Production of whey protein-based aggregates under ohmic heating

Formation of whey protein isolate protein aggregates under the influence of moderate electric fields upon ohmic heating (OH) has been monitored through evaluation of molecular protein unfolding, loss of its solubility, and aggregation. To shed more light on the microstructure of the protein aggregates produced by OH, samples were assayed by transmission electron microscopy (TEM). Results show that during early steps of an OH thermal treatment, aggregation of whey proteins can be reduced with a concomitant reduction of the heating chargeby reducing the come-up time (CUT) needed to reach a target temperatureand increase of the electric field applied (from 6 to 12 V cm1). Exposure of reactive free thiol groups involved in molecular unfolding of -lactoglobulin (-lg) can be reduced from 10 to 20 %, when a CUT of 10 s is combined with an electric field of 12 V cm1. Kinetic and multivariate analysis evidenced that the presence of an electric field during heating contributes to a change in the amplitude of aggregation, as well as in the shape of the produced aggregates. TEM discloses the appearance of small fibrillar aggregates upon the influence of OH, which have recognized potential in the functionalization of food protein networks. This study demonstrated that OH technology can be used to tailor denaturation and aggregation behavior of whey proteins due to the presence of a constant electric field together with the ability to provide a very fast heating, thus overcoming heat transfer limitations that naturally occur during conventional thermal treatments.

Mejoramiento del comportamiento térmico de sistemas de calentamiento de agua solares termosifónicos hechos con materiales no convencionales y con tanques de almacenamiento verticales y horizontales Performance improvement of solar thermosyphonic systems for water heating made of non conventional materials and using horizontal and vertical storage tanks

El objeto de estudio de este proyecto son los sistemas de calentamiento de agua mediante energía solar que funcionan termosifónicamente. En particular se tratará con dos diseños particulares generados por fabricantes de la Provincia de Córdoba y que han solicitado el asesoramiento del Grupo de Energía Solar (GES) para el mejoramiento de la performance térmica de dichos equipos. Se trata de dos sistemas que tienen materiales no tradicionales y se diferencian además por tener una distinta disposición del tanque de almacenamiento: uno es en forma vertical y el otro en forma horizontal. Basados en los resultados de un ensayo bajo norma internacional, donde se detectaron algunas puntos factibles de mejora, se propone en este proyecto el análisis en detalle de los equipos, para lo cual se les debe desarmar completos, para realizar un estudio analítico y experimental de los mismos con el objeto de hacer un planteo teórico-analítico del comportamiento de los mismos, con la implementación de propuestas de mejora y chequeo de los resultados. Se propone entonces como objetivo lograr un mejoramiento de la performance térmica de los citados equipos a partir de un estudio experimental y analítico. Asumiendo esta posibilidad de mejora, se plantea la hipótesis de que es posible representar el funcionamiento de estos equipos mediante modelos físico-matemáticos desarrollados a partir de ecuaciones y correlaciones conocidas y procesos a interpretar mediante resoluciones numéricas y softwares específicos de simulación. De esta manera, se plantea el despieze completo de los equipos para estudiar en detalle su estructura y conexiones internas y a partir de la geometría, dimensiones y propiedades termofísicas de materiales constructivos y fluidos de trabajo, realizar modelos físico-matemáticos que permitan realizar variaciones de propiedades y geometría y así buscar las mejores combinaciones que produzcan equipos más eficientes térmicamente. Los modelos físico-matemáticos serán codificados en lenguajes de alto nivel para poder luego de una validación de los modelos, correr simulaciones en un software de reconocimiento internacional que permite sumar dichos modelos mediante un protocolo de comunicación, haciendo que las poderosas prestaciones del software se puedan aplicar a nuestros modelos. Se complementará el estudio con un análisis exergético para identificar los puntos críticos en que se producen las pérdidas de oportunidad de aprovechar la energía disponible, para así analizar cómo solucionar los problemas en dichos puntos. Los materiales a utilizar serán los propios equipos provistos por los fabricantes, que serán modificados convenientemente para operarlos como prototipos Se espera obtener un conocimiento acabado de los procesos y principios de funcionamiento de los equipos, que permita plantear las mejoras, las cuales se implementarán en los prototipos, realizándose una medición mediante norma igual a la inicial para ver en que magnitud se logran las mejoras esperadas. Se pretende además que las mejoras a implementar, en la etapa de transferencia a las empresas involucradas, redunden no sólo en un beneficio técnico, sino que también los sea desde el punto de vista económico. Para ello se trabajará también sobre los procesos y métodos de fabricación para que los equipos mejorados no sean mas caros que los originales y de ser posible sean aún más económicos, todo esto apuntando a la difusión de la energía solar térmica y poner al alcance de todos estos equipos tan convenientes para la propagación de las energías limpias. El proyecto redundará también en un importante beneficio para el conocimiento de la comunidad científica en general, con el aporte de nuevos resultados en diseños novedosos y con nuevos materiales. Además, la institución se beneficiará con la formación que obtendrán los integrantes del proyecto, muchos de ellos en etapa de realización de sus estudios de posgrado y en una etapa importante de su vida como investigadores. The main goal of this project is the improvement of two thermosyphonic solar water heating systems, made of non conventional materials and with different arrangement of their storage tanks: one is vertical and the other one horizontal. The thermosyphonic systems are provided by manufacturers of the Córdoba Province, who came to the Solar Energy Group (GES) of the National University of Río Cuarto looking for help for the design of their products. In an agreement with these manufacturers, it was proposed this project in order to work analytically and experimentally in order to obtain physical-mathematical models of these two systems, which allow for changes to look by means of simulations the best changes to implement on the equipments for the improvement of their thermal performance. Then, the materials to be used are the proper systems provided by the manufacturers, which will be disarmed to be studied in detail. After the analytical study the proposals of improvement will be implemented in a high level language of programming to perform simulations in the environment of a well-known software for energy simulations (TRNSYS). After the simulations, the best modifications will be physically implemented in the prototypes to perform finally the same normalized test of the beginning and check the magnitude of the implemented improvements. The importance of this project is based on the offer of better systems the companies would make, which would benefit the deployment of the thermal solar energy. Another relevant point is to make the new equipments at the same cost of the previous ones or cheaper, in order to achieve a good deployment of the solar water heating systems; then, the manufacture processes and methods must be studied to obtain not only good technical solutions, but also economical equipments. In addition, this project will contribute to the increasing of the knowledge in the area of thermosyphonic solar systems and the training of postgraduate students.

