Simultaneous measurements of thickness and temperature profile of the lubricant film at chip-tool interface during machining process using luminescent sensors

Simultaneous measurements of thickness and temperature profile of the lubricant film at chip-tool interface during machining have been studied in this experimental programme. Conventional techniques such as thermography can only provide temperature measurement under controlled environment in a laboratory and without the addition of lubricant. The present study builds on the capabilities of luminescent sensors in addition to direct image based observations of the chip-tool interface. A suite of experiments conducted using different types of sensors are reported in this paper, especially noteworthy are concomitant measures of thickness and temperature of the lubricant. (C) 2014 Elsevier Ltd.

Part II: Design of Well Doping Profile for Improved Breakdown and Mixed-Signal Performance of STI-Type DePMOS Device

Shallow-trench isolation drain extended pMOS (STI-DePMOS) devices show a distinct two-stage breakdown. The impact of p-well and deep-n-well doping profile on breakdown characteristics is investigated based on TCAD simulations. Design guidelines for p-well and deep-n-well doping profile are developed to shift the onset of the first-stage breakdown to a higher drain voltage and to avoid vertical punch-through leading to early breakdown. An optimal ratio between the OFF-state breakdown voltage and the ON-state resistance could be obtained. Furthermore, the impact of p-well/deep-n-well doping profile on the figure of merits of analog and digital performance is studied. This paper aids in the design of STI drain extended MOSFET devices for widest safe operating area and optimal mixed-signal performance in advanced system-on-chip input-output process technologies.

On the initial unloading slope in indentation of elastic-plastic solids by an indenter with an axisymmetric smooth profile

A simple relationship between the initial unloading slope, the contact area, and the elastic modulus is derived for indentation in elastic-plastic solids by an indenter with an arbitrary axisymmetric smooth profile. Although the same expression was known to hold for elastic solids, the new derivation shows that it is also true for elastic-plastic solids with or without work hardening and residual stress. These results should provide a sound basis for the use of the relationship for mechanical property determination using indentation techniques. (C) 1997 American Institute of Physics.

Spectral-line profile of turbulent gas

phases should be specified when the particle Reynolds number is higher than

Measurement of Electron Density Profile Behind Strong Shock Waves with a Langmuir Probe

At the shock velocity range of 7~9km/s, the variations of electron density behind strong normal shock waves are measured in a low-density shock tube by using the Langmuir electrostatic probe technique. The electron temperature, calculated based on Park’s three-temperature model, is used in interpreting the probe current data. The peak electron densities determined in the present experiment are shown to be in a good agreement with those predicted by Lin’s calculation. The experimentally obtained ratios of the characteristic ionization distance to the mean free path of freestream ahead of the shock wave are found to be in a good agreement with the existing experiments and Park’s calculation.

