Energy Efficiency through Thermal Energy Storage : Possibilities for the Swedish Building Stock

The need for heating and cooling in buildings constitutes a considerable part of the total energy use in a country and reducing this need is of outmost importance in order to reach national and international goals for reducing energy use and emissions. One important way of reaching these goals is to increase the proportion of renewable energy used for heating and cooling of buildings. Perhaps the largest obstacle with this is the often occurring mismatch between the availability of renewable energy and the need for heating or cooling, hindering this energy to be used directly. This is one of the problems that can be solved by using thermal energy storage (TES) in order to save the heat or cold from when it is available to when it is needed. This thesis is focusing on the combination of TES techniques and buildings to achieve increased energy efficiency for heating and cooling. Various techniques used for TES as well as the combination of TES in buildings have been investigated and summarized through an extensive literature review. A survey of the Swedish building stock was also performed in order to define building types common in Sweden. Within the scope of this thesis, the survey resulted in the selection of three building types, two single family houses and one office building, out of which the two residential buildings were used in a simulation case study of passive TES with increased thermal mass (both sensible and latent). The second case study presented in the thesis is an evaluation of an existing seasonal borehole storage of solar heat for a residential community. In this case, real measurement data was used in the evaluation and in comparisons with earlier evaluations. The literature reviews showed that using TES opens up potential for reduced energy demand and reduced peak heating and cooling loads as well as possibilities for an increased share of renewable energy to cover the energy demand. By using passive storage through increased thermal mass of a building it is also possible to reduce variations in the indoor temperature and especially reduce excess temperatures during warm periods, which could result in avoiding active cooling in a building that would otherwise need it. The analysis of the combination of TES and building types confirmed that TES has a significant potential for increased energy efficiency in buildings but also highlighted the fact that there is still much research required before some of the technologies can become commercially available. In the simulation case study it was concluded that only a small reduction in heating demand is possible with increased thermal mass, but that the time with indoor temperatures above 24 °C can be reduced by up to 20%. The case study of the borehole storage system showed that although the storage system worked as planned, heat losses in the rest of the system as well as some problems with the system operation resulted in a lower solar fraction than projected. The work presented within this thesis has shown that TES is already used successfully for many building applications (e.g. domestic hot water stores and water tanks for storing solar heat) but that there still is much potential in further use of TES. There are, however, barriers such as a need for more research for some storage technologies as well as storage materials, especially phase change material storage and thermochemical storage.

Modeling and forecasting long-term natural gas (NG) consumption in Iran, using particle swarm optimization (PSO)

The gradual changes in the world development have brought energy issues back into high profile. An ongoing challenge for countries around the world is to balance the development gains against its effects on the environment. The energy management is the key factor of any sustainable development program. All the aspects of development in agriculture, power generation, social welfare and industry in Iran are crucially related to the energy and its revenue. Forecasting end-use natural gas consumption is an important Factor for efficient system operation and a basis for planning decisions. In this thesis, particle swarm optimization (PSO) used to forecast long run natural gas consumption in Iran. Gas consumption data in Iran for the previous 34 years is used to predict the consumption for the coming years. Four linear and nonlinear models proposed and six factors such as Gross Domestic Product (GDP), Population, National Income (NI), Temperature, Consumer Price Index (CPI) and yearly Natural Gas (NG) demand investigated.

