P-n junction organic photovoltaics fabricated by all solution processing

We have prepared p-n junction organic photovoltaic cells using an all solution processing method with poly(3-hexylthiophene) (P3HT) as the donor and phenyl-C 61-butyric acid methyl ester (PCBM) as the acceptor. Interdigitated donor/acceptor interface morphology was observed in the device processed with the lowest boiling point solvent for PCBM used in this study. The influences of different solvents on donor/acceptor morphology and respective device performance were investigated simultaneously. The best device obtained had characteristically rough interface morphology with a peak to valley value ∼15 nm. The device displayed a power conversion efficiency of 1.78%, an open circuit voltage (V oc) 0.44 V, a short circuit current density (J sc) 9.4 mA/cm 2 and a fill factor 43%.

Solution chemistry impacts on the seawater neutralisation process: Benefits of nanofiltered seawater and reverse osmosis brine

It is well known that the neutralisation of Bayer liquor with seawater causes the precipitation of stable alkaline products and a reduction in pH and dissolved metal concentrations in the effluent. However, there is limited information available on solution chemistry effects on the stability and reaction kinetics of these precipitates. This investigation shows the influence of reactive species (magnesium and calcium) in seawater on precipitate stabilities and volumetric efficiencies during the neutralisation of bauxite refinery residues. Correlations between synthetic seawater solutions and real samples of seawater (filtered seawater, nanofiltered seawater and reverse osmosis brine) have been made. These investigations have been used to confirm that alternative seawater sources can be used to increase the productivity potential of the neutralisation process with minimal implications on the composition and stability of precipitates formed. The volume efficiency of the neutralisation process using synthetic analogues has been shown to be almost directly proportional with the concentration of magnesium. This was further confirmed in the nanofiltered seawater and reverse osmosis brine that showed increases in the efficiency of neutralisation by factors of 3 and 2 compared to seawater, which corresponds with relatively the same increase in the concentration of magnesium in these alternative seawater sources. An assessment of the chemical stability of the precipitates, volumetric efficiency, and discharge water quality have been determined using numerous techniques that include pH, conductivity, inductively coupled plasma optical emission spectroscopy, infrared spectroscopy, thermogravimetric analysis coupled to mass spectrometry and X-ray diffraction. Correlations between synthetic solution compositions and alternative seawater sources have been used to determine if alternative seawater sources are potential substitutes for seawater based on improvements in productivity, implementation costs, savings to operations and environmental benefits.

An Electron-Accepting Chromophore Based on Fluorene and Naphthalenediimide Building Blocks for Solution-Processable Bulk Heterojunction Devices

We have designed, synthesized and utilized a new non-fullerene electron acceptor, 9,9′-(9,9-dioctyl-9H-fluorene-2,7-diyl)bis(2,7-dioctyl-4-(octylamino)benzo[lmn][3,8]phenanthroline-1,3,6,8(2H,7H)-tetraone) (B2), for use in solution-processable bulk-heterojunction devices. B2 is based on a central fluorene moiety, which was capped at both ends with an electron-accepting naphthalenediimide functionality. B2 exhibited excellent solubility (>30 mg mL−1 in chloroform), high thermal and photochemical stability, and appropriate energy levels for use with the classical polymer donor regioregular poly(3-hexylthiophene). A power conversion efficiency of 1.16 % was achieved for primitive bulk-heterojunction devices with a high fill factor of approximately 54 %.

Conjoint use of Dibenzosilole and Indan-1,3-dione Functionalities to Prepare an Efficient Non-Fullerene Acceptor for Solution-Processable Bulk-Heterojunction Solar Cells

A solution-processable, non-fullerene electron acceptor, 2,2′-(((5,5-dioctyl-5 H-dibenzo[b,d]silole-3,7-diyl)bis(thiophene-5,2-diyl))bis(methanylylidene))bis(1 H-indene-1,3(2 H)-dione) (called N5) comprised of dibenzosilole and 1,3-indanedione building blocks was designed, synthesized, and fully characterized. N5 is highly soluble in various organic solvents, has high thermal stability, and has energy levels matching those of archetypal donor poly(3-hexylthiophene). Solution-processable, bulk-heterojunction solar cells afforded promising power conversion efficiency of 2.76 % when N5 was used as a non-fullerene electron acceptor along with the conventional donor polymer poly(3-hexylthiophene). As per our knowledge, the material reported herein is the first example in the literature where synchronous use of such building blocks is demonstrated in the design an efficient, non-fullerene acceptor.

