Phase noise influence in coherent optical DnPSK systems with DSP based dispersion compensation

We present a comparative study of the influence of dispersion induced phase noise for n-level PSK systems. From the analysis, we conclude that the phase noise influence for classical homodyne/heterodyne PSK systems is entirely determined by the modulation complexity (expressed in terms of constellation diagram) and the analogue demodulation format. On the other hand, the use of digital signal processing (DSP) in homodyne/intradyne systems renders a fiber length dependence originating from the generation of equalization enhanced phase noise. For future high capacity systems, high constellations must be used in order to lower the symbol rate to practically manageable speeds, and this fact puts severe requirements to the signal and local oscillator (LO) linewidths. Our results for the bit-error-rate (BER) floor caused by the phase noise influence in the case of QPSK, 16PSK and 64PSK systems outline tolerance limitations for the LO performance: 5 MHz linewidth (at 3-dB level) for 100 Gbit/s QPSK; 1 MHz for 400 Gbit/s QPSK; 0.1 MHz for 400 Gbit/s 16PSK and 1 Tbit/s 64PSK systems. This defines design constrains for the phase noise impact in distributed-feed-back (DFB) or distributed-Bragg-reflector (DBR) semiconductor lasers, that would allow moving the system capacity from 100 Gbit/s system capacity to 400 Gbit/s in 3 years (1 Tbit/s in 5 years). It is imperative at the same time to increase the analogue to digital conversion (ADC) speed such that the single quadrature symbol rate goes from today's 25 GS/s to 100 GS/s (using two samples per symbol). © 2014 by Walter de Gruyter Berlin/Boston.

Phase noise influence in long-range coherent optical OFDM systems with delay detection, IFFT multiplexing and FFT demodulation

We present a study of the influence of dispersion induced phase noise for CO-OFDM systems using FFT multiplexing/IFFT demultiplexing techniques (software based). The software based system provides a method for a rigorous evaluation of the phase noise variance caused by Common Phase Error (CPE) and Inter-Carrier Interference (ICI) including - for the first time to our knowledge - in explicit form the effect of equalization enhanced phase noise (EEPN). This, in turns, leads to an analytic BER specification. Numerical results focus on a CO-OFDM system with 10-25 GS/s QPSK channel modulation. A worst case constellation configuration is identified for the phase noise influence and the resulting BER is compared to the BER of a conventional single channel QPSK system with the same capacity as the CO-OFDM implementation. Results are evaluated as a function of transmission distance. For both types of systems, the phase noise variance increases significantly with increasing transmission distance. For a total capacity of 400 (1000) Gbit/s, the transmission distance to have the BER < 10-2 for the worst case CO-OFDM design is less than 800 and 460 km, respectively, whereas for a single channel QPSK system it is less than 1400 and 560 km.

Phase noise tolerance study in coherent optical circular QAM transmissions with Viterbi- Viterbi carrier phase estimation

We present a performance evaluation of a non-conventional approach to implement phase noise tolerant optical systems with multilevel modulation formats. The performance of normalized Viterbi-Viterbi carrier phase estimation (V-V CPE) is investigated in detail for circular m-level quadrature amplitude modulation (C-mQAM) signals. The intrinsic property of C-mQAM constellation points with a uniform phase separation allows a straightforward employment of V-V CPE without the need to adapt constellation. Compared with conventional feed-forward CPE for square QAM signals, the simulated results show an enhanced tolerance of linewidth symbol duration product (ΔvTs) at a low sensitivity penalty by using feed-forward CPE structure with C-mQAM. This scheme can be easily upgraded to higher order modulations without inducing considerable complexity.

