Testate amoebae (thecamoebians) as indicators of aquatic mine impact

The environmental impacts of a single mine often remain local, but acidic and metal-rich acid mine drainage (AMD) from the waste materials may pose a serious threat to adjacent surface waters and their ecosystems. Testate amoebae (thecamoebian) analysis was used together with lake sediment geochemistry to study and evaluate the ecological effects of sulphidic metal mines on aquatic environments. Three different mines were included in the study: Luikonlahti Cu-mine in Kaavi, eastern Finland, Haveri Cu-Au mine in Ylöjärvi, southern Finland and Pyhäsalmi Zn-Cu-S mine in Pyhäjärvi, central Finland. Luikonlahti and Haveri are closed mines, but Pyhäsalmi is still operating. The sampling strategy was case specific, and planned to provide a representative sediment sample series to define natural background conditions, to detect spatial and temporal variations in mine impacts, to evaluate the possible recovery after the peak contamination, and to distinguish the effects of other environmental factors from the mining impacts. In the Haveri case, diatom analyses were performed alongside thecamoebian analysis to evaluate the similarities and differences between the two proxies. The results of the analyses were investigated with multivariate methods (direct and indirect ordinations, diversity and distance measure indices). Finally, the results of each case study were harmonized, pooled, and jointly analyzed to summarize the results for this dissertation. Geochemical results showed broadly similar temporal patterns in each case. Concentrations of ions in the pre-disturbance samples defined the natural baseline against which other results were compared. The beginning of the mining activities had only minor impacts on sediment geochemistry, mainly appearing as an increased clastic input into the lakes at Haveri and Pyhäsalmi. The active mining phase was followed by the metallic contamination and, subsequently, by the most recent change towards decreased but still elevated metal concentrations in the sediments. Because of the delay in the oxidation of waste material and formation of AMD, the most intense, but transient metal contamination phase occurred in the post-mining period at Luikonlahti and Haveri. At Pyhäsalmi, the highest metal contamination preceded effluent mitigation actions. Spatial gradients were observed besides the temporal evolution in both the pre-disturbance and mine-impacted samples from Luikonlahti and Pyhäsalmi. The geochemical gradients varied with distance from the main source of contaminants (dispersion and dilution) and with water depth (redox and pH). The spatial extent of the highest metal contamination associated with these mines remained rather limited. At Haveri, the metallic impact was widespread, with the upstream site in another lake basin found to be contaminated. Changes in thecamoebian assemblages corresponded well with the geochemical results. Despite some differences, the general features and ecological responses of the faunal assemblages were rather similar in each lake. Constantly abundant strains of Difflugia oblonga, Difflugia protaeiformis and centropyxids formed the core of these assemblages. Increasing proportions of Cucurbitella tricuspis towards the surface samples were found in all of the cases. The results affirmed the indicator value of some already known indicator forms, but such as C. tricuspis and higher nutrient levels, but also elicited possible new ones such as D. oblonga ‘spinosa’ and clayey substrate, high conductivity and/or alkalinity, D. protaeiformis ‘multicornis’ and pH, water hardness and the amount of clastic material and Centropyxis constricta ‘aerophila’ and high metal and S concentrations. In each case, eutrophication appeared to be the most important environmental factor, masking the effects of other variables. Faunal responses to high metal inputs in sediments remained minor, but were nevertheless detectable. Besides the trophic state of the lake, numerical methods suggested overall geochemical conditions (pH, redox) to be the most important factor at Luikonlahti, whereas the Haveri results showed the clearest connection between metals and amoebae. At Pyhäsalmi, the strongest relationships were found between Ca- and S-rich present loading, redox conditions and substrate composition. Sediment geochemistry and testate amoeba analysis proved to be a suitable combination of methods to detect and describe the aquatic mine impacts in each specific case, to evaluate recovery and to differentiate between the effects of different anthropogenic and natural environmental factors. It was also suggested that aquatic mine impacts can be significantly mitigated by careful design and after-care of the waste facilities, especially by reducing and preventing AMD. The case-specific approach is nevertheless necessary because of the unique characteristics of each mine and variations in the environmental background conditions.

