Extraction of volatile oil from aromatic plants with supercritical carbon dioxide: experiments and modeling

An overview of the studies carried out in our laboratories on supercritical fluid extraction (SFE) of volatile oils from seven aromatic plants: pennyroyal (Mentha pulegium L.), fennel seeds (Foeniculum vulgare Mill.), coriander (Coriandrum sativum L.), savory (Satureja fruticosa Beguinot), winter savory (Satureja montana L.), cotton lavender (Santolina chamaecyparisus) and thyme (Thymus vulgaris), is presented. A flow apparatus with a 1 L extractor and two 0.27 L separators was built to perform studies at temperatures ranging from 298 to 353 K and pressures up to 30.0 MPa. The best compromise between yield and composition compared with hydrodistillation (HD) was achieved selecting the optimum experimental conditions of extraction and fractionation. The major differences between HD and SFE oils is the presence of a small percentage of cuticular waxes and the relative amount of thymoquinone, an oxygenated monoterpene with important biological properties, which is present in the oils from thyme and winter savory. On the other hand, the modeling of our data on supercritical extraction of volatile oil from pennyroyal is discussed using Sovova's models. These models have been applied successfully to the other volatile oil extractions. Furthermore, other experimental studies involving supercritical CO2 carried out in our laboratories are also mentioned.

Medicinal plants: Past and present uses in several communities from the North-eastern Portugal

XX Symposium of Brazilian Medicinal Plants & X International Congress of Ethnopharmacology. S. Paulo, Brasil.

Epidemiologic study of bronchopulmonary mycosis in the province of cordoba, argentina

An epidemiological study for histoplasmosis coccidioidomycosis and cryptococcosis made in five areas of the province of Córdoba is presented. The data obtained showed a global positivity of 41.1% for histoplasmin 26.7% for coccidioidin and 14.1% for cryptococcin. In some areas, the Rio III basin and Traslasierra, the histoplasmosis infection indexes were much higher, 53,3% and 73.1% respectively. The index of positive skin tests with Cryptococcus antigen in Traslasierra was also very high: 31.9%.

Assessment of direct radiological risk and indirect associated toxic risks originated by Coal-Fired Power Plants

Over the past few decades there has been some discussion concerning the increase of the natural background radiation originated by coal-fired power plants, due to the uranium and thorium content present in combustion ashes. The radioactive decay products of uranium and thorium, such as radium, radon, polonium, bismuth and lead, are also released in addition to a significant amount of 40K. Since the measurement of radioactive elements released by the gaseous emissions of coal power plants is not compulsory, there is a gap of information concerning this situation. Consequently, the prediction of dispersion and mobility of these elements in the environment, after their release, is based on limited data and the radiological impact from the exposure to these radioactive elements is unknown. This paper describes the methodology that is being developed to assess the radiological impact due to the raise in the natural background radiation level originated by the release and dispersion of the emitted radionuclides. The current investigation is part of a research project that is undergoing in the vicinity of Sines coal-fired power plant (south of Portugal) until 2013. Data from preliminary stages are already available and possible of interpretation.

Radiological impact associated to Technologically Enhanced Naturally Occurring Radioactive Materials (TENORM) from coal-fired power plants emissions

Certain materials used and produced in a wide range of non-nuclear industries contain enhanced activity concentrations of natural radionuclides. In particular, electricity production from coal is one of the major sources of increased human exposure to naturally occurring radioactive materials. A methodology was developed to assess the radiological impact due to natural radiation background. The developed research was applied to a specific case study, the Sines coal-fired power plant, located in the southwest coastline of Portugal. Gamma radiation measurements were carried out with two different instruments: a sodium iodide scintillation detector counter (SPP2 NF, Saphymo) and a gamma ray spectrometer with energy discrimination (Falcon 5000, Canberra). Two circular survey areas were defined within 20 km of the power plant. Forty relevant measurements points were established within the sampling area: 15 urban and 25 suburban locations. Additionally, ten more measurements points were defined, mostly at the 20-km area. The registered gamma radiation varies from 20 to 98.33 counts per seconds (c.p.s.) corresponding to an external gamma exposure rate variable between 87.70 and 431.19 nGy/h. The highest values were measured at locations near the power plant and those located in an area within the 6 and 20 km from the stacks. In situ gamma radiation measurements with energy discrimination identified natural emitting nuclides as well as their decay products (Pb-212, Pb-2142, Ra-226, Th-232, Ac-228, Th-234, Pa-234, U- 235, etc.). According to the results, an influence from the stacks emissions has been identified both qualitatively and quantitatively. The developed methodology accomplished the lack of data in what concerns to radiation rate in the vicinity of Sines coal-fired power plant and consequently the resulting exposure to the nearby population.

