Avaliação energética de um sistema de refrigeração por absorção utilizando gás de aterro e gás natural

The current technological development made by the absorption refrigeration system is an economic and ambient alternative in comparison to the vapor cycle, possessing an advantage that uses thermal energy that is less noble. Chillers of absorption are used widely in the air conditioned industries, because they can be set in motion through hot water vapors that burn natural gas, solar energy, biomasses amongst others instead of electricity. These systems allow it to reduce the tips of electric demand and balance the rocking of energy demand. This work has had a main objective to simulate a absorption refrigeration cycle with lithium-water bromide solution using biogas of sanitary landfill, and mixtures of this with natural gas. These results shown to the energy viability of the system burning biogas and its mixtures with natural gas in the generator, when compared with equipments that uses traditional fuels (natural gas, oil diesel, amongst others), for operation the commercial chillers with 15 kW of the refrigeration capacity and temperature of the water in the entrance of 14°C and the exit of 7°C.

Municipal solid waste management in the Caribbean: a benefit-cost analysis

Includes bibliography

Incorporation of dithiooxamide as a complexing agent into cellulose for the removal and pre-concentration of Cu(II) and Cd(II) ions from natural water samples

The present study describes the incorporation of a complexing agent, dithiooxamide, into microcrystalline cellulose for use in the pre-concentration of Cu(II) and Cd(II) ions from aqueous samples. The FTIR spectrum of the adsorbent exhibited an absorption band in the region of 800 cm-1, which confirmed the binding of the silylating agent to the matrix. Elemental analysis indicated the amount of 0.150 mmol g-1 of the complexing agent. The adsorption data were fit to the modified Langmuir equation, and the maximum amount of metal species extracted from the solution, Ns, was determined to be 0.058 and 0.072 mmol g-1 for Cu(II) and Cd(II), respectively. The covering fraction φ, which was 0.39 and 0.48 for Cu(II) and Cd(II), respectively, was used to estimate a 1:2 (metal:ligand) ratio in the formed complex, and a binding model was proposed based on this information. The adsorbent was applied in the pre-concentration of natural water samples and exhibited an enrichment factor of approximately 50-fold for the species studied, which enabled its use in the analysis of trace metals in aqueous samples. The system was validated by the analysis of certified standard (1643e), and the adsorbent was stable for more than 20 cycles, thus enabling its safe reutilization. © 2012 Elsevier B.V. All rights reserved.

Electrochemical oxidation of wastewater containing aromatic amines using a flow electrolytic reactor

Aromatic amines are environmental pollutants and represent one of the most important classes of industrial and natural chemicals. Some types of complex effluents containing these chemical species, mainly those originated from chemicals plants are not fully efficiently treated by conventional processes. In this work, the use of electrochemical technology through an electrolytic pilot scale flow reactor is considered for treatment of wastewater of a chemical industry manufacturer of antioxidant and anti-ozonant substances used in rubber. Experimental results showed that was possible to remove between 65% and 95% of apparent colour and chemical oxygen demand removal between 30 and 90% in 60 min of treatment, with energy consumption rate from 26 kWh m-3 to 31 kWh m-3. Absorbance, total organic carbon and toxicity analyses resulted in no formation of toxic by-products. The results suggest that the presented electrochemical process is a suitable method for treating this type of wastewater, mainly when pre-treated by aeration. Copyright © 2013 Inderscience Enterprises Ltd.

Análise técnico-econômica da utilização de um gerador à gás natural em um sistema de cogeração: estudo de caso

Pós-graduação em Engenharia Mecânica - FEG

Preparação e caracterização de compósitos obtidos a partir de borracha natural com raspa de couro visando aplicações industriais

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Avaliação da viabilidade do lodo de esgosto como recondicionante de solos agrícolas, após processo de atenuação natural, por meio de diferentes bioensaios

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Síntese de pigmentos zeolíticos a partir de zeólita A derivada de rejeito de caulim da Amazônia

