Air-water flows down stepped chutes: turbulence and flow structure observations

Interactions between turbulent waters and atmosphere may lead to strong air-water mixing. This experimental study is focused on the flow down a staircase channel characterised by very strong flow aeration and turbulence. Interfacial aeration is characterised by strong air-water mixing extending down to the invert. The size of entrained bubbles and droplets extends over several orders of magnitude, and a significant number of bubble/droplet clusters was observed. Velocity and turbulence intensity measurements suggest high levels of turbulence across the entire air-water flow. The increase in turbulence levels, compared to single-phase flow situations, is proportional to the number of entrained particles. (C) 2002 Elsevier Science Ltd. All rights reserved.

Horizontal rotating cylinder - A compact apparatus for studying the effect of water wetting on carbon dioxide corrosion of mild steel

Water wetting is a crucial issue in carbon dioxide (CO.) corrosion of multiphase flow pipelines made from mild steel. This study demonstrates the use of a novel benchtop apparatus, a horizontal rotating cylinder, to study the effect of water wetting on CO2 corrosion of mild steel in two-phase flow. The setup is similar to a standard rotating cylinder except for its horizontal orientation and the presence of two phases-typically water and oil. The apparatus has been tested by using mass-transfer measurements and CO2 corrosion measurements in single-phase water flow. CO2 corrosion measurements were subsequently performed using a water/hexane mixture with water cuts varying between 5% and 50%. While the metal surface was primarily hydrophilic under stagnant. conditions, a variety of dynamic water wetting situations was encountered as the water cut and fluid velocity were altered. Threshold velocities were identified at various water cuts when the surface became oil-wet and corrosion stopped.

Preparation and characterization of Nickel-and cobalt-doped magnetites

Trabalho apresentado no I Simpósio Mineiro de Ciências dos Materiais, Ouro Preto, Novembro de 2001.

Simultaneous selection in progenies of yellow passion fruit using selection indices

This study aimed to evaluate the efficiency of simultaneous selection (selection indices) using estimated genetic gains in yellow passion fruit and to make a comparison between the methodologies of Mulamba & Mock and Elston. The study was conducted with 26 sib progenies of yellow passion fruit for intrinsic production characteristics including fruit number, fruit mass, fruit length and diameter, and for the fruit characteristics skin thickness, soluble solids and acidity. Two methodologies were applied: first, in the joint analysis of fruit characteristics and of intrinsic production characteristics in a single phase of selection; and second, in the analysis in two phases, in which priority was given to the intrinsic production characteristics in the first phase, and later, in the second phase, the best fruit characteristics were chosen among the progenies of the first phase. The analysis of variance was applied to the data to detect genetic variability among progenies. The Elston's selection indice was unable to provide distribution of genetic gains consistent with the purposes of the study, as it selected a single progeny of passion fruit. However, the index based on the sum of ranks of Mulamba & Mock was more suitable, as it provided a balanced distribution of gains, selecting a larger number of progenies. The methodology of selection using indices is advantageous in passion fruit, since it contributes to higher genetic gains for all the traits evaluated, and the selection in a single phase was proved efficient for progeny selection.

Projecto e implementação de um sistema de alimentação para um transformador de alta tensão

Neste trabalho pretende-se estudar, dimensionar e implementar experimentalmente de um sistema de alimentação para transformadores de alta tensão a alta frequência. Este sistema será constituído por dois elementos principais, um rectificador monofásico em ponte totalmente controlado e por um inversor de tensão. Inicialmente realizou-se um estudo sobre as diferentes topologias possíveis para o rectificador considerando diferentes tipos de carga. Realizou-se, também, um estudo sobre o circuito de geração dos impulsos de disparo dos tiristores, executado com base num circuito integrado TCA 785, dimensionou-se os elementos constituintes do circuito de disparo, e de um sistema de controlo da tensão de saída do rectificador. Posteriormente estudou-se o funcionamento do inversor de tensão, definindo-se os modos de operação e dimensionou-se um circuito ressonante tendo em conta os parâmetros construtivos do transformador que se pretende utilizar. Finalmente procedeu-se à implementação prática dos sistemas previamente dimensionados e simulados e à apresentação dos respectivos resultados.