Metallien eluointi kelatoivasta ioninvaihtimesta

Kelatoivat ioninvaihtimet ovat yleensä makrohuokoisia hartseja, joiden avulla metalleja poistetaan ja otetaan mahdollisesti talteen teollisuuden puhdistettavista jätevirroista. Ne muodostavat metalli-ionien kanssa komplekseja runkomateriaaliin kovalenttisesti liitettyjen aktiivisten funktionaalisten ryhmiensä välityksellä. Ioninvaihtimen selektiivisyys eri metalli-ioneja kohtaan vaihtelee riippuen siihen liitetystä kelatoivasta ryhmästä. Työssä tutkitaan metallien tarttumista kelatoiviin ioninvaihtimiin, sekä niiden eluoitumista adsorbentistaan. Kelatoivat ioninvaihtimet sitovat metalli-ioneja tehokkaasti ligandiensa monihampaisuudesta johtuen. Metallien tarttuminen kelatoivaan ioninvaihtimeen ei kuitenkaan ole yksiselitteistä, vaan siihen vaikuttaa muun muassa pH yhdessä monen muun tekijän kanssa. Ioninvaihtimien selektiivisyyttä tarkastellaan työssä lähinnä kovien ja pehmeiden happojen ja emästen HSAB -teorian näkökulmasta. Regeneroinnilla ioninvaihdin saadaan jälleen alkuperäiseen muotoonsa, minkä jälkeen se voidaan käyttää uudelleen. Yleensä regenerointi suoritetaan kemiallisesti. Tässä työssä ioninvaihtimien regenerointia ja kohdemetallin eluointia tarkastellaan paitsi teoriassa, myös kokeellisessa osuudessa. Kokeellisessa osuudessa tutkitaan kuparin (Cu2+) eluoitumista kelatoivasta Dowex M-4195 kationinvaihtohartsista. Kokeissa hartsi ladattiin kuparilla erillisessä panoksessa kuparin ollessa syöttöliuoksessa kuparisulfaattina. Eluointiliuoksina käytettiin 2 ja 5 molaarista rikkihappoa, sekä 2 molaarista ammoniumhydroksidia. Eluointi suoritettiin panostoimisena kolonniajona ja eluaatista otetut näytteet analysoitiin atomiadsorptiospektrofotometrillä. Analyysitulokset esitetään läpäisykäyrinä, joiden perusteella 2M ammoniumhydroksidi on kolmesta tutkitusta eluentista tehokkain eluoimaan kuparia Dowex M-4195 hartsista.

Regioselective modification of galactose-containing polysaccharides in aqueous media

Biorefining is defined as sustainable conversion of biomass into marketable products and energy. Forests cover almost one third of earth’s land area, and account for approximately 40% of the total annual biomass production. In forest biorefining, the wood components are, in addition to the traditional paper and board products, converted into chemicals and biofuels. The major components in wood are cellulose, hemicelluloses, and lignin. The main hemicellulose in softwoods, which are of interest especially for the Nordic forest industry, is O-acetyl galactoglucomannan (GGM). GGM can be isolated in industrial scale from the waste waters of the mechanical pulping process, but is not yet today industrially utilized. In order to attain desired properties of GGM for specific end-uses, chemical and enzymatic modifications can be performed. Regioselective modifications of GGM, and other galactose-containing polysaccharides were done by oxidations, and by combining oxidations with subsequent derivatizations of the formed carbonyl or carboxyl groups. Two different pathways were investigated: activation of the C-6 positions in different sugar units by TEMPO-mediated oxidation, and activation of C-6 position in only galactose-units by oxidation catalyzed by the enzyme galactose oxidase. The activated sites were further selectively derivatized; TEMPO-oxidized GGM by a carbodiimide-mediated reaction forming amides, and GO-oxidized GGM by indium-mediated allylation introducing double or triple bonds to the molecule. In order to better understand the reaction, and to develop a MALDI-TOF-MS method for characterization of regioselectively allylated GGM, α-D-galactopyranoside and raffinose were used as model compounds. All reactions were done in aqueous media. To investigate the applicability of the modified polysaccharides for, e.g., cellulose surface functionalization, their sorption onto pulp fibres was studied. Carboxylation affects the sorption tendency significantly; a higher degree of oxidation leads to lower sorption. By controlling the degree of oxidation of the polysaccharides and the ionic strength of the sorption media, high degrees of sorption of carboxylated polysaccharides onto cellulose could, however, be obtained. Anionic polysaccharides were used as templates during laccase-catalyzed polymerization of aniline, offering a green, chemo-enzymatic route for synthesis of conducting polyaniline (PANI) composite materials. Different polysaccharide templates, such as, native GGM, TEMPO-oxidized GGM, naturally anionic κ-carrageenan, and nanofibrillated cellulose produced by TEMPO-oxidation, were assessed. The conductivity of the synthesized polysaccharide/PANI biocomposites varies depending on the polysaccharide template; κ-CGN, the anionic polysaccharide with the lowest pKa value, produces the polysaccharide/PANI biocomposites with the highest conductivity. The presented derivatization, sorption, and polymerization procedures open new application windows for polysaccharides, such as spruce GGM. The modified polysaccharides and the conducting biocomposites produced provide potential applications in biosensors, electronic devices, and tissue engineering.

