Microbial communities in Pb contaminated boreal forest soil

Lead contamination in the environment is of particular concern, as it is a known toxin. Until recently, however, much less attention has been given to the local contamination caused by activities at shooting ranges compared to large-scale industrial contamination. In Finland, more than 500 tons of Pb is produced each year for shotgun ammunition. The contaminant threatens various organisms, ground water and the health of human populations. However, the forest at shooting ranges usually shows no visible sign of stress compared to nearby clean environments. The aboveground biota normally reflects the belowground ecosystem. Thus, the soil microbial communities appear to bear strong resistance to contamination, despite the influence of lead. The studies forming this thesis investigated a shooting range site at Hälvälä in Southern Finland, which is heavily contaminated by lead pellets. Previously it was experimentally shown that the growth of grasses and degradation of litter are retarded. Measurements of acute toxicity of the contaminated soil or soil extracts gave conflicting results, as enchytraeid worms used as toxicity reporters were strongly affected, while reporter bacteria showed no or very minor decreases in viability. Measurements using sensitive inducible luminescent reporter bacteria suggested that the bioavailability of lead in the soil is indeed low, and this notion was supported by the very low water extractability of the lead. Nevertheless, the frequency of lead-resistant cultivable bacteria was elevated based on the isolation of cultivable strains. The bacterial and fungal diversity in heavily lead contaminated shooting sectors were compared with those of pristine sections of the shooting range area. The bacterial 16S rRNA gene and fungal ITS rRNA gene were amplified, cloned and sequenced using total DNA extracted from the soil humus layer as the template. Altogether, 917 sequenced bacterial clones and 649 sequenced fungal clones revealed a high soil microbial diversity. No effect of lead contamination was found on bacterial richness or diversity, while fungal richness and diversity significantly differed between lead contaminated and clean control areas. However, even in the case of fungi, genera that were deemed sensitive were not totally absent from the contaminated area: only their relative frequency was significantly reduced. Some operational taxonomic units (OTUs) assigned to Basidiomycota were clearly affected, and were much rarer in the lead contaminated areas. The studies of this thesis surveyed EcM sporocarps, analyzed morphotyped EcM root tips by direct sequencing, and 454-pyrosequenced fungal communities in in-growth bags. A total of 32 EcM fungi that formed conspicuous sporocarps, 27 EcM fungal OTUs from 294 root tips, and 116 EcM fungal OTUs from a total of 8 194 ITS2 454 sequences were recorded. The ordination analyses by non-parametric multidimensional scaling (NMS) indicated that Pb enrichment induced a shift in the EcM community composition. This was visible as indicative trends in the sporocarp and root tip datasets, but explicitly clear in the communities observed in the in-growth bags. The compositional shift in the EcM community was mainly attributable to an increase in the frequencies of OTUs assigned to the genus Thelephora, and to a decrease in the OTUs assigned to Pseudotomentella, Suillus and Tylospora in Pb-contaminated areas when compared to the control. The enrichment of Thelephora in contaminated areas was also observed when examining the total fungal communities in soil using DNA cloning and sequencing technology. While the compositional shifts are clear, their functional consequences for the dominant trees or soil ecosystem remain undetermined. The results indicate that at the Hälvälä shooting range, lead influences the fungal communities but not the bacterial communities. The forest ecosystem shows apparent functional redundancy, since no significant effects were seen on forest trees. Recently, by means of 454 pyrosequencing , the amount of sequences in a single analysis run can be up to one million. It has been applied in microbial ecology studies to characterize microbial communities. The handling of sequence data with traditional programs is becoming difficult and exceedingly time consuming, and novel tools are needed to handle the vast amounts of data being generated. The field of microbial ecology has recently benefited from the availability of a number of tools for describing and comparing microbial communities using robust statistical methods. However, although these programs provide methods for rapid calculation, it has become necessary to make them more amenable to larger datasets and numbers of samples from pyrosequencing. As part of this thesis, a new program was developed, MuSSA (Multi-Sample Sequence Analyser), to handle sequence data from novel high-throughput sequencing approaches in microbial community analyses. The greatest advantage of the program is that large volumes of sequence data can be manipulated, and general OTU series with a frequency value can be calculated among a large number of samples.

Prey of the silver-headed antechinus (Antechinus argentus), a new species of Australian dasyurid marsupial

The silver-headed antechinus (Antechinus argentus) is one of Australia’s most recently described mammals, and the single known population at Kroombit Tops in south-east Queensland is threatened. Nothing is known of the species’ ecology, so during 2014 we collected faecal pellets each month (March–September) from a population at the type locality to gather baseline data on diet composition. A total of 38 faecal pellets were collected from 12 individuals (eight females, four males) and microscopic analysis of pellets identified seven invertebrate orders, with 70% combined mean composition of beetles (Coleoptera: 38%) and cockroaches (Blattodea: 32%). Other orders that featured as prey were ants, crickets/grasshoppers, butterflies/moths, spiders, and true bugs. Given that faecal pellets could only be collected from a single habitat type (Eucalyptus montivaga high-altitude open forest) and location, this is best described as a generalist insectivorous diet that is characteristic of other previously studied congeners.