A thermally wavelength-tunable photonic switch based on silicon microring resonator

Silicon photonics is a very promising technology for future low-cost high-bandwidth optical telecommunication applications down to the chip level. This is due to the high degree of integration, high optical bandwidth and large speed coupled with the development of a wide range of integrated optical functions. Silicon-based microring resonators are a key building block that can be used to realize many optical functions such as switching, multiplexing, demultiplaxing and detection of optical wave. The ability to tune the resonances of the microring resonators is highly desirable in many of their applications. In this work, the study and application of a thermally wavelength-tunable photonic switch based on silicon microring resonator is presented. Devices with 10μm diameter were systematically studied and used in the design. Its resonance wavelength was tuned by thermally induced refractive index change using a designed local micro-heater. While thermo-optic tuning has moderate speed compared with electro-optic and all-optic tuning, with silicon’s high thermo-optic coefficient, a much wider wavelength tunable range can be realized. The device design was verified and optimized by optical and thermal simulations. The fabrication and characterization of the device was also implemented. The microring resonator has a measured FSR of ∼18 nm, FWHM in the range 0.1-0.2 nm and Q around 10,000. A wide tunable range (>6.4 nm) was achieved with the switch, which enables dense wavelength division multiplexing (DWDM) with a channel space of 0.2nm. The time response of the switch was tested on the order of 10 μs with a low power consumption of ∼11.9mW/nm. The measured results are in agreement with the simulations. Important applications using the tunable photonic switch were demonstrated in this work. 1×4 and 4×4 reconfigurable photonic switch were implemented by using multiple switches with a common bus waveguide. The results suggest the feasibility of on-chip DWDM for the development of large-scale integrated photonics. Using the tunable switch for output wavelength control, a fiber laser was demonstrated with Erbium-doped fiber amplifier as the gain media. For the first time, this approach integrated on-chip silicon photonic wavelength control.

A Thermally Wavelength-tunable Photonic Switch Based on Silicon Microring Resonator

Silicon photonics is a very promising technology for future low-cost high-bandwidth optical telecommunication applications down to the chip level. This is due to the high degree of integration, high optical bandwidth and large speed coupled with the development of a wide range of integrated optical functions. Silicon-based microring resonators are a key building block that can be used to realize many optical functions such as switching, multiplexing, demultiplaxing and detection of optical wave. The ability to tune the resonances of the microring resonators is highly desirable in many of their applications. In this work, the study and application of a thermally wavelength-tunable photonic switch based on silicon microring resonator is presented. Devices with 10µm diameter were systematically studied and used in the design. Its resonance wavelength was tuned by thermally induced refractive index change using a designed local micro-heater. While thermo-optic tuning has moderate speed compared with electro-optic and all-optic tuning, with silicon’s high thermo-optic coefficient, a much wider wavelength tunable range can be realized. The device design was verified and optimized by optical and thermal simulations. The fabrication and characterization of the device was also implemented. The microring resonator has a measured FSR of ~18 nm, FWHM in the range 0.1-0.2 nm and Q around 10,000. A wide tunable range (>6.4 nm) was achieved with the switch, which enables dense wavelength division multiplexing (DWDM) with a channel space of 0.2nm. The time response of the switch was tested on the order of 10 us with a low power consumption of ~11.9mW/nm. The measured results are in agreement with the simulations. Important applications using the tunable photonic switch were demonstrated in this work. 1×4 and 4×4 reconfigurable photonic switch were implemented by using multiple switches with a common bus waveguide. The results suggest the feasibility of on-chip DWDM for the development of large-scale integrated photonics. Using the tunable switch for output wavelength control, a fiber laser was demonstrated with Erbium-doped fiber amplifier as the gain media. For the first time, this approach integrated on-chip silicon photonic wavelength control.

Monte Carlo determination of the phase diagram of the double-exchange model

We study the phase diagram of the double exchange model, with antiferromagnetic interactions, in a cubic lattice both at zero and finite temperature. There is a rich variety of magnetic phases, combined with regions where phase separation takes place. We identify phases, intrinsic to the cubic lattice, which are stable for realistic values of the interactions and dopings. Some of these phases break chiral symmetry, leading to unusual features.

Systematic characterization of thermodynamic and dynamical phase behavior in systems with short-ranged attraction

In this paper we demonstrate the feasibility and utility of an augmented version of the Gibbs ensemble Monte Carlo method for computing the phase behavior of systems with strong, extremely short-ranged attractions. For generic potential shapes, this approach allows for the investigation of narrower attractive widths than those previously reported. Direct comparison to previous self-consistent Ornstein-Zernike approximation calculations is made. A preliminary investigation of out-of-equilibrium behavior is also performed. Our results suggest that the recent observations of stable cluster phases in systems without long-ranged repulsions are intimately related to gas-crystal and metastable gas-liquid phase separation.

