Simulation of the transmission performance for equalized holographic ROADM designs

A complete simulation of the transmission performance for Equalized Holographic ROADM (Reconfigurable Optical Add-Drop Multiplexer) designs is presented in this paper. These devices can address several wavelengths from the input to different output fibres, according to the holograms stored in a SLM (Spatial Light Modulator), where all the outputs are equalized in power. All combinations of the input wavelengths are possible at the different output fibres. To simulate the transmission performance of the EH-ROADM, a software program, from Optiwave, has been used. The correspondence between physical blocks of the device (grating, SLM, lens...) and those simulated in the program (filters, losses, splitters...) has been defined in order to obtain a close agreement between the theoretical transmission performance and the simulated one. To complete the review about Equalized Holographic ROADMs some guidelines about its design have been done.

Design of equalized ROADMs devices with flexible bandwidth based on LCoS technology

This paper describes the theory, design, applications and performance of a new Reconfigurable Add-drop Multiplexer (ROADM) with flexible bandwidth allocation. The device can address several wavelengths at the input to four output fibers, according to the holograms stored in a SLM (Spatial Light Modulator), where all the outputs are equalized in power. All combinations of the input wavelengths are possible at the different output fibers. Each fiber has assigned all the signals with the same bandwidth; the possible bandwidths are 12.5GHz, 25GHz, 50GHz and 100GHz, according to ITU-T 694.1 Recommendation. It is possible to route several signals with different bandwidth in real time thanks to Liquid Crystal over Silicon (LCoS) technology.

A Role for the GSG Domain in Localizing Sam68 to Novel Nuclear Structures in Cancer Cell Lines

The GSG (GRP33, Sam68, GLD-1) domain is a protein module found in an expanding family of RNA-binding proteins. The numerous missense mutations identified genetically in the GSG domain support its physiological role. Although the exact function of the GSG domain is not known, it has been shown to be required for RNA binding and oligomerization. Here it is shown that the Sam68 GSG domain plays a role in protein localization. We show that Sam68 concentrates into novel nuclear structures that are predominantly found in transformed cells. These Sam68 nuclear bodies (SNBs) are distinct from coiled bodies, gems, and promyelocytic nuclear bodies. Electron microscopic studies show that SNBs are distinct structures that are enriched in phosphorus and nitrogen, indicating the presence of nucleic acids. A GFP-Sam68 fusion protein had a similar localization as endogenous Sam68 in HeLa cells, diffusely nuclear with two to five SNBs. Two other GSG proteins, the Sam68-like mammalian proteins SLM-1 and SLM-2, colocalized with endogenous Sam68 in SNBs. Different GSG domain missense mutations were investigated for Sam68 protein localization. Six separate classes of cellular patterns were obtained, including exclusive SNB localization and association with microtubules. These findings demonstrate that the GSG domain is involved in protein localization and define a new compartment for Sam68, SLM-1, and SLM-2 in cancer cell lines.

