitry, while also operating at a higher bandwidth. Transitioning current fabrication techniques from small scale laboratory environments to large scale manufacturing presents significant challenges. Optical-to-electrical connections and out-of-plane coupling are significant hurdles in the advancement of optical interconnects. The main goals of this research are the development of direct write material deposition and patterning tools for the fabrication of waveguide systems on large substrates, and the development of out-of-plane coupler components compatible with standard fiber optic cabling. Combining these elements with standard printed circuit boards allows for the fabrication of fully functional optical-electrical-printed-wiring-boards (OEPWBs). A direct dispense tool was designed, assembled, and characterized for the repeatable dispensing of blanket waveguide layers over a range of thicknesses (25-225 µm), eliminating waste material and affording the ability to utilize large substrates. This tool was used to directly dispense multimode waveguide cores which required no UV definition or development. These cores had circular cross sections and were comparable in optical performance to lithographically fabricated square waveguides. Laser direct writing is a non-contact process that allows for the dynamic UV patterning of waveguide material on large substrates, eliminating the need for high resolution masks. A laser direct write tool was designed, assembled, and characterized for direct write patterning waveguides that were comparable in quality to those produced using standard lithographic practices (0.047 dB/cm loss for laser written waveguides compared to 0.043 dB/cm for lithographic waveguides). Straight waveguides, and waveguide turns were patterned at multimode and single mode sizes, and the process was characterized and documented. Support structures such as angled reflectors and vertical posts were produced, showing the versatility of the laser direct write tool. Commercially available components were implanted into the optical layer for out-of-plane routing of the optical signals. These devices featured spherical lenses on the input and output sides of a total internal reflection (TIR) mirror, as well as alignment pins compatible with standard MT design. Fully functional OEPWBs were fabricated featuring input and output out-of-plane optical signal routing with total optical losses not exceeding 10 dB. These prototypes survived thermal cycling (-40°C to 85°C) and humidity exposure (95±4% humidity), showing minimal degradation in optical performance. Operational failure occurred after environmental aging life testing at 110°C for 216 hours.

Tunable single- and dual-wavelength SHG from diode-pumped PPKTP waveguides

A compact, all-room-temperature, widely tunable, continuous wave laser source in the green spectral region (502.1–544.2 nm) with a maximum output power of 14.7 mW is demonstrated. This was made possible by utilizing second-harmonic generation (SHG) in a periodically poled potassium titanyl phosphate (PPKTP) crystal waveguide pumped by a quantum-well external-cavity fiber-coupled diode laser and exploiting the multimode-matching approach in nonlinear crystal waveguides. The dual-wavelength SHG in the wavelength region between 505.4 and 537.7 nm (with a wavelength difference ranging from 1.8 to 32.3 nm) and sum-frequency generation in a PPKTP waveguide is also demonstrated.

Cephalometric And Anthropometric Data Of Obstructive Apnea In Different Age Groups.

Patients with obstructive sleep apnea syndrome usually present with changes in upper airway morphology and/or body fat distribution, which may occur throughout life and increase the severity of obstructive sleep apnea syndrome with age. To correlate cephalometric and anthropometric measures with obstructive sleep apnea syndrome severity in different age groups. A retrospective study of cephalometric and anthropometric measures of 102 patients with obstructive sleep apnea syndrome was analyzed. Patients were divided into three age groups (≥20 and <40 years, ≥40 and <60 years, and ≥60 years). Pearson's correlation was performed for these measures with the apnea-hypopnea index in the full sample, and subsequently by age group. The cephalometric measures MP-H (distance between the mandibular plane and the hyoid bone) and PNS-P (distance between the posterior nasal spine and the tip of the soft palate) and the neck and waist circumferences showed a statistically significant correlation with apnea-hypopnea index in both the full sample and in the ≥40 and <60 years age group. These variables did not show any significant correlation with the other two age groups (<40 and ≥60 years). Cephalometric measurements MP-H and PNS-P and cervical and waist circumferences correlated with obstructive sleep apnea syndrome severity in patients in the ≥40 and <60 age group.

