A Machine Learning Analysis of Twitter Sentiment to the Sandy Hook Shootings

Gun related violence is a complex issue and accounts for a large proportion of violent incidents. In the research reported in this paper, we set out to investigate the pro-gun and anti-gun sentiments expressed on a social media platform, namely Twitter, in response to the 2012 Sandy Hook Elementary School shooting in Connecticut, USA. Machine learning techniques are applied to classify a data corpus of over 700,000 tweets. The sentiments are captured using a public sentiment score that considers the volume of tweets as well as population. A web-based interactive tool is developed to visualise the sentiments and is available at this http://www.gunsontwitter.com. The key findings from this research are: (i) There are elevated rates of both pro-gun and anti-gun sentiments on the day of the shooting. Surprisingly, the pro-gun sentiment remains high for a number of days following the event but the anti-gun sentiment quickly falls to pre-event levels. (ii) There is a different public response from each state, with the highest pro-gun sentiment not coming from those with highest gun ownership levels but rather from California, Texas and New York.

An efficient MAC protocol with adaptive energy harvesting for machine-to-machine networks

In a machine-to-machine network, the throughput performance plays a very important role. Recently, an attractive energy harvesting technology has shown great potential to the improvement of the network throughput, as it can provide consistent energy for wireless devices to transmit data. Motivated by that, an efficient energy harvesting-based medium access control (MAC) protocol is designed in this paper. In this protocol, different devices first harvest energy adaptively and then contend the transmission opportunities with energy level related priorities. Then, a new model is proposed to obtain the optimal throughput of the network, together with the corresponding hybrid differential evolution algorithm, where the involved variables are energy-harvesting time, contending time, and contending probability. Analytical and simulation results show that the network based on the proposed MAC protocol has greater throughput than that of the traditional methods. In addition, as expected, our scheme has less transmission delay, further enhancing its superiority.

Electrical discharge machining of 6061 aluminium alloy

The wire electrical discharge machining (EDM) of 6061 aluminium alloy in terms of material removal rate, kerf/slit width, surface finish and wear of electrode wire for different pulse on time and wire tension was studied. Eight experiments were carried out in a wire EDM machine by varying pulse on time and wire tension. It is found that the material removal rate increases with the increase of pulse on time though the wire tension does not affect the material removal rate. It seems that the higher wire tension facilitates steady machining process, which generates low wear in wire electrode and better surface finish. The surface roughness does not change notably with the variation of pulse on time. The appearance of the machined surfaces is very similar under all the machining conditions. The machined surface contains solidified molten material, splash of materials and blisters. The increase of the pulse on time increases the wear of wire electrode due to the increase of heat input. The wear of wire electrode generates tapered slot which has higher kerf width at top side than that at bottom side. The higher electrode wear introduces higher taper.

Design Optimization of Modern Machine-drive Systems for Maximum Fault Tolerant and Optimal Operation

Modern electric machine drives, particularly three phase permanent magnet machine drive systems represent an indispensable part of high power density products. Such products include; hybrid electric vehicles, large propulsion systems, and automation products. Reliability and cost of these products are directly related to the reliability and cost of these systems. The compatibility of the electric machine and its drive system for optimal cost and operation has been a large challenge in industrial applications. The main objective of this dissertation is to find a design and control scheme for the best compromise between the reliability and optimality of the electric machine-drive system. The effort presented here is motivated by the need to find new techniques to connect the design and control of electric machines and drive systems. A highly accurate and computationally efficient modeling process was developed to monitor the magnetic, thermal, and electrical aspects of the electric machine in its operational environments. The modeling process was also utilized in the design process in form finite element based optimization process. It was also used in hardware in the loop finite element based optimization process. The modeling process was later employed in the design of a very accurate and highly efficient physics-based customized observers that are required for the fault diagnosis as well the sensorless rotor position estimation. Two test setups with different ratings and topologies were numerically and experimentally tested to verify the effectiveness of the proposed techniques. The modeling process was also employed in the real-time demagnetization control of the machine. Various real-time scenarios were successfully verified. It was shown that this process gives the potential to optimally redefine the assumptions in sizing the permanent magnets of the machine and DC bus voltage of the drive for the worst operating conditions. The mathematical development and stability criteria of the physics-based modeling of the machine, design optimization, and the physics-based fault diagnosis and the physics-based sensorless technique are described in detail. To investigate the performance of the developed design test-bed, software and hardware setups were constructed first. Several topologies of the permanent magnet machine were optimized inside the optimization test-bed. To investigate the performance of the developed sensorless control, a test-bed including a 0.25 (kW) surface mounted permanent magnet synchronous machine example was created. The verification of the proposed technique in a range from medium to very low speed, effectively show the intelligent design capability of the proposed system. Additionally, to investigate the performance of the developed fault diagnosis system, a test-bed including a 0.8 (kW) surface mounted permanent magnet synchronous machine example with trapezoidal back electromotive force was created. The results verify the use of the proposed technique under dynamic eccentricity, DC bus voltage variations, and harmonic loading condition make the system an ideal case for propulsion systems.

Machine-to-machine communications with in-network data aggregation, processing, and actuation for large-scale cyber-physical systems

Machine-to-Machine (M2M) paradigm enables machines (sensors, actuators, robots, and smart meter readers) to communicate with each other with little or no human intervention. M2M is a key enabling technology for the cyber-physical systems (CPSs). This paper explores CPS beyond M2M concept and looks at futuristic applications. Our vision is CPS with distributed actuation and in-network processing. We describe few particular use cases that motivate the development of the M2M communication primitives tailored to large-scale CPS. M2M communications in literature were considered in limited extent so far. The existing work is based on small-scale M2M models and centralized solutions. Different sources discuss different primitives. Few existing decentralized solutions do not scale well. There is a need to design M2M communication primitives that will scale to thousands and trillions of M2M devices, without sacrificing solution quality. The main paradigm shift is to design localized algorithms, where CPS nodes make decisions based on local knowledge. Localized coordination and communication in networked robotics, for matching events and robots, were studied to illustrate new directions.

Uncertainty evaluation of multivariate quantities: A case study on electrical impedance

The paper discusses the evaluation of the uncertainty of a multivariate quantity using the Law of Propagation of Uncertainty defined in the Guide to the Expression of Uncertainty in Measurement (GUM) and a Monte Carlo method according to the GUM’s Supplement 2. The quantity analysed is the electrical impedance, which is not a scalar but a complex quantity. The used measuring method allows the evaluation of the impedance and of its uncertainty in different ways and the corresponding results are presented, compared and discussed. For comparison purposes, results of the impedance uncertainty obtained using the NIST Uncertainty Machine are also presented.