A new chemical route to synthesise TM-doped (TM = Co, Fe) TiO2 nanoparticles

Since the discovery of ferromagnetism well above room temperature in the Co-doped TiO2 system, diluted magnetic semiconductors based on TiO2 doped with transition metals have generated great interest because of their potential use in the development of spintronic devices. The purpose of this paper is to report on a new and swift chemical route to synthesise highly stable anatase single-phase Co- and Fe-doped TiO2 nanoparticles, with dopant concentrations of up to 10 at.-% and grain sizes that range between 20 and 30 nm. Complementary structural, microstructural and chemical analyses of the different nanopowders synthesised strongly support the hypothesis that a homogeneous distribution of the dopant element in the substitutional sites of the anatase structure has been achieved. Moreover, UV/Vis diffuse reflectance spectra of powder samples show redshifts to lower energies and decreasing bandgap energies with increasing Co or Fe concentration, which is consistent with n-type doping of the TiO2 anatase matrix. Films of Co-doped TiO2 were successfully deposited onto Si (100) substrates by the dip-coating method, with suspensions of Ti1-xCOxO2 nanoparticles in ethylene glycol. ((C)Wiley-VCH Verlag GmbH & Co. KGaA, 69451 Weinheim, Germany, 2008).

Projecto, montagem e teste de uma unidade modular de detecção de radiação Geiger-Muller

Dissertação para obtenção do grau de Mestre em Engenharia Electrotécnica Ramo de Automação e Electrónica Industrial

Use of solvent extraction to remediate soils contaminated with hydrocarbons

The main objective of this research is to exploit the possibility of using an ex situ solvent extraction technique for the remediation of soils contaminated with semi-volatile petroleum hydrocarbons. The composition of the organic phase was chosen in order to form a single phase mixture with an aqueous phase and simultaneously not being disturbed (forming stable emulsions) by the soil particles hauling the contaminants. It should also permit a regeneration of the organic solvent phase. As first, we studied the miscibility domain of the chosen ternary systems constituted by ethyl acetate–acetone–water. This system proved to satisfy the previous requirements allowing for the formation of a single liquid phase mixture within a large spectrum of compositions, and also allowing for an intimate contact with the soil. Contaminants in the diesel range within different functional groups were selected: xylene, naphthalene and hexadecane. The analytical control was done by gas chromatography with FID detector. The kinetics of the extractions proved to be fast, leading to equilibrium after 10 min. The effect of the solid–liquid ratio on the extraction efficiency was studied. Lower S/L ratios (1:8, w/v) proved to be more efficient, reaching recoveries in the order of 95%. The option of extraction in multiple contacts did not improve the recovery in relation to a single contact. The solvent can be regenerated by distillation with a loss around 10%. The contaminants are not evaporated and they remain in the non-volatile phase. The global results show that the ex situ solvent extraction is technically a feasible option for the remediation of semi-volatile aromatic, polyaromatic and linear hydrocarbons.

Photoluminescence and electrical study of fluctuating potentials in Cu2ZnSnS4-based thin films

In this work, we investigated structural, morphological, electrical, and optical properties from a set of Cu2ZnSnS4 thin films grown by sulfurization of metallic precursors deposited on soda lime glass substrates coated with or without molybdenum. X-ray diffraction and Raman spectroscopy measurements revealed the formation of single-phase Cu2ZnSnS4 thin films. A good crystallinity and grain compactness of the film was found by scanning electron microscopy. The grown films are poor in copper and rich in zinc, which is a composition close to that of the Cu2ZnSnS4 solar cells with best reported efficiency. Electrical conductivity and Hall effect measurements showed a high doping level and a strong compensation. The temperature dependence of the free hole concentration showed that the films are nondegenerate. Photoluminescence spectroscopy showed an asymmetric broadband emission. The experimental behavior with increasing excitation power or temperature cannot be explained by donor-acceptor pair transitions. A model of radiative recombination of an electron with a hole bound to an acceptor level, broadened by potential fluctuations of the valence-band edge, was proposed. An ionization energy for the acceptor level in the range 29–40 meV was estimated, and a value of 172 ±2 meV was obtained for the potential fluctuation in the valence-band edge.