Étude des mécanismes d’extraction lipidique par le peptide mélittine et la protéine BSP1

Les peptides et protéines extracteurs de lipides (PEL) se lient aux membranes lipidiques puis en extraient des lipides en formant de plus petits auto-assemblages, un phénomène qui peut aller jusqu'à la fragmentation des membranes. Dans la nature, cette extraction se produit sur une gamme de cellules et entraîne des conséquences variées, comme la modification de la composition de la membrane et la mort de la cellule. Cette thèse se penche sur l’extraction lipidique, ou fragmentation, induite par le peptide mélittine et la protéine Binder-of-SPerm 1 (BSP1) sur des membranes lipidiques modèles. Pour ce faire, des liposomes de différentes compositions sont préparés et incubés avec la mélittine ou la BSP1. L'association aux membranes est déterminée par la fluorescence intrinsèque des PEL, tandis que l'extraction est caractérisée par une plateforme analytique combinant des tests colorimétriques et des analyses en chromatographie en phase liquide et spectrométrie de masse (LCMS). La mélittine fait partie des peptides antimicrobiens cationiques, un groupe de PEL très répandu chez les organismes vivants. Ces peptides sont intéressants du point du vue médical étant donné leur mode d’action qui vise directement les lipides des membranes. Plusieurs de ceux-ci agissent sur les membranes des bactéries selon le mécanisme dit « en tapis », par lequel ils s’adsorbent à leur surface, forment des pores et ultimement causent leur fragmentation. Dans cette thèse, la mélittine est utilisée comme peptide modèle afin d’étudier le mécanisme par lequel les peptides antimicrobiens cationiques fragmentent les membranes. Les résultats montrent que la fragmentation des membranes de phosphatidylcholines (PC) est réduite par une déméthylation graduelle de leur groupement ammonium. L'analyse du matériel fragmenté révèle que les PC sont préférentiellement extraites des membranes, dû à un enrichissement local en PC autour de la mélittine à l'intérieur de la membrane. De plus, un analogue de la mélittine, dont la majorité des résidus cationiques sont neutralisés, est utilisé pour évaluer le rôle du caractère cationique de la mélittine native. La neutralisation augmente l'affinité du peptide pour les membranes neutres et anioniques, réduit la fragmentation des membranes neutres et augmente la fragmentation des membranes anioniques. Malgré les interactions électrostatiques entre le peptide cationique et les lipides anioniques, aucune spécificité lipidique n'est observée dans l'extraction. La BSP1 est la protéine la plus abondante du liquide séminal bovin et constitue un autre exemple de PEL naturel important. Elle se mélange aux spermatozoïdes lors de l’éjaculation et extrait des lipides de leur membrane, notamment le cholestérol et les phosphatidylcholines. Cette étape cruciale modifie la composition lipidique de la membrane du spermatozoïde, ce qui faciliterait par la suite la fécondation de l’ovule. Cependant, le contact prolongé de la protéine avec les spermatozoïdes endommagerait la semence. Cette thèse cherche donc à approfondir notre compréhension de ce délicat phénomène en étudiant le mécanisme moléculaire par lequel la protéine fragmente les membranes lipidiques. Les résultats des présents travaux permettent de proposer un mécanisme d’extraction lipidique en 3 étapes : 1) L'association à l’interface des membranes; 2) La relocalisation de l’interface vers le cœur lipidique; 3) La fragmentation des membranes. La BSP1 se lie directement à deux PC à l'interface; une quantité suffisante de PC dans les membranes est nécessaire pour permettre l'association et la fragmentation. Cette liaison spécifique ne mène généralement pas à une extraction lipidique sélective. L'impact des insaturations des chaînes lipidiques, de la présence de lysophosphatidylcholines, de phosphatidyléthanolamine, de cholestérol et de lipides anioniques est également évalué. Les présentes observations soulignent la complexe relation entre l'affinité d'un PEL pour une membrane et le niveau de fragmentation qu'il induit. L'importance de la relocalisation des PEL de l'interface vers le cœur hydrophobe des membranes pour permettre leur fragmentation est réitérée. Cette fragmentation semble s'accompagner d'une extraction lipidique préférentielle seulement lorsqu'une séparation de phase est induite au niveau de la membrane, nonobstant les interactions spécifiques PEL-lipide. Les prévalences des structures amphiphiles chez certains PEL, ainsi que de la fragmentation en auto-assemblages discoïdaux sont discutées. Finalement, le rôle des interactions électrostatiques entre les peptides antimicrobiens cationiques et les membranes bactériennes anioniques est nuancé : les résidus chargés diminueraient l'association des peptides aux membranes neutres suite à l'augmentation de leur énergie de solvatation.

