Influence of blood viscosity to cerebral blood flow in older humans compared to young subjects

Objective: Since blood viscosity (BV) is one of the most important factors determining blood flow, this study aimed to investigate the possible correlation between increased blood viscosity and reduction of regional cerebral blood flow (rCBF) in healthy ageing.Methods: Male subjects were distributed in two groups: "young", aged 20-30 (27 volunteers), or "elderly", aged 60-70 (50 volunteers). Whole blood viscosity was obtained with a Wells-Brookfield Cone/Plate Viscometer. Cerebral blood flow was analysed by means of single photon emission computed tomography (SPECT).Results: The mean BV values were 3.28 +/- 0.43 mPa in the group of young volunteers and 4.33 +/- 0.73 mPa in the group of elderly volunteers (t = -6.9, p < 0.0001). The elderly had a lower blood flow than the young in the following regions: bilateral parietal; temporal-parietal and temporal of the left hemisphere. Pearson's correlation between BV and rCBF showed a good inverse correlation when the BV was above 3.95 +/- 0.83 mPa.Conclusions: Our results point to a close relationship between the two parameters analysed, BV and rCBF. The impairment in rCBF observed in the elderly volunteers might be due to an increase in BV, among other factors.Significance: These findings suggest interesting possibilities for the treatment/prevention of brain ageing. (C) 2011 International Federation of Clinical Neurophysiology. Published by Elsevier B.V. All rights reserved.

PRODUCTION of THERMAL PHOTONS IN VISCOUS FLUID DYNAMICS WITH TEMPERATURE-DEPENDENT SHEAR VISCOSITY

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Shear viscosity from thermal fluctuations in relativistic conformal fluid dynamics

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Influence of viscosity and ionic concentration on morphology of PLZT thin films

PLZT thin films were prepared by a dip-coating process using Pechini's method. The PLZT solution was obtained from the mixture of the cation solutions. The viscosity of the solution was adjusted in the range of 20-40 cP, while the ionic concentration was adjusted in the range of 0.1 and 0.2 M. PLZT solutions were deposited on Si (1 0 0) substrate with withdrawal speed at 5 mm/min. The coated substrates were thermally treated with heating rate of 1 degreesC/min up to 300 and 5 degreesC/ min up to 650 degreesC in order to obtain homogeneous and crack free films. The influence of viscosity and ionic concentration on crystallization and morphology of PLZT (9/65/35) thin film will be discussed. (C) 2001 Elsevier B.V. B.V. All rights reserved.

A viscosity model for fluorochloroindate glasses

Viscosity of fluoride glasses is generally Arrhenian between glass transition temperature and crystallization temperature. This dependence on temperature is not observed in some special compositions which have two regions with different activation energies. The viscosity of glasses 40InF(3)-20ZnF(2)-25BaF(2)-10SrF(2)-5LiCl and 40InF(3)-20ZnF(2)-15SrF(2)-20BaF(2)-5NaCl was obtained by the parallel plate method. A theoretical model has been proposed to explain the viscosity data. (C) 1999 Elsevier B.V. B.V. All rights reserved.

Dynamic viscosity of binary and ternary mixtures containing poly(ethylene glycol), potassium phosphate, and water

Dynamic viscosity of binary mixtures of poly(ethylene glycol) molar mass 1500 da + water, potassium phosphate + water, and ternary mixtures of poly(ethylene glycol) molar mass 1500 da + potassium phosphate + water were determined at 303.15 K Binary and ternary mixture viscosities showed a direct logarithm-type relation with the increase of poly(ethylene glycol) and potassium phosphate contents. The models used for viscosity correlation gave a good fit to the experimental data.

Influence of the concentration of Sb2O3 and the viscosity of the precursor solution on the electrical and optical properties of SnO2 thin films produced by the Pechini method

SnO2:Sb multi-layer coatings were prepared by the Pechini method. An investigation was made of the influence of the concentration of Sb2O3 and the viscosity of the precursor solution on the electrical and optical properties of SnO2 thin films. The use of a multi-layer system as an alternative form of increasing the packing and. thus. decreasing porosity proved to be efficient, decreasing the system's resistivity without altering its optical properties. (C) 2002 Elsevier B.V. B.V. All rights reserved.

Structure of a glycoglucuronomannan from the low-viscosity gum of Vochysia lehmannii

The polysaccharide (VSP) from the gum exudate of quaruba (Vochysia lehmannii) had two components of almost identical M. centred at 24,800, as shown by HSPEC-MALLS. The presence of aggregates was shown since carboxy-reduction gave VSP-RED, which contained low molecular weight components with M-w 19,000 > 5800 and polydispersity ratios dn/dc 0.160 and 0.149, respectively. VSP formed low viscosity aqueous solutions and acid hydrolysis gave Man (30%), Ara (16%), Gal (10%), and Glc (14%). The latter arose partly from GlcA (30%). Methylation analysis revealed mainly neutral units of 2-O- (60%) and 2,3-di-O-substituted Manp (5%), and those of nomeducing ends (8%), 2-O- (3%), and 4-O-substituted Arap and/or 5-O-substituted Araf units (6%). VSP-RED contained Glc (45%), Man (35%), and Ara (13%) and methylation analysis indicated mainly 4-O-substituted Glcp (31%) and 2-O- (51%) and 2,3-di-O-substituted Manp units (5%). A predominant alternating structure for VSP was shown by its C-13 NMR spectrum, which contained 10 main signals and a small one of C-6 of GlcpA. This was confirmed by formation, on partial hydrolysis of VSP, of a tetrasaccharide, which was characterised by NMR spectroscopy and ESI-MS as beta-GlcpA-(1 --> 2)-alpha-Manp-(1 --> 4)-beta-GlcpA-(1 --> 2)-Man, which arose from the main chain, thus confirming VSP to be a glycoglucuronomannan. (C) 2004 Elsevier Ltd. All rights reserved.