The appraisal of anaerobic digestion in Ireland to develop improved designs and operational practice

Mesophilic Anaerobic Digestion treating sewage sludge was investigated at five full-scale sewage treatment plants in Ireland. The anaerobic digestion plants are compared and evaluated in terms of design, equipment, operation, monitoring and management. All digesters are cylindrical, gas mixed and heated Continuously Stirred Tank Reactors (CSTR), varying in size from 130m3 to 800m3. Heat exchanger systems heat all digesters. Three plants reported difficulties with the heating systems ranging from blockages to insufficient insulation and design. Exchangers were modified and replaced within one year of operation at two plants. All but one plant had Combined Heat and Power (CHP) systems installed. Parameter monitoring is a problem at all plants mainly due to a lack of staff and knowledge. The plant operators consider pH and temperature the most important parameters to be measured in terms of successful monitoring of an anaerobic digester. The short time taken and the ease at which pH and temperature can be measured may favour these parameters. Three laboratory scale pilot anaerobic digesters were operated using a variety of feeds over at 144-day period. Two of the pilots were unmixed and the third was mechanically mixed. As expected the unmixed reactors removed more COD by retention of solids in the digesters but also produced greater quantities of biogas than the mixed digester, especially when low solids feed such as whey was used. The mixed digester broke down more solids due to the superior contact between the substrate and the biomass. All three reactors showed good performance results for whey and sewage solids. Scum formation occurred giving operational problems for mixed and unmixed reactors when cattle slurry was used as the main feed source. The pilot test was also used to investigate which parameters were the best indicators of process instability. These trials clearly indicated that total Volatile Fatty Acid (VFA) concentrations was the best parameter to show signs of early process imbalance, while methane composition in the biogas was good to indicate possible nutrient deficiencies in the feed and oxygen shocks. pH was found to be a good process parameter only if the wastewater being treated produced low bicarbonate alkalinities during treatment.

Modellierung und Simulation polydisperser Wassernebel in der Brandbekämpfung unter Berücksichtigung stochastischer Parameter

Magdeburg, Univ., Fak. für Verfahrens- und Systemtechnik, Diss., 2011

Entwicklung einer Impulsmethode zur Ermittlung thermodynamischer und reaktionskinetischer Parameter in der heterogenen Katalyse

Heterogeneous catalysis, homogeneous catalysis, adsorption equilibrium, reaction kinetics, impulse method, hydrolysis of methyl formate, production of formic acid

mögliche Rolle CGRP-immunreaktiver thalamo-amygdalärer Projektionen bei der durch Emotionen hervorgerufenen Veränderung vegetativer Parameter

CGRP amygdala thalamus fear blood pressure heart rate body temperature telemetry tracing projections

Klinische Parameter und Laborprofile bei der Abklärung des Verdachts auf eine Heparin-induzierte Thrombozytopenie (HIT) Typ II bei Patienten nach herzchirurgischen Eingriffen

Magdeburg, Univ., Med. Fak., Diss., 2012

Anwendung des EM-Algorithmus zur Schätzung der Parameter von Fluoreszenzlebensdauerfunktionen

