Stability control of a railway vehicle using absolute stiffness and inerters

Work presented in this paper studies the potential of employing inerters -a novel mechanical device used successfully in racing cars- in active suspension configurations with the aim to enhance railway vehicle system performance. The particular element of research in this paper concerns railway wheelset lateral stability control. Controlled torques are applied to the wheelsets using the concept of absolute stiffness. The effects of a reduced set of arbitrary passive structures using springs, dampers and inerters integrated to the active solution are discussed. A multi-objective optimisation problem is defined for tuning the parameters of the proposed configurations. Finally, time domain simulations are assessed for the railway vehicle while negotiating a curved track. A simplification of the design problem for stability is attained with the integration of inerters to the active solutions. © 2012 IEEE.

Characterization of the surface acoustic wave devices based on ZnO/nanocrystalline diamond structures

Nanocrystalline ZnO films with strong (0002) texture and fine grains were deposited onto ultra-nanocrystalline diamond (UNCD) layers on silicon using high target utilization sputtering technology. The unique characteristic of this sputtering technique allows room temperature growth of smooth ZnO films with a low roughness and low stress at high growth rates. Surface acoustic wave (SAW) devices were fabricated on ZnO/UNCD structure and exhibited good transmission signals with a low insertion loss and a strong side-lobe suppression for the Rayleigh mode SAW. Based on the optimization of the layered structure of the SAW device, a good performance with a coupling coefficient of 5.2% has been realized, promising for improving the microfluidic efficiency in droplet transportation comparing with that of the ZnO/Si SAW device. An optimized temperature coefficient of frequency of -23.4 ppm°C-1 was obtained for the SAW devices with the 2.72 μm-thick ZnO and 1.1 μm-thick UNCD film. Significant thermal effect due to the acoustic heating has been redcued which is related to the temperature stability of the ZnO/UNCD SAW device. © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Electronic structures of GaAs/AlAs lateral superlattices

The electronic energy subbands and minigaps in lateral superlattices (LSLs) have been calculated by the plane-wave expansion method. The effect of the lateral modulation on the critical well width at which an indirect-direct (X-Gamma) optical transition occurs in the LSLs is investigated. Our theoretical results are in agreement with the available experimental data. Totally at variance with the previous variation calculational results, the minigaps between the first two subbands in LSLs, as functions of the modulation period, exhibit a maximum value at a specific length and disappear on decreasing the modulation period further. The modulations of several types of lateral potential are also evaluated; the indication is that the out-of-phase modulation on either side of the wells is the strongest while the in-phase modulation is the weakest. Our calculations also show that the effect of the difference between the effective masses of the electrons in the different materials on the subband structures is significant.

Photoluminescence study of InxGa1-xAs/InyAl1-yAs one-side-modulation-doped asymmetric step quantum wells

Fourier transform photoluminescence measurements were carried out to investigate the optical transitions in InxGa1-xAs/InyAl1-yAs one-side-modulation-doped asymmetric step quantum wells. Samples with electron density n(s) between 0.8 and 5.3 x 10(12) cm(-2) rue studied. Strong recombination involving one to three populated electron subbands with the first heavy-hole subband is observed. Fermi edge singularity (FES) clearly can be observed for some samples. The electron subband energies in the InGaAs/InAlAs step quantum wells were calculated by a self-consistent method, taking into account strain and nonparabolicity effects and the comparison with the experimental data shows a good agreement. Our results can help improve understanding for the application of InGaAs/InAlAs step quantum wells in microelectronic and optoelectronic devices. (C) 1998 Elsevier Science Ltd. All rights reserved.

DENSITY-OF-STATES OF THE 2-DIMENSIONAL ELECTRON-GAS STUDIED BY MAGNETOCAPACITANCES OF BIASED DOUBLE-BARRIER STRUCTURES

The magnetocapacitive response of a double-barrier structure (DBS), biased beyond resonances, has been employed to determine the density of states (DOS) of the two-dimensional electron gas residing in the accumulation layer on the incident side of the DBS. An adequate procedure is developed to compare the model calculation of the magnetocapacitance with the experimental C vs B curves measured at different temperatures and biases. The results show that the fitting is not only self-consistent but also remarkably good even in well-defined quantum Hall regimes. As a result, information about the DOS in strong magnetic fields could reliably be extracted.