Uma perspectiva pós-fordista na operação de sistemas elétricos

O objetivo deste trabalho é mostrar através de um estudo de caso que a implantação de um modelo de organização da produção e do trabalho baseado na gestão por processos pode acenar com uma perspectiva pós-fordista para a atividade de operação de sistemas de energia elétrica. As grandes empresas brasileiras do setor de energia elétrica adotaram, desde a sua criação, um modelo organizacional com base nas funções gerenciais propostas por Henri Fayol, sendo estruturadas de forma vertical e hierárquica. Por outro lado, as tarefas realizadas nas salas de controle dos Centros de Operação dessas empresas se processam de acordo com a forma preconizada pelo sistema de Administração Científica de Frederick Taylor e pelos princípios propostos por Henry Ford. Porém, em decorrência da mudança do modelo institucional do setor de energia, ocorrida em meados da década de 90, além da maior conscientização da sociedade a respeito dos seus direitos de cidadania e também da busca dos trabalhadores pela democratização nas relações sociais em seu ambiente de trabalho, as empresas de energia elétrica foram compelidas a buscar novas formas de gestão mais adequadas ao novo cenário cultural, político, social e econômico. Em FURNAS, como nova forma de organização da produção e do trabalho, o Departamento de Operação do Sistema resolveu adotar um sistema baseado na gestão por processos que respeita a estrutura funcional da Empresa, formando, assim, uma estrutura organizacional matricial. Por outro lado, observou-se que, dependendo da forma de implantação e dos mecanismos de gestão adotados, esse novo sistema podia acenar com uma perspectiva pós-fordista para a atividade de operação de sistemas elétricos de grande porte que, tipicamente, no Brasil, é desenvolvida por empresas fayolistas, segundo uma perspectiva taylorista-fordista. Para verificar se essa possibilidade se concretizou foi realizada uma pesquisa que abrangeu os cinco Centros de Operação do Departamento de Operação do Sistema de FURNAS Centrais Elétricas S.A., tomando como elemento-chave a seguinte caracterização do paradigma do pós-fordismo: diferenciação integrada da organização da produção e do trabalho sob a trajetória de inovação tecnológica em direção à ~ democratização das relações sociais nos sistemas-empresa. O trabalho apresenta a percepção da evolução nos relacionamentos interpessoais e a percepção das ações gerenciais empreendidas visando a implantação do novo sistema, bem como também mostra as transformações ocorridas no tocante à democratização das relaçõe~ sociais no Departamento, entre outros fatores que substanciam a pesquisa, cujo resultado aponta para uma nova forma de gestão do trabalho e da produção em que essas relações sociais tendem a ser pautadas por ações gerenciais dialógicas que caracterizam a perspectiva pós-fordista.

Dedução de Funções de Alívio para Priorização de Variantes de Chaveamento Adequadas à Eliminação de Sobrecargas

Eventually, violations of voltage limits at buses or admissible loadings of transmission lines and/or power transformers may occur by the power system operation. If violations are detected in the supervision process, corrective measures may be carried out in order to eliminate them or to reduce their intensity. Loading restriction is an extreme solution and should only be adopted as the last control action. Previous researches have shown that it is possible to control constraints in electrical systems by changing the network topology, using the technique named Corrective Switching, which requires no additional costs. In previous works, the proposed calculations for verifying the ability of a switching variant in eliminating an overload in a specific branch were based on network reduction or heuristic analysis. The purpose of this work is to develop analytical derivation of linear equations to estimate current changes in a specific branch (due to switching measures) by means of few calculations. For bus-bar coupling, derivations will be based on short-circuit theory and Relief Function methodology. For bus-bar splitting, a Relief Function will be derived based on a technique of equivalent circuit. Although systems of linear equations are used to substantiate deductions, its formal solution for each variant, in real time does not become necessary. A priority list of promising variants is then assigned for final check by an exact load flow calculation and a transient analysis using ATP Alternative Transient Program. At last, results obtained by simulation in networks with different features will be presented

Um algoritmo para estimação de estado em alimentadores de distribuição de energia elétrica com base no método da soma de potências

Most algorithms for state estimation based on the classical model are just adequate for use in transmission networks. Few algorithms were developed specifically for distribution systems, probably because of the little amount of data available in real time. Most overhead feeders possess just current and voltage measurements at the middle voltage bus-bar at the substation. In this way, classical algorithms are of difficult implementation, even considering off-line acquired data as pseudo-measurements. However, the necessity of automating the operation of distribution networks, mainly in regard to the selectivity of protection systems, as well to implement possibilities of load transfer maneuvers, is changing the network planning policy. In this way, some equipments incorporating telemetry and command modules have been installed in order to improve operational features, and so increasing the amount of measurement data available in real-time in the System Operation Center (SOC). This encourages the development of a state estimator model, involving real-time information and pseudo-measurements of loads, that are built from typical power factors and utilization factors (demand factors) of distribution transformers. This work reports about the development of a new state estimation method, specific for radial distribution systems. The main algorithm of the method is based on the power summation load flow. The estimation is carried out piecewise, section by section of the feeder, going from the substation to the terminal nodes. For each section, a measurement model is built, resulting in a nonlinear overdetermined equations set, whose solution is achieved by the Gaussian normal equation. The estimated variables of a section are used as pseudo-measurements for the next section. In general, a measurement set for a generic section consists of pseudo-measurements of power flows and nodal voltages obtained from the previous section or measurements in real-time, if they exist -, besides pseudomeasurements of injected powers for the power summations, whose functions are the load flow equations, assuming that the network can be represented by its single-phase equivalent. The great advantage of the algorithm is its simplicity and low computational effort. Moreover, the algorithm is very efficient, in regard to the accuracy of the estimated values. Besides the power summation state estimator, this work shows how other algorithms could be adapted to provide state estimation of middle voltage substations and networks, namely Schweppes method and an algorithm based on current proportionality, that is usually adopted for network planning tasks. Both estimators were implemented not only as alternatives for the proposed method, but also looking for getting results that give support for its validation. Once in most cases no power measurement is performed at beginning of the feeder and this is required for implementing the power summation estimations method, a new algorithm for estimating the network variables at the middle voltage bus-bar was also developed