Effect of apparent viscosity on fluidized bed drying process parameters of guava pulp

Pressure drop and minimum fluidization velocity were experimentally studied in a vibro-fluidized bed of inert particles subjected to different vibration intensities during drying of guava pulp. Maltodextrin was added to the pulp in order to prevent stickiness between particles and the consequent bed collapse. Pulps were initially concentrated, resulting in pastes with different soluble solids content, and a constant fraction of maltodextrin was guaranteed in the final pulp samples. The pulp rheological behavior as affected by temperature and total soluble solids content, including maltodextrin, was evaluated and the effect of pulp apparent viscosity on pressure drop and minimum vibro-fluidization velocity were investigated. Two types of inert particles -3.6 mm glass beads and 3 mm Teflon cylinders were tested and, due to lower pressure drop presented by Teflon cylinders during operation of the dry vibro-fluidized bed, these particles were adopted for pulp drying process. Increasing pulp apparent viscosity caused a considerable increase in the vibro-fluidized bed pressure drop during pulp drying and, as a consequence resulted in a larger value of minimum vibro-fluidization velocity. on the other hand, the negative effect of increasing apparent viscosity could be attenuated by increasing the fluidized bed vibration intensity, which could prevent stickiness between particles. (c) 2006 Elsevier Ltd. All rights reserved.

Dielectric thermal analysis as a tool for quantitative-evaluation of the viscosity and the kinetics of epoxy resin cure

Dielectric thermal analysis has been proved as a valuable tool for monitoring the epoxy curing process and the related rheological properties in the fabrication of polymer-matrix composite materials. This technique also has the potential to be applied in the monitoring of magnet impregnation processes as well as in quality control. In this work we present the quantitative evaluation of the viscosity changing and the curing kinetics for a commercial Stycast epoxy resin system at different temperatures through the impedance analysis. The results showed correlation between the real component of the complex impedance and the isothermal reaction extent. Comparing the dielectric analysis result with the viscosity measured by rotational rheometer we observed a similar behavior reported for dynamic mechanic analysis. The results comparison have shown that the kinetics parameters obtained from DSC and DETA analysis showed different sensitivities related to the characteristics of curing stages. We concluded that the dielectric thermal analysis should be applied in quantitative evaluation of cure kinetics.

Viscosity of aqueous carbohydrate solutions at different temperatures and concentrations

Experimental viscosity values of sucrose, glucose, and fructose aqueous solutions in a large range of temperatures (0 to 85 degrees C) and concentrations (10 to 60% w/w) that might be encountered in food processes were obtained in order to contribute to extending the available database of food properties. The temperature dependence of viscosity could be adequately described by the Arrhenius model, and the activation energy was well represented by a unique function of the solute volume fraction, valid for sucrose, glucose, and fructose solutions.

Effect of apparent viscosity on the pressure drop during fluidized bed drying of soursop pulp

Pressure drop and minimum fluidization velocity were experimentally studied in a vibro-fluidized bed of inert particles subjected to different vibration intensities during drying of soursop pulp. Maltodextrin was added to the pulp in order to prevent stickiness between particles and the consequent bed collapse. Pulps were initially concentrated, resulting in pastes with different soluble solids content, and a constant fraction of maltodextrin was guaranteed in the final pulp samples. The pulp theological behavior as affected by temperature and total soluble solids content, including maltodextrin, was evaluated and the effect of pulp apparent viscosity on pressure drop and minimum vibro-fluidization velocity were investigated. Two types of inert particles -3.6 mm glass beads and 3 mm Teflon cylinders (length and diameter) - were tested and, due to lower pressure drop presented by Teflon cylinders during operation of the dry vibro-fluidized bed, these particles were adopted for pulp drying process. Increasing pulp apparent viscosity caused a considerable increase in the vibro-fluidized bed pressure drop during pulp drying and, as a consequence resulted in a larger value of minimum vibro-fluidization velocity. on the other hand, the negative effect of increasing apparent viscosity could be attenuated by increasing the fluidized bed vibration intensity, which could prevent stickiness between particles. (c) 2006 Elsevier B.V. All rights reserved.

ROAD TRANSPORT IN BRAZIL: SOME TYPES of VISCOSITY

The planning of the transportation sector in Brazil has long been the railroads as the main engineering system of the country. Thus, it was used to carry, in addition to the physical integration of the national territory, the consolidation of its domestic market. However, after entering in the 1980s, the planning of the sector is left out, and an inversion of the matrix of development is observed, with share gains in monoculture economy and on development of new areas where agricultural expansion advanced. This situation culminated in logistics blackouts in the 1990s and the resumption of sector planning in the early twenty-first century. At this time, it establishes a new institutional apparatus that ensures the participation of private capital in the sector, as well as a new principle for resolving bottlenecks concentrated regions (economically dynamic), from targeting investments to areas of primary economies that only in recent decades have been incorporated into the national economy.