Small-angle neutron scattering study of micellar structures of dimeric surfactants

Dimeric or gemini surfactants consist of two hydrophobic chains and two hydrophilic head groups co; valently connected by a hydrocarbon spacer. Small-angle neutron scattering measurements from bis-cationic C16H33N+(CH3)(2)-(CH2)(m)-N+(CH3)(2)C(16)H(33)2Br(-) dimeric surfactants, referred to-as 16-m-16, for different length of hydrocarbon spacers m-3-6, 8, 10, and 12, are reported. The measurements have been carried out at various concentrations: C=2.5 and 10 mM for all m and C=30 and 50 mM for m greater than or equal to 5. It is found that micellar structure depends on the length of the spacer. Micelles are disks for m=3, cylindrical for m=4, and prolate ellipsoidals for other values of m. These structural results are in agreement with the theoretical predictions based on the packing parameter. It has also been observed that conformation of the spacer and the hydrophobic chains in the interior of the micelle change as the length of the spacer is increased. The concentration dependence for m greater than or equal to 5 shows that the effect of surfactant concentration on the size of the micelle is more pronounced for m=5 and 12 than for the intermediate spacers. The fractional charge on the micelle increases with the increase in spacer length and decreases when the concentration is increased.

Evidence of clustering in an aqueous electrolyte solution: a small-angle X-ray scattering study

The work reported hen was motivated by a desire to verify the existence of structure - specifically MP-rich clusters induced by sodium bromide (NaBr) in the ternary liquid mixture 3-methylpyridine (Mf) + water(W) + NaBr. We present small-angle X-ray scattering (SAXS) measurements in this mixture. These measurements were obtained at room temperature (similar to 298 K) in the one-phase region (below the relevant lower consolute points, T(L)s) at different values of X (i.e., X = 0.02 - 0.17), where X is the weight fraction of NaBr in the mixture. Cluster-size distribution, estimated on the assumption that the clusters are spherical, shows systematic behaviour in that the peak of the distribution shifts rewards larger values of cluster radius as X increases. The largest spatial extent of the clusters (similar to 4.5 nm) is seen at X = 0.17. Data analysis assuming arbitrary shapes and sizes of clusters gives a limiting value of cluster size (- 4.5 nm) that is not very sensitive to X. It is suggested that the cluster size determined may not be the same as the usual critical-point fluctuations far removed from the critical point (T-L). The influence of the additional length scale due to clustering is discussed from the standpoint of crossover from Ising to mean-field critical behaviour, when moving away from the T-L.

An Approximate Solution Of One-Dimensional Piston Problem

A new theory of shock dynamics has been developed in the form of a finite number of compatibility conditions along shock rays. It has been used to study the growth or decay of shock strength for accelerating or decelerating piston starting with a nonzero piston velocity. The results show good agreement with those obtained by Harten's high resolution TVD scheme.

Synthesis of some copper(II)-chelating (dialkylamino)pyridine amphiphiles and evaluation of their esterolytic capacities in cationic micellar media