Toimintamalli kuormantarkastukseen ja kaatopaikkakelpoisuuden arviointiin

Vuoden 2016 alusta alkaen astuu Suomessa voimaan orgaanisen jätteen kaatopaikkakielto, joka rajoittaa voimakkaasti biohajoavan tai muun orgaanisen aineksen sijoittamista kaatopaikalle. Kiellon tavoite on ohjata orgaaniset jätevirrat hyödyntämiskäsittelyyn ja vähentää kaatopaikkasijoituksen ympäristövaikutuksia. Tämän diplomityön tavoitteena oli orgaanisen jätteen kaatopaikkakieltoon varautumiseksi luoda toimintamalli jätekuormien vastaanottoon, tarkastukseen ja käsittelyyn Keltakankaan jätekeskuksessa. Vuonna 2016 käyttöön otettavassa toimintamallissa kaatopaikalle sijoitetaan vain kaatopaikkakelpoiseksi todistettuja teollisuuden jätteitä ja asbestijätettä, epäorgaanisia jakeita sekä sekalaisen jätteen lajittelussa tai mekaanisessa käsittelyssä syntyviä hyödyntämiskelvottomia rejektejä. Usea tällä hetkellä kaatopaikalle sijoitettava jätelaji ohjautuu vaihtoehtoiseen käsittelyyn. Toimintamallin mukaan kaikki jätekeskukseen vastaanotettavat sekalaiset jätekuormat ohjataan tarkastettavaksi, esikäsiteltäväksi ja tarvittaessa mekaaniseen lajittelulinjastoon kaatopaikkasijoittamisen sijaan. Ongelmallinen jae on hyödyntämiskelvoton PVC-muovi, joka nostaa rejektien orgaanisen aineksen pitoisuutta. Niin kauan kuin PVC:lle ei ole olemassa hyötykäyttökohdetta, se ohjautunee poikkeusluvalla jätteenkäsittelyn rejektien mukana kaatopaikalle. Aiemmin sekalaisesta jätteestä 70–80 % on sijoitettu kaatopaikalle, mutta uusi lajittelulinjasto mahdollistaa käsiteltävän jätemäärä voimakkaan kasvattamisen. Toimintamallin testausvaiheessa vastaanotetuista sekalaisista kuormista luokiteltiin 11 % energiahyödynnettäviksi kotitalousjätteen kaltaisiksi, 69 % lajittelulinjastossa käsiteltäviksi ja 20 % hyödyntämiskelvottomaksi kaatopaikkajätteeksi. Kaatopaikalle sijoitettava kokonaisjätemäärä on uuden toimintamallin myötä mahdollista puolittaa, kun sekalaisen jätteen käsittelyä lisätään ja useat muut jätelajit ohjautuvat vaihtoehtoiseen käsittelyyn.

Nutritional composition of Annona crassiflora pulp and acceptability of bakery products prepared with its flour

Annona crassiflora offers an edible fruit native to the Savanna. This study aimed to develop a flour meal from Annona crassiflora pulp; analyze the chemical composition of the fresh pulp and its flour; develop and verify the acceptance of formulations with different concentrations of the flour of Annona crassiflora pulp. Fruit used were selected and processed. The pulp was dried in an oven at 60-65 ºC/48h. We analyzed the chemical composition, and two formulations of breads were prepared with 10 and 20% Annona crassiflora pulp. The results showed that the drying of Annona crassiflora pulp enriched its nutritional value. The Annona crassiflora pulp showed important chemical components, as insoluble fibers (pulp and flour), minerals (potassium, calcium, manganese and others) and antioxidant compounds. The formulations were well-accepted in a sensory point of view and proved to be a good alternative to the exploitation of the fruit.

