Monitoring Stormwater Redistribution Into Low Resistivity Soils Using Noninvasive Geophysical Techniques

Water held in the unsaturated zone is important for agriculture and construction and is replenished by infiltrating rainwater. Monitoring the soil water content of clay soils using ground-penetrating radar (GPR) has not been researched, as clay soils cause attenuation of GPR signal. In this study, GPR common-midpoint soundings (CMPs) are used in the clayey soils of the Miller Run floodplain to monitor changes in the soil water content (SWC) before and after rainfall events. GPR accomplishes this task because increases in water content will increase the dielectric constant of the subsurface material, and decrease the velocity of the GPR wave. Using an empirical relationship between dielectric constant and SWC, the Topp relation, we are able to calculate a SWC from these velocity measurements. Non-invasive electromagnetics, resistivity, and seismic were performed, and from these surveys, the layering at the field site was delineated. EM characterized the horizontal variation of the soil, allowing us to target the most clay rich area. At the CMP location, resistivity indicates the vertical structure of the subsurface consists of a 40 cm thick layer with a resistivity of 100 ohm*m. Between 40 cm and 1.5 m is a layer with a resistivity of 40 ohm*m. The thickness estimates were confirmed with invasive auger and trenching methods away from the CMP location. GPR CMPs were collected relative to a July 2013 and September 2013 storm. The velocity observations from the CMPs had a precision of +/- 0.001 m/ns as assessed by repeat analysis. In the case of both storms, the GPR data showed the expected relationship between the rainstorms and calculated SWC, with the SWC increasing sharply after the rainstorm and decreasing as time passed. We compared these data to auger core samples collected at the same time as the CMPs were taken, and the volumetric analysis of the cores confirmed the trend seen in the GPR, with SWC values between 3 and 5 percent lower than the GPR estimates. Our data shows that we can, with good precision, monitor changes in the SWC of conductive soils in response to rainfall events, despite the attenuation induced by the clay.

Characterization of granite matrix porosity and pore-space geometry by in situ and laboratory methods

Most available studies of interconnected matrix porosity of crystalline rocks are based on laboratory investigations; that is, work on samples that have undergone stress relaxation and were affected by drilling and sample preparation. The extrapolation of the results to in situ conditions is therefore associated with considerable uncertainty, and this was the motivation to conduct the ‘in situ Connected Porosity’ experiment at the Grimsel Test Site (Central Swiss Alps). An acrylic resin doped with fluorescent agents was used to impregnate the microporous granitic matrix in situ around an injection borehole, and samples were obtained by overcoring. The 3-D structure of the porespace, represented by microcracks, was studied by U-stage fluorescence microscopy. Petrophysical methods, including the determination of porosity, permeability and P -wave velocity, were also applied. Investigations were conducted both on samples that were impregnated in situ and on non-impregnated samples, so that natural features could be distinguished from artefacts. The investigated deformed granites display complex microcrack populations representing a polyphase deformation at varying conditions. The crack population is dominated by open cleavage cracks in mica and grain boundary cracks. The porosity of non-impregnated samples lies slightly above 1 per cent, which is 2–2.5 times higher than the in situ porosity obtained for impregnated samples. Measurements of seismic velocities (Vp ) on spherical rock samples as a function of confining pressure, spatial direction and water saturation for both non-impregnated and impregnated samples provide further constraints on the distinction between natural and induced crack types. The main conclusions are that (1) an interconnected network of microcracks exists in the whole granitic matrix, irrespective of the distance to ductile and brittle shear zones, and (2) conventional laboratory methods overestimate the matrix porosity. Calculations of contaminant transport through fractured media often rely on matrix diffusion as a retardation mechanism.

Metal content of nodules at Sea Scope stations based upon different analysis methods

Information on possible resource value of sea floor manganese nodule deposits in the eastern north Pacific has been obtained by a study of records and collections of the 1972 Sea Scope Expedition.