Three new (dialkylamino)pyridine (DAAP)-based ligand amphiphiles 3-5 have been synthesized. All of the compounds possess a metal ion binding subunit in the form of a 2,6-disubstituted DAAP moiety. In addition, at least one ortho-CH2OH substituent is present in all the ligands. Complex formation by these ligands with various metal ions were examined under micellar conditions, but only complexes with Cu(II) ions showed kinetically potent esterolytic capacities under micellar conditions. Complexes with Cu(II) were prepared in host comicellar cetyltrimethylammonium bromide (CTABr) media at pH 7.6. Individual complexes were characterized by UV-visible absorption spectroscopy and electron paramagnetic resonance spectroscopy. These metallomicelles speed the cleavage of the substrates p-nitrophenyl hexanoate or p-nitrophenyl diphenyl phosphate. To ascertain the nature of the active esterolytic species, the stoichiometries of the respective Cu(II) complexes were determined from the kinetic version of Job's plot. In all the instances, 2:1 complex ligand/Cu(II) ion are the most kinetically competent species. The apparent pK(a) values of the Cu(II)-coordinated hydroxyl groups of the ligands 3, 4, and 5, in the comicellar aggregate, are 7.8, 8.0, and 8.0, respectively, as estimated from the rate constant vs pH: profiles of the ester cleavage reactions. The nucleophilic metallomicellar reagents and the second-order "catalytic" rate constants toward esterolysis of the substrate p-nitrophenyl hexanoate (at 25 degrees C, pH 7.6) are 37.5 for 3, 11.4 for 4, and 13.8 for 5. All catalytic systems comprising the coaggregates of 3, 4, or 5 and CTABr demonstrate turnover behavior in the presence of excess substrate.

Crossover from Ising to mean-field critical behavior in an aqueous electrolyte solution

The near-critical behavior of the susceptibility deduced from light-scattering measurements in a ternary liquid mixture of 3-methylpyridine, water, and sodium bromide has been determined. The measurements have been performed in the one-phase region near the lower consolute points of samples with different concentrations of sodium bromide. A crossover from Ising asymptotic behavior to mean-field behavior has been observed. As the concentration of sodium bromide increases, the crossover becomes more pronounced, and the crossover temperature shifts closer to the critical temperature. The data are well described by a model that contains two independent crossover parameters. The crossover of the susceptibility critical exponent γ from its Ising value γ=1.24 to the mean-field value γ=1 is sharp and nonmonotonic. We conclude that there exists an additional length scale in the system due to the presence of the electrolyte which competes with the correlation length of the concentration fluctuations. An analogy with crossover phenomena in polymer solutions and a possible connection with multicritical phenomena is discussed.

A 3-hour quantitative comparison of glucose-based versus rice-based oral rehydration solution intake by children with diarrhoea in Port Moresby General Hospital

Measurements were made of the intake of a WHO/UNICEF glucose-based and a rice cereal-based oral rehydration solution (ORS) by children with diarrhoea. Twenty children who presented to the Children's Outpatient Department at Port Moresby General Hospital with acute diarrhoea and mild dehydration were randomly assigned to an ORS and measurements were taken over the following 3 hours. For data analysis, the patients were paired by weight. Testing the means of the paired samples by t test showed that there was no significant difference between the amount of rice ORS and the amount of glucose ORS taken over 3 hours. The discovery of oral rehydration solution (ORS) for the treatment of diarrheal disease has been heralded as the most important medical discovery of the century. Cereal-based ORS is able to decrease stool output and the duration of diarrheal illness more than the standard glucose-based ORS, through the increased absorption provided by oligosaccharides without the imposition of a greater osmotic penalty. Moreover, the peptides in cereals enhance amino acid and water absorption, while providing nutritional benefits. UNICEF's glucose-based ORS is becoming more widely used in Papua New Guinea (PNG). 20 children aged 6-37 months (mean age, 15 months) who presented to the Children's Outpatient Department at Port Moresby General Hospital during September-October 1993 with acute diarrhea and mild dehydration were randomly assigned to receive either a rice-based ORS or standard glucose ORS, and measurements were taken over the following 3 hours. The patients were paired by weight for analysis. No statistically significant difference was found between the amount of rice ORS and the amount of glucose ORS taken over 3 hours.

Acceptability of a rice-based oral rehydration solution in Port Moresby General Hospital's Children's Outpatient Department