Kartoitus Kaakkois-Suomen jätelietteistä, lietteen tuottajista ja käsittelymenetelmistä

In this thesis the sludge of Southeastern-Finland, the companies which produce sludge and the current methods and those still in development have been surveyed. 85 % of the waste sludge from industry comes from forest industries. The sludge from municipal waste water treatment plants is mostly used as a raw material for bioplants. The sludge from forest industry is mostly incinerated. New circulation methods increase the recycling value of the waste by creating new products but they still lack a full-scale plant. The political pressure from Europe and the politics driven by the government of Finland will drive circular economy forward and thus uplifting the processing options of waste slurries. This work is divided in two parts, first contains the survey and the second contains the experimental part and the operational methods based on the survey. In the experimental part wet hard sheet waste sludge was de-watered with shaking filter and the applications for waste sludge from cellulose factory were considered. The results are, that the wet hard sheet waste sludge can be dewatered to high enough total solids content for the inteded use. Also, the cellulose waste sludge has too high Cd content in almost all of the batches to be used as a land improment.

Assessment of Energy Conservation in Indian Cement Industry and Forecasting of Co2 Emissions

Cement industry ranks 2nd in energy consumption among the industries in India. It is one of the major emitter of CO2, due to combustion of fossil fuel and calcination process. As the huge amount of CO2 emissions cause severe environment problems, the efficient and effective utilization of energy is a major concern in Indian cement industry. The main objective of the research work is to assess the energy cosumption and energy conservation of the Indian cement industry and to predict future trends in cement production and reduction of CO2 emissions. In order to achieve this objective, a detailed energy and exergy analysis of a typical cement plant in Kerala was carried out. The data on fuel usage, electricity consumption, amount of clinker and cement production were also collected from a few selected cement industries in India for the period 2001 - 2010 and the CO2 emissions were estimated. A complete decomposition method was used for the analysis of change in CO2 emissions during the period 2001 - 2010 by categorising the cement industries according to the specific thermal energy consumption. A basic forecasting model for the cement production trend was developed by using the system dynamic approach and the model was validated with the data collected from the selected cement industries. The cement production and CO2 emissions from the industries were also predicted with the base year as 2010. The sensitivity analysis of the forecasting model was conducted and found satisfactory. The model was then modified for the total cement production in India to predict the cement production and CO2 emissions for the next 21 years under three different scenarios. The parmeters that influence CO2 emissions like population and GDP growth rate, demand of cement and its production, clinker consumption and energy utilization are incorporated in these scenarios. The existing growth rate of the population and cement production in the year 2010 were used in the baseline scenario. In the scenario-1 (S1) the growth rate of population was assumed to be gradually decreasing and finally reach zero by the year 2030, while in scenario-2 (S2) a faster decline in the growth rate was assumed such that zero growth rate is achieved in the year 2020. The mitigation strategiesfor the reduction of CO2 emissions from the cement production were identified and analyzed in the energy management scenarioThe energy and exergy analysis of the raw mill of the cement plant revealed that the exergy utilization was worse than energy utilization. The energy analysis of the kiln system showed that around 38% of heat energy is wasted through exhaust gases of the preheater and cooler of the kiln sysetm. This could be recovered by the waste heat recovery system. A secondary insulation shell was also recommended for the kiln in the plant in order to prevent heat loss and enhance the efficiency of the plant. The decomposition analysis of the change in CO2 emissions during 2001- 2010 showed that the activity effect was the main factor for CO2 emissions for the cement industries since it is directly dependent on economic growth of the country. The forecasting model showed that 15.22% and 29.44% of CO2 emissions reduction can be achieved by the year 2030 in scenario- (S1) and scenario-2 (S2) respectively. In analysing the energy management scenario, it was assumed that 25% of electrical energy supply to the cement plants is replaced by renewable energy. The analysis revealed that the recovery of waste heat and the use of renewable energy could lead to decline in CO2 emissions 7.1% for baseline scenario, 10.9 % in scenario-1 (S1) and 11.16% in scenario-2 (S2) in 2030. The combined scenario considering population stabilization by the year 2020, 25% of contribution from renewable energy sources of the cement industry and 38% thermal energy from the waste heat streams shows that CO2 emissions from Indian cement industry could be reduced by nearly 37% in the year 2030. This would reduce a substantial level of greenhouse gas load to the environment. The cement industry will remain one of the critical sectors for India to meet its CO2 emissions reduction target. India’s cement production will continue to grow in the near future due to its GDP growth. The control of population, improvement in plant efficiency and use of renewable energy are the important options for the mitigation of CO2 emissions from Indian cement industries

