Studies on Latex Reclaim and its Blends

The primary aim of this work has been to develop a cost effective process that can be operated at room temperature for developing latex reclaim with superior mechanical properties. With this objective in mind the researcher proposes to study the reclaiming action of four different chemicals on latex products waste. Waste latex products are chosen because it has a higher potential to generate good quality rubber hydrocarbon since all latex products are based on either high quality concentrated latex or creamed latex. Moreover, all latex products are only lightly crosslinked and not masticated and hence not mechanically degraded. The author also proposes to fully explore the possible application of latex reclaim in various fields..

Microbial Treatment Of Rubber Latex Centrifugation Effluent

Many of the existing methods for the treatment of rubber latex centrifugation eflluent are not only unsatisfactory in their efliciency to effect near perfect treatment in bringing down the COD to optimum level, but also time consuming and need a large landspace. As the rate of effluent generation is extremely high (20 litres for kilogram of rubber) there is a need for development of efficient system,capable of rapid reduction of COD and BOD. Though the organic load of the rubber efiluent is very high, it does not contain much processed chemicals and therefore it can be considered as a ‘biological eflluent’. Further, the ratio of the Chemical Oxygen Demand to Biological Oxygen Demand (COD/BOD) of this effluent remain almost as a constant value. According to Montgomery (1967), estimation of BOD is not ideally suited for studies on process design, treatability, control of treatment plants, setting standards for treated effluents and assessing the effect of polluting discharges on the oxygen resources of receiving waters. Hence in the present study COD was measured to determine the impact of treatment system on the effluent. In the present study, attempts were made to evaluate the efficiencies of certain methods such as packed bed reactor using immobilized microbial cells, rotating biological contactor (RBC) and activated sludge process, for rapid and efficient treatment of natural rubber latex centrifugation effluent. In addition, studies were also carn'ed out to develop a suitable bioprocess for the coagulation of skim latex, as an alternative to the presently used acid coagulation process towards reducing the pollution load, besides recovering quality rubber

MitWirkung - Zukunft gestalten

Die Diskussion in den Planungswissenschaften beschreibt den Paradigmenwechsel vom so genannten DEAD-Model (Decide-Announce-Defend) zum Tripple-D-Model (Dialogue-Decide-Deliver) und beschäftigt sich intensiv mit dem Thema Governance. Komplexe Planungsaufgaben brauchen eine Vielfalt an Lösungsideen unterschiedlicher gesellschaftlicher Gruppen. Planung verfolgt u. a. die Umsetzung der Ziele einer nachhaltigen Entwicklung, die die Einbeziehung der Öffentlichkeit (Zivilgesellschaft, Unternehmen und Bürger) verlangt. Darüber hinaus wird eine Erweiterung der Perspektive über Verfahren und Steuerungsformen hinaus auf Akteure und Prozesse gefordert. Räumliche Entwicklungen sollen stärker im Zusammenhang mit Entscheidungsfindungsprozesse untersucht werden. Die Dissertation ergänzt eine wirkungsorientierte Perspektive, die Wirkungen, sowohl räumliche als auch soziale, in den Mittelpunkt der Betrachtung stellt. Sie stützt sich auf Beobachtungen, dass klassisches Projektmanagement für erfolgreiche Planungsprozesse nicht ausreicht, sondern zusätzlich Prozessmanagement braucht. Mit der Weiterentwicklung der partizipativen Planung, die zusätzlich in den Kontext gesellschaftlicher Lernprozesse und zukunftsfähiger Veränderungen gesellschaftlicher Bedingungen gestellt wird, ergänzt die Dissertation planungswissenschaftliche Theorien. Aus einem fachübergreifenden Blickwinkel wird die räumliche Planung in die Reihe von Management- und Organisationswissenschaften eingeordnet. Ausgehend von der Frage, welche räumlichen und sozialen Wirkungen durch Beteiligungsprozesse unter welchen Bedingungen erzielt werden, wurden Fallstudien aus der Wasserwirtschaft und ihre Prozessbiografien umfassend evaluiert. Als Evaluierungsmethode wurde ein von der EU-Kommission empfohlener Evaluierungsrahmen gewählt, der sowohl den Prozess selbst, seine Rahmenbedingungen und Durchführung, als auch Wirkungen analysiert und bewertet. Auf der Grundlage der Ergebnisse und theoretischer Erkenntnisse, vorrangig aus der Evaluationsforschung, wird ein umfassender Beteiligungsansatz konzipiert. Dabei handelt es sich um ein offenes Gerüst, in das sich bewährte und innovative Elemente strategisch gezielt integrieren lassen. Die Struktur verbindet verschiedene Beteiligungswerkzeuge unterschiedlicher Intensitäten und für unterschiedliche Zielgruppen zu einem Gesamtkonzept, mit dem Ziel, möglichst die gewünschten Wirkungen zu erreichen. Wesentlich an dem Ansatz ist, dass bereits das Prozessdesign unter Mitwirkung von Projektträgern, Beratern und Schlüsselakteuren erfolgt. Die partizipative Beteiligungsplanung bedeutet somit Klärung der Vorgehensweise und gleichzeitig Bewusstseins- und Kompetenzerweiterung der verantwortlichen Akteure. Im Ausblick werden künftige Forschungsaufgaben im Bereich der Mitwirkung in der räumlichen Planung formuliert und Handlungsmöglichkeiten aufgezeigt, um Partizipation als Teil planerischer „Alltagskultur“ weiterzuentwickeln. Dies erfolgt vor dem Hintergrund der Bedeutung von Partizipation und Bildung als Umsetzungsstrategie von Ideen der Landschaftsentwicklung und Nachhaltigkeit.

