Integrating life cycle costs and environmental impacts of composite rail car-bodies for a Korean train

Background, aim, and scope A coupled Life Cycle Costing and life cycle assessment has been performed for car-bodies of the Korean Tilting Train eXpress (TTX) project using European and Korean databases, with the objective of assessing environmental and cost performance to aid materials and process selection. More specifically, the potential of polymer composite car-body structures for the Korean Tilting Train eXpress (TTX) has been investigated. Materials and methods This assessment includes the cost of both carriage manufacturing and use phases, coupled with the life cycle environmental impacts of all stages from raw material production, through carriage manufacture and use, to end-of-life scenarios. Metallic carriages were compared with two composite options: hybrid steel-composite and full-composite carriages. The total planned production for this regional Korean train was 440 cars, with an annual production volume of 80 cars. Results and discussion The coupled analyses were used to generate plots of cost versus energy consumption and environmental impacts. The results show that the raw material and manufacturing phase costs are approximately half of the total life cycle costs, whilst their environmental impact is relatively insignificant (3-8%). The use phase of the car-body has the largest environmental impact for all scenarios, with near negligible contributions from the other phases. Since steel rail carriages weigh more (27-51%), the use phase cost is correspondingly higher, resulting in both the greatest environmental impact and the highest life cycle cost. Compared to the steel scenario, the hybrid composite variant has a lower life cycle cost (16%) and a lower environmental impact (26%). Though the full composite rail carriage may have the highest manufacturing cost, it results in the lowest total life cycle costs and lowest environmental impacts. Conclusions and recommendations This coupled cost and life cycle assessment showed that the full composite variant was the optimum solution. This case study showed that coupling of technical cost models with life cycle assessment offers an efficient route to accurately evaluate economic and environmental performance in a consistent way.

Histone H1 expression varies during the Leishmania major life cycle.

The deduced amino acid sequence of Leishmania major sw3 cDNA reveals the presence of characteristic histone H1 amino acid motifs. However, the open reading frame is of an unusually small size for histone H1 (105 amino acids) because it lacks the coding potential for the central hydrophobic globular domain of linker histones present in other eukaryotes. Here, we provide biochemical evidence that the SW3 protein is indeed a L. major nuclear histone H1, and that it is differentially expressed during the life cycle of the parasite. Due to its high lysine content, the SW3 protein can be purified to a high degree from L. major nuclear lysates with 5% perchloric acid, a histone H1 preparative method. Using an anti-SW3 antibody, this protein is detected as a 17 kDa or as a 17/19 kDa doublet in the nuclear subfraction in different L. major strains. The nuclear localization of the SW3 protein is further supported by immunofluorescence studies. During in vitro promastigote growth, both the sw3 cytoplasmic mRNA and its protein progressively accumulate within parasites from early log phase to stationary phase. Within amastigotes, the high level of H1 expression is maintained but decreases when amastigotes differentiate into promastigotes. Together, these observations suggest that the different levels of this histone H1 protein could influence the varying degrees of chromatin condensation during the life-cycle of the parasite, and provide us with tools to study this mechanism.

Role of seipin in lipid droplet morphology and hepatitis C virus life cycle.

Infectious hepatitis C virus (HCV) particle assembly starts at the surface of lipid droplets, cytoplasmic organelles responsible for neutral fat storage. We analysed the relationship between HCV and seipin, a protein involved in lipid droplet maturation. Although seipin overexpression did not affect the total mean volume occupied by lipid droplets nor the total triglyceride and cholesterol ester levels per cell, it caused an increase in the mean diameter of lipid droplets by 60 %, while decreasing their total number per cell. The latter two effects combined resulted in a 34 % reduction of the total outer surface area of lipid droplets per cell, with a proportional decrease in infectious viral particle production, probably due to a defect in particle assembly. These results suggest that the available outer surface of lipid droplets is a critical factor for HCV release, independent of the neutral lipid content of the cell.

