Modelagem matemática para o transporte de partículas sujeitas a múltiplos mecanismos de retenção

Discrepancies between classical model predictions and experimental data for deep bed filtration have been reported by various authors. In order to understand these discrepancies, an analytic continuum model for deep bed filtration is proposed. In this model, a filter coefficient is attributed to each distinct retention mechanism (straining, diffusion, gravity interception, etc.). It was shown that these coefficients generally cannot be merged into an effective filter coefficient, as considered in the classical model. Furthermore, the derived analytic solutions for the proposed model were applied for fitting experimental data, and a very good agreement between experimental data and proposed model predictions were obtained. Comparison of the obtained results with empirical correlations allowed identifying the dominant retention mechanisms. In addition, it was shown that the larger the ratio of particle to pore sizes, the more intensive the straining mechanism and the larger the discrepancies between experimental data and classical model predictions. The classical model and proposed model were compared via statistical analysis. The obtained p values allow concluding that the proposed model should be preferred especially when straining plays an important role. In addition, deep bed filtration with finite retention capacity was studied. This work also involves the study of filtration of particles through porous media with a finite capacity of filtration. It was observed, in this case, that is necessary to consider changes in the boundary conditions through time evolution. It was obtained a solution for such a model using different functions of filtration coefficients. Besides that, it was shown how to build a solution for any filtration coefficient. It was seen that, even considering the same filtration coefficient, the classic model and the one here propposed, show different predictions for the concentration of particles retained in the porous media and for the suspended particles at the exit of the media

Estratégias de aplicações sequenciais e paralelas da metaheurística otimização por enxame de partículas ao problema do caixeiro viajante

Particle Swarm Optimization is a metaheuristic that arose in order to simulate the behavior of a number of birds in flight, with its random movement locally, but globally determined. This technique has been widely used to address non-liner continuous problems and yet little explored in discrete problems. This paper presents the operation of this metaheuristic, and propose strategies for implementation of optimization discret problems as form of execution parallel as sequential. The computational experiments were performed to instances of the TSP, selected in the library TSPLIB contenct to 3038 nodes, showing the improvement of performance of parallel methods for their sequential versions, in executation time and results

Maximização da penetração da geração distribuída através do algoritmo de otimização nuvem de partículas

This work develops a methodology for defining the maximum active power being injected into predefined nodes in the studied distribution networks, considering the possibility of multiple accesses of generating units. The definition of these maximum values is obtained from an optimization study, in which further losses should not exceed those of the base case, i.e., without the presence of distributed generation. The restrictions on the loading of the branches and voltages of the system are respected. To face the problem it is proposed an algorithm, which is based on the numerical method called particle swarm optimization, applied to the study of AC conventional load flow and optimal load flow for maximizing the penetration of distributed generation. Alternatively, the Newton-Raphson method was incorporated to resolution of the load flow. The computer program is performed with the SCILAB software. The proposed algorithm is tested with the data from the IEEE network with 14 nodes and from another network, this one from the Rio Grande do Norte State, at a high voltage (69 kV), with 25 nodes. The algorithm defines allowed values of nominal active power of distributed generation, in percentage terms relative to the demand of the network, from reference values

Análise do efeito do tempo da moagem de alta energia no tamanho de cristalito e microdeformação da rede cristalina do WC-Co

