Application of a SPH depth-integrated model to landslide run-out analysis

Hazard and risk assessment of landslides with potentially long run-out is becoming more and more important. Numerical tools exploiting different constitutive models, initial data and numerical solution techniques are important for making the expert’s assessment more objective, even though they cannot substitute for the expert’s understanding of the site-specific conditions and the involved processes. This paper presents a depth-integrated model accounting for pore water pressure dissipation and applications both to real events and problems for which analytical solutions exist. The main ingredients are: (i) The mathematical model, which includes pore pressure dissipation as an additional equation. This makes possible to model flowslide problems with a high mobility at the beginning, the landslide mass coming to rest once pore water pressures dissipate. (ii) The rheological models describing basal friction: Bingham, frictional, Voellmy and cohesive-frictional viscous models. (iii) We have implemented simple erosion laws, providing a comparison between the approaches of Egashira, Hungr and Blanc. (iv) We propose a Lagrangian SPH model to discretize the equations, including pore water pressure information associated to the moving SPH nodes

Sediment temperatures of the Håkon Mosby mud volcano measured continuously with a short temperature lance (LOOME)

The short sediment temperature probe were deployed and recovered with the LOOME observatory in 2009 and 2010, respectively. In addition to temperature, the loggers also recorded bottom water pressure at a sampling interval of 20 minutes. Even though the data obtained from the short temperature probe was strongly disturbed by leakage through a corroded connector, the data shows clearly that the probe was pulled out of the sediment on October 26, 2009, presumably by advancing mud flows.

Description of recent sediments of Nile Delta, Red Sea and Gulf of Aden (Table 1-3)

The study of textural, structural, chemical, and physical properties of fine-grained recent marine sediments leads to the conclusion that only a few compositional factors are responsible for significant changes in mass physical characteristics in the upper meters below sea bottom. Fossil-induced porosity increases water content and liquid limit. It also seems to have partially influenced the plastic limit and plasticity index of calcareous sandy silts from the Red Sea and the western Gulf of Aden so that they become similar to the montmorillonite rich prodelta clays from the Nile Delta. Diagrams based on liquid limit and plasticity loose their original meaning in these cases. Activity of sediments rich in microorganisms can be higher than that of montmorillonitic clay. The shear strength-depth relationship of normally consolidated sediments is surprisingly little influenced by changes in sand or clay content and clay mineralogy. Only high lime content, submarine erosion and beginning cementation increase the strength considerably. Erosional disconformities near the present surface can be deduced from the strength-depth curve when as little as 1 or 2 m sediment have been removed. Flat or irregular strength-depth curves indicate beginning cementation and probably discontinuous sedimentation, provided the composition of the material remains in some degree constant. In our samples diagenetic pyrite, but no recristallisation of carbonates could be detected under the microscope. Underconsolidation and excess pore-water pressure, factors which tend to foster submarine slides, mud lumps, and diapiric folding, seem to be restricted Varito areas with mainly rapidly deposited, homogeneous or layered sediments. But where an abundance of burrowing organisms increases the vertical permeability of the sediment, normal consolidation and stable deposits are to be expected, at least in the upper meters below the present surface. According to 14C-determinations on calcareous microorganisms the rate of deposition of the investigated sediments seems to range from 26 to 167 cm per 1000 years.

Oceans Deep: Lesson D (Mysteries of the Deep)

Teacher resources for Lesson D in the Discover Oceanography 'Scheme of Work' for use in schools.

Consolidation of Loess, 1971

Effective stress paths for a loessial soil subject to collapse during confined compression have been determined from the results of a testing program consisting of (1) confined compression tests on natural samples of loess with initial water contents ranging from air-dry to saturation, (2) negative pore-water pressure measurements to -300 psi during these tests, and (3) Ko-tests in which the lateral stress ratio was measured for one-dimensional strain. Before collapse, Ko was found to average 0.23, an extremely low value for a loose soil, whereas after collapse, Ko increased to 0.54, which is consistent with values for other soils. Because of the low Ko-values before collapse, the effective stress path for loading in confined compression initially approaches the failure envelope. At collapse the stress path intersects the failure envelope and thereafter it changes direction as a consequence of the higher Ko-value after collapse. From the stress path interpretation of the results, it is demonstrated that the collapse mechanism of loess in confined compression and during wetting is a shear phenomenon and subject of analysis in terms of effective stresses.

Stability of Granular Base Course Materials Containing Bituminous Admixtures

This report concerns the stabilization of three crushed limestones by an ss-1 asphalt emulsion and an asphalt cement, 120-150 penetration. Stabilization is evaluated by marshall stability and triaxial shear tests. Test specimens were compacted by the marshall, standard proctor and vibratory methods. Stabilization is evaluated primarily by triaxial shear tests in which confining pressures of 0 to 80 psi were used. Data were obtained on the angle of internal friction, cohesion, volume change, pore water pressure and strain characteristics of the treated and untreated aggregates. The MOHR envelope, bureau of reclamation and modified stress path methods were used to determine shear strength parameters at failure. Several significant conclusions developed by the authors are as follows: (1) the values for effective angle of internal friction and effective cohesion were substantially independent of asphalt content, (2) straight line MOHR envelopes of failure were observed for all treated stones, (3) bituminous admixtures did little to improve volume change (deformation due to load) characteristics of the three crushed limestones, (4) with respect to pore water characteristics (pore pressures and suctions due to lateral loading), bituminous treatment notably improved only the bedford stone, and (5) at low lateral pressures bituminous treatments increased stability by limiting axial strain. This would reduce rutting of highway bases. At high lateral pressures treated stone was less stable than untreated stone.