Pigmentos tipo ultramar foram sintetizados com sucesso a partir de zeólita NaA derivada de caulim e rejeito de caulim. Tal rejeito tem sido uma excelente fonte de silício e alumínio na síntese de zeólitas, por ser uma matéria-prima “natural” com alta concentração de caulinita e baixos teores de impurezas, além do menor custo em comparação àquelas matérias-primas industrializadas. A zeólita NaA derivada de tal rejeito apresenta características estruturais favoráveis a síntese de pigmentos ultramar, sua estrutura encapsula as espécies de enxofre formadas, que agem como cromóforos, e impedem que essas espécies se oxidem e seja liberado elevados teores de gases tóxicos durante a reação. Zeólita NaA foi misturada com enxofre e carbonato de sódio em diferentes proporções com o objetivo de verificar a influência dessa variação na cor e na tonalidade dos pigmentos. Após calcinação a 500 °C por 5 horas os produtos foram caracterizados por DRX, FRX e Raman, além da classificação visual por cor e tonalidade por meio de fotografias. O resultado foi produtos com coloração que variaram do azul ao verde com diferentes tonalidades, ambas influenciadas pela quantidade de aditivos, pela taxa de resfriamento após calcinação e pela granulometria. Assim, pode-se dizer que quantidades diferentes dos mesmos aditivos na mesma matriz zeolítica proporcionam aumento de intensidade da cor, que a taxa de resfriamento após calcinação e granulometria da matriz zeolítica provoca mudança da cor. A partir de DRX foi observado que a estrutura da zeólita NaA não é transformada para o tipo sodalita, como normalmente observado na literatura. Por espectroscopia Raman foram identificadas as espécies de enxofre responsáveis pela coloração no pigmento zeolítico, sendo: S₆ ^2- o responsável pela cor amarela e o S₃^- pela cor azul, e que a mistura dos dois resultou na cor verde, que predominou nesse trabalho. Por fim, o aproveitamento de rejeito de caulim na produção de pigmentos zeolíticos parece ser uma boa proposta de produção sustentável.

Obtenção de compósitos de borracha natural com resíduo industrial de couro reticulados com diferentes peróxidos

Pós-graduação em Ciência e Tecnologia de Materiais - FC

Caracterização do compósito obtido a partir de borracha natural com negro e resíduos de couro aplicado como pisos e revestimentos

Pós-graduação em Ciência e Tecnologia de Materiais - FC

Relações entre produção de biogás em aterro sanitário e variações no potencial elétrico natural

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Análise comparativa entre a produção de biogás em aterro controlado e variações no potencial elétrico natural por meio de perfilagem geofísica

This work aims to analyze data from a Natural Electric Potential landfill type ditch located in Cordeirópolis (SP). The procedure measures initially involved the assembly and installation of an apparatus cables, sensors and drain geophysical measurements and flow rate of biogas in a ditch later filled by solid waste. Biogas is a product of degradation of organic matter in waste by the action of microorganisms in an anaerobic environment. Its features high methane content in the gas potentially usable as fuel in energy generation systems or steam. The study area is characterized by clayey soil composition change from the diabase sill correlated to the event Serra Geral Formation siltstones overlapping Tatuí with groundwater level site around 50m. The cables were installed vertically in parallel with drain gas manifold, which allowed the collection of data by the technique geophysical logging every 15 days over a period of eight months. For data analysis we used four parameters in the study, the closing time of the ditch, natural electric potential, the flow velocity of biogas and rain. With the tabulated data plots were constructed for each collection day showing values in the range of the cable is in contact with waste (200 cm - 400 cm) and range of the cable in contact with the soil (600 cm - 800 cm). Subsequently graphs were generated with the period of eight months to analyze the data tabulated. A statistical correlation data, which show the influence of rainfall on the production of biogas. The results were satisfactory and demonstrated the feasibility of the research method in studies for the feasibility analysis for the capture of biogas energy

Evaluation of the pre-inoculum utilization in biosurfactant production by solid-state fermentation

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Aproveitamento de sementes de abóboras (Cucurbita sp) como fonte alimentar

Brazil processes much of its fruit by producing natural juices, candy preserves, extracts and pulps; however, almost 60% of their total weight derives from peels, leaves and seeds. As a result, the emphasis lies most strongly on the use of waste, especially waste that is not commonly used by the food industry or by consumers. The use of seeds would increase the viable sources of raw materials, lower operating costs of industries and would promote the development of new food products, since they are our main sources of protein, fat, fiber, functional compounds, vitamins and minerals salts. This paper presents alternatives for the use of pumpkin seeds (Cucurbita sp), which are often underutilized or discarded. It also demonstrates the bioactive and anti-nutritional compounds and their health effects.

Strategies to improve the mechanical properties of starch-based materials: plasticization and natural fibers reinforcement

Biodegradable polymers are starting to be introduced as raw materials in the food-packaging market. Nevertheless, their price is very high. Starch, a fully biodegradable and bioderived polymer is a very interesting alternative due to its very low price. However, the use of starch as the polymer matrix for the production of rigid food packaging, such as trays, is limited due to its poor mechanical properties, high hidrophilicity and high density. This work presents two strategies to overcome the poor mechanical properties of starch. First, the plasticization of starch with several amounts of glycerol to produce thermoplastic starch (TPS) and second, the production of biocomposites by reinforcing TPS with promising fibers, such as barley straw and grape waste. The mechanical properties obtained are compared with the values predicted by models used in the field of composites; law of mixtures, Kerner-Nielsen and Halpin-Tsai. To evaluate if the materials developed are suitable for the production of food-packaging trays, the TPS-based materials with better mechanical properties were compared with commercial grades of oil-based polymers, polypropylene (PP) and polyethylene-terphthalate (PET), and a biodegradable polymer, polylactic acid (PLA).