Mechanical performance of concrete made with aggregates from construction and demolition waste recycling plants

This research aims at analysing the mechanical performance of concrete with recycled aggregates (RA) from construction and demolition waste (CDW) from various locations in Portugal. First the characteristics of the various aggregates (natural and recycled) used in the production of concrete were thoroughly analysed. The composition of the RA was determined and several physical and chemical tests of the aggregates were performed. In order to evaluate the mechanical performance of concrete, compressive strength (in cubes and cylinders), splitting tensile strength, modulus of elasticity and abrasion resistance tests were performed. Concrete mixes with RA from CDW from several recycling plants were evaluated, in order to understand the influence that the RA's collection point, and consequently their composition, has on the characteristics of the mixes produced. The analysis of the mechanical performance allowed concluding that the use of RA worsens most of the properties tested, especially when fine RA are used. On the other hand, there was an increase in abrasion resistance when coarse RA were used. In global terms, the use of this type of aggregates, in limited contents, is viable from a mechanical viewpoint. (C) 2015 Elsevier Ltd. All rights reserved.

CardioBengo study protocol: a population based cardiovascular longitudinal study in Bengo Province, Angola

Background: Cardiovascular diseases and other non-communicable diseases are major causes of morbidity and mortality, responsible for 38 million deaths in 2012, 75 % occurring in low- and middle-income countries. Most of these countries are facing a period of epidemiological transition, being confronted with an increased burden of non-communicable diseases, which challenge health systems mainly designed to deal with infectious diseases. With the adoption of the World Health Organization “Global Action Plan for the Prevention and Control of non-communicable diseases, 2013–2020”, the national dimension of risk factors for non-communicable diseases must be reported on a regular basis. Angola has no national surveillance system for non-communicable diseases, and periodic population-based studies can help to overcome this lack of information. CardioBengo will collect information on risk factors, awareness rates and prevalence of symptoms relevant to cardiovascular diseases, to assist decision makers in the implementation of prevention and treatment policies and programs. Methods: CardioBengo is designed as a research structure that comprises a cross-sectional component, providing baseline information and the assembling of a cohort to follow-up the dynamics of cardiovascular diseases risk factors in the catchment area of the Dande Health and Demographic Surveillance System of the Health Research Centre of Angola, in Bengo Province, Angola. The World Health Organization STEPwise approach to surveillance questionnaires and procedures will be used to collect information on a representative sex-age stratified sample, aged between 15 and 64 years old. Discussion: CardioBengo will recruit the first population cohort in Angola designed to evaluate cardiovascular diseases risk factors. Using the structures in place of the Dande Health and Demographic Surveillance System and a reliable methodology that generates comparable results with other regions and countries, this study will constitute a useful tool for the surveillance of cardiovascular diseases. Like all longitudinal studies, a strong concern exists regarding dropouts, but strategies like regular visits to selected participants and a strong community involvement are in place to minimize these occurrences.

The Cristo Rei section (Lower Miocene). Distal fluviatile environments in a marine series, plants, vertebrates and other evidence, age

The section at Cristo Rei shows sandy beds with intercalated clayey lenses (IVb division from the Lisbon Miocene series) that correspond to a major regression event dated from between ca. 17.6 and 17 Ma. They also correspond to a distal position (relatively to the typical fluviatile facies in Lisbon), nearer the basin's axis. Geologic data and paleontological analysis (plant fossils, fishes, crocodilians, land mammals) allow the reconstruction of environments that were represented in the concerned area: estuary with channels and ox-bows; upstream, areas occupied by brackish waters where Gryphaea griphoides banks developped; still farther upstream, freshwaters sided by humid forests and low mountain subtropical forests under warm temperate and rainy conditions, as well as not far away, seasonally dry environments (low density tree or shrub cover, or steppe).

Modelling the Contribution of 40K, 232Th and 226Ra to Radiation Dose and Risk from Airborne Discharges of Coal-Fired Power Plants

Coal contains trace elements and naturally occurring radionuclides such as 40K, 232Th, 238U. When coal is burned, minerals, including most of the radionuclides, do not burn and concentrate in the ash several times in comparison with their content in coal. Usually, a small fraction of the fly ash produced (2-5%) is released into the atmosphere. The activities released depend on many factors (concentration in coal, ash content and inorganic matter of the coal, combustion temperature, ratio between bottom and fly ash, filtering system). Therefore, marked differences should be expected between the by-products produced and the amount of activity discharged (per unit of energy produced) from different coal-fired power plants. In fact, the effects of these releases on the environment due to ground deposition have been received some attention but the results from these studies are not unanimous and cannot be understood as a generic conclusion for all coal-fired power plants. In this study, the dispersion modelling of natural radionuclides was carried out to assess the impact of continuous atmospheric releases from a selected coal plant. The natural radioactivity of the coal and the fly ash were measured and the dispersion was modelled by a Gaussian plume estimating the activity concentration at different heights up to a distance of 20 km in several wind directions. External and internal doses (inhalation and ingestion) and the resulting risk were calculated for the population living within 20 km from the coal plant. In average, the effective dose is lower than the ICRP’s limit and the risk is lower than the U.S. EPA’s limit. Therefore, in this situation, the considered exposure does not pose any risk. However, when considering the dispersion in the prevailing wind direction, these values are significant due to an increase of 232Th and 226Ra concentrations in 75% and 44%, respectively.