Large-Size AlGaN/GaN HEMT Large-Signal Electrothermal Characterization and Modeling for Wireless Digital Communications

The rapid growth in high data rate communication systems has introduced new high spectral efficient modulation techniques and standards such as LTE-A (long term evolution-advanced) for 4G (4th generation) systems. These techniques have provided a broader bandwidth but introduced high peak-to-average power ratio (PAR) problem at the high power amplifier (HPA) level of the communication system base transceiver station (BTS). To avoid spectral spreading due to high PAR, stringent requirement on linearity is needed which brings the HPA to operate at large back-off power at the expense of power efficiency. Consequently, high power devices are fundamental in HPAs for high linearity and efficiency. Recent development in wide bandgap power devices, in particular AlGaN/GaN HEMT, has offered higher power level with superior linearity-efficiency trade-off in microwaves communication. For cost-effective HPA design to production cycle, rigorous computer aided design (CAD) AlGaN/GaN HEMT models are essential to reflect real response with increasing power level and channel temperature. Therefore, large-size AlGaN/GaN HEMT large-signal electrothermal modeling procedure is proposed. The HEMT structure analysis, characterization, data processing, model extraction and model implementation phases have been covered in this thesis including trapping and self-heating dispersion accounting for nonlinear drain current collapse. The small-signal model is extracted using the 22-element modeling procedure developed in our department. The intrinsic large-signal model is deeply investigated in conjunction with linearity prediction. The accuracy of the nonlinear drain current has been enhanced through several issues such as trapping and self-heating characterization. Also, the HEMT structure thermal profile has been investigated and corresponding thermal resistance has been extracted through thermal simulation and chuck-controlled temperature pulsed I(V) and static DC measurements. Higher-order equivalent thermal model is extracted and implemented in the HEMT large-signal model to accurately estimate instantaneous channel temperature. Moreover, trapping and self-heating transients has been characterized through transient measurements. The obtained time constants are represented by equivalent sub-circuits and integrated in the nonlinear drain current implementation to account for complex communication signals dynamic prediction. The obtained verification of this table-based large-size large-signal electrothermal model implementation has illustrated high accuracy in terms of output power, gain, efficiency and nonlinearity prediction with respect to standard large-signal test signals.

WAIS Seminar:Evaluating the Cognitive Side of Information Interaction

Abstract In this talk, I'll focus on the work we've been doing on evaluating the cognitive side of dealing with information resources and increasingly complex user interfaces. While we can build increasingly powerful user interfaces, they often come at the cost of simple design and ease of use. I'll describe two specific studies: 1) work on the ORCHID project focused on measuring mental workload during tasks using fNIRS (a blood-oxygen-based brain scanner), and 2) a evaluation metric for measuring how much people learn during tasks. Together these provide advances towards understanding the cognitive side of information interaction, in working towards building better tools for users.

