SAE 1045 steel/WC-Co/Ni-Cu-Ni/SAE 1045 steel joints prepared by dynamic diffusion bonding: Microelectrochemical studies in 0.6 M NaCl solution

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Determination of the volume fraction of retained austenite in a 300m steel by heat tinting technique

Applying the Heat Tinting Technique the microestrutural characterization of a 300M steel (medium carbon steel) was accomplished. The steel was austenitized for 20 min to 900°C, followed by holding at 400°C (in the bainitic temperature), with maintenance time of the material in the temperature of 1min, 5min and 30min, aiming at the formation of a multiphase structure. Through the metallographic analysis it is verified that, with the use of this technique, it is possible the determination of the volume fraction of the present phases in the 300M steel, especially in the identification and quantification of the retained austenite. Copyright © 2007 SAE International.

Efeito da temperatura e tempo de austenitização nas transformações de fase da liga 13Cr2Ni0,1C

New classes of martensitic stainless steels, with low carbon levels, have been developed aiming to meet the needs of the petroleum industry segment. However, their use has been restricted due to the fact it is a recent development and many of its properties are still under investigation. This work determines the values of initial and final temperatures for the austenitic transformation and the initial and final temperatures of martensitic formation for alloy 13Cr2Ni0,1C, by means of dilatometric tests under continuous cooling. Based on these results the optimized conditions for quench and temper heat treatments were obtained. The microstructural characterization of the alloys under coarse fusion condition was carried out by optical microscopy and the presence of delta-ferrite in the martensitic matrix was observed.

Carbon nanotube-reinforced siloxane-PMMA hybrid coatings with high corrosion resistance

Siloxane-polymethyl methacrylate hybrid films containing functionalized multiwall carbon nanotubes (CNTs) were deposited by dip-coating on carbon steel substrates from a sol prepared by radical polymerization of methyl methacrylate and 3-methacryloxy propyl-trimethoxysilane, followed by hydrolytic co-polycondensation of tetraethoxysilane. The correlation between the structural properties and corrosion protection efficiency was studied as a function of the molar ratio of nanotubes carbon to silicon, varied in the range between 0.1% and 5%. 29Si nuclear magnetic resonance and thermogravimetric measurements have shown that hybrids containing carbon nanotubes have a similar degree of polycondensation and thermal stability as the undoped matrix and exhibit and excellent adhesion to the substrate. Microscopy and X-ray photoelectron spectroscopy results revealed a very good dispersion of carbon nanotubes in the hybrid matrix and the presence of carboxylic groups allowing covalent bonding with the end-siloxane nodes. Potentiodynamic polarization curves and electrochemical impedance spectroscopy results demonstrate that CNTs containing coatings maintain the excellent corrosion protection efficiency of the hybrids, showing even a superior performance in acidic solution. The nanocomposite structure acts as efficient corrosion barrier, increasing the total impedance by 4 orders of magnitude and reducing the current densities by more than 3 orders of magnitude, compared to the bare steel electrode. © 2013 Elsevier B.V. All rights reserved.

Estudo do efeito springback em aços avançados de alta resistência aplicados a indústria automobilística

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Caracterização microestrutural de um aço médio carbono e baixa liga (com estrutura bainítica/martensítica) via microscopia óptica

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Estudo eletroquímico da corrosividade de biodiesel para aço carbono e outros materiais metálicos usados em veículos automotores

Pós-graduação em Química - IQ

Caracterização mecânica e microestrutural de um aço de baixo carbono

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Caracterização microestrutural e de propriedades mecânicas de soldas do aço ASTM A 131 pelos processos FCAW convencional e com adição de arame frio

O trabalho aqui representado retrata de modo comparativo as características mecânicas e microestruturais de metais de solda empregando duas técnicas de soldagem uma já disseminada, FCAW (Soldagem a Arco Voltaico com Arame Tubular) e a outra é inovadora, FCAW-AF (Soldagem a Arco Voltaico com Arame Tubular com Adição de um Arame Frio não energizado) em três níveis de velocidades 6, 8 e 10 m/min. Sendo que este processo variou os diâmetros dos arames frio adicionados, entre 0.8 e 1.0 mm. O metal de base utilizado foi o aço naval ASTM 131 grau A (baixo carbono) em geometria de chapas de 150 mm x 300 mm x 9,5 mm, aplicadas em chanfro em V (Bisel de 22,5º) com ângulo somado de 45º, com leve abertura de raiz de 2,4 mm. A solda usada foi do tipo topo com a aplicação de dois passes, um passe de raiz e o passe de acabamento (ou enchimento). A fim averiguar as condições desses cordões de solda foram realizados 05 tipos de ensaios destrutivos, são eles: dobramento transversal de face, tração, tenacidade ao impacto (tipo Charpy com entalhe em V), microdureza e o ensaio metalográficos. Além das análises não destrutivas como o ensaio visual e o líquido penetrante. De maneira geral, os resultados para o processo FCAW-AF, mostraram-se compatíveis, em relação ao processo FCAW convencional, porém alguns resultados apresentaram valores de propriedades mecânicas menores. Este fato pode, muito provavelmente ter ocorrido pela presença de descontinuidade na junta pelo FCAW-AF. Quanto às caracterizações microestruturais, os resultados da junta FCAW-AF foram semelhantes os da FCAW convencional para todos os níveis estudados.