CARACTERÍSTICAS DE QUALIDADE DO CONTRAFILÉ (m. L. dorsi) DE TOUROS JOVENS DA RAÇA NELORE

Quality traits of boneless rib cut (L. dorsi muscle) from Nelore young bulls. To study the meat quality traits of Nelore breed young bulls, and the effect of age (690-780 days) on them, 113 animals were slaughtered after 109 days of intensive feeding with 20% concentrate and 80% roughage. All the carcasses were graded at the slaughter floor by the Federal Inspection and chilled for 24 hours (Tinitial=5°C, Tfinal=2°C). Fifty one half carcasses (right side), type B - B R A S I L `s grading system - from animals of 23 to 26 months were boned and separated into commercial cuts. Two steaks (2.5cm thick) were removed from each boneless rib cut (m. L. dorsi), vacuum packaged and aged for 7 days (0-2°C). The pH varied from 5.44 to 5.83 and only two samples had pH ³ 5.70. The L* (brightness) average value was 34.85. The water and fat content were 75.65% and 1.71%, respectively. The average WB shear force was 6.70kg, and it was not affected by age (690-734 days), but presented a trend (t test, p=0.22) for increasing values between 735 and 780 days. Animal age did not affect other quality traits (t test, p>0.20). It was concluded that the rib cut from Nelore young bulls may not have a good acceptability in exigent markets, and that carcasses graded B, presumed to be the best grade, do not necessarily present the best meat quality characteristics.

Analise de volumes parciais do tronco durante a respiração por videogrametria

Universidade Estadual de Campinas . Faculdade de Educação Física

Proposição, validação e aplicação de um novo metodo para analise cinematica tridimensional da movimentação da caixa toracica durante a respiração

Universidade Estadual de Campinas . Faculdade de Educação Física

Metodologia para analise da movimentação da caixa toracica durante a respiração

Universidade Estadual de Campinas . Faculdade de Educação Física

Características de carcaça de suínos de três linhagens genéticas em diferentes idades ao abate

O objetivo deste trabalho foi estudar as características da carcaça de suínos de diferentes linhagens genéticas, em diferentes idades ao abate. Foram utilizados 88 suínos por linhagem, fêmeas e machos castrados, com idade e peso médio iniciais de 74 dias e 30kg, respectivamente, pertencentes a três linhagens genéticas distintas, designadas de AgroceresPic, Dalland e Seghers. A etapa experimental foi dividida em quatro fases (Crescimento I, Crescimento II, Terminação I e Terminação II). Ao final de cada etapa, foram abatidos 60 animais (10 por linhagem/sexo), para as caracterizações: Peso (PCQ) e Rendimento de Carcaça Quente (RCQ), Área de Olho de Lombo (AOL) e Espessura de Toucinho (ET). Na análise dos resultados foi utilizado um delineamento inteiramente casualizado com desdobramento dos graus de liberdade em esquema fatorial 4 x 3 x 2, sendo quatro idades ao abate (90, 119, 150 e 186 dias), três linhagens (AgroceresPic, Dalland e Seghers) e dois sexos (fêmea e macho castrado), com 10 repetições por tratamento, sendo utilizado o pacote PROC MIXED do Softwear SAS. Os valores médios de peso vivo apresentaram diferença entre as linhagens e interação entre fase e linhagem (P<0,05). Os valores médios das demais variáveis estudadas apresentaram diferença e a interação (P<0,05) entre fase, linhagem e sexo, sendo que de maneira geral as principais diferenças ocorreram a partir da fase de Terminação I, em que as fêmeas das linhagens AgroceresPic e Dalland apresentaram melhores resultados (P<0,05) de RCQ (80,4 e 80,7%, respectivamente) em comparação com os machos (78,8 e 78,7%, respectivamente) e além disso as fêmeas Dalland apresentaram valores superiores (P<0,01) de AOL e ET (45,7cm² e 11,4mm x 38,3cm² e 18,3mm). Conclui-se que as linhagens genéticas avaliadas apresentaram características de carcaça muito interessantes para o mercado atual e que as fêmeas suínas podem ser utilizadas em programas que visem o abate de animais mais pesados.

