Fabrication and characterization of silicon position sensitive particle detectors

Position sensitive particle detectors are needed in high energy physics research. This thesis describes the development of fabrication processes and characterization techniques of silicon microstrip detectors used in the work for searching elementary particles in the European center for nuclear research, CERN. The detectors give an electrical signal along the particles trajectory after a collision in the particle accelerator. The trajectories give information about the nature of the particle in the struggle to reveal the structure of the matter and the universe. Detectors made of semiconductors have a better position resolution than conventional wire chamber detectors. Silicon semiconductor is overwhelmingly used as a detector material because of its cheapness and standard usage in integrated circuit industry. After a short spread sheet analysis of the basic building block of radiation detectors, the pn junction, the operation of a silicon radiation detector is discussed in general. The microstrip detector is then introduced and the detailed structure of a double-sided ac-coupled strip detector revealed. The fabrication aspects of strip detectors are discussedstarting from the process development and general principles ending up to the description of the double-sided ac-coupled strip detector process. Recombination and generation lifetime measurements in radiation detectors are discussed shortly. The results of electrical tests, ie. measuring the leakage currents and bias resistors, are displayed. The beam test setups and the results, the signal to noise ratio and the position accuracy, are then described. It was found out in earlier research that a heavy irradiation changes the properties of radiation detectors dramatically. A scanning electron microscope method was developed to measure the electric potential and field inside irradiated detectorsto see how a high radiation fluence changes them. The method and the most important results are discussed shortly.

Mikroliuskarakenteisen T-resonaattorin käyttö piirilevyn eristeominaisuuksien määrityksessä

Tässä diplomityössä tutkittiin ja kehitettiin edelleen mikroliuskarakenteisen T-resonaattorin käyttöä laajakaistaisessa piirilevylaminaattien dielektrisyysvakion ja häviökertoimen määrityksessä. Työssä perehdyttiin eristeominaisuuksien määrityksessä tarvittaviin laskentamenetelmiin sekä T-resonaattorin toimintaan. T-resonaattorin suunnittelu ja käyttöä varten valitut laskentamenetelmät on esitelty. Työssä suunniteltiin ja valmistettiin mikroliuskarakenteinen T-resonaattorimittausrakenne, jolla määritettiin erään FR-4 -tyyppisen piirilevylaminaattimateriaalin dielektrisyysvakio sekä häviökerroin mittausten ja laskennan avulla taajuuskaistalla 0,5 - 10 GHz. Tuloksia verrattiin muilla käytössä olevilla menetelmillä määritettyihin tuloksiin. Tulosten perusteella voitiin osoittaa, että mikroliuskarakenteinen T-resonaattori soveltuu hyvin piirilevylaminaattien eristeominaisuuksien määritykseen, ja käytetyt laskenta-menetelmät antavat realistisia tuloksia.

Kalibrointimenetelmä planaaristen siirtojohtojen mittaamiseen

Tässä diplomityössä tutkittiin TRL-kalibroinnin käyttämistä tasomaisten siirtojohtojen sähköisten parametrien määrittämisessä taajuusalueella 0,3 – 12 GHz. Työssä perehdyttiin TRL-kalibroinnin käyttämiseen piirianalysaattorilla toteutettujen mittauksien mittauskalibrointiin sekä kalibrointiin tarvittavien kalibrointistandardien mitoittamiseen. Kalibrointistandardit suunniteltiin ja toteutettiin sekä mikroliuska- että liuskajohdoille, joiden toiminnallisuutta tarkasteltiin sekä taajuustason että aikatason mittausten avulla. Työssä perehdyttiin myös kalibrointistandardien liityntärajapinnan suunniteluun ja toteuttamiseen. Saatujen tulosten perusteella voitiin osoittaa mikroliuskajohtokitin soveltuvan hyvin mittauskalibroinnin toteuttamiseen tarkoissa mittaussovelluksissa.

Johdinhäviöiden määrittäminen mikroliuskarakenteessa

Tässä diplomityössä on käsitelty mikroliuskarakenteen johdinhäviöiden määrittämistä kokeellisin ja analyyttisin menetelmin. Työssä on käyty läpi mikroliuskarakenteen ominaisuudet sekä esitetty tärkeimmät kirjallisuudessa esitellyt menetelmät johdinhäviöiden laskemiseksi. Mikroliuskarakenteen häviöitä mallinnettiin modernilla momenttimenetelmään perustuvalla kenttälaskentasimulaattorilla. Simulaattorin toimintaperiaate on esitelty ja sen soveltaminen mikroliuskarakenteen simuloimiseen on käyty läpi. Eräs mikroliuskarakenne mallinnettiin taajuusalueella 1-10 GHz ja simuloituja johdinhäviöitä verrattiin analyyttisesti määritettyihin. Mikroliuskarakenteen vaste mitattiin ja sitä verrattiin mallinnetun mikroliuskarakenteen vasteeseen. Tulosten perusteella on pohdittu simulaattorin soveltuvuutta mikroliuskarakenteen johdinhäviöiden mallintamiseen. Mikroliuskarakenteen johdinhäviöiden määrittämiseen mittausten avulla on esitetty ideoita jatkotutkimusta varten.