CuxSnSx+1 (x = 2, 3) thin films grown by sulfurization of metallic precursors deposited by dc magnetron sputtering

We report the results of the growth of Cu-Sn-S ternary chalcogenide compounds by sulfurization of dc magnetron sputtered metallic precursors. Tetragonal Cu2SnS3 forms for a maximum sulfurization temperature of 350 ºC. Cubic Cu2SnS3 is obtained at sulfurization temperatures above 400 ºC. These results are supported by XRD analysis and Raman spectroscopy measurements. The latter analysis shows peaks at 336 cm-1, 351 cm-1 for tetragonal Cu2SnS3, and 303 cm-1, 355 cm-1 for cubic Cu2SnS3. Optical analysis shows that this phase change lowers the band gap from 1.35 eV to 0.98 eV. At higher sulfurization temperatures increased loss of Sn is expected in the sulphide form. As a consequence, higher Cu content ternary compounds like Cu3SnS4 grow. In these conditions, XRD and Raman analysis only detected orthorhombic (Pmn21) phase (petrukite). This compound has Raman peaks at 318 cm-1, 348 cm-1 and 295 cm-1. For a sulfurization temperature of 450 ºC the samples present a multi-phase structure mainly composed by cubic Cu2SnS3 and orthorhombic (Pmn21) Cu3SnS4. For higher temperatures, the samples are single phase and constituted by orthorhombic (Pmn21) Cu3SnS4. Transmittance and reflectance measurements were used to estimate a band gap of 1.60 eV. For comparison we also include the results for Cu2ZnSnS4 obtained using similar growth conditions.

Growth pressure dependence of Cu2ZnSnSe4 properties

In this work, we show a set of growth conditions, for the two step process, with which the growth of CZTSe is successful and reproducible. The properties of the best CTZSe thin films grown by this method were examined by SEM/EDS, XRD, Raman scattering, AFM/EFM, transmittance and reflectance measurements, photoluminescence (PL) measurements and hot point probe. A broad emission band was observed in the photoluminescence spectrum of the CZTSe thin film. The band gap energy was estimated to be around 1.05 eV at room temperature, using the transmittance and reflectance data, and CZTSe samples show p-type conductivity with the hot point probe. The different characterization techniques show that we could grow single phase CZTSe thin films with our optimized process conditions.

Influence of selenization pressure on the growth of Cu2ZnSnSe4 films from stacked metallic layers

Cu2ZnSnSe4 (CZTSe) is a p-type semiconductor with a high absorption coefficient, 104 to 105 cm-1, and is being seen as a possible replacement for Cu(In,Ga)Se2 in thin film solar cells. Yet, there are some fundamental properties of CZTSe that are not well known, one of them is its band gap. In order to resolve its correct value it is necessary to improve the growth conditions to ensure that single phase crystalline thin films are obtained. One of the problems encountered when growing CZTSe is the loss of Sn through evaporation of SnSe. Stoichiometric films are then difficult to obtain and usually there are other phases present. One possible way to overcome this problem is to increase the pressure of growth of CZTSe. This can be done by introducing an atmosphere of an inert gas like Ar or N2. In this work we report the results of morphological, structural and optical studies of the properties of CZTSe thin films grown by selenization of DC magnetron sputtered metallic layers under different Ar pressures. The films are analysed by SEM/EDS, Raman scattering and XRD.

Simulation model for driving dynamics, energy use and power supply

Dissertação para obtenção do grau de Mestre em Engenharia Electrotécnica Ramo de Energia

Modular high-current generator for electromagnetic forming with energy recovery

A 10 kJ electromagnetic forming (EMF) modulator with energy recovery based on two resonant power modules, each containing a 4.5 kV/30-kA silicon controlled rectifier, a 1.11-mF capacitor bank and an energy recovery circuit, working in parallel to allow a maximum actuator discharge current amplitude and rate of 50 kA and 2 kA/mu s was successfully developed and tested. It can be plugged in standard single phase 230 V/16 A mains socket and the circuit is able to recover up to 32% of its initial energy, reducing the charging time of conventional EMF systems by up to 68%.

Interaction of malaria parasites with host late endocytic and autophagic pathways is essential for Plasmodium liver stage development