Hard metals are the composite developed in 1923 by Karl Schröter, with wide application because high hardness, wear resistance and toughness. It is compound by a brittle phase WC and a ductile phase Co. Mechanical properties of hardmetals are strongly dependent on the microstructure of the WC Co, and additionally affected by the microstructure of WC powders before sintering. An important feature is that the toughness and the hardness increase simultaneously with the refining of WC. Therefore, development of nanostructured WC Co hardmetal has been extensively studied. There are many methods to manufacture WC-Co hard metals, including spraying conversion process, co-precipitation, displacement reaction process, mechanochemical synthesis and high energy ball milling. High energy ball milling is a simple and efficient way of manufacturing the fine powder with nanostructure. In this process, the continuous impacts on the powders promote pronounced changes and the brittle phase is refined until nanometric scale, bring into ductile matrix, and this ductile phase is deformed, re-welded and hardened. The goal of this work was investigate the effects of highenergy milling time in the micro structural changes in the WC-Co particulate composite, particularly in the refinement of the crystallite size and lattice strain. The starting powders were WC (average particle size D50 0.87 μm) supplied by Wolfram, Berglau-u. Hutten - GMBH and Co (average particle size D50 0.93 μm) supplied by H.C.Starck. Mixing 90% WC and 10% Co in planetary ball milling at 2, 10, 20, 50, 70, 100 and 150 hours, BPR 15:1, 400 rpm. The starting powders and the milled particulate composite samples were characterized by X-ray Diffraction (XRD) and Scanning Electron Microscopy (SEM) to identify phases and morphology. The crystallite size and lattice strain were measured by Rietveld s method. This procedure allowed obtaining more precise information about the influence of each one in the microstructure. The results show that high energy milling is efficient manufacturing process of WC-Co composite, and the milling time have great influence in the microstructure of the final particles, crushing and dispersing the finely WC nanometric order in the Co particles

Desgaste de polímeros estruturais de engenharia em contato de deslizamento com cilindro metálico

Present work proposed to map and features the wear mechanisms of structural polymers of engineering derived of the sliding contact with a metallic cylindrical spindle submitted to eccentricity due to fluctuations in it is mass and geometric centers. For this it was projected and makes an experimental apparatus from balancing machine where the cylindrical counterbody was supported in two bearings and the polymeric coupon was situated in a holder with freedom of displacement along counterbody. Thus, the experimental tests were standardized using two position of the two bearings (Fixed or Free) and seven different positions along the counterbody, that permit print different conditions to the stiffness from system. Others parameters as applied normal load, sliding velocity and distance were fixed. In this investigation it was used as coupon two structural polymers of wide quotidian use, PTFE (polytetrafluroethylene) and PEEK (poly-ether-ether-ketone) and the AISI 4140 alloy steel as counterbody. Polymeric materials were characterized by thermal analysis (thermogravimetric, differential scanning calorimetry and dynamic-mechanical), hardness and rays-X diffractometry. While the metallic material was submitted at hardness, mechanical resistance tests and metallographic analysis. During the tribological tests were recorded the heating response with thermometers, yonder overall velocity vibration (VGV) and the acceleration using accelerometers. After tests the wear surface of the coupons were analyzed using a Scanning Electronic Microscopy (SEM) to morphological analysis and spectroscopy EDS to microanalysis. Moreover the roughness of the counterbody was characterized before and after the tribological tests. It was observed that the tribological response of the polymers were different in function of their distinct molecular structure. It were identified the predominant wear mechanisms in each polymer. The VGV of the PTFE was smaller than PEEK, in the condition of minimum stiffness, in function of the higher loss coefficient of that polymer. Wear rate of the PTFE was more of a magnitude order higher than PEEK. With the results was possible developed a correlation between the wear rate and parameter (E/ρ)1/2 (Young modulus, E, density, ρ), proportional at longitudinal elastic wave velocity in the material.

Mecanismos de desgaste, história térmica e ciclo de vida de componentes de um motor de combustão interna de aeromodelo