Electrochemical properties and intermediate-temperature fuel cell performance of dense yttrium-doped barium zirconate with calcium addition

Although BaZr 0.8Y 0.2O 3-δ(BZY) possesses large bulk proton conductivity and excellent chemical stability, its poor sinterability and grain boundaries block proton conduction. In this work, the effect of Ca as a co-dopant and as a sintering aid (as CaO), on the sinterability, proton conductivity, and fuel cell performance of BZY was investigated. The addition of 4 mol% CaO significantly improved the BZY sinterability: BZY pellets with densities of 92.7% and 97.5% with respect to the theoretical density were obtained after sintering at 1500°C and 1600°C, respectively. The improved BZY sinterability by CaO addition resulted also in a large proton conductivity; at 600°C, the total conductivity of BZY-CaO was 2.14 × 10 -3 S/cm, in wet Ar. Anode-supported fuel cells with 25 μm-thick BZY-CaO electrolyte membranes were fabricated by a dual-layer co-firing technique. The peak power density of the fuel cell with a BZY-Ni/BZY-4CaO/BZY-LSCF (La 0.6Sr 0.4Fe 0.8Co 0.2O 3-δ) configuration was 141 mW/cm 2 at 700°C, several times larger than the reported values of BZY electrolyte membrane fuel cells sintered with the addition of CuO or ZnO, demonstrating promising features for practical fuel cell applications.

Lowering grain boundary resistance of BaZr0.8Y0.2O3−δ with LiNO3 sintering-aid improves proton conductivity for fuel cell operation

A novel sintering additive based on LiNO3 was used to overcome the drawbacks of poor sinterability and low grain boundary conductivity in BaZr0.8Y0.2O3-δ (BZY20) protonic conductors. The Li-additive totally evaporated during the sintering process at 1600°C for 6 h, which led to highly dense BZY20 pellets (96.5% of the theoretical value). The proton conductivity values of BZY20 with Li sintering-aid were significantly larger than the values reported for BZY sintered with other metal oxides, due to the fast proton transport in the "clean" grain boundaries and grain interior. The total conductivity of BZY20-Li in wet Ar was 4.45 × 10-3 S cm-1 at 600°C. Based on the improved sinterability, anode-supported fuel cells with 25 μm-thick BZY20-Li electrolyte membranes were fabricated by a co-firing technique. The peak power density obtained at 700°C for a BZY-Ni/BZY20-Li/La0.6Sr0.4Co0.2Fe 0.8O3-δ (LSCF)-BZY cell was 53 mW cm-2, which is significantly larger than the values reported for fuel cells using electrolytes made of BZY sintered with the addition of ZnO and CuO, confirming the advantage of using Li as a sintering aid.

Sinteractivity, proton conductivity and chemical stability of BaZr 0.7In0.3O3-δ for solid oxide fuel cells (SOFCs)

In3+ was used as dopant for BaZrO3 proton conductor and 30 at%-doped BaZrO3 samples (BaZr0.7In 0.3O3-δ, BZI) were prepared as electrolyte materials for proton-conducting solid oxide fuel cells (SOFCs). The BZI material showed a much improved sinteractivity compared with the conventional Y-doped BaZrO 3. The BZI pellets reached almost full density after sintering at 1600 °C for 10 h, whereas the Y-doped BaZrO3 samples still remained porous under the same sintering conditions. The conductivity measurements indicated that BZI pellets showed smaller bulk but improved grain boundary proton conductivity, when compared with Y-doped BaZrO3 samples. A total proton conductivity of 1.7 × 10-3 S cm -1 was obtained for the BZI sample at 700 °C in wet 10% H 2 atmosphere. The BZI electrolyte material also showed adequate chemical stability against CO2 and H2O, which is promising for application in fuel cells.