Modeling of fractal antennas

In this Master Thesis the characteristics of the chosen fractal microstrip antennas are investigated. For modeling has been used the structure of the square Serpinsky fractal curves. During the elaboration of this Master thesis the following steps were undertaken: 1) calculation and simulation of square microstrip antennа, 2) optimizing for obtaining the required characteristics on the frequency 2.5 GHz, 3) simulation and calculation of the second and third iteration of the Serpinsky fractal curves, 4) radiation patterns and intensity distribution of these antennas. In this Master’s Thesis the search for the optimal position of the port and fractal elements was conducted. These structures can be used in perspective for creation of antennas working at the same time in different frequency range.

Modified Circular Patch Antenna

A circular miqrostrip antenna with a modified structure is presented. By adjusting the feed location along the circumference of the patch it is possible to match the antenna with a C microstrip line of any impedance. The impedance bandwidth and radiation characteristics are unaffected by this structural V modification.

Proceedings Of Eleventh National Symposium On Antennas And Propagation

In this paper we have investigated the effect of cavity diameter and wall height on resonance and radiation characteristics of a circular microstrip patch antenna. Experiments were conducted using a fabricated prototype placed inside a cylindrical cavity. The results were compared and verified with simulated data obtained using an electromagnetic simulator. About 9.6 to 10.5 dBi peak gain was obtained from measured and simulated data

Simple Low-cost Planar Antenna for Indoor Communication under the Bluetooth Protocol

A single-feed rectangular-ring microstrip antenna is proposed for indoor communication under the Bluetooth protocol. The dimensions of the antenna together with the location of the feed point are optimized through field simulations in order to cover the Bluetooth bandwidth and to avoid linear polarization. The performance and the efficiency of the antenna are illustrated in a real indoor environment

A new broadband circular patch antenna

A simple technique to improve the impedance bandwidth of a circular microstrip patch antenna using two sectorial slots is proposed. Using this design more than 5% impedance bandwidth is obtained. The added advantage of this new antenna is that it can be fed by a 50- microstrip line

A novel H-shaped patch antenna

A novel H-shaped patch antenna suitable for wireless and satellite communications is presented. The new antenna has some advantages compared to conventional microstrip patch antennas, such as small size, a fewer number of modes, no harmonic resonance, and the provision of pure reactive impedances at its harmonics that can result in increasing the transmitter efficiency. The basic principles and design procedure are introduced. Two antennas at two different frequencies, 4 and 10 GHz, are designed, fabricated, and measured. The measured results show a good agreement with the predicted ones

A Broadband Slope-Strip-Fed Micro strip Patch Antenna

A novel slope -strip feeding technique for a microstrip antenna is presented in order to achieve a broad bandwidth. The experimental results show that the optimal bandwidth attained is 53.4% for less than -10-dB return loss

A Compact Novel Slot-Loaded Dual-Frequency H-Shaped Antenna

A novel compact single-layer dual frequency microstrip antenna which uses an H-shaped geometry with two U-shaped slots embedded near the radiation edges, is presented. By changing the design parameters, the lower and higher resonant frequencies can be controlled easily, and a range of frequency ratios (1.716-2.363) can be obtained in this design. For the two operating frequencies of the proposed antenna, the same polarization planes and broadside radiation patterns are achieved. Compared to the regular dualfrequency patch antenna, this antenna can realize a significant size reduction

A Novel Method for Switching and Tuning of PBG Structures

Photonic band-gap (PBG) structures are utilized in microwave components as filters to suppress unwanted signals. In this work, rectangular perforations were created in the ground plane of a microstrip line to construct a PBG structure. A gold-coated alumina substrate was utilized to switch or tune the bandstop characteristics of this structure. It was demonstrated that the bandstop characteristics were switched off from - 35 to - 1 dB at 16 GHz. Tuning of the bandstop edge with a shift of 1.5 GHz was also shown

T-strip-fed High-Permittivity Rectangular Dielectric Resonator Antenna for Broadband Applications

rectangular low-density, high-permittivity dielectric resona or antenna (DRA) excited by T-shaped microstrip feed offering a 2:1 VSWR bandwidth of -22% at 2.975 GHz is reported. The design methoaology and experimental results of the antenna are discussed. The excellent gain and radiation performance of the proposed antenna project: it as a potential candidate for telecommunication applications

A New Broadband Circular Patch Antenna

A simple technique to improve the impedance bandwidth of a circular microstrip patch antenna using two sectorial slots is proposed. Using this design more than 5% impedance bandwidth is obtained. The added advantage of this new antenna is that it can be fed by a 50 microstrip line.