Synthesis, structure, and redox states of homoleptic d-block metal complexes with bis-1,2,4-triazin-3-yl-pyridine and 1,2,4-triazin-3-yl-bipyridine extractants

it has been established that triazinyl bipyridines (hemi-BTPs) and bis-triazinyl pyridines (BTPs), ligands which are currently being investigated as possible ligands for the separation of actinides from lanthanides in nuclear waste, are able to form homoleptic complexes with first row transition metals such as cobalt(IT), copper(II), iron(II), manganese(II), nickel(II) and zinc(II). The metal complexes exhibit six-co-ordinate octahedral structures and redox states largely analogous to those of the related terpyridine complexes. The reactivity of the different redox states of cobalt bis-hemi-BTP complex in aqueous environments has been studied with two-phase electrochemistry by immobilisation of the essentially water-insoluble metal complexes on graphite electrodes and the immersion of this modified electrode in an aqueous electrolyte. It was found that redox potentials for the metal-centred reactions were pH-independent whereas the potentials for the ligand-centred reactions were strongly pH-dependent. The reductive degradation of these complexes has been investigated by computational methods. Solvent extraction experiments have been carried out for a range of metals and these show that cobalt(II) and nickel(II) as well as palladium(II), cadmium(II) and lead(II) were all extracted with the ligands 1e and 2c with higher distribution ratios that was observed for americium(III) under the same conditions. The implications of this result for the use of these ligands to separate actinides from nuclear waste are discussed. (c) 2005 Elsevier Ltd. All rights reserved.

Recent developments in nanostructured materials for high-performance thermoelectrics

This highlight discusses recent trends in the search for new high-efficiency thermoelectric materials. Thermoelectric materials offer considerable attractions in the pursuit of a more efficient use of existing energy resources, as they may be used to construct power-generation devices that allow useful electrical power to be extracted from otherwise waste heat. Here, we focus on the significant enhancements in thermoelectric performance that have been achieved through nanostructuring. The principal factor behind the improved performance appears to be increased phonon scattering at interfaces. This results in a substantial reduction in the lattice contribution to thermal conductivity, a low value of which is a key requirement for improved thermoelectric performance.

A multi-model evaluation of aerosols over South Asia: common problems and possible causes

Atmospheric pollution over South Asia attracts special attention due to its effects on regional climate, water cycle and human health. These effects are potentially growing owing to rising trends of anthropogenic aerosol emissions. In this study, the spatio-temporal aerosol distributions over South Asia from seven global aerosol models are evaluated against aerosol retrievals from NASA satellite sensors and ground-based measurements for the period of 2000–2007. Overall, substantial underestimations of aerosol loading over South Asia are found systematically in most model simulations. Averaged over the entire South Asia, the annual mean aerosol optical depth (AOD) is underestimated by a range 15 to 44% across models compared to MISR (Multi-angle Imaging SpectroRadiometer), which is the lowest bound among various satellite AOD retrievals (from MISR, SeaWiFS (Sea-Viewing Wide Field-of-View Sensor), MODIS (Moderate Resolution Imaging Spectroradiometer) Aqua and Terra). In particular during the post-monsoon and wintertime periods (i.e., October–January), when agricultural waste burning and anthropogenic emissions dominate, models fail to capture AOD and aerosol absorption optical depth (AAOD) over the Indo–Gangetic Plain (IGP) compared to ground-based Aerosol Robotic Network (AERONET) sunphotometer measurements. The underestimations of aerosol loading in models generally occur in the lower troposphere (below 2 km) based on the comparisons of aerosol extinction profiles calculated by the models with those from Cloud–Aerosol Lidar with Orthogonal Polarization (CALIOP) data. Furthermore, surface concentrations of all aerosol components (sulfate, nitrate, organic aerosol (OA) and black carbon (BC)) from the models are found much lower than in situ measurements in winter. Several possible causes for these common problems of underestimating aerosols in models during the post-monsoon and wintertime periods are identified: the aerosol hygroscopic growth and formation of secondary inorganic aerosol are suppressed in the models because relative humidity (RH) is biased far too low in the boundary layer and thus foggy conditions are poorly represented in current models, the nitrate aerosol is either missing or inadequately accounted for, and emissions from agricultural waste burning and biofuel usage are too low in the emission inventories. These common problems and possible causes found in multiple models point out directions for future model improvements in this important region.