Modeling of a Heat-Induced Buckling of Plates Using the Mesh-free Method

In the process of engineering design of structural shapes, the flat plate analysis results can be generalized to predict behaviors of complete structural shapes. In this case, the purpose of this project is to analyze a thin flat plate under conductive heat transfer and to simulate the temperature distribution, thermal stresses, total displacements, and buckling deformations. The current approach in these cases has been using the Finite Element Method (FEM), whose basis is the construction of a conforming mesh. In contrast, this project uses the mesh-free Scan Solve Method. This method eliminates the meshing limitation using a non-conforming mesh. I implemented this modeling process developing numerical algorithms and software tools to model thermally induced buckling. In addition, convergence analysis was achieved, and the results were compared with FEM. In conclusion, the results demonstrate that the method gives similar solutions to FEM in quality, but it is computationally less time consuming.

Étude des mécanismes d’extraction lipidique par le peptide mélittine et la protéine BSP1

Les peptides et protéines extracteurs de lipides (PEL) se lient aux membranes lipidiques puis en extraient des lipides en formant de plus petits auto-assemblages, un phénomène qui peut aller jusqu'à la fragmentation des membranes. Dans la nature, cette extraction se produit sur une gamme de cellules et entraîne des conséquences variées, comme la modification de la composition de la membrane et la mort de la cellule. Cette thèse se penche sur l’extraction lipidique, ou fragmentation, induite par le peptide mélittine et la protéine Binder-of-SPerm 1 (BSP1) sur des membranes lipidiques modèles. Pour ce faire, des liposomes de différentes compositions sont préparés et incubés avec la mélittine ou la BSP1. L'association aux membranes est déterminée par la fluorescence intrinsèque des PEL, tandis que l'extraction est caractérisée par une plateforme analytique combinant des tests colorimétriques et des analyses en chromatographie en phase liquide et spectrométrie de masse (LCMS). La mélittine fait partie des peptides antimicrobiens cationiques, un groupe de PEL très répandu chez les organismes vivants. Ces peptides sont intéressants du point du vue médical étant donné leur mode d’action qui vise directement les lipides des membranes. Plusieurs de ceux-ci agissent sur les membranes des bactéries selon le mécanisme dit « en tapis », par lequel ils s’adsorbent à leur surface, forment des pores et ultimement causent leur fragmentation. Dans cette thèse, la mélittine est utilisée comme peptide modèle afin d’étudier le mécanisme par lequel les peptides antimicrobiens cationiques fragmentent les membranes. Les résultats montrent que la fragmentation des membranes de phosphatidylcholines (PC) est réduite par une déméthylation graduelle de leur groupement ammonium. L'analyse du matériel fragmenté révèle que les PC sont préférentiellement extraites des membranes, dû à un enrichissement local en PC autour de la mélittine à l'intérieur de la membrane. De plus, un analogue de la mélittine, dont la majorité des résidus cationiques sont neutralisés, est utilisé pour évaluer le rôle du caractère cationique de la mélittine native. La neutralisation augmente l'affinité du peptide pour les membranes neutres et anioniques, réduit la fragmentation des membranes neutres et augmente la fragmentation des membranes anioniques. Malgré les interactions électrostatiques entre le peptide cationique et les lipides anioniques, aucune spécificité lipidique n'est observée dans l'extraction. La BSP1 est la protéine la plus abondante du liquide séminal bovin et constitue un autre exemple de PEL naturel important. Elle se mélange aux spermatozoïdes lors de l’éjaculation et extrait des lipides de leur membrane, notamment le cholestérol et les phosphatidylcholines. Cette étape cruciale modifie la composition lipidique de la membrane du spermatozoïde, ce qui faciliterait par la suite la fécondation de l’ovule. Cependant, le contact prolongé de la protéine avec les spermatozoïdes endommagerait la semence. Cette thèse cherche donc à approfondir notre compréhension de ce délicat phénomène en étudiant le mécanisme moléculaire par lequel la protéine fragmente les membranes lipidiques. Les résultats des présents travaux permettent de proposer un mécanisme d’extraction lipidique en 3 étapes : 1) L'association à l’interface des membranes; 2) La relocalisation de l’interface vers le cœur lipidique; 3) La fragmentation des membranes. La BSP1 se lie directement à deux PC à l'interface; une quantité suffisante de PC dans les membranes est nécessaire pour permettre l'association et la fragmentation. Cette liaison spécifique ne mène généralement pas à une extraction lipidique sélective. L'impact des insaturations des chaînes lipidiques, de la présence de lysophosphatidylcholines, de phosphatidyléthanolamine, de cholestérol et de lipides anioniques est également évalué. Les présentes observations soulignent la complexe relation entre l'affinité d'un PEL pour une membrane et le niveau de fragmentation qu'il induit. L'importance de la relocalisation des PEL de l'interface vers le cœur hydrophobe des membranes pour permettre leur fragmentation est réitérée. Cette fragmentation semble s'accompagner d'une extraction lipidique préférentielle seulement lorsqu'une séparation de phase est induite au niveau de la membrane, nonobstant les interactions spécifiques PEL-lipide. Les prévalences des structures amphiphiles chez certains PEL, ainsi que de la fragmentation en auto-assemblages discoïdaux sont discutées. Finalement, le rôle des interactions électrostatiques entre les peptides antimicrobiens cationiques et les membranes bactériennes anioniques est nuancé : les résidus chargés diminueraient l'association des peptides aux membranes neutres suite à l'augmentation de leur énergie de solvatation.