Some past decision theory models for euro construction model codes and for road drainage in Spain, and modest hints with multi-criteria methods for agro and environmental assurance

The authors are from UPM and are relatively grouped, and all have intervened in different academic or real cases on the subject, at different times as being of different age. With precedent from E. Torroja and A. Páez in Madrid Spain Safety Probabilistic models for concrete about 1957, now in ICOSSAR conferences, author J.M. Antón involved since autumn 1967 for euro-steel construction in CECM produced a math model for independent load superposition reductions, and using it a load coefficient pattern for codes in Rome Feb. 1969, practically adopted for European constructions, giving in JCSS Lisbon Feb. 1974 suggestion of union for concrete-steel-al.. That model uses model for loads like Gumbel type I, for 50 years for one type of load, reduced to 1 year to be added to other independent loads, the sum set in Gumbel theories to 50 years return period, there are parallel models. A complete reliability system was produced, including non linear effects as from buckling, phenomena considered somehow in actual Construction Eurocodes produced from Model Codes. The system was considered by author in CEB in presence of Hydraulic effects from rivers, floods, sea, in reference with actual practice. When redacting a Road Drainage Norm in MOPU Spain an optimization model was realized by authors giving a way to determine the figure of Return Period, 10 to 50 years, for the cases of hydraulic flows to be considered in road drainage. Satisfactory examples were a stream in SE of Spain with Gumbel Type I model and a paper of Ven Te Chow with Mississippi in Keokuk using Gumbel type II, and the model can be modernized with more varied extreme laws. In fact in the MOPU drainage norm the redacting commission acted also as expert to set a table of return periods for elements of road drainage, in fact as a multi-criteria complex decision system. These precedent ideas were used e.g. in wide Codes, indicated in symposia or meetings, but not published in journals in English, and a condensate of contributions of authors is presented. The authors are somehow involved in optimization for hydraulic and agro planning, and give modest hints of intended applications in presence of agro and environment planning as a selection of the criteria and utility functions involved in bayesian, multi-criteria or mixed decision systems. Modest consideration is made of changing in climate, and on the production and commercial systems, and on others as social and financial.

Comparison of methods for downscaling runoff from regional climate models in Spanish basins

At present there is much literature that refers to the advantages and disadvantages of different methods of statistical and dynamical downscaling of climate variables projected by climate models. Less attention has been paid to other indirect variables, like runoff, which play a significant role in evaluating the impact of climate change on hydrological systems. Runoff presents a much greater bias in climate models than other climate variables, like temperature or precipitation. It is very important to identify the methods that minimize bias while downscaling runoff from the gridded results of climate models to the basin scale

Comparación de técnicas geofísicas para determinación de contaminación de suelos agrícolas

El objetivo del presente trabajo es evaluar los métodos de prospección geofísica que, además de servir para la caracterización hidrológica superficial en una finca de investigación vitivinícola, alcance la mayor resolutividad para la localización de contaminantes agrícolas. Con este fin se ha realizado, en primer lugar una revisión teórica de los métodos de prospección geofísica que, a priori, pueden considerarse más adecuados por cuanto reflejan en mayor medida las variaciones físicas derivadas de los efluentes químicos agrícolas de baja salinidad. Para alcanzar el objetivo del proyecto se ha realizado una serie de perfiles eléctricos de Tomografía Eléctrica y Polarización Inducida, además de un Sondeo de Resonancia Magnética Nuclear Se han obtenido mediante las técnicas tomográficas una caracterización del subsuelo para la determinación de la litología en profundidad con variaciones laterales bruscas, así como la porosidad de estas formaciones. La sección de cargabilidad (PI) ha permitido la detección de iones disueltos en el agua subterránea. Combinando estos resultados, con los obtenidos por Resonancia Magnética en la localización de las masas de agua y la permeabilidad de las rocas circundantes, somos capaces de determinar los agentes contaminantes así como su movilidad y distribución. La conclusión es que el método que resulta más efectivo para detección de contaminantes sería la combinación de todos ellos, puesto que son complementarios entre sí. ABSTRACT The main goal of this project is to evaluate the methods of geophysical prospection, also serving for surface hydrologic characterization in a research farm wine, reaching the most resoluteness for locating agricultural pollutants. To this end was made, first a theoretical review of geophysical prospecting methods that may be considered more suitable, a priori, as they reflect more closely the physical changes resulting from agricultural chemical measure low salinity. Reaching the objective of the project has made a series of Electrical Tomography profiles (ET) and Induced Polarization profiles (IP) also has conducted a drilling of Nuclear Magnetic Resonance (RMN). It was obtained by tomography characterization techniques for determining subsurface litho logy in depth and abrupt lateral variations, as well as the porosity of these formations. The chargeability Section (IP) has enabled detection of ions dissolved in groundwater. Combining these results with those that was obtained by Nuclear Magnetic Resonance with the location of groundwater body and the surrounding rocks permeability, we are able to determine the pollutants and the mobility and distribution of contaminants. The bottom line is the method more effective for detection of contaminants would be the combination of all of them because they are complementary in the environmental study.