Gasifier stoves - science, technology and field outreach

Development of a new class of single pan high efficiency, low emission stoves, named gasifier stoves, that promise constant power that can be controlled using any solid biomass fuel in the form of pellets is reported here. These stoves use battery-run fan-based air supply for gasification (primary air) and for combustion (secondary air).Design with the correct secondary air flow ensures near-stoichiometric combustion that allows attainment of peak combustion temperatures with accompanying high water boiling efficiencies (up to 50% for vessels of practical relevance) and very low emissions (of carbon monoxide, particulate matter and oxides of nitrogen). The use of high density agro-residue based pellets or coconut shell pieces ensures operational duration of about an hour or more at power levels of 3 kWth (similar to 12 g/min). The principles involved and the optimization aspects of the design are outlined. The dependence of efficiency and emissions on the design parameters are described. The field imperatives that drive the choice of the rechargeable battery source and the fan are brought out. The implications of developments of Oorja-Plus and OorjaSuper stoves to the domestic cooking scenario of India are briefly discussed. The process development, testing and internal qualification tasks were undertaken by Indian Institute of Science. Product development and the fuel pellet production were dealt with by First Energy Private Ltd.Close interaction at several times during this period has helped progress the project from the laboratory to large scale commercial operation. At this time, over four hundred thousand stoves and 30 kilotonnes fuel have been sold in four states in India.

Dielectric relaxation and electrical conductivity in Bi5NbO10 oxygen ion conductors prepared by a modified sol–gel process

Crystalline Bi5NbO10 nanoparticles have been achieved through a modified sol–gel process using a mixture of ethylenediamine and ethanolamine as a solvent. The Bi5NbO10 nanoparticles were characterized by X-ray diffraction (XRD), differential scanning calorimetry/thermogravimetry (DSC/TG), Fourier transform infrared spectroscopy (FT-IR), transmission electron microscopy (TEM) and Raman spectroscopy. The results showed that well-dispersed 5–60 nm Bi5NbO10 nanoparticles were prepared through heat-treating the precursor at 650 °C and the high density pellets were obtained at temperatures lower than those commonly employed. The frequency and temperature dependence of the dielectric constant and the electrical conductivity of the Bi5NbO10 solid solutions were investigated in the 0.1 Hz to 1 MHz frequency range. Two distinct relaxation mechanisms were observed in the plots of dielectric loss and the imaginary part of impedance (Z″) versus frequency in the temperature range of 200–350 °C. The dielectric constant and the loss in the low frequency regime were electrode dependent. The ionic conductivity of Bi5NbO10 solid solutions at 700 °C is 2.86 Ω−1 m−1 which is in same order of magnitude for Y2O3-stabilized ZrO2 ceramics at same temperature. These results suggest that Bi5NbO10 is a promising material for an oxygen ion conductor.

Certain novel features of the R.F. response of the YBa2Cu3O7−x superconductors

The r.f. absorption experiment performed on YBa2Cu3O7-x ceramic pellets using a CW NMR spectrometer shows some novel observed in the microwave range.

Laser processing of high-Tc superconducting thin films

High-Tc superconducting thin films can be deposited and processed by pulsed and CW lasers, and a respectable materials technology for the Y-Ba-Cu-O superconductor is rapidly emerging. The pulsed laser deposition technique is simple because it produces films with compositions nearly identical to those of the target pellets. A larger variety of substrates can be used, compared to other deposition technologies, because of the relatively low temperature requirements. The laser deposition mechanism has been investigated. As-deposited superconducting films, epitaxial films with smooth surfaces, and multilayer structures with abrupt interfaces have been produced. The electrical transport properties can be changed locally using a focused argon-ion laser by modifying the oxygen stoichiometry. This laser writing can be erased by room-temperature exposure to an oxygen plasma. Other laser patterning methods such as material removal, melt-quench, and direct pattern transfer are being developed.

A simple apparatus for the measurement of thermoelectric power in the temperature range 4·2–300K

A simple apparatus to measure the absolute thermoelectric power of solids in the temperature range 4·2–300K is described. The cryostat and the associated instrumentation is simple to operate. Representative data of measurements on metallic wire and pressed pellets are given. An accuracy of better than 10% in absolute thermopower can be obtained in this apparatus.