Applying the principles of life cycle assessment and costing in process modeling to examine profit-making capability

Static process simulation has traditionally been used to model complex processes for various purposes. However, the use of static processsimulators for the preparation of holistic examinations aiming at improving profit-making capability requires a lot of work because the production of results requires the assessment of the applicability of detailed data which may be irrelevant to the objective. The relevant data for the total assessment gets buried byirrelevant data. Furthermore, the models do not include an examination of the maintenance or risk management, and economic examination is often an extra property added to them which can be performed with a spreadsheet program. A process model applicable to holistic economic examinations has been developed in this work. The model is based on the life cycle profit philosophy developed by Hagberg and Henriksson in 1996. The construction of the model has utilized life cycle assessment and life cycle costing methodologies with a view to developing, above all, a model which would be applicable to the economic examinations of complete wholes and which would require the need for information focusing on aspects essential to the objectives. Life cycle assessment and costing differ from each other in terms of the modeling principles, but the features of bothmethodologies can be used in the development of economic process modeling. Methods applicable to the modeling of complex processes can be examined from the viewpoint of life cycle methodologies, because they involve the collection and management of large corpuses of information and the production of information for the needs of decision-makers as well. The results of the study shows that on the basis of the principles of life cycle modeling, a process model can be created which may be used to produce holistic efficiency examinations on the profit-making capability of the production line, with fewer resources thanwith traditional methods. The calculations of the model are based to the maximum extent on the information system of the factory, which means that the accuracyof the results can be improved by developing information systems so that they can provide the best information for this kind of examinations.

Data collection and criticality analysis for cost effective maintenance during the life cycle of a flue gas line

Työn tarkoituksena oli kerätä käyttövarmuustietoa savukaasulinjasta kahdelta suomalaiselta sellutehtaalta niiden käyttöönotosta aina tähän päivään asti. Käyttövarmuustieto koostuu luotettavuustiedoista sekä kunnossapitotiedoista. Kerätyn tiedon avulla on mahdollista kuvata tarkasti laitoksen käyttövarmuutta seuraavilla tunnusluvuilla: suunnittelemattomien häiriöiden lukumäärä ja korjausajat, laitteiden seisokkiaika, vikojen todennäköisyys ja korjaavan kunnossapidon kustannukset suhteessa savukaasulinjan korjaavan kunnossapidon kokonaiskustannuksiin. Käyttövarmuustiedon keräysmetodi on esitelty. Savukaasulinjan kriittisten laitteiden määrittelyyn käytetty metodi on yhdistelmä kyselytutkimuksesta ja muunnellusta vian vaikutus- ja kriittisyysanalyysistä. Laitteiden valitsemiskriteerit lopulliseen kriittisyysanalyysiin päätettiin käyttövarmuustietojen sekä kyselytutkimuksen perusteella. Kriittisten laitteiden määrittämisen tarkoitus on löytää savukaasulinjasta ne laitteet, joiden odottamaton vikaantuminen aiheuttaa vakavimmat seuraukset savukaasulinjan luotettavuuteen, tuotantoon, turvallisuuteen, päästöihin ja kustannuksiin. Tiedon avulla rajoitetut kunnossapidon resurssit voidaan suunnata oikein. Kriittisten laitteiden määrittämisen tuloksena todetaan, että kolme kriittisintä laitetta savukaasulinjassa ovat molemmille sellutehtaille yhteisesti: savukaasupuhaltimet, laahakuljettimet sekä ketjukuljettimet. Käyttövarmuustieto osoittaa, että laitteiden luotettavuus on tehdaskohtaista, mutta periaatteessa samat päälinjat voidaan nähdä suunnittelemattomien vikojen todennäköisyyttä esittävissä kuvissa. Kustannukset, jotka esitetään laitteen suunnittelemattomien kunnossapitokustannusten suhteena savukaasulinjan kokonaiskustannuksiin, noudattelevat hyvin pitkälle luotettavuuskäyrää, joka on laskettu laitteen seisokkiajan suhteena käyttötunteihin. Käyttövarmuustiedon keräys yhdistettynä kriittisten laitteiden määrittämiseen mahdollistavat ennakoivan kunnossapidon oikean kohdistamisen ja ajoittamisen laitteiston elinaikana siten, että luotettavuus- ja kustannustehokkuusvaatimukset saavutetaan.