Die Bachelorarbeit behandelt die Schätzung der Parameter von Fluoreszenzlebensdauerfunktionen mit Hilfe des EM-Algorithmus. Dabei wird der Algorithmus sowohl auf simulierte als auch auf gemessene Daten angewandt. Die Schätzung der Parameter erfolgt zunächst global für die gesamte Probe mit Hilfe eines Simplex-Verfahrens, um dann das Verhältnis der Komponenten der Fluoreszenzlebensdauer, also die Wahrscheinlichkeit, mit der ein Photon von einer Komponente stammt, für jedes Pixel eines Bildes durch den EM-Algorithmus zu bestimmen. Die Messungen liegen als Anzahl der gemessenen Photonen in diskreten Zeitintervallen vor, dabei fehlt jedoch die Information, wie viele der Photonen in einem der Intervalle zu einer Komponente gehören. Durch die Nutzung bedingter Erwartungswerte ist der EM-Algorithmus in der Lage, ohne Verzerrung mit diesen unbekannten Daten umzugehen. Weiterhin wird die Schätzung dadurch erschwert, dass die Daten durch Faltung der Fluoreszenzlebensdauerfunktion mit einer so genannten Apparatefunktion zustandekommen und das Modell somit sehr komplex wird. Auch für dieses Problem wird im Laufe der Arbeit eine Lösung vorgestellt.

Optimal experimental design for parameter identification and model selection

Magdeburg, Univ., Fak. für Elektrotechnik und Informationstechnik, Diss., 2014

Untersuchungen zur Perzeption musikalischer Parameter von Cochlea-Implantat-Trägern mit den Sprachkodierungsstrategien ACE und MP3000 im Vergleich zu normalhörenden Probanden

Magdeburg, Univ., Med. Fak., Diss., 2014

Aging and growth parameter from the Piaractus mesopotamicus (pacu) from the Cuiabá river, Mato Grosso, Brazil

This study has aims to determine the age and to estimate the growth parameters using scales of the species. Individuals of Piaractus mesopotamicus (Holmberg, 1887) used in this study were captured in the commercial fishery conducted in the region, along the year 2006. The model selected to express the growth of the species was the von Bertalanffy Sl= Sl∞*[1-exp-k(t-to)]. To determine if scales are suitable for studying the growth of pacu, we analyzed the relation between standard length (Sl) and the radius of the scales through linear regression. The period of annuli formation was determined analyzing the variations in the marginal increment and evaluating the consistency of the readings through the analysis of the coefficient of variations (CVs) for the average standard lengths of each age (number of rings) observed in the scales. The relationship between Ls of the fish and the radius of the scales showed that scales can be used to study the age and growth of P. mesopotamicus (R= 0.79). CVs were always below 20%, demonstrating the consistency of the readings. Annuli formation occurred in February, probably related to trophic migration that occurs in this month in the region. Equations that represents the growth in length obtained for P. mesopotamicus are Sl=50.00*[1-exp-0.18(t-(-3.00)] for males and Sl=59.23*[1-exp-0.14(t-(-3.36)] for females. The growth parameters obtained in this study were lower compared to other studies previously conducted for the same species and can related to overexploitation that species is submitted by fishing in the region. These values show also that females of pacu attain greater asymptotic length than males that growth faster.

The role of the right parietal cortex in sound localization: a chronometric single pulse transcranial magnetic stimulation study.

Auditory spatial functions, including the ability to discriminate between the positions of nearby sound sources, are subserved by a large temporo-parieto-frontal network. With the aim of determining whether and when the parietal contribution is critical for auditory spatial discrimination, we applied single pulse transcranial magnetic stimulation on the right parietal cortex 20, 80, 90 and 150 ms post-stimulus onset while participants completed a two-alternative forced choice auditory spatial discrimination task in the left or right hemispace. Our results reveal that transient TMS disruption of right parietal activity impairs spatial discrimination when applied at 20 ms post-stimulus onset for sounds presented in the left (controlateral) hemispace and at 80 ms for sounds presented in the right hemispace. We interpret our finding in terms of a critical role for controlateral temporo-parietal cortices over initial stages of the building-up of auditory spatial representation and for a right hemispheric specialization in integrating the whole auditory space over subsequent, higher-order processing stages.

Large Time-Varying Parameter VARs

In this paper we develop methods for estimation and forecasting in large timevarying parameter vector autoregressive models (TVP-VARs). To overcome computational constraints with likelihood-based estimation of large systems, we rely on Kalman filter estimation with forgetting factors. We also draw on ideas from the dynamic model averaging literature and extend the TVP-VAR so that its dimension can change over time. A final extension lies in the development of a new method for estimating, in a time-varying manner, the parameter(s) of the shrinkage priors commonly-used with large VARs. These extensions are operationalized through the use of forgetting factor methods and are, thus, computationally simple. An empirical application involving forecasting inflation, real output, and interest rates demonstrates the feasibility and usefulness of our approach.

Model Switching and Model Averaging in Time- Varying Parameter Regression Models

This paper investigates the usefulness of switching Gaussian state space models as a tool for implementing dynamic model selecting (DMS) or averaging (DMA) in time-varying parameter regression models. DMS methods allow for model switching, where a different model can be chosen at each point in time. Thus, they allow for the explanatory variables in the time-varying parameter regression model to change over time. DMA will carry out model averaging in a time-varying manner. We compare our exact approach to DMA/DMS to a popular existing procedure which relies on the use of forgetting factor approximations. In an application, we use DMS to select different predictors in an in ation forecasting application. We also compare different ways of implementing DMA/DMS and investigate whether they lead to similar results.