Aplicació d'algoritmes genètics en l'optimització dels processos de fabricació del paper

La creciente preocupación y concienciación de la sociedad respecto el medio ambiente, y en consecuencia la legislación y regulaciones generadas inducen a la modificación de los procesos productivos existentes en la industria química. Las configuraciones iniciales deben modificarse para conseguir una mayor integración de procesos. Para este fin se han creado y desarrollado diferentes metodologías que deben facilitar la tarea a los responsables del rediseño. El desarrollo de una metodología y herramientas complementarias es el principal objetivo de la investigación aquí presentada, especialmente centrada en el desarrollo y la aplicación de una metodología de optimización de procesos. Esta metodología de optimización se aplica sobre configuraciones de proceso existentes y pretende encontrar nuevas configuraciones viables según los objetivos de optimización fijados. La metodología tiene dos partes diferenciadas: la primera se basa en un simulador de procesos comercial y la segunda es la técnica de optimización propiamente dicha. La metodología se inicia con la elaboración de una simulación convenientemente validada que reproduzca el proceso existente, en este caso una papelera no integrada que produce papel estucado de calidad, para impresión. A continuación la técnica de optimización realiza una búsqueda dentro del dominio de los posibles resultados, en busca de los mejores resultados que satisfazcan plenamente los objetivos planteados. Dicha técnica de optimización está basada en los algoritmos genéticos como herramienta de búsqueda, junto a un subprograma basado en técnicas de programación matemática para el cálculo de resultados. Un número reducido de resultados son finalmente escogidos y utilizados para modificar la simulación existente fijando la redistribución de los flujos del proceso. Los resultados de la simulación del proceso determinan en último caso la viabilidad técnica de cada reconfiguración planteada. En el proceso de optimización, los objetivos están definidos en una función objetivo dentro de la técnica de optimización. Dicha función rige la búsqueda de resultados. La función objetivo puede ser individual o una combinación de objetivos. En el presente caso, la función persigue una minimización del consumo de agua y una minimización de la pérdida de materia prima. La optimización se realiza bajo restricciones para alcanzar este objetivo combinado en forma de una solución de compromiso. Producto de la aplicación de esta metodología se han obtenido resultados interesantes que significan una mejora del cierre de circuitos y un ahorro de materia prima, sin comprometer al mismo tiempo la operabilidad del proceso producto ni la calidad del papel.

High yield production of a soluble bifidobacterial β-galactosidase (BbgIV) inE. coliDH5α with improved catalytic efficiency for the synthesis of prebiotic galactooligosaccharides

The bifidobacterial β-galactosidase (BbgIV) was produced in E. coli DH5α at 37 and 30 °C in a 5 L bioreactor under varied conditions of dissolved oxygen (dO2) and pH. The yield of soluble BbgIV was significantly (P < 0.05) increased once the dO2 dropped to 0–2% and remained at such low values during the exponential phase. Limited dO2 significantly (P < 0.05) increased the plasmid copy number and decreased the cells growth rate. Consequently, the BbgIV yield increased to its maximum (71–75 mg per g dry cell weight), which represented 20–25% of the total soluble proteins in the cells. In addition, the specific activity and catalytic efficiency of BbgIV were significantly (P < 0.05) enhanced under limited dO2 conditions. This was concomitant with a change in the enzyme secondary structure, suggesting a link between the enzyme structure and function. The knowledge generated from this work is very important for producing BbgIV as a biocatalyst for the development of a cost-effective process for the synthesis of prebiotic galactooligosaccharides from lactose.

Remoção de hidrocarbonetos do gás natural visando o ajuste do índice de metano

The use of the natural gas is growing year after year in the whole world and also in Brazil. It is verified that in the last five years the profile of natural gas consumption reached a great advance and investments had been carried through in this area. In the oil industry, the use of the natural gas for fuel in the drive of engines is usual for a long date. It is also used to put into motion equipment, or still, to generate electric power. Such engines are based on the motor cycle of combustion Otto, who requires a natural gas with well definite specification, conferring characteristic anti-detonating necessary to the equipment performance for projects based on this cycle. In this work, process routes and thermodynamic conditions had been selected and evaluated. Based on simulation assays carried out in commercial simulators the content of the methane index of the effluent gas were evaluated at various ranges of pressure, temperature, flowrate, molecular weight and chemical nature and composition of the absorbent. As final result, it was established a route based on process efficiency, optimized consumption of energy and absorbent. Thereby, it serves as base for the compact equipment conception to be used in locu into the industry for the removal of hydrocarbon from the natural gas produced

FLOW PROPERTIES and TUBE FRICTION FACTOR of MILK CREAM: INFLUENCE of TEMPERATURE and FAT CONTENT

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Laminar flow of soursop juice through concentric annuli: Friction factors and rheology