Remoção biológica de nitrato em água de abastecimento humano utilizando o endocarpo de coco como fonte de carbono

The groundwater quality has been compromised as a result of the intensification of human activities over the years. Groundwater contamination by nitrate is one of the effects of this degradation, a socio-environmental problem that affects many regions of the world and particular the city of Natal (RN). Developing techniques for nitrate removal in water is intended to eliminate or reduce the concentration of this compound, and those that involve biological processes have produced economic and environmental advantages. This study proposes a technology for biological removal of nitrate in water supply for humans, using the endocarp s coconut as a carbon source and bacteria support. The experiments were performed in pilot scale anoxic, testing different areas of the substrate surface. Results showed high rates nitrate removal during the monitoring period, noting the occurrence of denitrification after the beginning of system operation. The best performance was achieved in the treatment system containing substrate surface area increased, indicating that the decrease in the endocarp size contributed to increased bacterial activity, improving the ability to remove nitrate. About the quality analyzed aspects of water, it was found that the proposed technology has the potential water use for human consumption

Stochastic stability for Markovian jump linear systems associated with a finite number of jump times

This paper deals with a stochastic stability concept for discrete-time Markovian jump linear systems. The random jump parameter is associated to changes between the system operation modes due to failures or repairs, which can be well described by an underlying finite-state Markov chain. In the model studied, a fixed number of failures or repairs is allowed, after which, the system is brought to a halt for maintenance or for replacement. The usual concepts of stochastic stability are related to pure infinite horizon problems, and are not appropriate in this scenario. A new stability concept is introduced, named stochastic tau-stability that is tailored to the present setting. Necessary and sufficient conditions to ensure the stochastic tau-stability are provided, and the almost sure stability concept associated with this class of processes is also addressed. The paper also develops equivalences among second order concepts that parallels the results for infinite horizon problems. (C) 2003 Elsevier B.V. All rights reserved.

Sistema de tração elétrica flexível baseado em veículos trólebus para alimentação com redes CC e ou CA

Este artigo apresenta os principais resultados e o detalhamento da metodologia e equações de controle de um retificador monofásico pré-regulador de 150kW para sistema trólebus. A estrutura proposta possibilita a Correção ativa do Fator de Potência (CFP) com baixos níveis de Distorção Harmônica Total (DHT) na corrente, em conformidade com a norma internacional IEC 61000-3-4. Fruto de um projeto de Pesquisa, Desenvolvimento e Inovação (P) junto à empresa AES Eletropaulo Metropolitana de São Paulo, em parceria com a empresa de transporte Himalaia S.A., o projeto possui como principais objetivos estimular o interesse para a expansão das linhas de trólebus a partir de uma plataforma de alimentação de menor custo de instalação e manutenção, sem a necessidade de subestações retificadoras, e, com vistas a promover a melhoria da qualidade de vida nos grandes centros urbanos. Nessa nova modalidade proposta para o sistema de alimentação, o trólebus pode ser alimentado tanto pelas redes convencionais em corrente contínua (CC) quanto pelas redes de distribuição em corrente alternada (CA), mantendo-se a disposição a dois fios dos sistemas CC, sendo as mudanças de rede de alimentação (CC ou CA) monitoradas e controladas digitalmente. Todo o sistema de gerenciamento e controle do conversor é realizado digitalmente por FPGA XC3S200. Na evolução do sistema proposto, os autores pretendem inclusive eliminar as linhas aéreas de alimentação, através da utilização de postos de alimentação em CA, especialmente desenvolvidos para os pontos de embarque/desembarque de passageiros para este veículo de transporte coletivo, eliminando-se os aspectos visuais negativos das redes de alimentação deste modal, e, reduzindo-se as falhas de operação do sistema.