Coerced Mechanical Coarsening of Nanoparticle Assemblies

Coarsening is a ubiquitous phenomenon [1-3] that underpins countless processes in nature, including epitaxial growth [1,3,4], the phase separation of alloys, polymers and binary fluids [2], the growth of bubbles in foams5, and pattern formation in biomembranes6. Here we show, in the first real-time experimental study of the evolution of an adsorbed colloidal nanoparticle array, that tapping-mode atomic force microscopy (TM-AFM) can drive the coarsening of Au nanoparticle assemblies on silicon surfaces. Although the growth exponent has a strong dependence on the initial sample morphology, our observations are largely consistent with modified Ostwald ripening processes [7-9]. To date, ripening processes have been exclusively considered to be thermally activated, but we show that nanoparticle assemblies can be mechanically coerced towards equilibrium, representing a new approach to directed coarsening. This strategy enables precise control over the evolution of micro- and nanostructures.

Silk Fibroin And Sodium Alginate Blend: Miscibility And Physical Characteristics.

Films of silk fibroin (SF) and sodium alginate (SA) blends were prepared by solution casting technique. The miscibility of SF and SA in those blends was evaluated and scanning electron microscopy (SEM) revealed that SF/SA 25/75 wt.% blends underwent microscopic phase separation, resulting in globular structures composed mainly of SF. X-ray diffraction indicated the amorphous nature of these blends, even after a treatment with ethanol that turned them insoluble in water. Thermal analyses of blends showed the peaks of degradation of pristine SF and SA shifted to intermediate temperatures. Water vapor permeability, swelling capacity and tensile strength of SF films could be enhanced by blending with SA. Cell viability remained between 90 and 100%, as indicated by in vitro cytotoxicity test. The SF/SA blend with self-assembled SF globules can be used to modulate structural and mechanical properties of the final material and may be used in designing high performance wound dressing.