The guardians of children brought to the Port Moresby General Hospital's Children's Outpatient Department with a chief complaint of diarrhoeal disease were questioned regarding their preference of glucose-based vs rice-based oral rehydration solution (ORS) in order to determine the acceptability of a rice-based ORS. Of the 93 guardians interviewed, greater than 60% preferred the glucose-based solution in its mixability, appearance and taste, and 65% initially reported that their children preferred the taste of the glucose solution. However, after a 30-minute trial, only 58% of children still preferred the glucose solution. In a country where diarrhoeal disease is a leading cause of child death and guardians are the primary health care providers, the acceptability of an ORS is critical to the morbidity and mortality of Papua New Guinea's children. Killing an estimated 2.9 million children annually, diarrheal disease is the second leading cause of child mortality worldwide. Diarrheal disease is also the second leading cause of child mortality in Papua New Guinea (PNG), killing an average 193 inpatient children per year over the period 1984-90. However, despite the high level of diarrhea-related mortality and the proven efficacy of oral rehydration therapy (ORT) in managing diarrhea-related dehydration, standardized ORT has been underutilized in PNG. The current glucose-based oral rehydration solution (ORS) does not reduce the frequency or volume of a child's diarrhea, the most immediate concern of caregivers during episodes of illness. Cereal-based ORS, made from cereals which are commonly available as food staples in most countries, better address the short-term concerns of caregivers while offering a superior nutritional profile. A sample of guardians of children brought to the Port Moresby General Hospital's Children's Outpatient Department complaining of child diarrhea were asked about their preferences on glucose-based versus rice-based ORS in order to determine the acceptability of a rice-based ORS. More than 60% of the 93 guardians interviewed preferred the glucose-based solution for its mixability, appearance, and taste. 65% initially reported that their children preferred the taste of the glucose solution. However, after a 30-minute trial, only 58% of children still preferred the glucose solution.

Solution of a System of Generalized Abel Integral Equations Using Fractional Calculus

A method is presented for obtaining useful closed form solution of a system of generalized Abel integral equations by using the ideas of fractional integral operators and their applications. This system appears in solving certain mixed boundary value problems arising in the classical theory of elasticity.

Finite Element Solution Of Surface-Tension Driven Flows In Laser Surface-Melting

Lasers are very efficient in heating localized regions and hence they find a wide application in surface treatment processes. The surface of a material can be selectively modified to give superior wear and corrosion resistance. In laser surface-melting and welding problems, the high temperature gradient prevailing in the free surface induces a surface-tension gradient which is the dominant driving force for convection (known as thermo-capillary or Marangoni convection). It has been reported that the surface-tension driven convection plays a dominant role in determining the melt pool shape. In most of the earlier works on laser-melting and related problems, the finite difference method (FDM) has been used to solve the Navier Stokes equations [1]. Since the Reynolds number is quite high in these cases, upwinding has been used. Though upwinding gives physically realistic solutions even on a coarse grid, the results are inaccurate. McLay and Carey have solved the thermo-capillary flow in welding problems by an implicit finite element method [2]. They used the conventional Galerkin finite element method (FEM) which requires that the pressure be interpolated by one order lower than velocity (mixed interpolation). This restricts the choice of elements to certain higher order elements which need numerical integration for evaluation of element matrices. The implicit algorithm yields a system of nonlinear, unsymmetric equations which are not positive definite. Computations would be possible only with large mainframe computers.Sluzalec [3] has modeled the pulsed laser-melting problem by an explicit method (FEM). He has used the six-node triangular element with mixed interpolation. Since he has considered the buoyancy induced flow only, the velocity values are small. In the present work, an equal order explicit FEM is used to compute the thermo-capillary flow in the laser surface-melting problem. As this method permits equal order interpolation, there is no restriction in the choice of elements. Even linear elements such as the three-node triangular elements can be used. As the governing equations are solved in a sequential manner, the computer memory requirement is less. The finite element formulation is discussed in this paper along with typical numerical results.

Approximate solution of u'=-A2u using a relation between exp(-tA2) and exp(itA)

Let A be a positive definite operator in a Hilbert space and consider the initial value problem for u(t) = -A(2)u. Using a representation of the semigroup exp(-A(2)t) in terms of the group exp(iAt) we express u in terms of the solution of the standard heat equation w(t) = W-yy, with initial values v solving the initial value problem for v(y) = iAv. This representation is used to construct a method for approximating u in terms of approximations of v. In the case that A is a 2(nd) order elliptic operator the method is combined with finite elements in the spatial variable and then reduces the solution of the 4(th) order equation for u to that of the 2(nd) order equation for v, followed by the solution of the heat equation in one space variable.