Poly(oligothiophene-alt-benzothiadiazole)s: Tuning the Structures of Oligothlophene Units toward High-Mobility "Black" Conjugated Polymers

A series of donor-acceptor low-bandgap conjugated polymers, i.e., PTnBT (n = 2-6), composed of alternating oligothiophene (OTh) and 2,1,3-benzothiadiazole (BT) units were synthesized by Stille cross-coupling polymerization. The number of thiophene rings in OTh units, that is n, was tuned from 2 to 6. All these polymers display two absorption bands in both solutions and films with absorption maxima depending on n. From solution to film, absorption spectra of the polymers exhibit a noticeable red shift. Both high- and low-energy absorption bands or P'F5BT and PT6BT films locate in the visible region, which are at 468 and 662 nm for PT5BT and 494 and 657 nm for PT6BT.

Organolanthanides with 3-(2-pyridylmethyl) indenyl ligands: synthesis, crystal structures and catalytic activities of divalent complexes for epsilon-caprolactone polymerization

Reaction of 3-(2-pyridylmethyl)indenyl lithium (1) with LnI(2)(THF)(2) (Ln = Sm, Yb) in THF produced the divalent organolanthanides (C5H4NCH2C9H6)(2)Ln(II)(THF) (Ln = Sm (2), Yb (3)) in high yield. 1 reacts with LnCl(3) (Ln = Nd, Sm, Yb) in THF to give bis(3-(2-pyridylmethyl)indenyl) lanthanide chlorides (C5H4NCH2C9H6)(2)Ln(III)Cl (Ln = Nd (4), Sm (5)) and the unexpected divalent lanthanides 3 (Ln = Yb). Complexes 2-5 show more stable in air than the non-functionalized analogues. X-ray structural analyses of 2-4 were performed. 2 and 3 belong to the high symmetrical space group (Cmcm) with the same structures, they are THF-solvated 9-coordinate monomeric in the solid state, while 4 is an unsolvated 9-coordinate monomer with a trans arrangement of both the side-arms and indenyl rings in the solid state. Additionally, 2 and 3 show moderate polymerization activities for F-caprolactone (CL).

Synthesis and characterization of novel polythiophenes containing poly(ethylene oxide) side chains

Thiophene copolymers and their derivatives with poly(ethylene oxide) side chains were synthesized. The starting monomers were 3-hexylthiophene and 2-(3-thienyl) ethanol with poly(ethylene oxide) grafted to the side chains. New functionalized polythiophenes were prepared by both chemical oxidation with FeCl3 and electropolymerization. The conjugating polymers were characterized. The structures of the polythiophene derivatives agreed with the design.

Syntheses and crystal structures of bis(tetrahydrofurfurylindenyl) lanthanocene chlorides (C4H7OCH2C9H6)(2)LnCl (Ln = Nd, Sm, Dy, Ho, Er, Yb)

Reaction of anhydrous lanthanide trichlorides with tetrahydrofurfuryl indenyl lithium in THF afforded bis(tetrahydrofurfurylindenyl) lanthanocene chlorides complexes (C4H7OCH2C9H6)(2) LnCl, Ln = Nd (1), Sm (2), Dy (3), Ho (4), Er (5), Yb (6). The X-ray crystallographic structures of all the six complexes were determined and these indicate that they are unsolvated nine-coordinate monomeric complexes with a trans arrangement of both the sidearm and indenyl rings in the solid state. They belong to the same crystal system (orthorhombic) and space group (P2(1)2(1)2(1)) with the same structure. Especially, they are more stable to air and moisture than the corresponding unsubstituted indenyl lanthanide complexes.