Encapsulação de colecalciferol (vitamina D3) por spray chilling

A indústria de alimentos está constantemente desenvolvendo produtos que fornecem, além de nutrientes, benefícios adicionais à saúde, tais como os enriquecidos com vitaminas. A vitamina D3 (colecalciferol) é sintetizada na pele durante a exposição da luz solar, controla a homeostase de cálcio e fósforo, metabolismo ósseo, pressão arterial e reabsorção renal de cálcio. O processo de microencapsulação vem sendo bastante aplicado em alimentos e um dos objetivos principais é o controle da liberação do agente ativo no momento e local desejado. A tecnologia de spray chilling é interessante para a microencapsulação de vitaminas lipossolúveis. O objetivo deste trabalho foi microencapsular vitamina D3, utilizando o método de spray chilling para a produção das micropartículas lipídicas sólidas (MLS). Para produção das MLS utilizou-se gordura vegetal com ponto de fusão em torno de 48 °C como carreador. Três tratamentos foram estabelecidos: sem aditivos (T1), com adição de 1% de cera de abelha (T2) e com 1% de lecitina de soja (T3). As micropartículas foram caracterizadas quanto à morfologia por microscopia eletrônica de varredura, tamanho médio por difração a laser, espectroscopia no infravermelho por transformada de Fourier (FTIR) e foi analisada a estabilidade da vitamina D3 durante o armazenamento a 10 e 25 °C, por meio de quantificações periódicas em cromatografia líquida de alta eficiência (CLAE). As micropartículas obtidas foram esféricas, semelhantes morfologicamente e com distribuição monocaudal de partículas. O tamanho médio das partículas variou em função dos seus ingredientes, sendo que as micropartículas produzidas apenas com vitamina e gordura foram menores em relação às demais (83,0% < 100 µm). A espectroscopia na região do infravermelho (FTIR) demonstrou que não ocorreu interação entre os ingredientes. A estabilidade da vitamina D3 encapsulada foi satisfatória ao longo de 65 dias com valores superiores a 87% para os três tratamentos e a temperatura apresentou influência na estabilidade. As MLS produzidas com cera apresentaram melhores resultados de estabilidade de vitamina D3 com valores de 90,18 ± 2,23 % após 65 dias de estocagem. Esses resultados são promissores e demostram a viabilidade da técnica de spray chilling na produção de MLS carregadas de vitamina D3, possibilitando uma futura aplicação em alimentos.

Nisāʼ al-Muslimīn

li-Fāṭimah ʻAlīyah Khānum.

Avrupa-yı Vusta siyasetinde yeni hedefler Berlin-Bağdat /

Özege, M.S. Eski harflerle,

Tarih-i umumî /

Turkish in Arabic script.

Viscosupplementation for the treatment of osteoarthritis of the knee (Review)

Background Osteoarthritis (OA) is the most prevalent chronic joint disorder worldwide and is associated with significant pain and disability. Objectives To assess the effects of viscosupplementation in the treatment of OA of the knee. The products were hyaluronan and hylan derivatives (Adant, Arthrum H, Artz (Artzal, Supartz), BioHy (Arthrease, Euflexxa, Nuflexxa), Durolane, Fermathron, Go-On, Hyalgan, Hylan G-F 20 (Synvisc Hylan G-F 20), Hyruan, NRD-101 (Suvenyl), Orthovisc, Ostenil, Replasyn, SLM-10, Suplasyn, Synject and Zeel compositum). Search strategy MEDLINE (up to January (week 1) 2006 for update), EMBASE, PREMEDLINE, Current Contents up to July 2003, and the Cochrane Central Register of Controlled Trials (CENTRAL) were searched. Specialised journals and reference lists of identified randomised controlled trials (RCTs) and pertinent review articles up to December 2005 were handsearched. Selection criteria RCTs of viscosupplementation for the treatment of people with a diagnosis of OA of the knee were eligible. Single and double-blinded studies, placebo-based and comparative studies were eligible. At least one of the four OMERACT III core set outcome measures had to be reported (Bellamy 1997). Data collection and analysis Each trial was assessed independently by two reviewers for its methodological quality using a validated tool. All data were extracted by one reviewer and verified by a second reviewer. Continuous outcome measures were analysed as weighted mean differences (WMD) with 95% confidence intervals (CI). However, where different scales were used to measure the same outcome, standardized mean differences (SMD) were used. Dichotomous outcomes were analyzed by relative risk (RR). Main results Seventy-six trials with a median quality score of 3 (range 1 to 5) were identified. Follow-up periods varied between day of last injection and eighteen months. Forty trials included comparisons of hyaluronan/hylan and placebo (saline or arthrocentesis), ten trials included comparisons of intra-articular (IA) corticosteroids, six trials included comparisons of nonsteroidal anti-inflammatory drugs (NSAIDs), three trials included comparisons of physical therapy, two trials included comparisons of exercise, two trials included comparisons of arthroscopy, two trials included comparisons of conventional treatment, and fifteen trials included comparisons of other hyaluronans/hylan. The pooled analyses of the effects of viscosupplements against 'placebo' controls generally supported the efficacy of this class of intervention. In these same analyses, differential efficacy effects were observed for different products on different variables and at different timepoints. Of note is the 5 to 13 week post injection period which showed a percent improvement from baseline of 28 to 54% for pain and 9 to 32% for function. In general, comparable efficacy was noted against NSAIDs and longer-term benefits were noted in comparisons against IA corticosteroids. In general, few adverse events were reported in the hyaluronan/hylan trials included in these analyses. Authors' conclusions Based on the aforementioned analyses, viscosupplementation is an effective treatment for OA of the knee with beneficial effects: on pain, function and patient global assessment; and at different post injection periods but especially at the 5 to 13 week post injection period. It is of note that the magnitude of the clinical effect, as expressed by the WMD and standardised mean difference (SMD) from the RevMan 4.2 output, is different for different products, comparisons, timepoints, variables and trial designs. However, there are few randomised head-to-head comparisons of different viscosupplements and readers should be cautious, therefore, in drawing conclusions regarding the relative value of different products. The clinical effect for some products, against placebo, on some variables at some timepoints is in the moderate to large effect-size range. Readers should refer to relevant tables to review specific detail given the heterogeneity in effects across the product class and some discrepancies observed between the RevMan 4.2 analyses and the original publications. Overall, the analyses performed are positive for the HA class and particularly positive for some products with respect to certain variables and timepoints, such as pain on weight bearing at 5 to 13 weeks postinjection. In general, sample-size restrictions preclude any definitive comment on the safety of the HA class of products; however, within the constraints of the trial designs employed no major safety issues were detected. In some analyses viscosupplements were comparable in efficacy to systemic forms of active intervention, with more local reactions but fewer systemic adverse events. In other analyses HA products had more prolonged effects than IA corticosteroids. Overall, the aforementioned analyses support the use of the HA class of products in the treatment of knee OA.