Laminar axial flow of a pseudoplastic fluid food (soursop, juice) in annular ducts has been experimentally investigated. In the first part of the manuscript, the rheological behavior of soursop juice, being essential for the annular flow analysis, was completely determined from 9.3 to 49.4 degrees Brix and temperatures from 0.4 degrees C to 68.8 degrees C, using a rotational rheometer equipped with coaxial cylinders. In order to test the adequacy of the rheology results, pressure loss data in the laminar pipe flow were collected and then experimental and theoretical friction factors were compared, showing excellent agreement, which indicated the reliability of the Power-Law model for describing the soursop juices. In the second part, pressure loss in annular regions was measured and used to estimate friction factors, which were then compared to those resulted from analytical and semi-analytical equations. The principal contributions of this article are to provide a review on the determination of friction factors-Reynolds number of pseudoplastic fluids in annuli, and also supply extensive new experimental data on the rheological properties and pressure loss of an important shear-thinning fluid food, which is of particular interest for the food engineering process design. (c) 2006 Elsevier Ltd. All rights reserved.

Towards a strategic CSR: A Brazilian case study

Purpose - Organisations may be considered, at the same time, either part of the problem or part of the solution for the social-environmental crisis that is occurring. To be part of the solution, they must head for a strategic management of corporate social responsibility (CSR). The objective of the present study is to identify and analyse the interfaces between theoretical models of strategic implementation of CSR and the variables and major players involved in this process. Design/methodology/approach - This is a qualitative research using a case study strategy. The company chosen for this case study has been highlighted as one of the best national companies to work for, with significant social responsibility indices. Findings - The case study found some results, such as the importance of aligning with human resource management for strategic implementation of CSR and the integrative characteristic between different workers, that are essential for this process. Originality/value - Only a few international articles discuss CSR in Brazil. The results could be useful for classes focusing on Doing business in Brazil. © Emerald Group Publishing Limited.

Development and validation of a microbiological assay for determination of chlorhexidine digluconate in aqueous solution

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Comparison of different designs of implant-retained overdentures and fixed full-arch implant-supported prosthesis on stress distribution in edentulous mandible - A computed tomography-based three-dimensional finite element analysis

A finite element analysis was used to compare the effect of different designs of implant-retained overdentures and fixed full-arch implant-supported prosthesis on stress distribution in edentulous mandible. Four models of an human mandible were constructed. In the OR (O'ring) group, the mandible was restored with an overdenture retained by four unsplinted implants with O'ring attachment; in the BC (bar-clip) -C and BC groups, the mandibles were restored with overdentures retained by four splinted implants with bar-clip anchor associated or not with two distally placed cantilevers, respectively; in the FD (fixed denture) group, the mandible was restored with a fixed full-arch four-implant-supported prosthesis. Models were supported by the masticatory muscles and temporomandibular joints. A 100-N oblique load was applied on the left first molar. Von Mises (σvM), maximum (σmax) and minimum (σmin) principal stresses (in MPa) analyses were obtained. BC-C group exhibited the highest stress values (σvM=398.8, σmax=580.5 and σmin=-455.2) while FD group showed the lowest one (σvM=128.9, σmax=185.9 and σmin=-172.1). Within overdenture groups, the use of unsplinted implants reduced the stress level in the implant/prosthetic components (59.4% for σvM, 66.2% for σmax and 57.7% for σmin versus BC-C group) and supporting tissues (maximum stress reduction of 72% and 79.5% for σmax, and 15.7% and 85.7% for σmin on the cortical and trabecular bones, respectively). Cortical bone exhibited greater stress concentration than the trabecular bone for all groups. The use of fixed implant dentures and removable dentures retained by unsplinted implants to rehabilitate edentulous mandible reduced the stresses in the periimplant bone tissue, mucosa and implant/prosthetic components. © 2013 Elsevier Ltd.

Critical factors to be considered when planning the implementation of environmental improvements and energy saving

To identify the critical success factors in the adoption of energy efficiency actions in Brazilian hospitals and describe their behaviour are the objectives of this paper. In order to achieve these goals, a literature review was performed on green management and energy efficiency. This was the basis to define the questions of the interview script applied to two hospitals located in the state of Sao Paulo, Brazil. The interview script application was complemented by secondary data and direct observation. The results showed that: a) the studied hospitals are embracing environmental management actions more often and, whenever possible, energy efficiency actions are taken as well; and b) in the cases analysed top management support, commitment with the environment, green process design and employee empowerment were some of the most relevant critical success factors to the accomplishment of energy efficiency actions. These findings may be of interest to emerging countries, including BRICS (Brazil, Russia, India, China and South Africa).