Evaluation of One-Dimensional Seismic Site Response Analyses at Small to Large Strain Levels

Thesis (Master's)--University of Washington, 2016-08

Designing for User-facing Uncertainty in Everyday Sensing and Prediction

Thesis (Ph.D.)--University of Washington, 2016-07

A Study on the liquefaction risk in seismic design of foundations

A fully coupled non-linear effective stress response finite difference (FD) model is built to survey the counter-intuitive recent findings on the reliance of pore water pressure ratio on foundation contact pressure. Two alternative design scenarios for a benchmark problem are explored and contrasted in the light of construction emission rates using the EFFC-DFI methodology. A strain-hardening effective stress plasticity model is adopted to simulate the dynamic loading. A combination of input motions, contact pressure, initial vertical total pressure and distance to foundation centreline are employed, as model variables, to further investigate the control of permanent and variable actions on the residual pore pressure ratio. The model is verified against the Ghosh and Madabhushi high acceleration field test database. The outputs of this work is aimed to improve the current computer-aided seismic foundation design that relies on ground’s packing state and consistency. The results confirm that on seismic excitation of shallow foundations, the likelihood of effective stress loss is greater in deeper depths and across free field. For the benchmark problem, adopting a shallow foundation system instead of piled foundation benefitted in a 75% less emission rate, a marked proportion of which is owed to reduced materials and haulage carbon cost.

Micromechanical insight into the undrained instability of granular materials: deformation characteristics of geomaterials.

There is no agreement between experimental researchers whether the point where a granular material responds with a large change of stresses, strains or excess pore water pressure given a prescribed small input of some of the same variables defines a straight line or a curve in the stress space. This line, known as the instability line, may also vary in shape and position if the onset of instability is measured from drained or undrained triaxial tests. Failure of granular materials, which might be preceded by the onset of instability, is a subject that the geotechnical engineers have to deal with in the daily practice, and generally speaking it is associated to different phenomena observed not only in laboratory tests but also in the field. Examples of this are the liquefaction of loose sands subjected to undrained loading conditions and the diffuse instability under drained loading conditions. This research presents results of DEM simulations of undrained triaxial tests with the aim of studying the influence of stress history and relative density on the onset of instability in granular materials. Micro-mechanical analysis including the evolution of coordination numbers and fabric tensors is performed aiming to gain further insight on the particle-scale interactions that underlie the occurrence of this instability. In addition to provide a greater understanding, the results presented here may be useful as input for macro-scale constitutive models that enable the prediction of the onset of instability in boundary value problems.

A methodological approach for the performance optimization of transient seepage models through inverse analysis

The topic of the Ph.D project focuses on the modelling of the soil-water dynamics inside an instrumented embankment section along Secchia River (Cavezzo (MO)) in the period from 2017 to 2018 and the quantification of the performance of the direct and indirect simulations . The commercial code Hydrus2D by Pc-Progress has been chosen to run the direct simulations. Different soil-hydraulic models have been adopted and compared. The parameters of the different hydraulic models are calibrated using a local optimization method based on the Levenberg - Marquardt algorithm implemented in the Hydrus package. The calibration program is carried out using different types of dataset of observation points, different weighting distributions, different combinations of optimized parameters and different initial sets of parameters. The final goal is an in-depth study of the potentialities and limits of the inverse analysis when applied to a complex geotechnical problem as the case study. The second part of the research focuses on the effects of plant roots and soil-vegetation-atmosphere interaction on the spatial and temporal distribution of pore water pressure in soil. The investigated soil belongs to the West Charlestown Bypass embankment, Newcastle, Australia, that showed in the past years shallow instabilities and the use of long stem planting is intended to stabilize the slope. The chosen plant species is the Malaleuca Styphelioides, native of eastern Australia. The research activity included the design and realization of a specific large scale apparatus for laboratory experiments. Local suction measurements at certain intervals of depth and radial distances from the root bulb are recorded within the vegetated soil mass under controlled boundary conditions. The experiments are then reproduced numerically using the commercial code Hydrus 2D. Laboratory data are used to calibrate the RWU parameters and the parameters of the hydraulic model.

ANALYSIS OF PRESSURE FLUCTUATIONS DURING WATER EVAPORATION IN SPOUTED BED

The aim of this work was to study the behaviour of conventional spouted beds during water evaporation and to analyze the pressure fluctuations at the maximum water evaporative capacity for different bed heights and air flow rates. The results showed that spout pressure drop could not indicate the proximity of maximum evaporative capacity; however this condition is denoted by a minimum in fountain height. The standard deviation and amplitude of the pressure fluctuations also showed a minimum point at the maximum water evaporation capacity. The frequency domain analysis of pressure fluctuations revealed that the dry bed has a dominant frequency varying from 6 to 8.2 Hz and that the peak of dominant frequency tends to disappear with the increase in water feed rate.