Process Monitoring and Defect Detection of Additive Manufacturing Using Inline Coherent Imaging

With applications ranging from aerospace to biomedicine, additive manufacturing (AM) has been revolutionizing the manufacturing industry. The ability of additive techniques, such as selective laser melting (SLM), to create fully functional, geometrically complex, and unique parts out of high strength materials is of great interest. Unfortunately, despite numerous advantages afforded by this technology, its widespread adoption is hindered by a lack of on-line, real time feedback control and quality assurance techniques. In this thesis, inline coherent imaging (ICI), a broadband, spatially coherent imaging technique, is used to observe the SLM process in 15 - 45 $\mu m$ 316L stainless steel. Imaging of both single and multilayer builds is performed at a rate of 200 $kHz$, with a resolution of tens of microns, and a high dynamic range rendering it impervious to blinding from the process beam. This allows imaging before, during, and after laser processing to observe changes in the morphology and stability of the melt. Galvanometer-based scanning of the imaging beam relative to the process beam during the creation of single tracks is used to gain a unique perspective of the SLM process that has been so far unobservable by other monitoring techniques. Single track processing is also used to investigate the possibility of a preliminary feedback control parameter based on the process beam power, through imaging with both coaxial and 100 $\mu m$ offset alignment with respect to the process beam. The 100 $\mu m$ offset improved imaging by increasing the number of bright A-lines (i.e. with signal greater than the 10 $dB$ noise floor) by 300\%. The overlap between adjacent tracks in a single layer is imaged to detect characteristic fault signatures. Full multilayer builds are carried out and the resultant ICI images are used to detect defects in the finished part and improve upon the initial design of the build system. Damage to the recoater blade is assessed using powder layer scans acquired during a 3D build. The ability of ICI to monitor SLM processes at such high rates with high resolution offers extraordinary potential for future advances in on-line feedback control of additive manufacturing.

Selective Laser Melting of the Eutectic Silver-Copper Alloy Ag 28 wt % Cu

The aim of this work was to perform a detailed investigation of the use of Selective Laser Melting (SLM) technology to process eutectic silver-copper alloy Ag 28 wt. % Cu (also called AgCu28). The processing occurred with a Realizer SLM 50 desktop machine. The powder analysis (SEM-topography, EDX, particle distribution) was reported as well as the absorption rates for the near-infrared (NIR) spectrum. Microscope imaging showed the surface topography of the manufactured parts. Furthermore, microsections were conducted for the analysis of porosity. The Design of Experiments approach used the response surface method in order to model the statistical relationship between laser power, spot distance and pulse time.

