Pyrolysis of industrial wastes for oil and activated carbon recovery /

Issued May 1977.

Baltimore demonstrates gas pyrolysis : resource recovery from solid waste /

Mode of access: Internet.

San Diego County demonstrates pyrolysis of solid waste : to recover liquid fuel, metals, and glass /

Grant No. S-801588.

High strength, high modulus fibers by pyrolysis of polymeric fibers

Mode of access: Internet.

Pyrolysis treatment.

Mode of access: Internet.

Ablative Pyrolysis of Beetle-killed Trees

Thesis (Ph.D.)--University of Washington, 2016-06

Solid transport in a pyrolysis pilot-scale rotary kiln: Preliminary results?stationary and dynamic results

Experiments for the investigation of the flow of granular solids in a pyrolysis pilot-scale rotary kiln are presented. These experiments consisted first in measuring the volumetric filling ratio (steady-state experiences) for several operating conditions and second in recording the exit flow rates after a positive or negative step in one of the operating parameters (dynamic experiences). A dynamical model computing the evolution of the flow rate of granular solids through the kiln has been developed based on Saeman model [Chem. Eng. Prog. 47 (1951) 508]. The simulations are compared with experimental results; the model gives good results for the rolling mode, but for the slipping mode too. (C) 2004 Elsevier B.V. All rights reserved.

Comparison of the effect of pre-treatment and catalysts on liquid quality from fast pyrolysis of biomass

The overall objective of this work was to compare the effect of pre-treatment and catalysts on the quality of liquid products from fast pyrolysis of biomass. This study investigated the upgrading of bio-oil in terms of its quality as a bio-fuel and/or source of chemicals. Bio-oil used directly as a biofuel for heat or power needs to be improved particularly in terms of temperature sensitivity, oxygen content, chemical instability, solid content, and heating values. Chemicals produced from bio-oil need to be able to meet product specifications for market acceptability. There were two main objectives in this research. The first was to examine the influence of pre-treatment of biomass on the fast pyrolysis process and liquid quality. The relationship between the method of pre-treatment of biomass feedstock to fast pyrolysis oil quality was studied. The thermal decomposition behaviour of untreated and pretreated feedstocks was studied by using a TGA (thermogravimetric analysis) and a Py-GC/MS (pyroprobe-gas chromatography/mass spectrometry). Laboratory scale reactors (100g/h, 300g/h, 1kg/h) were used to process untreated and pretreated feedstocks by fast pyrolysis. The second objective was to study the influence of numerous catalysts on fast pyrolysis liquids from wheat straw. The first step applied analytical pyrolysis (Py-GC/MS) to determine which catalysts had an effect on fast pyrolysis liquid, in order to select catalysts for further laboratory fast pyrolysis. The effect of activation, temperature, and biomass pre-treatment on catalysts were also investigated. Laboratory experiments were also conducted using the existing 300g/h fluidised bed reactor system with a secondary catalytic fixed bed reactor. The screening of catalysts showed that CoMo was a highly active catalyst, which particularly reduced the higher molecular weight products of fast pyrolysis. From these screening tests, CoMo catalyst was selected for larger scale laboratory experiments. With reference to the effect of pre-treatment work on fast pyrolysis process, a significant effect occurred on the thermal decomposition of biomass, as well as the pyrolysis products composition, and the proportion of key components in bio-oil. Torrefaction proved to have a mild influence on pyrolysis products, when compared to aquathermolysis and steam pre-treatment.

