Síntese do isobutileno e seu emprego em reações de esterificação: propostas de aulas práticas de química orgânica para a graduação

An experiment for the synthesis of isobutylene from tert-butanol dehydratation using oxalic acid as catalyst, followed by preparations of tert-butyl benzoate and tert-butyl cinnamate is described. The synthesis are simple, requiring two periods of 4 hours and are suitable for undergraduate organic chemistry experimental courses.

Rendimento térmico e emissões de contaminantes atmosféricos de gasolinas formuladas com etanol, MBTE e TAEE

The specific consumption and carbon monoxide (CO) and nitrogen oxide (NO) emissions from gasolines formulated with ethanol, methyl tert-butyl ether (MTBE) and tert-amyl ethyl ether (TAEE) were evaluated in the rich, stoichiometric and lean-burn regions during the operation of an Otto-cycle engine. The use of ethanol as an additive presented high specific consumption, while gasoline formulated with TAEE showed low specific consumption with the engine operating under lean-burn conditions. The ethers evaluated here presented a low percentage of CO in the rich-burn region when compared with ethanol.

Avaliação da estabilidade oxidativa de biodiesel de óleo de girassol com antioxidantes

Biodiesel can contain unsaturated fatty acids, which are susceptible to oxidation, being able to change into polymerized compounds. In this work biodiesel was characterized according to physical-chemistry parameters and the antioxidant activity of butylated hydroxyanisole (BHA), butylated hydroxytoluene (BHT) and tert-butylhydroquinone (TBHQ) added to biofuel was analyzed. Biodiesel was submitted to accelerate oxidation in the Schaal oven test, and peroxide value was analyzed.The absorptivity values at 232 nm and 270 nm and oxidative stability in Rancimat®were determined. It was observed that TBHQ presented superior antioxidant activity than BHT and BHA.

Validação de metodologia para a determinação simultânea dos antioxidantes sintéticos em óleos vegetais, margarinas e gorduras hidrogenadas por CLAE/UV

The use of antioxidants either to prevent or retard food's lipids oxidation was approved after inquires that verified their security within a daily intake limit. In this study, the methodology was developed and validated for the analysis of synthetic antioxidants: propylgallate (PG), tert-butylhydroquinone (TBHQ), butylhydroxyanisole (BHA), octylgallate (OG) and butylhydroxytoluene (BHT) in vegetables oils, margarine and hydrogenated fats by high performance liquid chromatographic. The methodology revealed itself efficient, with recovery rates above 90% for all antioxidant substances, besides good linearity in concentration range of 40-240 mg kg-1 (r = 0,999), repeatability with CV < 3,7% and limit of quantification 16.55, 10.32, 1.40, 3.76 and 9.30 mg/kg for BHT, BHA, PG, OG and TBHQ, respectively.

Obtenção do 2-etóxi-2-metilpropano grau analítico a partir do produto comercial

Ethyl tert-butyl ether (ETBE) is produced by commercial processes to a purity of up to 96%. In recent years, several companies have started to produce ETBE, increasing the demand for standards with higher grades of purity in the area of production control and final product certification. The present work involved the development of a purification protocol for obtaining high purity ETBE from the commercial product used in the formulation of automotive gasolines, using a spinning band distillation column. The ETBE thus produced showed a purity of over 99.5%, its main contaminant being its isomer, ethyl-sec-butyl ether (ESBE).

Aplicação do delineamento simplex-centroide no estudo da cinética da oxidação de biodiesel B100 em mistura com antioxidantes sintéticos

Antioxidants are an alternative to prevent or slow the degradation of the biofuel. In this study, it was evaluated the oxidative stability of B100 biodiesel from soybean oil in the presence of three commercial synthetic antioxidants, butylated hydroxyanisole (BHA), butylated hydroxytoluene (BHT) and tert-butylhydroquinone (TBHQ), pure or blended, from the experimental design of simplex-centroid mixture. The reaction order and rate constant were also calculated for all tests. The treatment containing pure TBHQ proved to be the most effective, proven by design, the optimum mix obtained and the rate constant. Binary and ternary mixtures containing TBHQ also showed appreciable antioxidant effect.