Human Mitochondrial Hsp70 (mortalin): Shedding Light On Atpase Activity, Interaction With Adenosine Nucleotides, Solution Structure And Domain Organization.

The human mitochondrial Hsp70, also called mortalin, is of considerable importance for mitochondria biogenesis and the correct functioning of the cell machinery. In the mitochondrial matrix, mortalin acts in the importing and folding process of nucleus-encoded proteins. The in vivo deregulation of mortalin expression and/or function has been correlated with age-related diseases and certain cancers due to its interaction with the p53 protein. In spite of its critical biological roles, structural and functional studies on mortalin are limited by its insoluble recombinant production. This study provides the first report of the production of folded and soluble recombinant mortalin when co-expressed with the human Hsp70-escort protein 1, but it is still likely prone to self-association. The monomeric fraction of mortalin presented a slightly elongated shape and basal ATPase activity that is higher than that of its cytoplasmic counterpart Hsp70-1A, suggesting that it was obtained in the functional state. Through small angle X-ray scattering, we assessed the low-resolution structural model of monomeric mortalin that is characterized by an elongated shape. This model adequately accommodated high resolution structures of Hsp70 domains indicating its quality. We also observed that mortalin interacts with adenosine nucleotides with high affinity. Thermally induced unfolding experiments indicated that mortalin is formed by at least two domains and that the transition is sensitive to the presence of adenosine nucleotides and that this process is dependent on the presence of Mg2+ ions. Interestingly, the thermal-induced unfolding assays of mortalin suggested the presence of an aggregation/association event, which was not observed for human Hsp70-1A, and this finding may explain its natural tendency for in vivo aggregation. Our study may contribute to the structural understanding of mortalin as well as to contribute for its recombinant production for antitumor compound screenings.

Breaking Oil-in-water Emulsions Stabilized By Yeast.

Several biotechnological processes can show an undesirable formation of emulsions making difficult phase separation and product recovery. The breakup of oil-in-water emulsions stabilized by yeast was studied using different physical and chemical methods. These emulsions were composed by deionized water, hexadecane and commercial yeast (Saccharomyces cerevisiae). The stability of the emulsions was evaluated varying the yeast concentration from 7.47 to 22.11% (w/w) and the phases obtained after gravity separation were evaluated on chemical composition, droplet size distribution, rheological behavior and optical microscopy. The cream phase showed kinetic stability attributed to mechanisms as electrostatic repulsion between the droplets, a possible Pickering-type stabilization and the viscoelastic properties of the concentrated emulsion. Oil recovery from cream phase was performed using gravity separation, centrifugation, heating and addition of demulsifier agents (alcohols and magnetic nanoparticles). Long centrifugation time and high centrifugal forces (2h/150,000×g) were necessary to obtain a complete oil recovery. The heat treatment (60°C) was not enough to promote a satisfactory oil separation. Addition of alcohols followed by centrifugation enhanced oil recovery: butanol addition allowed almost complete phase separation of the emulsion while ethanol addition resulted in 84% of oil recovery. Implementation of this method, however, would require additional steps for solvent separation. Addition of charged magnetic nanoparticles was effective by interacting electrostatically with the interface, resulting in emulsion destabilization under a magnetic field. This method reached almost 96% of oil recovery and it was potentially advantageous since no additional steps might be necessary for further purifying the recovered oil.

Estudo por espectroscopia micro-Raman dos mecanismos de separação de fase em vidros fosfatos de metais de transição

Glass-ceramics are prepared by controlled separation of crystal phases in glasses, leading to uniform and dense grain structures. On the other hand, chemical leaching of soluble crystal phases yields porous glass-ceramics with important applications. Here, glass/ceramic interfaces of niobo-, vanado- and titano-phosphate glasses were studied by micro-Raman spectroscopy, whose spatial resolution revealed the multiphase structures. Phase-separation mechanisms were also determined by this technique, revealing that interface composition remained unchanged as the crystallization front advanced for niobo- and vanadophosphate glasses (interface-controlled crystallization). For titanophosphate glasses, phase composition changed continuously with time up to the equilibrium composition, indicating a spinodal-type phase separation.