Dispersion Modelling of Natural Radionuclides 238U, 232Th and 40K Released from Coal-fired Power Plants Operations

The aim of this work was to simulate the radionuclides dispersion in the surrounding area of a coal-fired power plant, operational during the last 25 years. The dispersion of natural radionuclides (236Ra, 232Th and 40K) was simulated by a Gaussian plume dispersion model with three different stability classes estimating the radionuclides concentration at ground level. Measurements of the environmen-tal activity concentrations were carried out by γ-spectrometry and compared with results from the air dispersion and deposition model which showed that the stabil-ity class D causes the dispersion to longer distances up to 20 km from the stacks.

Behaviour and fate of metals in urban wastewater treatment plants: a review

The concerns on metals in urban wastewater treatment plants (WWTPs) are mainly related to its contents in discharges to environment, namely in the final effluent and in the sludge produced. In the near future, more restrictive limits will be imposed to final effluents, due to the recent guidelines of the European Water Framework Directive (EUWFD). Concerning the sludge, at least seven metals (Cd, Cr, Cu, Hg, Ni, Pb and Zn) have been regulated in different countries, four of which were classified by EUWFD as priority substances and two of which were also classified as hazardous substances. Although WWTPs are not designed to remove metals, the study of metals behaviour in these systems is a crucial issue to develop predictive models that can help more effectively the regulation of pre-treatment requirements and contribute to optimize the systems to get more acceptable metal concentrations in its discharges. Relevant data have been published in the literature in recent decades concerning the occurrence/fate/behaviour of metals in WWTPs. However, the information is dispersed and not standardized in terms of parameters for comparing results. This work provides a critical review on this issue through a careful systematization, in tables and graphs, of the results reported in the literature, which allows its comparison and so its analysis, in order to conclude about the state of the art in this field. A summary of the main consensus, divergences and constraints found, as well as some recommendations, is presented as conclusions, aiming to contribute to a more concerted action of future research. © 2015, Islamic Azad University (IAU).

Performance of concrete made with recycled aggregates from Portuguese CDW recycling plants

The objective of this research is the production of concrete with recycled aggregates (RA) from various CDW plants around Portugal. The influence of the RA collection location and consequently of their composition on the characteristics of the concrete produced was analysed. In the mixes produced in this research RA from five plants (Valnor, Vimajas, Ambilei, Europontal and Retria) were used: in three of them coarse and fine RA were analysed and in the remaining ones only coarse RA were used. The experimental campaign comprised two tests in fresh concrete (cone of Abrams slump and density) and eight in hardened concrete (compressive strength in cubes and cylinders, splitting tensile strength, modulus of elasticity, water absorption by immersion and capillarity, carbonation and chloride penetration resistance). It was found that the use of RA causes a quality decrease in concrete. However, there was a wide results scatter according to the plant where the RAs were collected, because of the variation in composition of the RA. It was also found that the use of fine RA causes a more significant performance loss of the concrete properties analysed than the use of coarse RA. © (2015) Trans Tech Publications, Switzerland.

Intelligent decision support systems for collaboration in industrial plants

Dissertação apresentada para obtenção do Grau de Doutor em Sistemas de Informação Industriais, Engenharia Electrotécnica, pela Universidade Nova de Lisboa, Faculdade de Ciências e Tecnologia

HANTAVIRUS PULMONARY SYNDROME IN THE PROVINCE OF RIO NEGRO, ARGENTINA, 1993-1996

Early in 1995 the first case of Hantavirus Pulmonary Syndrome was serologically confirmed in El Bolsón (Province of Río Negro, Argentina), corresponding to the third outbreak reported in Argentina. A total of 26 cases of HPS related to the Andean region of Rio Negro Province, were reported from 1993 to 1996, 17 in El Bolsón, 4 in San Carlos de Bariloche, and 5 in Buenos Aires. The incidence rate was 5.03 x 100000 with a mortality rate of 51.85 x 100. The occurrence of cases was mainly seasonal, with a significantly greater number in the spring, and the persons affected mainly lived in urban or periurban areas. In four cases, the affected individuals were members of a couple, spouses or live-in contacts. Seven cases were Health workers (physicians, nurses or administrative staff). Twelve cases were related among them, due to an outbreak of 80 days. Two of them did not visit the Andean region. A total of 139 rodents were captured and seven of them, Olygoryzomys longicaudatus, were found to be serologically positive. The possibility of infection by contact with rodents or fecal matter is being analyzed and also hypothesis related with interhuman transmission

Responses of higher plants to boron deficiency

Dissertation presented to obtain the degree of Doctorate in Biochemistry by Instituto de Tecnologia Química e Biológica of Universidade Nova de Lisboa