Synthesis and characterization of chiral smectic side-chain liquid crystalline polysiloxanes and ionomers containing sulfonic acid groups

The synthesis of new chiral smectic A (S-A) side-chain liquid crystalline polysiloxanes (LCPs) and ionomers (LCIs) containing 4-allyloxy-benzoyl-4-(S-2-ethylhexanoyl) p-benzenediol his ate (ABB) as mesogenic units and 4-[[4-(2-propenyloxy)phenyl] azo]benzensulfonic acid (AABS) as nonmesogenic units is presented. The chemical structures of the monomers and polymers are confirmed by FTIR spectroscopy or H-1-NMR. Differential scanning calorimetry (DSC), optical polarizing microscopy, and X-ray diffraction measurements reveal that all the polymers P-I-P-IV and ionomers P-V-P-VI exhibit S-A texture. The results seem to demonstrate that the tendency toward the S-A-phase region increases with increasing sulfonic acid concentration, and the thermal stability of the S-A phase is determined by the flexibility of the polymer backbones and the interactions of sulfonic acid groups. (C) 2001 John Wiley & Sons, Inc.

The effects of different alkyl substitution on the structures and properties of poly(3-alkylthiophenes)

In order to investigate the influence of different alkyl side chain substitution on the structures and properties of P3ATs, X-ray diffraction, differential scanning calorimetry (DSC), thermal gravity analysis (TGA), Fourier transform infrared spectra (FTIR) and ultraviolet-visible spectra (W-VIS) were applied to characterizing the samples of ploy(3-octylthiophene) (P3OT), poly(3-dodecylthiophene) (P3DDT) and poly(3-octadecylthiophene) (P3ODT). It is found that the different length of alkyl group substitution leads to great difference in molecular chain packings, according to the room temperature X-ray diffraction results. The temperature dependence of X-ray diffraction experiments were also performed to study the melting processes of P3ATs. With the increase in the number of carbon atoms in alkyl side chains, the melting point decreases, and the thermal stability decreases too. The results of both FTIR and W-VIS spectra indicate that the conjugation length of P3DDT is the longest. among the three P3ATs. (C) 2001 Elsevier Science B.V. All rights reserved.

Syntheses and reactions of heterometallic complexes of nickel and copper with tetrathiotungstates. The molecular structures of [Ph(4)P](2)[S2W(mu-S)(2)Ni(S-2)] and W(mu-S)(4)Cu-2(PPh(3))(4)center dot py

Reaction of [Ph(4)P]2WS4 With NiCl2 in methanol solution in the presence of NaOCH3 leads to the formation of [Ph(4)P](2) [S2W(mu-S)(2)Ni(S-2)] (I) A Similar reaction between (NH4)(2)WS4 and NiCl2 under O-2 atmosphere in the presence of Ph(4)PCl or (n)Bu(4)NCl affords [Ph(4)P](2)([(S-2)W(O)(mu-S)(2)]Ni-2] (IIa) and [(n)Bu(4)N](2)([(S-2)W(O)(mu-S)(2)]Ni-2} (IIb) Under argon the same reaction gives [Ph(4)P](2)[Ni(WS4)(2)] (IIIa) and [(n)Bu(4)N](2)[Ni(WS4)(2)] (IIIb). [Ph(4)P](2)[Ni(WOS3)(2)] (IV) and [Ph(4)P](2)[Ni(WO2S2)(2)] (V) can be prepared from the reaction of [Ph(4)P]2WOS3 and [Ph(4)P]2WO2S2 with NiCl2. Treatment of (NH4)(2)WS4 with CuCl in the presence of PPh(3) in boiling pyridine produces W(mu-S)(4)Cu-2(PPh(3))(3) (VI), which can further react with excess PPh(3) to give W(mu-S)(4)Cu-2(PPh(3))(4) . py (VII). Complex I crystallizes in the space group P2(1)/n with the cell parameters: a = 20.049(4), b = 17.010(4), c = 14.311(7) Angstrom; beta = 110.24(3)degrees and Z = 4; R = 0.058 for 4267 independent reflections. The structural study confirms that complex I contains two terminal sulfide ligands, two bridging sulfide ligands, a side-on disulfide ligand, and a planar central W(mu-S)(2)Ni four membered ring. Complex VII crystallizes in the space group C2/c with the cell parameters: a = 26.436(8), b = 20.542(6), c = 19.095(8) Angstrom; beta = 125.00(3)degrees and Z = 4; R = 0.080 for 3802 independent reflections. The structural study reveals a perfect linear arrangement of the three metal atoms Cu-W-Cu.