Fuels from tyres by pyrolysis in molten salts

The current annual arisings of used car/van tyres in the U.K. has been found to be around 25m (188,000 tonnes). After the established reuse industries have taken their requirements this leaves 13.5m (102,000 tonnes) waste tyres; a quantity that can no longer be satisfactorily tipped. Laboratory scale experiments have shown that tyre can be pyrolised, using a molten carbonate system as the reaction medium, at rates corresponding to 14.9-42.7 g tyre/min. per litre of melt over the range 475 and 650°C. The product yields by weight of tyre input between the same temperatures are: hydrocarbon oil 23-36 wt. %, hydrocarbon gas 7- 18 wt. %, carbonaceous char 35-40 wt. %, steel 16.7 wt. % and inorganics 5.4 wt. %. The oil and gas evolve from the reactor and can easily be collected by conventional means. The steel and inorganics remain in the reactor although on the commercial scale it is proposed that they would be removed by physical and chemical methods respectively. The char was found to pose considerable handling problems and so a method was devised by which it could be gasified in the reactor. This was best achieved by passing air at a less than stoichiometric rate which gave a gaseous product rich in carbon monoxide. In addition this action provides heat for the system as a whole. The rates at 675-9000C were in the range corresponding to 5.6- 14.89 char/min. per litre of melt. A process flow chart has been proposed for a continuous operation based on these systems. Data from theoretical and experimental studies has enabled economic evaluations of several commercial scales to be carried out. These have shown that 4,000 and 10,000 t/yr operations show a DCF rate of return around 30% while a 50,000 t/yr operation shows 60% which would be attractive to an experienced scrap operator.

Using biomass-based fuels including pyrolysis liquids for power and CHP production

The use of biomass-derived liquids (in short: bioliquids) instead of solid biomass can help overcome some of the barriers hindering a wider use of biomass in smaller-scale CHP systems. Relevant bioliquids included biodiesel, vegetable oils as well straight and upgraded pyrolysis oil. In this joint EU-Russian research project Bioliquids-CHP prime movers (engines and turbines) will be developed and modified so that these can run efficiently on bioliquids. At the same time, bioliquids will be upgraded and blended in order to facilitate their use in prime movers. Preliminary results with regard to bioliquid selection, production, and characterisation; the selection and modification of a micro gas turbine; and the development of engines and components are discussed. The research also covers NOx emission reduction and control and an assessment of the benefits and economics of bioliquids-based CHP systems in EU and Russian markets.

The development and optimisation of a fast pyrolysis process for bio-oil production

A two-tier study is presented in this thesis. The first involves the commissioning of an extant but at the time, unproven bubbling fluidised bed fast pyrolysis unit. The unit was designed for an intended nominal throughput of 300 g/h of biomass. The unit came complete with solids separation, pyrolysis vapour quenching and oil collection systems. Modifications were carried out on various sections of the system including the reactor heating, quenching and liquid collection systems. The modifications allowed for fast pyrolysis experiments to be carried out at the appropriate temperatures. Bio-oil was generated using conventional biomass feedstocks including Willow, beechwood, Pine and Miscanthus. Results from this phase of the research showed however, that although the rig was capable of processing biomass to bio-oil, it was characterised by low mass balance closures and recurrent operational problems. The problems included blockages, poor reactor hydrodynamics and reduced organic liquid yields. The less than optimal performance of individual sections, particularly the feed and reactor systems of the rig, culminated in a poor overall performance of the system. The second phase of this research involved the redesign of two key components of the unit. An alternative feeding system was commissioned for the unit. The feed system included an off the shelf gravimetric system for accurate metering and efficient delivery of biomass. Similarly, a new bubbling fluidised bed reactor with an intended nominal throughput of 500g/h of biomass was designed and constructed. The design leveraged on experience from the initial commissioning phase with proven kinetic and hydrodynamic studies. These units were commissioned as part of the optimisation phase of the study. Also as part of this study, two varieties each, of previously unreported feedstocks namely Jatropha curcas and Moringa olifiera oil seed press cakes were characterised to determine their suitability as feedstocks for liquid fuel production via fast pyrolysis. Consequently, the feedstocks were used for the production of pyrolysis liquids. The quality of the pyrolysis liquids from the feedstocks were then investigated via a number of analytical techniques. The oils from the press cakes showed high levels of stability and reduced pH values. The improvements to the design of the fast pyrolysis unit led to higher mass balance closures and increased organic liquid yields. The maximum liquid yield obtained from the press cakes was from African Jatropha press cake at 66 wt% on a dry basis.