Chemical modifications of a natural xanthone and antimicrobial activity against multidrug resistant Staphylococcus aureus and cytotoxicity against human tumor cell lines

A series of 15 ω-aminoalkoxylxanthones containing methyl, ethyl, propyl, tert-butylamino and piperidinyl moieties were synthesized from a natural xanthone isolated from a lichen species. These compounds were tested for their in vitro antibacterial properties against Gram-positive and Gram-negative bacteria and cytotoxicity against a number of human tumor cell lines was too evaluated. The newly synthesized derivatives revealed selective activity against Staphylococcus aureus (Gram-positive), and the most promising results are for a multidrug resistant strain, for which six of these compounds showed good activity (MICs 4 µg/mL). Many derivatives inhibited tumor cells growth and most compounds were active on multiple lines.

Determinação de bussulfano em plasma através de cromatografia líquida de alta eficiência com detector de arranjo de diodos e derivatização com dietilditiocarbamato de sódio

A high performance liquid chromatographic-diode array detection method for the determination of busulfan in plasma was developed and validated. Sample preparation consisted of protein precipitation followed by derivatization with sodium diethyldithiocarbamate and liquid-liquid extraction with methyl-tert-butyl ether. Chromatograms were monitored at 277 nm. Separation was carried out on a Lichrospher RP 18 column (5 µm, 250 x 4 mm). The mobile phase consisted of water and acetonitrile (20:80, v/v). The method presented adequate specificity, linearity, precision and accuracy and allowed reliable determination of busulfan in clinical plasma samples, being applied to three patients submitted to bone marrow transplantation.

Epoxidação do óleo de soja com o sistema catalítico [MoO2(acac)2]/TBHP EM [bmim][PF6]

Epoxidation of soybean oil was investigated using 1-n-butyl-3-methylimidazolium hexafluorophosphate [bmim][PF6] ionic liquid as biphasic medium with molybdenum(VI) acetylacetonate complex and tert-butyl hydroperoxide TBHP as oxidizing agent. Reaction conditions were molar ratio TBHP:number of double bonds of oil:catalyst of 100:100:1, reaction temperature of 60 ºC and reaction time between 2 and 24 h. The proposed system showed catalytic activity for epoxidation reactions under tested conditions. Reuse of ionic liquid/catalyst system for epoxidation reactions was also investigated. Evaluation of epoxidation observed in this catalytic system was done by quantitative ¹H NMR data.

A reliable method of quantification of trace copper in beverages with and without alcohol by spectrophotometry after cloud point extraction

A new cloud point extraction (CPE) method was developed for the separation and preconcentration of copper (II) prior to spectrophotometric analysis. For this purpose, 1-(2,4-dimethylphenyl) azonapthalen-2-ol (Sudan II) was used as a chelating agent and the solution pH was adjusted to 10.0 with borate buffer. Polyethylene glycol tert-octylphenyl ether (Triton X-114) was used as an extracting agent in the presence of sodium dodecylsulphate (SDS). After phase separation, based on the cloud point of the mixture, the surfactant-rich phase was diluted with acetone, and the enriched analyte was spectrophotometrically determined at 537 nm. The variables affecting CPE efficiency were optimized. The calibration curve was linear within the range 0.285-20 µg L-1 with a detection limit of 0.085 µg L-1. The method was successfully applied to the quantification of copper in different beverage samples.

MICROWAVE ACTIVATION OF IMMOBILIZED LIPASE FOR TRANSESTERIFICATION OF VEGETABLE OILS

This work investigated the effect of microwave irradiation (MW) on the ethanolysis rate of soybean and sunflower oils catalyzed by supported Novozyme 435 (Candida antarctica). The effects of tert-butanol, water addition and oil:ethanol molar ratio on transesterification were evaluated under conventional heating (CH), and under optimum reaction conditions (with no added water in the system, 10% tert-butanol and 3:1 ethanol-to-oil molar ratio). The reactions were monitored up to 24 h to determine the conditions of initial reaction velocity. The investigated variables under MW (50 W) were: reaction time (5.0-180 min) and mode of reactor operation (fixed power, dynamic and cycles) in the absence and presence of tert-butanol (10% (w/w). The measured response was the reaction conversion in ethyl esters, which was linked to the enzyme catalytic activity. The results indicated that the use of microwave improved the activity at fixed power mode. A positive effect of the association of tert-butanol and MW irradiation on the catalytic activity was observed. The reaction rate improved in the order of approximately 1.5 fold compared to that under CH with soybean oil. Using soybean oil, the enzymatic transesterification under MW for conversion to FAEE (fatty acid ethyl esters) reached >99% in 3h, while with the use of CH the conversions were about 57% under similar conditions.