Integration of Economics into Life Cycle Assessment in the Finnish Pulp and Paper Industry

Taloudellisen laskennan yhdistäminen elinkaariarviointiin (LCA) on alkanut kiinnostaa eri teollisuuden aloja maailmanlaajuisesti viime aikoina. Useat LCA-tietokoneohjelmat sisältävät kustannuslaskentaominaisuuksia ja yksittäiset projektit ovat yhdistäneet ympäristö- ja talouslaskentamenetelmiä. Tässä projektissa tutkitaan näiden yhdistelmien soveltuvuutta suomalaiselle sellu- ja paperiteollisuudelle, sekä kustannuslaskentaominaisuuden lisäämistä KCL:n LCA-ohjelmaan, KCL-ECO 3.0:aan. Kaikki tutkimuksen aikana löytyneet menetelmät, jotka yhdistävät LCA:n ja taloudellista laskentaa, on esitelty tässä työssä. Monet näistä käyttävät elinkaarikustannusarviointia (LCCA). Periaatteessa elinkaari määritellään eri tavalla LCCA:ssa ja LCA:ssa, mikä luo haasteita näiden menetelmien yhdistämiselle. Sopiva elinkaari tulee määritellä laskennan tavoitteiden mukaisesti. Työssä esitellään suositusmenetelmä, joka lähtee suomalaisen sellu- ja paperiteollisuuden erikoispiirteistä. Perusvaatimuksena on yhteensopivuus tavanomaisesti paperin LCA:ssa käytetyn elinkaaren kanssa. Menetelmän yhdistäminen KCL-ECO 3.0:aan on käsitelty yksityiskohtaisesti.

Life cycle costs in heating, ventilation and air-conditioning systems with drive

Energy consumption and energy efficiency have become an issue. Energy consumption is rising all over the world and because of that, and the climate change, energy is becoming more and more expensive. Buildings are major consumers of energy, and inside the buildings the major consumers are heating, ventilation and air-conditioning systems. They usually run at constant speed without efficient control. In most cases HVAC equipment is also oversized. Traditionally heating, ventilation and air-conditioning systems have been sized to meet conditions that rarely occur. The theory part in this thesis represents the basics of life cycle costs and calculations for the whole life cycle of a system. It also represents HVAC systems, equipment, systems controls and ways to save energy in these systems. The empirical part of this thesis represents life cycle cost calculations for HVAC systems. With these calculations it is possible to compute costs for the whole life cycle for the wanted variables. Life cycle costs make it possible to compare which variable causes most of the costs from the whole life point of view. Life cycle costs were studied through two real life cases which were focused on two different kinds of HVAC systems. In both of these cases the renovations were already made, so that the comparison between the old and the new, now existing system would be easier. The study indicates that energy can be saved in HVAC systems by using variable speed drive as a control method.

Elinkaaripohjaiseen ABC-analyysiin perustuva päätöksenteontukijärjestelmä

Yritysten vaihto-omaisuudenhallinnasta löytyy usein selviä puutteita. Yksi selkeä syy tähän on perinteisen ABC-analyysin riittämättömyys, joka pohjautuu puhtaasti historiatietoihin. ABC-analyysia oikein tulkitsemalla, voi siitä kuitenkin saada erinomaisen työkalun varastonhallintaan. Tämä edellyttää tuotteen elinkaarenvaiheen huomioimista. Tätä elinkaarenvaiheet huomioivaa ABC-analyysia kutsutaan elinkaaripohjaiseksi ABC-analyysiksi. Koska nykyisissä toiminnanohjausjärjestelmissä ei kuitenkaan ole mahdollista luokitella tuotteita tämän uuden menetelmän mukaisesti, syntyy tarve tukijärjestelmälle. Tukijärjestelmän tarkoituksena on sekä luokitella tuotteet elinkaaripohjaisen ABC-analyysin avulla että antaa tuotteille varastonohjaussuositukset Salmivuori Consulting Oy:n käyttämän ohjausmenetelmän mukaisesti. Varastotasojen määrittämistä helpottamaan luotiin järjestelmän yhteyteen vielä erillinen ohjaustyökalu. Lisäksi työssä on havainnollistettu keskimääräistä varaston arvoa sekä puutekustannuksia minimoivien varastotasojen valintaa case-esimerkin avulla. Järjestelmän luomien tuoteluokkien sekä varastonohjaussuositusten avulla, päätöksentekijällä on mahdollisuudet tehostaa yrityksen vaihto-omaisuudenhallintaa.