Scientific Data Application Profile Scoping Study

This study was undertaken by UKOLN on behalf of the Joint Information Systems Committee (JISC) in the period April to September 2008. Application profiles are metadata schemata which consist of data elements drawn from one or more namespaces, optimized for a particular local application. They offer a way for particular communities to base the interoperability specifications they create and use for their digital material on established open standards. This offers the potential for digital materials to be accessed, used and curated effectively both within and beyond the communities in which they were created. The JISC recognized the need to undertake a scoping study to investigate metadata application profile requirements for scientific data in relation to digital repositories, and specifically concerning descriptive metadata to support resource discovery and other functions such as preservation. This followed on from the development of the Scholarly Works Application Profile (SWAP) undertaken within the JISC Digital Repositories Programme and led by Andy Powell (Eduserv Foundation) and Julie Allinson (RRT UKOLN) on behalf of the JISC. Aims and Objectives 1.To assess whether a single metadata AP for research data, or a small number thereof, would improve resource discovery or discovery-to-delivery in any useful or significant way. 2.If so, then to:a.assess whether the development of such AP(s) is practical and if so, how much effort it would take; b.scope a community uptake strategy that is likely to be successful, identifying the main barriers and key stakeholders. 3.Otherwise, to investigate how best to improve cross-discipline, cross-community discovery-to-delivery for research data, and make recommendations to the JISC and others as appropriate. Approach The Study used a broad conception of what constitutes scientific data, namely data gathered, collated, structured and analysed using a recognizably scientific method, with a bias towards quantitative methods. The approach taken was to map out the landscape of existing data centres, repositories and associated projects, and conduct a survey of the discovery-to-delivery metadata they use or have defined, alongside any insights they have gained from working with this metadata. This was followed up by a series of unstructured interviews, discussing use cases for a Scientific Data Application Profile, and how widely a single profile might be applied. On the latter point, matters of granularity, the experimental/measurement contrast, the quantitative/qualitative contrast, the raw/derived data contrast, and the homogeneous/heterogeneous data collection contrast were discussed. The Study report was loosely structured according to the Singapore Framework for Dublin Core Application Profiles, and in turn considered: the possible use cases for a Scientific Data Application Profile; existing domain models that could either be used or adapted for use within such a profile; and a comparison existing metadata profiles and standards to identify candidate elements for inclusion in the description set profile for scientific data. The report also considered how the application profile might be implemented, its relationship to other application profiles, the alternatives to constructing a Scientific Data Application Profile, the development effort required, and what could be done to encourage uptake in the community. The conclusions of the Study were validated through a reference group of stakeholders.

Building digital capability: Example learner profile

This is a version of the Jisc ‘Six Elements of Digital Capabilities’ model, specifically for learners. It is an update on the earlier ‘7 elements of digital literacy’ model (2009) and has many continuities with this framework. This version was produced in response to feedback that the base model alone does not provide enough detail to support embedding into practice. However, it is an example of how the base model could be used to define the digital capabilities of learners and is meant to be adapted to suit specific settings.

Building digital capability: Example researcher profile

This is a version of the Jisc ‘Six Elements of Digital Capabilities’ model, specifically for research students and research sta . It is an update on the earlier ‘7 elements of digital literacy’ model (2009) and has many continuities with this framework. It is one example of how the base model is being used.

Building digital capability: Example teacher profile

This is a version of the Jisc ‘Six Elements of Digital Capabilities’ model, specifically for teaching sta or for academic sta in their teaching role. It is an update on the earlier ‘7 elements of digital literacy’ model (2009) and has many continuities with this framework. This version was produced in response to feedback that the base model alone does not provide enough detail to support embedding into practice. However, it is an example of how the base model could be used to define the digital capabilities of teaching sta and is meant to be adapted to suit specific settings.

Design of an optimised wheel profile for rail vehicles operating on two track gauges

This paper sets out an optimum synthesis methodology for wheel profiles of railway vehicles in order to secure good dynamic behaviour with different track configurations. Specifically, the optimisation process has been applied to the case of rail wheelsets mounted on double gauge bogies, that move over two different gauges, which also have different types of rail: the Iberian gauge (1668 mm) and the UIC gauge (1435 mm). Optimisation is performed using Genetic Algorithms and traditional optimisation methods in a complementary way. The objective function used is based on an ideal equivalent conicity curve which ensures good stability on straight sections and also proper negotiation of curves. To this end the curve is constructed in such a way that it is constant with a low value for small lateral wheelset displacements (with regard to stability), and increases as the displacements increase (to facilitate negotiation of curved sections). Using this kind of ideal conicity curve also enables a wheel profile to be secured where the contact points have a larger distribution over the active contact areas, making wear more homogeneous and reducing stresses. The result is a wheel profile with a conicity that is closer to the target conicity for both gauges studied, producing better curve negotiation while maintaining good stability on straight sections of track. The paper shows the resultant wheel profile, the contact curves it produces, and a number of dynamic analyses demonstrating better dynamic behaviour of the synthesised wheel on curved sections with respect to the original wheel.