Sediment description, CaCO3, density and porosity at DSDP Site 89-585

Siliceous sediments and sedimentary rocks occur as chert and silicified chalk, limestone, and claystone in Site 585 lower Miocene to Campanian sediments, with one older occurrence of chert near the Cenomanian/Turonian boundary. The recovered drill breccia in the Miocene to middle Eocene interval is dominated by bright red, orange, yellow, and brown chips and fragments of chert. In early Eocene and older sediments gray silicified limestone and yellowish brown chert fragments predominate. Recovery is poor in cores with chert because chert tends to fracture into smaller pieces that escape the drill and because the hard chert fragments grind away other sediments during rotary drilling. Thin-section and hand-sample studies show complex diagenetic histories of silicification (silica pore infill) and chertification (silica replacement of host rock). Multiple events of silicification can occur in the same rocks, producing chert from silicified limestone. Despite some prior silicification, silicified limestone is porous enough to provide conduits for dissolved silica-charged pore waters. Silicification and chert are more abundant in the coarser parts of the sedimentary section. These factors reflect the importance of porosity and permeability as well as chemical and lithologic controls in the process of silica diagenesis.

Porosity, permeability, trace elements, and carbon-oxygen isotopes at DSDP Hole 77-536

Talus deposits recovered from Site 536 show evidence of aragonite dissolution, secondary porosity development, and calcite cementation. Although freshwater diagenesis could account for the petrographic features of the altered talus deposits, it does not uniquely account for isotopic or trace-element characteristics. Also, the hydrologic setting required for freshwater alteration is not easily demonstrated for the Campeche Bank. A mixing-zone model does not account for the available trace-element data, but does require somewhat less drastic assumptions about the size of the freshwater lens. Although a seawater (bottom-water) alteration model requires no hydrologic difficulties, unusual circumstances are required to account for the geochemical characteristics of the talus deposits using this model.

Porosity, gas permeability and grain density of ODP Leg 194 sites

We report analyses of porosity and permeability of core samples from Site 1193 in the Northern Marion Platform, Sites 1196 and 1199 in the Southern Marion Platform, and Sites 1194, 1195, 1197, and 1198 from the slopes of these platforms. The samples include 415 horizontal 1-in plugs, 290 vertical 1-in plugs, and 23 whole-core pieces. Porosity and permeability analyses were possible for most, but not all, samples. Grain density measurements were also obtained for the horizontal plugs. Representative photomicrographs are provided of thin sections from 139 of the horizontal plugs and the 23 whole-core pieces.

Effective stress, porosity, p-wave velocity and mineral composition of ODP Hole 174A-1073A sediments

Porosity, permeability, and compressional (P-wave) velocity were measured as a function of stress on sediments from Ocean Drilling Program Site 1073, U.S. Mid-Atlantic continental slope. Thin sections, scanning electron microscopy, and X-ray diffraction analyses provided mineralogical characteristics of the samples. Uniaxial strain boundary conditions were imposed on the samples during consolidation tests with the maximum effective axial stress reaching 13 MPa. The maximum effective radial stress necessary to maintain uniaxial strain was 7.6 MPa. Over an effective axial stress interval of 0 to 5.2 MPa, Sample 174A-1073A-26X-2, 82-89 cm (226.65 meters below seafloor [mbsf]), exhibited the largest decrease in porosity (51% to 41%), whereas Sample 71X-1, 2-8 cm (644.70 mbsf), exhibited the smallest decrease in porosity (48% to 45%). All samples showed negligible porosity increases during unloading. The permeability (on the order of 1 x 10-17 m**2) of Sample 174A-1073A-71X-1, 2-8 cm, was twice that measured on Sample 8H-1, 23-26 cm (63.75 mbsf), even though the former was considerably deeper and older. The differences in porosity-stress behavior and permeability between shallow and deep samples is related to lithologic, mineralogic, and diagenetic differences between the sediments above and below the Pliocene-Pleistocene to Miocene unconformity. P-wave velocity for Samples 174A-1073A-41X-5, 97-103 cm (372.35 mbsf), and 71X-1, 2-8 cm, increased with decreasing porosity, but did not change significantly during unloading.