APROVEITAMENTO DE RESÍDUO DE BIODIESEL PARA PREPARAÇÃO DE CARVÕES ÁCIDOS COM ELEVADA ATIVIDADE CATALÍTICA NA REAÇÃO DE ETERIFICAÇÃO DO GLICEROL

Environmentally friendly acid carbon (CG) catalysts, containing a high amount of sulfonated and oxygenated groups, were prepared from glycerin, a biodiesel waste. CGs were produced by glycerin carbonization in the presence of H2SO4 at 1:3 m:m ratio in a closed autoclave at 180ºC for different times: 0.25; 1; 3 and 6 hours (CG-0.25h; CG-1h; CG-3h and CG-6h, respectively). The catalyst properties for all carbons were evaluated in the glycerol etherification reaction with tert-butyl alcohol (TBA). The yield for mono-tert-butyl glycerol (MTBG), di-tert-butyl glycerol (DTBG) and tri-tert-butyl-glycerol (TTBG) was high and very similar for all CGs, of about 43% and 20% for the MTBG and DTBG + TTBG, respectively. Furthermore, the activity of these catalysts were close to those obtained using a commercial resin, Amberlyst-15, of about 50% and 27% for MTBG and DTBG + TTBG, respectively.

Lipase-catalyzed Approaches towards Secondary Alcohols: Intermediates for Enantiopure Drugs

The use of enantiopure intermediates for drug synthesis is a trend in pharmaceutical industry. Different physiological effects are associated with the enantiomers of chiral molecules. Thus, the safety profile of a drug based on an enantiopure active pharmaceutical ingredient is more reliable. Biocatalysis is an important tool to access enantiopure molecules. In biocatalysis, the advantage of selectivity (chemo-, regio- and stereoselectivity) is combined with the benefits of a green synthesis strategy. Chemoenzymatic syntheses of drug molecules, obtained by combining biocatalysis with modern chemical synthesis steps usually consists of fewer reaction steps, reduced waste production and improved overall synthetic efficiency both in yields and enantio- and/or diastereoselectivities compared with classical chemical synthesis. The experimental work together with the literature review clearly indicates that lipase catalysis is highly applicable in the synthesis of enantiopure intermediates of drug molecules as the basis to infer the correct stereochemistry. By lipase catalysis, enantiopure secondary alcohols used as intermediates in the synthesis of Dorzolamide, an antiglaucoma drug, were obtained. Enantiopure _-hydroxy nitriles as potential intermediates for the synthesis of antidepressant drugs with 1-aryl-3- methylaminopropan-1-ol structure were also obtained with lipases. Kinetic resolution of racemates was the main biocatalytic approach applied. Candida Antarctica lipase B, Burkholderia cepacia lipase and Thermomyces lanuginosus lipase were applied for the acylation of alcohols and the alcoholysis of their esters in organic solvents, such as in diisopropyl ether and tert-butyl methyl ether. Candida Antarctica lipase B was used under solvent free conditions for the acylation of ethyl 3-hydroxybutanoate.