Customer relationship management through life cycle analysis, case professional service firm in B2B market

The objective of this master’s thesis was to study how customer relationships should be assessed and categorized in order to support customer relationship management (CRM) in the context of business-to-business (B2B) and professional services. This sophisticated and complex market is utilizing possibilities of CRM only rarely and even then the focus is often on technology. The theoretical part considered first CRM from the value chain point of view and then discussed the cyclical nature of relationships. The case study focused on B2B professional service firm. The data was collected from company databases and included the sample of 90 customers. The research was conducted in three phases first studying the age, then the service type of relationships and finally executing the cluster analysis. The data was analysed by statistical analysis program SAS Enterprise Guide. The results indicate that there are great differences between developments of customer relationships. While some relationships are dynamically growing and changing, most of customers are remaining constant. This implies expectations and requirements of customers are similarly divergent and relationships should be managed accordingly.

The holistic military capability life cycle model

Abstract - This paper reviews existing military capability models and the capability life cycle. It proposes a holistic capability life-cycle model (HCLCM) that combines capability systems with related capability models. ISO 15288 standard is used as a framework to construct the HCLCM. The HCLCM also shows how capability models and systems relate to each other throughout the capability life cycle. The main contribution of this paper is conceptual in nature. The model complements the existing, but still evolving, understanding of the military capability life cycle in a holistic and systemic way. The model also increases understanding and facilitates communication among various military capability stakeholders.

Creating an open-books implementation framework for a maintenance-related value-based life-cycle model

This study is a qualitative action research by its nature with elements of personal design in the form of a tangible model implementation framework construction. Utilized empirical data has been gathered via two questionnaires in relation to the arranged four workshop events with twelve individual participants. Five of them represented maintenance customers, three maintenance service providers and four equipment providers respectively. Further, there are two main research objectives in proportion to the two complementary focusing areas of this thesis. Firstly, the value-based life-cycle model, which first version has already been developed prior to this thesis, requires updating in order to increase its real-life applicability as an inter-firm decision-making tool in industrial maintenance. This first research objective is fulfilled by improving appearance, intelligibility and usability of the above-mentioned model. In addition, certain new features are also added. The workshop participants from the collaborating companies were reasonably pleased with made changes, although further attention will be required in future on the model’s intelligibility in particular as main results, charts and values were all reckoned as slightly hard to understand. Moreover, upgraded model’s appearance and added new features satisfied them the most. Secondly and more importantly, the premises of the model’s possible inter-firm implementation process need to be considered. This second research objective is delivered in two consecutive steps. At first, a bipartite open-books supported implementation framework is created and its different characteristics discussed in theory. Afterwards, the prerequisites and the pitfalls of increasing inter-organizational information transparency are studied in empirical context. One of the main findings was that the organizations are not yet prepared for network-wide information disclosure as dyadic collaboration was favored instead. However, they would be willing to share information bilaterally at least. Another major result was that the present state of companies’ cost accounting systems will definitely need implementation-wise enhancing in future since accurate and sufficiently detailed maintenance data is not available. Further, it will also be crucial to create supporting and mutually agreed network infrastructure. There are hardly any collaborative models, methods or tools currently in usage. Lastly, the essential questions about mutual trust and predominant purchasing strategies are cooperation-wise important. If inter-organizational activities are expanded, a more relational approach should be favored in this regard. Mutual trust was also recognized as a significant cooperation factor, but it is hard to measure in reality.