Carcass quality of feedlot finished steers fed yeast, monensin, and the association of both additives

To evaluate the effects of the supplementation of feed additives on carcass quality in beef cattle, 72 Nellore steers (339.5kg, 20-month old) were feedlot finished and fed for 91 days one of the following diets: 1) control with no additives; or added of 2) live yeast culture; 3) monensin; or 4) the association of both additives. After slaughter, renal, pelvic, and inguinal fat and hot carcass weights were recorded and carcass was split into muscle, bone, and trimmable fat. Carcass Longissimus muscle area and subcutaneous fat thickness at the 12th rib were measured and steaks of Longisimus muscle were taken to determine meat color, shear force, drip, and cooking losses. Yeast increased carcass dressing percentage but there were no effects on hot carcass weight, Longissimus area, subcutaneous fat thickness, percentage and weight of retail cut yield and trimmings. Feed additives had no effect on carcass pH, meat color, fat content, shear force, and drip losses. Supplementation of yeast, monensin or the association of both additives had no important effects on carcass traits and on meat quality of feedlot finished steers.

Crescimento alométrico dos componentes da carcaça de cordeiros Texel × Ile de France confinados do desmame aos 35kg de peso vivo

Foi avaliado o crescimento alométrico de ossos, músculos e gordura, e das regiões da carcaça de cordeiros Texel × Ile de France, terminados em confinamento. Vinte cordeiros, machos não-castrados, foram desmamados aos 42 dias de idade (15,9 ± 2,1kg de peso vivo) e confinados em baias individuais recebendo alimentação ad libitum. Destes, cinco foram abatidos 10 dias após o desmame e, os remanescentes, aos 25, 30 ou 35kg de peso vivo. Para determinação do crescimento alométrico dos cortes e tecidos foi utilizada a equação exponencial Y = aXb, transformada logaritmicamente em um modelo linear. Observou-se crescimento precoce (b = 0,89) da paleta, ao passo que a perna, a costela e o pescoço apresentaram crescimento isogônico (b = 1,00, 1,03 e 1,11, respectivamente), ou seja, equivalente ao da carcaça. O aumento do peso da carcaça implicou em redução da taxa de crescimento de ossos e músculos (b = 0,60 e 0,92, respectivamente) e aumento da taxa de crescimento da gordura (b = 1,78). O crescimento muscular foi diferenciado nas distintas regiões da carcaça, sendo isogônico na paleta (b = 0,98) e na perna (b = 0,99) e precoce na costela (b = 0,90) e no pescoço (b = 0,79). Recomenda-se que o abate de cordeiros Texel × Ile de France seja realizado com, no máximo, 30kg de peso vivo.

Características de carcaça de ovelhas de descarte das raças Ideal e Texel terminadas em dois sistemas de alimentação

Avaliaram-se as características de carcaça de ovelhas de descarte das raças Ideal e Texel terminadas em dois sistemas de alimentação. Utilizaram-se 20 ovelhas (10 da raça Ideal e 10 da raça Texel) aleatoriamente distribuídas de acordo com o grupo genético em dois manejos alimentares (confinamento e pastagem cultivada). Os abates foram realizados quando os animais atingiram 3,5 pontos de condição corporal. Os pesos de carcaça quente (PCQ) e de carcaça fria (PCF) e os rendimentos de carcaça quente (RCQ) e de carcaça fria (RCF) das ovelhas Texel foram maiores que os das ovelhas Ideal: 27,85 e 19,04 kg; 27,08 e 18,43 kg; 47,25 e 45,20% e 45,95 e 43,72%, respectivamente. O peso dos cortes perna, paleta, pescoço e costela e os pesos de músculos, ossos e gordura da perna dos animais da raça Texel foram superiores aos obtidos na raça Ideal. Quando avaliadas em porcentagem do peso corporal, no entanto, essas características não diferiram entre as duas raças. O manejo alimentar não influenciou as características de carcaça de ovelhas de descarte. Ovelhas Texel apresentam cortes maiores que os de ovelhas Ideal.

Active waveguide effects from porous anodic alumina: An optical sensor proposition

We present in this paper an active waveguide effect observed in porous anodic alumina (PA), which can be applied in optical sensors. The spectral position, shape, and polarization effect of the narrow waveguide modes is described. An analytical test with a commercial pesticide was performed. (C) 2010 American Institute of Physics. [doi: 10.1063/1.3447375]