Determinación de la amplificación sísmica local en el Campus Sur UPM mediante la técnica de sismología de microtremores ReMi.

En el Campus Sur de la Universidad Politécnica de Madrid se ha llevado a cabo un proyecto para obtener una caracterización del subsuelo mediante ensayos ReMi, en colaboración con el departamento de Geofísica del Instituto Geográfico Nacional. La técnica ReMi (Refraction Microtremor) permite, mediante ensayos geofísicos realizados localmente sobre el terreno,obtener los parámetros físicos del mismo, que resultan de especial interés en el ámbito de la ingeniería civil. Esta técnica se caracteriza por englobarse dentro de la sísmica pasiva, muy empleada en prospección geofísica y basada en la obtención del modelo subyacente de distribución de velocidades de propagación de la onda S en función de la profundidad, con la ventaja de aprovechar el ruido sísmico ambiental como fuente de energía. Fue desarrollada en el Laboratorio Sismológico de Nevada (EEUU) por Louie (2001), con el objetivo de presentar una técnica innovadora en la obtención de las velocidades de propagación de manera experimental. Presenta ciertas ventajas, como la observación directa de la dispersión de ondas superficiales,que da un buen resultado de la velocidad de onda S, siendo un método no invasivo, de bajo coste y buena resolución, aplicable en entornos urbanos o sensibles en los que tanto otras técnicas sismológicas como otras variedades de prospección presentan dificultades. La velocidad de propagación de la onda S en los 30 primeros metros VS30, es ampliamente reconocida como un parámetro equivalente válido para caracterizar geotécnicamente el subsuelo y se halla matemáticamente relacionada con la velocidad de propagación de las ondas superficiales a observar mediante la técnica ReMi. Su observación permite el análisis espectral de los registros adquiridos, obteniéndose un modelo representado por la curva de dispersión de cada emplazamiento, de modo que mediante una inversión se obtiene el modelo de velocidad de propagación en función de la profundidad. A través de estos modelos, pueden obtenerse otros parámetros de interés sismológico. Estos resultados se representan sobre mapas isométricos para obtener una relación espacial de los mismos, particularmente conocido como zonación sísmica. De este análisis se extrae que la VS30 promedio del Campus no es baja en exceso, correspondiéndose a posteriori con los resultados de amplificación sísmica, período fundamental de resonancia del lugar y profundidad del sustrato rocoso. En última instancia se comprueba que los valores de amplificación sísmica máxima y el período al cual se produce posiblemente coincidan con los períodos fundamentales de resonancia de algunos edificios del Campus. ABSTRACT In South Campus at Polytechnic University of Madrid, a project has been carried out to obtain a proper subsoil description by applying ReMi tests, in collaboration with the Department of Geophysics of the National Geographic Institute. Through geophysical tests conducted locally, the ReMi (Refraction Microtremor) technique allows to establish the physical parameters of soil, which are of special interest in the field of civil engineering. This technique is part of passive seismic methods, often used in geophysical prospecting. It focuses in obtaining the underlying model of propagation velocity distribution of the shear wave according to depth and has the advantage of being able to use seismic ambient noise as a source of energy. It was developed in the Nevada Seismological Laboratory (USA) by Louie (2001) as an innovative technique for obtaining propagation velocities experimentally. It has several other advantages, including the direct observation of the dispersion of surface waves, which allows to reliably measure S wave velocity. This is a non-invasive, low cost and good resolution method, which can be applied in urban or sensitive environments where other prospection methods present difficulties. The propagation velocity of shear waves in the first 30 meters Vs30 is widely recognized as a valid equivalent parameter to geotechnically characterize the subsurface. It is mathematically related to surface wave's velocity of propagation, which are to observe using REMI technique. Spectral analysis of acquired data sets up a model represented by the dispersion curve at each site, so that, using an inversion process, propagation velocity model in relation to depth is obtained. Through this models, other seismologically interesting parameters can be obtained. These results are represented on isometric maps in order to obtain a spatial relationship between them, a process which is known as seismic zonation. This analysis infers that Vs30 at South Campus is not alarmingly low , corresponding with subsequent results of seismic amplification, fundamental period of resonance of soil and depth of bedrock. Ultimately, it's found that calculated values of soil's fundamental periods at which maximum seismic amplification occurs, may possibly match fundamental periods of some Campus buildings.