We developed an assay methodology that considered the temperature variation and the scanning electron microscopy as a method to quantify and characterize respectively the consumption evolution in three 46 LA machines, with internal combustion and two-stroke engines, 7.64 cm3 cylinder capacity, 23.0 millimeters diameter and 18.4 millimeters course, RPM service from 2.000 to 16.000 rpm, 1.2 HP power, and 272 grams weight. The investigated engines components were: (1) head of the engine (Al-Si alloy), (2) piston (Al-Si alloy) and (3) piston pin (AISI 52100 steel). The assays were carried out on a desktop; engines 1 and 2 were assayed with no load, whereas in two assays of engine 3 we added a fan with wind speed that varied from 8.10 m/s to 11.92 m/s, in order to identify and compare the engine dynamic behavior as related to the engines assayed with no load. The temperatures of the engine s surface and surroundings were measured by two type K thermopairs connected to the assay device and registered in a microcomputer with data recording and parameters control and monitoring software, throughout the assays. The consumed surface of the components was analyzed by scanning electron microscopy (SEM) and microanalysis-EDS. The study was complemented with shape deformation and mass measurement assays. The temperature variation was associated with the oxides morphology and the consumption mechanisms were discussed based on the relation between the thermal mechanical effects and the responses of the materials characterization

Mecanismos de desgaste de poliuretano em ensaios de microabrasão

Wear mechanisms and thermal history of two non-conforming sliding surfaces was investigated in laboratory. A micro-abrasion testing setup was used but the traditional rotative sphere method was substituted by a cylindrical surface of revolution which included seven sharp angles varying between 15o to 180o. The micro-abrasion tests lead to the investigation on the polyurethane response at different contact pressures. For these turned counterfaces with and without heat treatment. Normal load and sliding speeds were changed. The sliding distance was fixed at 5 km in each test. The room and contact temperatures were measured during the tests. The polyurethane was characterized using tensile testing, hardness Shore A measurement, Thermogravimetric Analysis (TGA), Differential Scanning Calorimetry (DSC) and Thermomechanical Analyze (TMA). The Vickers micro-hardness of the steel was measured before and after the heat treatment and the metallographic characterization was also carried out. Worn surface of polyurethane was analysed using Scanning Electron Microscope (SEM) and EDS (Electron Diffraction Scanning) microanalyses. Single pass scratch testing in polyurethane using indenters with different contact angles was also carried out. The scar morphology of the wear, the wear mechanism and the thermal response were analyzed in order to correlate the conditions imposed by the pressure-velocity pair to the materials in contact. Eight different wear mechanisms were identified on the polyurethane surface. It was found correlation between the temperature variation and the wear scar morphology.

Eficácia da utilização de grânulos de argila como veículo para a aplicação aérea de sulfentrazone e isoxaflutole em área de implantação de eucalipto

Realizou-se um experimento em uma área de implantação da cultura do eucalipto no município de São Miguel Arcanjo-SP, com o objetivo de avaliar a eficácia da aplicação aérea de grânulos de argila como veículo dos herbicidas sulfentrazone e isoxaflutole, no controle de plantas daninhas. Foi realizada aplicação aérea dos herbicidas sulfentrazone, nas doses de 500 e 750 g i.a. ha-1, e isoxaflutole, nas doses de 150 e 225 g i.a. ha-1, utilizando-se como veículo grânulos de argila com densidade de 1,05 g cm ³, alta capacidade de absorção (24 mL 100 g-1), alta resistência ao desgaste e tamanho das partículas entre 500 mícrons e 1 mm. Também foram feitas aplicações via líquida dos mesmos herbicidas e doses com um pulverizador convencional, acoplado a um trator. Além desses tratamentos, foi mantida uma parcela testemunha, sem aplicação dos herbicidas. Nas parcelas experimentais foram semeadas as espécies de plantas daninhas Brachiaria decumbens, Ipomoea grandifolia, Merremia cissoides e Panicum maximum, sendo realizadas avaliações visuais de controle aos 75 e 110 dias após a aplicação. em geral, foram observados, nas plantas daninhas avaliadas, resultados de controle semelhantes ou superiores para a aplicação aérea (via grânulos) até 75 DAA e superiores para essa modalidade de aplicação aos 110 DAA, indicando uma extensão no período do efeito do residual dos herbicidas estudados.