English syllable confusion and imitation in Korean bilingual and monolingual children and adults

In the present study, Korean-English bilingual (KEB) and Korean monolingual (KM) children, between the ages of 8 and 13 years, and KEB adults, ages 18 and older, were examined with one speech perception task, called the Nonsense Syllable Confusion Matrix (NSCM) task (Allen, 2005), and two production tasks, called the Nonsense Syllable Imitation Task (NSIT) and the Nonword Repetition Task (NRT; Dollaghan & Campbell, 1998). The present study examined (a) which English sounds on the NSCM task were identified less well, presumably due to interference from Korean phonology, in bilinguals learning English as a second language (L2) and in monolinguals learning English as a foreign language (FL); (b) which English phonemes on the NSIT were more challenging for bilinguals and monolinguals to produce; (c) whether perception on the NSCM task is related to production on the NSIT, or phonological awareness, as measured by the NRT; and (d) whether perception and production differ in three age-language status groups (i.e., KEB children, KEB adults, and KM children) and in three proficiency subgroups of KEB children (i.e., English-dominant, ED; balanced, BAL; and Korean-dominant, KD). In order to determine English proficiency in each group, language samples were extensively and rigorously analyzed, using software, called Systematic Analysis of Language Transcripts (SALT). Length of samples in complete and intelligible utterances, number of different and total words (NDW and NTW, respectively), speech rate in words per minute (WPM), and number of grammatical errors, mazes, and abandoned utterances were measured and compared among the three initial groups and the three proficiency subgroups. Results of the language sample analysis (LSA) showed significant group differences only between the KEBs and the KM children, but not between the KEB children and adults. Nonetheless, compared to normative means (from a sample length- and age-matched database provided by SALT), the KEB adult group and the KD subgroup produced English at significantly slower speech rates than expected for monolingual, English-speaking counterparts. Two existing models of bilingual speech perception and production—the Speech Learning Model or SLM (Flege, 1987, 1992) and the Perceptual Assimilation Model or PAM (Best, McRoberts, & Sithole, 1988; Best, McRoberts, & Goodell, 2001)—were considered to see if they could account for the perceptual and production patterns evident in the present study. The selected English sounds for stimuli in the NSCM task and the NSIT were 10 consonants, /p, b, k, g, f, θ, s, z, ʧ, ʤ/, and 3 vowels /I, ɛ, æ/, which were used to create 30 nonsense syllables in a consonant-vowel structure. Based on phonetic or phonemic differences between the two languages, English sounds were categorized either as familiar sounds—namely, English sounds that are similar, but not identical, to L1 Korean, including /p, k, s, ʧ, ɛ/—or unfamiliar sounds—namely, English sounds that are new to L1, including /b, g, f, θ, z, ʤ, I, æ/. The results of the NSCM task showed that (a) consonants were perceived correctly more often than vowels, (b) familiar sounds were perceived correctly more often than unfamiliar ones, and (c) familiar consonants were perceived correctly more often than unfamiliar ones across the three age-language status groups and across the three proficiency subgroups; and (d) the KEB children perceived correctly more often than the KEB adults, the KEB children and adults perceived correctly more often than the KM children, and the ED and BAL subgroups perceived correctly more often than the KD subgroup. The results of the NSIT showed (a) consonants were produced more accurately than vowels, and (b) familiar sounds were produced more accurately than unfamiliar ones, across the three age-language status groups. Also, (c) familiar consonants were produced more accurately than unfamiliar ones in the KEB and KM child groups, and (d) unfamiliar vowels were produced more accurately than a familiar one in the KEB child group, but the reverse was true in the KEB adult and KM child groups. The KEB children produced sounds correctly significantly more often than the KM children and the KEB adults, though the percent correct differences were smaller than for perception. Production differences were not found among the three proficiency subgroups. Perception on the NSCM task was compared to production on the NSIT and NRT. Weak positive correlations were found between perception and production (NSIT) for unfamiliar consonants and sounds, whereas a weak negative correlation was found for unfamiliar vowels. Several correlations were significant for perceptual performance on the NSCM task and overall production performance on the NRT: for unfamiliar consonants, unfamiliar vowels, unfamiliar sounds, consonants, vowels, and overall performance on the NSCM task. Nonetheless, no significant correlation was found between production on the NSIT and NRT. Evidently these are two very different production tasks, where immediate imitation of single syllables on the NSIT results in high performance for all groups. Findings of the present study suggest that (a) perception and production of L2 consonants differ from those of vowels; (b) perception and production of L2 sounds involve an interaction of sound type and familiarity; (c) a weak relation exists between perception and production performance for unfamiliar sounds; and (d) L2 experience generally predicts perceptual and production performance. The present study yields several conclusions. The first is that familiarity of sounds is an important influence on L2 learning, as claimed by both SLM and PAM. In the present study, familiar sounds were perceived and produced correctly more often than unfamiliar ones in most cases, in keeping with PAM, though experienced L2 learners (i.e., the KEB children) produced unfamiliar vowels better than familiar ones, in keeping with SLM. Nonetheless, the second conclusion is that neither SLM nor PAM consistently and thoroughly explains the results of the present study. This is because both theories assume that the influence of L1 on the perception of L2 consonants and vowels works in the same way as for production of them. The third and fourth conclusions are two proposed arguments: that perception and production of consonants are different than for vowels, and that sound type interacts with familiarity and L2 experience. These two arguments can best explain the current findings. These findings may help us to develop educational curricula for bilingual individuals listening to and articulating English. Further, the extensive analysis of spontaneous speech in the present study should contribute to the specification of parameters for normal language development and function in Korean-English bilingual children and adults.