Biogás no estado de São Paulo: novo potencial em um mercado restringido

O trabalho tem como objetivo apresentar o aproveitamento de biogás de aterros como uma alternativa potencial à utilização de gás natural no Estado de São Paulo. O trabalho descreve a produção de biogás e os principais desafios para levar o produto final ao mercado. São descritos os benefícios, tanto econômicos e energéticos quanto ambientais, do aproveitamento de um recurso que é geralmente esquecido. O trabalho analisará o perfil da produção de biogás de aterros no Brasil e como a regulação interage com uma indústria que em grande parte é nova. O trabalho propõe umas ideias a respeito de fontes de verbas para novos projetos, além de analisar algumas experiências internacionais. Utilizando teoria econômica, o trabalho tentará mostrar como esta fonte de energia poderia ser introduzida no mercado, mesmo sob condições econômicas desafiadoras.

Preferência alimentar e identificação das principais fontes de repasto sanguíneo de fêmeas Lutzomyia (Diptera: Psychodidae) em áreas endêmicas para leishmaniose visceral na grande Natal

Leishmaniasis are endemic diseases wild spread in the New and Old World, caused by the flagelated protozoan Leishmania. In the New World, the distribution of different forms of leishmaniasis is mostly in tropical regions. In the State of Rio Grande do Norte, Northeast Brazil, 85% of the captured sand flies fauna is Lutzomyia longipalpis. The distribution of the sand fly vector in the state overlaps with the disease distribution, where the presence of sand flies is associated with presence of animals shelters. The aim of this study was to analyse the blood meal preference of sand flies vector from the genus Lutzomyia spp. in laboratory conditions, to verify the vector life cicle at different temperatures sets and to identify the main blood meal source in endemic areas for visceral leishmaniasis (VL) at peri-urban regions of Natal. Sand flies samples were collected from the municipalities of São Gonçalo do Amarante and Nísia Floresta where female sand flies were grouped for the colony maintenance in the laboratory and for the analysis of the preferred source of sand fly blood meal in natural environment. The prevalence of blood meal preference and oviposition for the females sand flies was 97% for Cavia porcellus with oviposition of 19 eggs/female; 97% for Eqqus caballus with 19 eggs/female; 98% for human blood with 14 eggs/female; 71.3% for Didelphis albiventris with 8.4 eggs/female; 73% for Gallus gallus with 14 eggs/female; 86% for Canis familiaris with 10.3 eggs/female; 81.4% for Galea spixii with 26 eggs/female; 36% for Callithrix jachus with 15 eggs/female; 42.8% for Monodelphis domestica with 0% of oviposition. Female sand flies did not take a blood meal from Felis catus. Sand flies life cycle ranged from 32-40 days, with 21-50 oviposition rates approximately. This study also showed that at 32°C the life cycle had 31 days, at 28° C it had 50 days and at 22°C it increased to 79 days. Adjusting the temperature to 35°C the eggs did not hatch, thus blocking the life cycle. A total of 1540 sand flies were captured, among them, 1.310 were male and 230 were female. Whereas 86% of the sand flies captured were Lu. longipalpis as compared to 10.5% for Lu. evandroi and, 3.2% for L. lenti and 0.3% for Lu whitmani. The ratio between female and male sandfly was approximately 6 males to 1 female. In Nísia Floresta, 50.7% of the collected females took their blood meal from armadillo, 12.8% from human. Among the female sand flies captured in São Gonçalo do Amarante, 80 of them were tested for the Leishmania KDNA infectivity where 5% of them were infected with Leishmania chagasi. Female Lutzomyia spp. showed to have an opportunistic blood meal characteristic. The behavioral parameters seem to have a higher influence in the oviposition when compared to the level of total proteins detected in the host s bloodstream. A higher Lu. longipalpis life cycle viability was observed at 28°C. The increase of temperature dropped the life cycle time, which means that the life cycle is modified by temperature range, source of blood meal and humidity. Lu longipalpis was the most specie found in the inner and peridomiciliar environment. In Nísia Floresta, armadillos were the main source of blood meal for Lutzomyia spp. At São Gonçalo do Amarante, humans were the main source of blood meal due to CDC nets placed inside their houses