Survey of transportation of liquid bulk chemicals in the Baltic Sea

This study is made as a part of the Chembaltic (Risks of Maritime Transportation of Chemicals in Baltic Sea) project which gathers information on the chemicals transported in the Baltic Sea. The purpose of this study is to provide an overview of handling volumes of liquid bulk chemicals (including liquefied gases) in the Baltic Sea ports and to find out what the most transported liquid bulk chemicals in the Baltic Sea are. Oil and oil products are also viewed in this study but only in a general level. Oils and oil products may also include chemical-related substances (e.g. certain bio-fuels which belong to MARPOL annex II category) in some cargo statistics. Chemicals in packaged form are excluded from the study. Most of the facts about the transport volumes of chemicals presented in this study are based on secondary written sources of Scandinavian, Russian, Baltic and international origin. Furthermore, statistical sources, academic journals, periodicals, newspapers and in later years also different homepages on the Internet have been used as sources of information. Chemical handling volumes in Finnish ports were examined in more detail by using a nationwide vessel traffic system called PortNet. Many previous studies have shown that the Baltic Sea ports are annually handling more than 11 million tonnes of liquid chemicals transported in bulk. Based on this study, it appears that the number may be even higher. The liquid bulk chemicals account for approximately 4 % of the total amount of liquid bulk cargoes handled in the Baltic Sea ports. Most of the liquid bulk chemicals are handled in Finnish and Swedish ports and their proportion of all liquid chemicals handled in the Baltic Sea is altogether over 50 %. The most handled chemicals in the Baltic Sea ports are methanol, sodium hydroxide solution, ammonia, sulphuric and phosphoric acid, pentanes, aromatic free solvents, xylenes, methyl tert-butyl ether (MTBE) and ethanol and ethanol solutions. All of these chemicals are handled at least hundred thousand tonnes or some of them even over 1 million tonnes per year, but since chemical-specific data from all the Baltic Sea countries is not available, the exact tonnages could not be calculated in this study. In addition to these above-mentioned chemicals, there are also other high volume chemicals handled in the Baltic Sea ports (e.g. ethylene, propane and butane) but exact tonnes are missing. Furthermore, high amounts of liquid fertilisers, such as solution of urea and ammonium nitrate in water, are transported in the Baltic Sea. The results of the study can be considered indicative. Updated information about transported chemicals in the Baltic Sea is the first step in the risk assessment of the chemicals. The chemical-specific transportation data help to target hazard or e.g. grounding/collision risk evaluations to chemicals that are handled most or have significant environmental hazard potential. Data gathered in this study will be used as background information in later stages of the Chembaltic project when the risks of the chemicals transported in the Baltic Sea are assessed to highlight the chemicals that require special attention from an environmental point of view in potential marine accident situations in the Baltic Sea area.

M-käsittelyn vaikutus lastuamalla valmistettavan tuotteen valmistuskustannuksiin

Paremmin lastuttavia M-käsiteltyjä teräksiä on käytetty yrityksissä jo yli 20 vuoden ajan. Ominaisuuksiensa ansiosta M-teräksillä on pystytty pienentämään koneistuskustannuksia ja parantamaan kilpailukykyä. Viime vuosien aikana lastuavat terät ja työstökoneet ovat kuitenkin kehittyneet ja ero M-terästen ja tavanomaisten terästen välillä on voinut kaventua. Tämän diplomityön tavoitteena oli tutkia, saavutetaanko M-teräksen käytöllä taloudellisia etuja nykyaikaisissa konepajaolosuhteissa. Tutkimuksessa vertailtiin M-käsitellyn ja tavanomaisen 42CrMo4 – teräksen koneistusta. Valmistuskokeissa tarkasteltiin terien kulumista, lastun muotoa ja pinnanlaatua. Koekappaleena toimi olakkeellinen kuusiomutteri M64 kierteellä. Tuotteita valmistettiin yli 500 kappaletta ja materiaalia poistettiin noin 2000 kg. Koetulosten perusteella tuotteille laskettiin koneistuskustannukset kuvitteellisessa yrityksessä. Ero materiaalien välillä oli suurin työvaiheissa, joissa lastuaminen oli jatkuvaa. Sisä- ja ulkosorvauksessa M-käsiteltyä terästä lastunneiden terien kestoikä oli noin kaksinkertainen ja kierteen sorvauksessa noin nelinkertainen tavalliseen teräkseen verrattuna. Hakkaavassa työstössä terien kestoikä oli molemmilla materiaaleilla sama. Työssä suoritettujen kokeiden ja kustannuslaskelmien perusteella, käyttämällä M-käsiteltyä terästä voidaan pienentää valmistuskustannuksia. Materiaalien välinen ero korostuu, kun hakkaavaa työstöä on vähän, sarjat ovat suuria ja tuotanto on miehittämätöntä.