RESUMO: A Malária é causada por parasitas do género Plasmodium, sendo a doença parasitária mais fatal para o ser humano. Apesar de, durante o século passado, o desenvolvimento económico e a implementação de diversas medidas de controlo, tenham permitido erradicar a doença em muitos países, a Malária continua a ser um problema de saúde grave, em particular nos países em desenvolvimento. A Malária é transmitida através da picada de uma fêmea de mosquito do género Anopheles. Durante a picada, os esporozoítos são injetados na pele do hospedeiro, seguindo-se a fase hepática e obrigatória do ciclo de vida. No fígado, os esporozoítos infetam os hepatócitos onde se replicam, dentro de um vacúolo parasitário (VP) e de uma forma imunitária silenciosa, em centenas de merozoitos. Estas novas formas do parasita são as responsáveis por infetar os eritrócitos, iniciando a fase sanguínea da doença, onde se os primeiros sintomas se manifestam, tais como a característica febre cíclica. A fase hepática da doença é a menos estudada e compreendida. Mais ainda, as interações entre o VP e os organelos da células hospedeira estão ainda pouco caracterizados. Assim, neste estudo, as interações entre os organelos endocíticos e autofágicos da célula hospedeira e o VP foram dissecados, observando-se que os anfisomas, que são organelos resultantes da intersecção do dois processos de tráfego intracelular, interagem com o parasita. Descobrimos que a autofagia tem também uma importante função imunitária durante a fase hepática inicial, ao passo, que durante o desenvolvimento do parasita, já numa fase mais tardia, o parasita depende da interação com os endossomas tardios e anfisomas para crescer. Vesiculas de BSA, EGF e LC3, foram, também, observadas dentro do VP, sugerindo que os parasitas são capazes de internalizar material endocítico e autofágico do hospedeiro. Mais ainda, mostramos que esta interação depende da cinase PIKfyve, responsável pela conversão do fosfoinositidio-3-fosfato no fosfoinositidio-3,5-bifosfato, uma vez que inibindo esta cinase o parasita não é capaz de crescer normalmente. Finalmente, mostramos que a proteína TRPML1, uma proteína efetora do fosfoinositidio-3,5-bifosfato, e envolvida no processo de fusão das membranas dos organelos endocíticos e autofágicos, também é necessária para o crescimento do parasita. Desta forma, o nosso estudo sugere que a membrana do VP funde com vesiculas endocíticas e autofágicas tardias, de uma forma dependente do fositidio-3,5-bifosfato e do seu effetor TRPML1, permitindo a troca de material com a célula hospedeira. Concluindo, os nossos resultados evidenciam que o processo autofágico que ocorre na célula hospedeira tem um papel duplo durante a fase hepática da malaria. Enquanto numa fase inicial os hepatócitos usam o processo autofágico como forma de defesa contra o parasita, já durante a fase de replicação o VP funde com vesiculas autofágicas e endocíticas de forma a obter os nutrientes necessários ao seu desenvolvimento.--------- ABSTRACT: Malaria, which is caused by parasites of the genus Plasmodium, is the most deadly parasitic infection in humans. Although economic development and the implementation of control measures during the last century have erradicated the disease from many areas of the world, it remains a serious human health issue, particularly in developing countries. Malaria is transmitted by female mosquitoes of the genus Anopheles. During the mosquito blood meal, Plasmodium spp. sporozoites are injected into the skin dermis of the vertebrate host, followed by an obligatory liver stage. Upon entering the liver, Plasmodium parasites infect hepatocytes and silently replicate inside a host cell-derived parasitophorous vacuole (PV) into thousands of merozoites. These new parasite forms can infect red blood cells initiating the the blood stage of the disease which shows the characteristic febrile malaria episodes. The liver stage is the least characterized step of the malaria infection. Moreover, the interactions between the Plasmodium spp. PV and the host cell trafficking pathways are poorly understood. We dissected the interaction between Plasmodium parasites and the host cell endocytic and autophagic pathways and we found that both pathways intersect and interconnect in the close vicinity of the parasite PV, where amphisomes are formed and accumulate. Interestingly, we observed a clearance function for autophagy in hepatocytes infected with Plasmodium berghei parasites at early infection times, whereas during late liver stage development late endosomes and amphisomes are required for parasite growth. Moreover, we found the presence of internalized BSA, EGF and LC3 inside parasite vacuoles, suggesting that the parasites uptake endocytic and autophagic cargo. Furthermore, we showed that the interaction between the PV and host traffic pathways is dependent on the kinase PIKfyve, which converts the phosphoinositide PI(3)P into PI(3,5)P2, since PIKfyve inhibition caused a reduction in parasite growth. Finally, we showed that the PI(3,5)P2 effector protein TRPML1, which is involved in late endocytic and autophagic membrane fusion, is also required for parasite development. Thus, our studies suggest that the parasite parasitophorous vacuole membrane (PVM) is able to fuse with late endocytic and autophagic vesicles in a PI(3,5)P2- and TRPML1-dependent manner, allowing the exchange of material between the host cell and the parasites, necessary for the rapid development of the latter that is seen during the liver stage of infection. In conclusion, we present evidence supporting a specific and essential dual role of host autophagy during the course of Plasmodium liver infection. Whereas in the initial hours of infection the host cell uses autophagy as a cell survival mechanism to fight the infection, during the replicative phase the PV fuses with host autophagic and endocytic vesicles to obtain nutrients required for parasite growth.