Prospecting and mining of copper ore at Santa Rita, New Mexico,

First edition, September 1916. cf. verso of t.-p.

Quantitative radiochemical methods for the determination of the sources of natural radioactivity.

"April 1956."

Background effects in the induced polarization method of geophysical exploration : annual progress report for 1956-57 /

"June 28, 1957."

Notes on geophysical work at Marysvale, Utah /

"May 1958."

Physical, Geochemical, Geomechanical, Geophysical and Hydrodynamic Characterization and Anisotropy Assessment of Corvio Sandstone

Corvio sandstone is a ~20 m thick unit (Corvio Formation) that appears in the top section of the Frontada Formation (Campoó Group; Lower Cretaceous) located in Northern Spain in the southern margin of the Basque-Cantabrian Basin. Up to 228 plugs were cored from four 0.3 x 0.2 x 0.5 m blocks of Corvio sandstone, to perform a comprehensive characterization of the physical, mineralogical, geomechanical, geophysical and hydrodynamic properties of this geological formation, and the anisotropic assessment of the most relevant parameters. Here we present the first data set obtained on 53 plugs which covers (i) basic physical and chemical properties including density, porosity, specific surface area and elementary analysis (XRF - CHNS); (ii) the curves obtained during unconfined and confined strengths tests, the tensile strengths, the calculated static elastic moduli and the characteristic stress levels describing the brittle behaviour of the rock; (iii) P- and S-wave velocities (and dynamic elastic moduli) and their respective attenuation factors Qp and Qs, electrical resistivity for a wide range of confining stress; and (iv) permeability and transport tracer tests. Furthermore, the geophysical, permeability and transport tests were additionally performed along the three main orthogonal directions of the original blocks, in order to complete a preliminary anisotropic assessment of the Corvio sandstone.

Chemical composition of manganese nodules and a ferromanganese crust using different methods

In the 1960s and 1970s, the Kennecott Corporation conducted a number of activities in the evaluation of manganese nodule deposits as well as in their possible hydrometallurgy.

Chemical composition of nodules from two locations in the Pacific Ocean using different methods

Manganese nodules recovered in the Pacific Ocean by the U. S. Bureau of Mines and by DeepSea Ventures Ltd. are studied for their chemical composition using X microprobe and X-ray fluorescence methods.