Uma abordagem baseada em aspectos e composição dinâmica para a construção de aplicações adaptativas cientes ao contexto

Ubiquitous computing systems operate in environments where the available resources significantly change during the system operation, thus requiring adaptive and context aware mechanisms to sense changes in the environment and adapt to new execution contexts. Motivated by this requirement, a framework for developing and executing adaptive context aware applications is proposed. The PACCA framework employs aspect-oriented techniques to modularize the adaptive behavior and to keep apart the application logic from this behavior. PACCA uses abstract aspect concept to provide flexibility by addition of new adaptive concerns that extend the abstract aspect. Furthermore, PACCA has a default aspect model that considers habitual adaptive concerns in ubiquitous applications. It exploits the synergy between aspect-orientation and dynamic composition to achieve context-aware adaptation, guided by predefined policies and aim to allow software modules on demand load making possible better use of mobile devices and yours limited resources. A Development Process for the ubiquitous applications conception is also proposed and presents a set of activities that guide adaptive context-aware developer. Finally, a quantitative study evaluates the approach based on aspects and dynamic composition for the construction of ubiquitous applications based in metrics

Organização do sistema de referência e contra-referência no contexto do Sistema Único de Saúde: a percepção de enfermeiro

Este estudo teve como objetivo compreender e desvelar a percepção de enfermeiros sobre o sistema de referência e contra-referência, no contexto do Sistema Único de Saúde do município de Botucatu ISP/BR, a partir da experiência vivenciada na prática. Para tanto, optamos pela pesquisa qualitativa, na modalidade do fenômeno situado, vertente metodológica da fenomenologia. Num primeiro momento, buscamos realizar uma revisão histórica sobre o processo de construção do Sistema Único de Saúde no Brasil e o significado do sistema de referência e contra-referência neste contexto. A construção dos resultados foi realizada a partir das análises ideográfica e nomotética dos depoimentos de treze enfermeiras, tendo emergido destes treze temas, posteriormente agrupados em três categorias principais: o funcionamento do sistema de referência e contra-referência, as possibilidades de encaminhamento da clientela e fatores estruturais do sistema local, desvelando que a referência e contra-referência ainda não passa de um horizonte e só funciona quando há empenho pessoal dos profissionais isoladamente.

The LQ control problem for Markovian jumps linear systems with horizon defined by stopping times

This paper deals with a stochastic optimal control problem involving discrete-time jump Markov linear systems. The jumps or changes between the system operation modes evolve according to an underlying Markov chain. In the model studied, the problem horizon is defined by a stopping time τ which represents either, the occurrence of a fix number N of failures or repairs (TN), or the occurrence of a crucial failure event (τΔ), after which the system is brought to a halt for maintenance. In addition, an intermediary mixed case for which T represents the minimum between TN and τΔ is also considered. These stopping times coincide with some of the jump times of the Markov state and the information available allows the reconfiguration of the control action at each jump time, in the form of a linear feedback gain. The solution for the linear quadratic problem with complete Markov state observation is presented. The solution is given in terms of recursions of a set of algebraic Riccati equations (ARE) or a coupled set of algebraic Riccati equation (CARE).

Transmission network expansion planning in full open market considering security constraints

This paper presents a mathematical model and a methodology to solve the transmission network expansion planning problem with security constraints in full competitive market, assuming that all generation programming plans present in the system operation are known. The methodology let us find an optimal transmission network expansion plan that allows the power system to operate adequately in each one of the generation programming plans specified in the full competitive market case, including a single contingency situation with generation rescheduling using the security (n-1) criterion. In this context, the centralized expansion planning with security constraints and the expansion planning in full competitive market are subsets of the proposal presented in this paper. The model provides a solution using a genetic algorithm designed to efficiently solve the reliable expansion planning in full competitive market. The results obtained for several known systems from the literature show the excellent performance of the proposed methodology.

Intelligent alarm processing

This paper presents the analysis that have been carried out in the alarm system of the DCRanger EMS. The intention of this study is to present the problem of alarm processing in electric energy control centers, its various aspects and operational difficulties due to operator needs. Some tests are produced in order to identify the desirable features an alarm system should possess in order to be of effective help in the operative duty. © 2006 IEEE.

Reconfiguração de alimentadores em sistemas de distribuição usando a metaheurística GRASP

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Fluxo de carga não-iterativo para a análise de sistemas de distribuição de energia elétrica radiais e malhados

Pós-graduação em Engenharia Elétrica - FEIS