Vascular structures for volumetric cooling and mechanical strength

When solid material is removed in order to create flow channels in a load carrying structure, the strength of the structure decreases. On the other hand, a structure with channels is lighter and easier to transport as part of a vehicle. Here, we show that this trade off can be used for benefit, to design a vascular mechanical structure. When the total amount of solid is fixed and the sizes, shapes, and positions of the channels can vary, it is possible to morph the flow architecture such that it endows the mechanical structure with maximum strength. The result is a multifunctional structure that offers not only mechanical strength but also new capabilities necessary for volumetric functionalities such as self-healing and self-cooling. We illustrate the generation of such designs for strength and fluid flow for several classes of vasculatures: parallel channels, trees with one, two, and three bifurcation levels. The flow regime in every channel is laminar and fully developed. In each case, we found that it is possible to select not only the channel dimensions but also their positions such that the entire structure offers more strength and less flow resistance when the total volume (or weight) and the total channel volume are fixed. We show that the minimized peak stress is smaller when the channel volume (φ) is smaller and the vasculature is more complex, i.e., with more levels of bifurcation. Diminishing returns are reached in both directions, decreasing φ and increasing complexity. For example, when φ=0.02 the minimized peak stress of a design with one bifurcation level is only 0.2% greater than the peak stress in the optimized vascular design with two levels of bifurcation. © 2010 American Institute of Physics.

Structures of P-glycoprotein reveal its conformational flexibility and an epitope on the nucleotide-binding domain

P-glycoprotein (P-gp) is one of the best-known mediators of drug efflux-based multidrug resistance in many cancers. This validated therapeutic target is a prototypic, plasma membrane resident ATPBinding Cassette transporter that pumps xenobiotic compounds out of cells. The large, polyspecific drug-binding pocket of P-gp recognizes a variety of structurally unrelated compounds. The transport of these drugs across the membrane is coincident with changes in the size and shape of this pocket during the course of the transport cycle. Here, we present the crystal structures of three inward-facing conformations of mouse P-gp derived from two different crystal forms. One structure has a nanobody bound to the C-terminal side of the first nucleotide-binding domain. This nanobody strongly inhibits the ATP hydrolysis activity of mouse Pgp by hindering the formation of a dimeric complex between the ATP-binding domains, which is essential for nucleotide hydrolysis. Together, these inward-facing conformational snapshots of P-gp demonstrate a range of flexibility exhibited by this transporter, which is likely an essential feature for the binding and transport of large, diverse substrates. The nanobody-bound structure also reveals a unique epitope on P-gp.

Experimental investigation of thermal structures in regular three-dimensional falling films

Interfacial waves on the surface of a falling liquid film are known to modify heat and mass transfer. Under non-isothermal conditions, the wave topology is strongly influenced by the presence of thermocapillary (Marangoni) forces at the interface which leads to a destabilization of the film flow and potentially to critical film thinning. In this context, the present study investigates the evolution of the surface topology and the evolution of the surface temperature for the case of regularly excited solitary-type waves on a falling liquid film under the influence of a wall-side heat flux. Combining film thickness (chromatic confocal imaging) and surface temperature information (infrared thermography), interactions between hydrodynamics and thermocapillary forces are revealed. These include the formation of rivulets, film thinning and wave number doubling in spanwise direction. Distinct thermal structures on the films’ surface can be associated to characteristics of the surface topology.