Resiliência no trabalho contemporâneo: promoção e/ou desgaste da saúde mental

Este estudo teórico resgata a concepção processual e contextual de resiliência, a qual compreende esse fenômeno enquanto relação complexa entre indivíduo e ambiente na produção de fatores de risco e no provimento de fatores protetores da subjetividade do indivíduo, buscando aplicá-la à realidade organizacional, haja vista que o mundo do trabalho contemporâneo demanda uma força de trabalho específica, qual seja, o trabalhador flexível, polivalente, sujeito a mudanças - portanto, um trabalhador resiliente. A partir dessas considerações, realiza-se um processo de reflexão sobre as situações em que a resiliência pode ser promotora de saúde mental, bem como acerca dos contextos que contribuem para o processo de adoecimento do trabalhador, buscando aventar possibilidades de atuação do profissional psicólogo diante de um contexto de trabalho adverso, considerando-se que o principal objetivo dessa atuação profissional é garantir a proteção/promoção da saúde e qualidade de vida no ambiente de trabalho.

Avaliação do desgaste abrasivo causado pelas cerâmicas Duceram e Vita em resinas compostas pelo método do disco retificado

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Influência de defeitos e diferentes processos de fabricação nas propriedades mecânicas finais de cerâmicas

Os materiais cerâmicos são atualmente cada vez utilizados como opção na engenharia mundial. Por se tratar de materiais com alta resistência mecânica, possuem muitas aplicações em diversas áreas, como por exemplo a de mancais, a automotiva (sensores, isoladores, catalisadores, pistões, válvulas, revestimentos), a de implantes biocompatíveis (dentário, substituição óssea, válvulas cardíacas), a de produtos sujeitos ao desgaste (guias), a de refratários (revestimento de equipamento bélico, componentes de fornos), a eletrônica, e outras. Nos processos de fabricação da cerâmica há uma gama de fatores que contribuem para as características do produto final. Devido a isso, muitos pesquisadores têm trabalhado no estudo da influência de determinados defeitos e técnicas de produção de cerâmicas nas características do produto final. Este trabalho tem como objetivo fazer uma revisão bibliográfica de recentes artigos que analisam a influência de fatores como velocidade de queima, surgimento de trincas, porosidade, fases cristalinas, e tamanho de partículas, nas propriedades mecânicas finais das cerâmicas. Pode-se concluir que é possível aperfeiçoar o processo de fabricação da cerâmica a fim de promover as melhores propriedades mecânicas possíveis, conhecendo-se fatores prejudiciais e métodos adequados para se obter o melhor produto final.

Comparação dos valores de desgaste abrasivo e de microdureza de 13 resinas compostas usadas em odontologia através do método do disco retificado

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Análise da influência dos diferentes tempos de polimerização por luz incandescente sobre a resistência ao desgaste abrasivo de resinas compostas

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Estados estacionários de partículas sem spin em potenciais quadrados

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

As fontes de desgaste físico e emocional e a Síndrome de Burnout no setor de transporte coletivo urbano de Natal

Recognizing the importance the workplace has on mental health of the individual, the objective of this study was to investigate the relationship between the burnout syndrome and the sources of physical and emotional wear which permeate the work conditions of the urban public transport system of the city of Natal. Although existent in international literature, research on burnout in the professional transport category and studies directed to this category are not a tradition in Brazil. The research was carried out using 412 drivers and money-changers of two transport companies of Natal. To collect the data, two questionnaires and a semi-structured interview were used. The first instrument, developed and validated during the research, investigated the sources of wear and the second, the syndrome of burnout. As its main results, two sources of empirical wear were identified as follows: (1) the Conflict of Values and the Lack of Justice at the Workplace, (2) Union and Reward. Besides these, it was observed that there is an incidence of the syndrome of burnout among the drivers and money-changers of urban transport by bus, not only in the caring occupations studied before in Natal and Brazil and that this incidence is related to the sources of wear which permeate the work conditions of these professionals