Jauheiden erottuminen

Partikkelisysteemien segregaatio eli erottuminen on ilmiö, jossa tasalaatuisen jauheseoksen komponenteilla on taipumus erota toisistaan. Jauheen erottumistaipumus riippuu partikkelien ominaisuuksista, ympäröivistä olosuhteista ja partikkelien välisistä vuorovaikutuksista. Segregaatiomekanismeja on esitetty kirjallisuudessa valtava määrä ja pienetkin erot partikkelien välisissä ominaisuuksissa ja vuorovaikutuksissa voivat johtaa täysin eri segregaatiomekanismeihin. Segregaatioilmiö on lääketeollisuuden näkökulmasta hyvin keskeinen, eikä sitä tunneta vielä riittävän hyvin, jotta siltä osattaisiin systemaattisesti välttyä. Nykyinen segregaatiotutkimus perustuu suurelta osin yrityksen ja erehdyksen kautta tapahtuvaan oppimiseen. Todellisen segregaatioilmiön ymmärtämiseen tarvittaisiin innovatiivisia tutkimusmenetelmiä. Kokeellisen osan tarkoituksena oli kehittää ja perustestata menetelmä, jolla voidaan tutkia erilaisten partikkelisysteemien erottumiskäyttäytymistä, ja käyttää tätä menetelmää farmaseuttisten rae- ja pellettiseosten segregaation tutkimiseen. Tavoitteena oli todistaa kehitetyn Babel-laitteen toimintaperiaatteen soveltuvuus partikkelisysteemien erottumiskäyttäytymisen tutkimiseen, mutta suoritetut kokeet olivat lähinnä menetelmän ja laitteen testausta. Ongelmiksi muodostuivat Babel-laitteen asettamat rajoitukset, partikkelien sähköistyminen ja partikkelien väliset vuorovaikutukset. Käytetyt suoraviivaiset lähestymistavat eivät riittäneet segregaation aiheuttamiseen Babel-laitteella. Vertikaalisen ravistelun seurauksena syntynyt konvektiopyörre esti segregaation syntymisen. Johtopäätöksenä voidaan sanoa, että Babel-laite mittaa hyvin ja toistettavasti sekä se kykenee erottamaan erikokoiset partikkelit ja erilaiset kokojakaumat toisistaan. Laitteen kehittämistavoitteena olisi saada segregaatio paremmin näkyviin jauheseoksissa ravistelun seurauksena. Tällöin voitaisiin tehdä päätelmiä jauheseoksen erottumistaipumuksesta ja systeemissä vallitsevista erottumismekanismeista. Laitteen ja menetelmän jatkokehittäminen voisi tuottaa hyödyllistä lisätietoa, mikä edesauttaisi segregaation ymmärtämistä ilmiönä entistä paremmin

Laser-fused refractory oxides for optical coatings

Laser sintering was carried out using a high power continuous-wave CO2 laser to prepare pellets of zirconia (ZrO2), hafnia (HfO2) and yttria (Y2O3) mixed oxides as starting materials in the deposition of optical coatings. Hardened recrystallized pellets appeared to have been formed during laser treatment. X-ray diffraction analysis revealed a monoclinic-to-tetragonal phase transformation in the binary system while the ternary system was found to have a mixture of two crystalline phases. Cross-sectional scanning electron microscopy showed two isothermal crystalline regions in the ternary system. The optical inhomogeneity was low in the films deposited from the laser-fused pellets, but the absorption at a wavelength of 351 nm increased with increasing HfO2 content. The films deposited from laser-fused pellets were analysed by electron spectroscopy for chemical analysis and found to be stoichiometric and homogeneous.

Behavior of Ca(OH)2/CaO pellet under dehydration and hydration

With construction of a thermochemical energy conversion prototype system to store solar heat, thermal dissociation of pellets of Ca(OH)2 and hydration of CaO have been investigated in some detail for its application to the system. The inorganic substance is very attractive as a material for long term heat storage, but molar density changes associated with the reaction are fairly large. Therefore, this factor has been taken into account in the kinetic equation. The importance of additives and pellet size has been discussed considering reactivity and strength of pellets. An analysis has been attempted when chemical reaction is important. The deformation of pellets was observed during hydration.

Investigations of carbon nanotubes

Experiments have been carried out to optimize the yields of carbon nanotubes obtained by the arc-evaporation of graphite. Other types of carbon particles such as nanocrystalline graphite usually present along with the nanotubes are readily removed by heating the material in oxygen around 763 K. Clean nanotubes so obtained have been characterized by X-ray diffraction. The clean tubes are thermally more stable than graphite or fullerenes. The tips of carbon nanotubes are opened by reaction with oxygen, but more interestingly, when the oxygen produced by the decomposition of a metal oxide is used to open the tube tips, the metal formed in the process enters the nanotube. Electrical resistance of pressed pellets of clean tubes is not unlike that of graphite. Tunnelling conductance measurements on isolated tubes characterized by means of scanning tunnelling microscopy however show that the conductance gap increases with decreasing tube diameter.

Phase evolution and densification of spray pyrolysed ZrO2-Al2O3 powders

Devitrification of spray pyrolysed, amorphous ZrO2-Al2O3 solid solution produces nanocrystalline microstructures (grain sizes 10-20 nm). In this study, spray pyrolysed amorphous ZrO2-40 mol% Al2O3 powder displayed good sinterability during decomposition, after spraying, of the nitrate precursors up to 1023K. Hot pressing of fully pyrolysed, pre-sintered (more than 70% dense) pellets at 923K and 750 MPa produced an amorphous pellet with less than 2% porosity. The results indicate the possibility of producing dense, amorphous pellets that can be heat treated further to produce nanocrystalline microstructures conducive for superplasticity.