Desenvolvimento de sistemas multifuncionais baseados em híbridos orgânico-inorgânicos dopados

Pós-graduação em Química - IQ

Comparação de compósitos obtidos via RTM de resina epóxi e fibra de carbono com e sem descontinuidade nos tecidos

Technology is growing interest in the use of composites, due to the requirement of lighter materials and more resistant, factors essential to meet the project specifications and reduce the operational cost. In the production of high performance structural composites, considering the aerospace criteria, the domestic industry has shown interest in the process of resin transfer molding (RTM) for reproducibility and low cost. This process is suitable for producing components of polymeric composites with relatively simple geometries, consistent thicknesses, high quality finish with no size limitations. The objective of this work was machined carbon steel to make a matched-die tooling for RTM and produce two composite plates of epoxy resin and carbon fiber fabric with and without induced discontinuities, which were compared towards their impregnation with ultrasound, their properties via tensile tests and thermal analysis. In ultrasonic inspection, it was found good impregnation of the preform of both composites. In the thermal analysis it was possible to check the degradation temperature of the composites, the glass transition temperature and it was found that the composites showed no effective cure cycles, but presented good performance in the tensile test when compared with aluminum alloy 7050 T7451 . The results showed that the injection strategy was appropriate since the laminate exhibited a good quality for the proposed application

Implementação de um tuboexpansor na refinaria do Planalto Paulista – REPLAN com objetivo do aproveitamento da energia contida nos gases residuais do FCC – Fluid Catalytic Cracking na geração de energia elétrica

The steel type AISI 4130 (ultra-high strength steel) is an alloy of low carbon and its main alloying elements are chromium and molybdenum, which improves the toughness of the weld metal. It has numerous applications, especially where the need for high mechanical strength. It is widely used in equipment used by the aviation industry, such as cradle-tomotor, and this is the motivation for this study. Cots are of fundamental importance, because the engine supports and maintains balance in the fixed landing gear. This equipment is subjected to intense loading cycles, whose fractures caused by fatigue are constantly observed. Will be determined the effects caused by re-welding the structure of aeronautical equipment, and will also study the microstructure of the metal without welding. The studies will be done on materials used in aircraft, which was given to study. The results provide knowledge of microstructure to evaluate any type of fracture that maybe caused by fatigue. Fatigue is a major cause of aircraft accidents and incidents occurred, which makes the study of the microstructure of the metal, weld and re-solder the knowledge essential to the life of the material. The prevention and control of the process of fatigue in aircraft are critical, since the components are subjected to greater responsibility cyclic loading

Avaliação mecânica da colagem estrutural entre compósitos poliméricos e materiais metálicos utilizados em dutos petroquímicos

The development of technology for structural composites has as one of its ends form a set of materials that combine high values of mechanical strength and stiffness and low density. Today, companies like Embraer and PETROBRAS and research institutions like NASA, working with these materials with recognized advantages in terms of weight gain, increased performance and low corrosion. We have developed a systematic study to determine the bond strength between composite carbon fiber / epoxy and fiberglass / epoxy laminate both bonded to a carbon steel which are widely used in the petrochemical industry and repair. For morphological evaluation and bonding between materials of different natures, ultrasound analysis, optical microscopy and stereoscopy were performed. To simulate actual conditions, the composites were subjected to conditioning by using heat shock temperatures from -50 to 80 ° C for 1000 cycles for composite carbon fiber / epoxy composites and 2000 cycles for fiberglass / epoxy . The use of composites studied here proved to be efficient to perform repairs in metallic pipes with application petrochemical, as when exposed to sudden changes of temperature (-50 ° to 80 ° C) cycling at 1000 to 2000 times, its mechanical properties (shear and tensile) practically do not change

Alterações microestruturais decorrentes dos sucessivos reparos de solda TIG aplicados ao longo da vida útil de uma estrutura aeronáutica crítica à segurança de vôo

The steel type AISI 4130 (ultra-high strength steel) is an alloy of low carbon and its main alloying elements are chromium and molybdenum, which improves the toughness of the weld metal. It has numerous applications, especially where the need for high mechanical strength. It is widely used in equipment used by the aviation industry, such as cradle-tomotor, and this is the motivation for this study. Cots are of fundamental importance, because the engine supports and maintains balance in the fixed landing gear. This equipment is subjected to intense loading cycles, whose fractures caused by fatigue are constantly observed. Will be determined the effects caused by re-welding the structure of aeronautical equipment, and will also study the microstructure of the metal without welding. The studies will be done on materials used in aircraft, which was given to study. The results provide knowledge of microstructure to evaluate any type of fracture that maybe caused by fatigue. Fatigue is a major cause of aircraft accidents and incidents occurred, which makes the study of the microstructure of the metal, weld and re-solder the knowledge essential to the life of the material. The prevention and control of the process of fatigue in aircraft are critical, since the components are subjected to greater responsibility cyclic loading

Desenvolvimento de aplicativo de análise técnica e econômica para adaptação de uma roda d’água acionada por cima para geração de energia elétrica no meio rural

The steel type AISI 4130 (ultra-high strength steel) is an alloy of low carbon and its main alloying elements are chromium and molybdenum, which improves the toughness of the weld metal. It has numerous applications, especially where the need for high mechanical strength. It is widely used in equipment used by the aviation industry, such as cradle-tomotor, and this is the motivation for this study. Cots are of fundamental importance, because the engine supports and maintains balance in the fixed landing gear. This equipment is subjected to intense loading cycles, whose fractures caused by fatigue are constantly observed. Will be determined the effects caused by re-welding the structure of aeronautical equipment, and will also study the microstructure of the metal without welding. The studies will be done on materials used in aircraft, which was given to study. The results provide knowledge of microstructure to evaluate any type of fracture that maybe caused by fatigue. Fatigue is a major cause of aircraft accidents and incidents occurred, which makes the study of the microstructure of the metal, weld and re-solder the knowledge essential to the life of the material. The prevention and control of the process of fatigue in aircraft are critical, since the components are subjected to greater responsibility cyclic loading