Vocabulary and language model adaptation using information retrieval

International audience

Detecção de Salmonella em tomates (Lycopersicon esculentum mill) pelos métodos fda-bam e mini vidas-biomérieux.

Resumo: Diversos surtos de Salmonella ocasionados pelo consumo de tomate contaminados com este micro-organismo têm sido relatados ultimamente, o que torna primordial a investigação sobre a presença desse patógeno nesse alimento. Métodos que permitam a avaliação rápida da presença de Salmonella em alimentos são de suma importância. O objetivo desse estudo foi comparar o método tradicional da Food and Drug Administration - Bacteriologycal Analytical Manual (FDA-BAM) com um método rápido da mini Vitek Immuno Diagnostic System Assay (Mini?Vidas-SLM)-bioMérieux, para detecção de Salmonella Brazil inoculada artificialmente na superfície de tomates. Foram analisadas 215 amostras de tomates inoculadas artificialmente com Salmonella Brazil com níveis de inóculos variando de 0,4 a 940 UFC/tomate. Os resultados obtidos mostraram que os métodos estudados apresentaram uma ótima concordância entre si, para todas as faixas de inóculo analisadas.

A survey on mechanisms and critical parameters on solidification of selective laser melting during fabrication of Ti-6Al-4V prosthetic acetabular cup

Additive Manufacturing (AM) includes a range of approaches that correlate with computer aided design (CAD) and manufacturing by fabrication via precise layers and is a promising method for the production of medical tools. In this study, different aspects and mechanisms of solidification for curved surfaces based on equilibrium at curved interfaces, Monge patch, interfacial and Gibbs energy will be discussed. Also, the effect of capillarity, geometry, substrate temperature, cooling rate and scanning parameters in the solidification of a prosthetic acetabular cup (PAC) using selective laser melting (SLM) is analysed. The contributions of this work are analysing solidification and effective factors in this process to produce parts with a higher quality and mechanical properties such as strength, strain, porosity, relative density and hardness. Results indicate that due to the surface to volume (S/V) ratio, and the increasing effect of the radius on Monge patch, thermal stresses and surface forces are more prevalent on outer surfaces. Moreover, solidification and mechanical properties are related to capillarity, geometry, substrate temperature, cooling rate, scanning power and speed. The results also indicate the interaction of solute diffusion and heat transfer with interatomic forces in large S/V ratio and at small scales tend to improve solidification.