Sm14 gene expression in different stages of the Schistosoma mansoni life cycle and immunolocalization of the Sm14 protein within the adult worm

Sm14 is a 14-kDa vaccine candidate antigen from Schistosoma mansoni that seems to be involved in cytoplasmic trafficking of fatty acids. Although schistosomes have a high requirement for lipids, they are not able to synthesize fatty acids and sterols de novo. Thus, they must acquire host lipids. In order to determine whether Sm14 is present in different stages of the life cycle of the parasite, we performed RT-PCR. Sm14 mRNA was identified in all stages of the life cycle studied, mainly schistosomulum, adult worm and egg. Additionally, we used a rabbit anti-Sm14 polyclonal antibody in an indirect immunofluorescence assay to localize Sm14 in adult worm sections. The basal lamella of the tegument and the gut epithelium were strongly labeled. These tissues have a high flow of and demand for lipids, a finding that supports the putative role of Sm14 as an intracellular transporter of fatty acids from host cells.

Novel virtual environment and real-time simulation based methods for improving life-cycle efficiency of non-road mobile machinery

Virtual environments and real-time simulators (VERS) are becoming more and more important tools in research and development (R&D) process of non-road mobile machinery (NRMM). The virtual prototyping techniques enable faster and more cost-efficient development of machines compared to use of real life prototypes. High energy efficiency has become an important topic in the world of NRMM because of environmental and economic demands. The objective of this thesis is to develop VERS based methods for research and development of NRMM. A process using VERS for assessing effects of human operators on the life-cycle efficiency of NRMM was developed. Human in the loop simulations are ran using an underground mining loader to study the developed process. The simulations were ran in the virtual environment of the Laboratory of Intelligent Machines of Lappeenranta University of Technology. A physically adequate real-time simulation model of NRMM was shown to be reliable and cost effective in testing of hardware components by the means of hardware-in-the-loop (HIL) simulations. A control interface connecting integrated electro-hydraulic energy converter (IEHEC) with virtual simulation model of log crane was developed. IEHEC consists of a hydraulic pump-motor and an integrated electrical permanent magnet synchronous motorgenerator. The results show that state of the art real-time NRMM simulators are capable to solve factors related to energy consumption and productivity of the NRMM. A significant variation between the test drivers is found. The results show that VERS can be used for assessing human effects on the life-cycle efficiency of NRMM. HIL simulation responses compared to that achieved with conventional simulation method demonstrate the advances and drawbacks of various possible interfaces between the simulator and hardware part of the system under study. Novel ideas for arranging the interface are successfully tested and compared with the more traditional one. The proposed process for assessing the effects of operators on the life-cycle efficiency will be applied for wider group of operators in the future. Driving styles of the operators can be analysed statistically from sufficient large result data. The statistical analysis can find the most life-cycle efficient driving style for the specific environment and machinery. The proposed control interface for HIL simulation need to be further studied. The robustness and the adaptation of the interface in different situations must be verified. The future work will also include studying the suitability of the IEHEC for different working machines using the proposed HIL simulation method.

Effects of life cycle profits on the profitability of industrial heavy duty cranes

The goal of the thesis was to investigate how much after-sales profits a crane sale generates over the life cycle of the crane and the effects of these after-sales profits on the overall profitability of the crane. The thesis utilizes theories about life cycle costing from an equipment and service supplier’s point of view. However, instead of costs, the thesis is focused on the life cycle after-sales profits from maintenance services and spare parts provided for the sold crane. The case study approach was chosen and a total of five cranes from three different segments were investigated. An eight-step life cycle profit calculation model was developed in order to analyze the chosen cases’ life cycle profits systematically. The results of the investigation suggest that the life cycle after-sales profits are significant in value. In the case analyses they accounted for between 20% and 44% of the overall life cycle profits of the case cranes. The after-sales profits should be taken into account already in the pricing when offering a crane to a customer.