Inclusão de farinha de resíduos da indústria de filetagem de tilápias na alimentação de girinos de rã-touro (Rana Catesbeiana Shaw,1802)

The objective of this experiment was to evaluate the inclusion of meal of tilapia industrial waster in bullfrog tadpoles' diets (Rana Catesbeina Shaw, 1802). Two hundred fifty tadpoles with initial weight and length of 0,18 +/- 0,05g and 2,50 +/- 0,18 centimeters were used, respectively, they were used and distributed in 25 aquariums of 30 liter each in a complete randomized design with five treatments and five repetitions. The tadpoles were fed four times a day with diets containing 0, 5, 10 and 15% of inclusion of tilapia filleting and another diet with 0% of supplemented tilapia filleting with synthetic methionine, being supplied four times a day at ease. The experiment period was 30 days. The diets with tilapia filleting inclusion and methionine supplementation did not have influence in the final weight and length averages, feed survival and conversion of bullfrog tadpoles. It cam be used until 15% of tilapia filleting inclusion in the bullfrog tadpoles food. The synthetic methionine supplementation in diets for bullfrog tadpoles is not necessary in diets with levels over 0,471/4 of the total methionine.

Avaliação microbiológica e bromatológica da silagem ácida obtida de resíduos da indústria de filetagem de tilápia do Nilo (Oreochromis niloticus)

The experiment constituted in evaluating the acid silage prepared from Nile tilapia (Oreochromis niloticus) filletage industry residues. This silage was prepared in a filetage industry through the residues milling and 5% of ascetic acid addition and stock piling in a period up to until 201 days. Storaged silages in a period of 7, 12, 22, 27, 41, 48, 61, 75, 84, 91, 96, 110, 140, 151, 181, 187 and 201dias were evaluated. Bromatologics analyses of rude protein(PB), etereal extract (EE), humidity (UM), ashes (CZ) and microbiological analyses of Salmonella, total coliforms, faecals and Escherichia coli of the storaged silages in a period of 7, 91 and 201 days were realized. The pH was evaluated in all the storaged periods. Differences (P > 0.05) in the substance of PB, EE, UM and CZ were not observed. A linear increase in PH was observed, being stabilizing in plateau of 4.74. In relation to the microbiological analysis the presence of Salmonella, total coliforms, faecals and E. Coli were not found. Was concluded that the acid silage gotten from tilapia filetage residues produced with the use of 5% ascetic acid can be stored during 201 days without having Salmonella, total coliforms and faecals proliferation.

Rastreabilidade de farinha de vísceras de aves por isótopos estáveis em penas de frangos de corte

O objetivo deste trabalho foi detectar a presença de farinha de vísceras de aves (FV) na alimentação de frangos de corte, por meio da análise de penas por isótopos estáveis de carbono (13C/12C) e nitrogênio (15N/14N) e espectrofotometria de massas. Setecentos e vinte pintos machos Cobb foram submetidos aos seguintes tratamentos: ração vegetal (RV) à base de milho e farelo de soja, de 1 a 42 dias de idade; ração com 8% de farinha de vísceras de frango (FV), de 1 a 42 dias de idade; ração vegetal de 1 a 21 dias e ração com FV de 22 a 42 dias; ração vegetal de 1 a 35 dias e ração com FV de 36 a 42 dias; ração com FV de 1 a 21 dias, e ração vegetal de 22 a 42 dias; ração com FV de 1 a 35 dias, e ração vegetal de 36 a 42 dias. Foram colhidas amostras de penas de quatro aves por tratamento aos 7, 14, 21, 28, 35 e 42 dias de idade, que foram submetidas à análise isotópica de carbono (13C/12C) e nitrogênio (15N/14N) por espectrometria de massas. A aplicação da técnica dos isótopos estáveis de C e N a penas de frango de corte, após a utilização de farinha de vísceras na alimentação de frangos de corte, pelo período de até 21 dias, permite detectar a inclusão da FV na dieta.