influência da adição de diferentes sais em pastas de cimento portland para cimentação de poços de petróleo

One of the great challenges at present time related with the materials area concerns of products and processes for use in petroleum industry, more precisely related to the Pre-salt area. Progresses were reached in the last years allowing the drilling of the salt layer, with the time reduction for drilling and larger success at the end. For the oil wells companies the preponderant factor is the technology, however, in spite of the progress, a series of challenges is still susceptible to solutions and one of them refers to the slurries preparation for cementing in those areas. Inside of this context, this study had for objective to analyze the influence of the salts NaCl, KCl, CaSO4 and MgSO4 in strength and chemical structure of the hydrated products. As methodology, they were prepared and analyzed cement slurries with varied concentrations of these salts that are commonly found in the saline formations. The salts concentrations used in formulations of the slurries were of 5%, 15% and 30%. The slurries were formulated with specific weight of 15,8 lb / gal and the cement used was Class G. Strength tests were accomplished in samples cured by 24 hours and 28 days. Also were realized crystallographic characterization (XRD) and morphologic (SEM). In agreement with the presented results, it is observed that the largest resistance values are attributed to the slurries with concentration of 15%. There was reduction of the strength values of the slurries formulated with concentration of 30%. Through the characterization microstructural it was possible to note the salts influence in the main cement hydrated products

Avaliação da adição de Nanosílica e silicato de sódio em pastas de cimento para poços de petróleo com baixo gradiente de fratura

The oil wells cementing is a critical step during the phase of well drilling, because problems during the operation of slurry pumping and an incomplete filling of the annular space between the metal casing and the formation can cause the slurry loss. Therefore, the slurry adopted in primary cementing an oil well must be properly dosed so that these problems are avoided during its pumping. When you drill a well in a weak rock formation requires even more careful, because should be a limit of hydrostatic pressure exerted during cementation, that does not occur rock collapse. With the objective of performing the cementing of a well whose formation is weak or unconsolidated are employed lighter slurries. Thus, this study used slurries with sodium silicate and nano silica in concentrations of 0,1; 0,4; 0,7 e 1,0 gpc, in which the slurries with nano silica showed the rheological parameters higher concentrations of up to 0.7 gpc and for concentration of 1.0 the slurry with sodium silicate obtained the highest values, remaining above the limits for application in fields, mainly wells with low fracture gradient, because a significant increase in viscosity may result in an increase in pressure pumping in operations of secondary cementations. Furthermore, there was no decrease in strength with increasing concentration of additive. Then, it is possible use of these additives to formulate Lighter slurry

Avaliação do comportamento reológico de pastas de cimento para poços de petróleo com adição de plastificantes

The isolation of adjacent zones encountered during oilwell drilling is carried out by Portland-based cement slurries. The slurries are pumped into the annular positions between the well and the casing. Their rheological behavior is a very important component for the cementing process. Nowadays, several alternative materials are used in oilwell cementing, with goal the modification and the improvement of their properties, mainly the increase of the fluidity. And this can be reached by using plasticizers additives able to account for different oilwell conditions, yielding compatible cement slurries and allowing enough time for the complete cementing operation. If the rheological properties of the slurry are properly characterized, the load loss and flow regime can be correctly predicted. However, this experimental characterization is difficult. Rheological models capable of describing the cement slurry behavior must be capable of predicting the slurry cement deformation within reasonable accuracy. The aim of this study was to characterize rheologically the slurries prepared with a especial class of Portland cement, water and plasticizers based on lignosulfonate, melamine and polycarboxylate at temperatures varying from 27°C to 72°C. The tests were carried out according to the practical recommendations of the API RP 10B guidelines. The results revealed a great efficiency and the dispersive power of the polycarboxylate, for all temperatures tested. This additive promoted high fluidity of the slurries, with no sedimentation. High lignosulfonate and melamine concentrations did not reduce the rheological parameters (plastic viscosity and yield stress) of the slurries. It was verified that these additives were not compatible with the type of cement used. The evaluated rheological models were capable of describing the behavior of the slurries only within concentration and temperature ranges specific for each type of additive

Avaliação da incorporação combinada dos resíduos de cascalho de perfuração de poço de petróleo e de polimento do porcelanato em cerâmica vermelha

Among the industries, those that produce ceramic porcelain for use in construction industry and oil, during the exploration and production period, play an important role in the production of waste. Much research has been carried out both by academia and the productive sector, sometimes reintroducing them in the same production line that generated them, sometimes in areas unrelated to their generation, as in the production of concrete and mortar for the construction, for example, but each one in an isolated way. In this research, the aim is to study the combined incorporation of the waste drill cuttings of oil well and the residue of the polishing of porcelain, generated in the final stage of finishing of this product in a clay matrix, for the production of red pottery, specifically bricks, ceramic blocks and tiles. The clay comes from the municipality of São Gonçalo, RN, the drilling waste is from the Natal basin, in Rio Grande do Norte, and the residue of the polishing proceeds from a ceramic porcelain of the State of Paraíba. For this purpose, we used a mixture of a plastic clay with a non-plastic, in a ratio of 50% each, settling formulations with the addition of these two residues in this clay matrix. In the formulations, both residues were incorporated with a minimum percentage of 2.5% and maximum of 12.5%, varying from 2.5% each, in each formulation, which the sum of the waste be no more than 15%. It should be noted that the residue of the polishing of ceramic porcelain is a IIa class (not inert). The materials were characterized by XRF, XRD, TG, DTA, laser granulometry and the plasticity index. The technological properties of water absorption, apparent porosity, linear shrinkage of burning, flexural tensile strength and bulk density were evaluated after the sintering of the pieces to 850 °C, 950 °C and 1050 °C, with a burning time of 3 hr, 3 hr and 30 minutes, and 3 hr and 50 minutes, respectively, with a heating rate of 10 °C/minute, for all formulations and landing of 30 minutes. To better understand the influence of each residue and temperature on the evaluated properties, we used the factorial planning and its surfaces of response for the interpretation of the results. It was found that the temperature has no statistical significance at a 95% of reliability level in flexural tensile strength and that it decreases the water absorption and the porosity, but increases the shrinkage and the bulk density. The results showed the feasibility of the desired incorporation, but adjusting the temperature to each product and formulation, and that the temperatures of 850 °C and 950 °C were the one that responded to the largest number of formulations

Ambiente para avaliação de controladores fuzzy aplicados ao método de elevação artificial por bombeio centrífugo submerso

From their early days, Electrical Submergible Pumping (ESP) units have excelled in lifting much greater liquid rates than most of the other types of artificial lift and developed by good performance in wells with high BSW, in onshore and offshore environments. For all artificial lift system, the lifetime and frequency of interventions are of paramount importance, given the high costs of rigs and equipment, plus the losses coming from a halt in production. In search of a better life of the system comes the need to work with the same efficiency and security within the limits of their equipment, this implies the need for periodic adjustments, monitoring and control. How is increasing the prospect of minimizing direct human actions, these adjustments should be made increasingly via automation. The automated system not only provides a longer life, but also greater control over the production of the well. The controller is the brain of most automation systems, it is inserted the logic and strategies in the work process in order to get you to work efficiently. So great is the importance of controlling for any automation system is expected that, with better understanding of ESP system and the development of research, many controllers will be proposed for this method of artificial lift. Once a controller is proposed, it must be tested and validated before they take it as efficient and functional. The use of a producing well or a test well could favor the completion of testing, but with the serious risk that flaws in the design of the controller were to cause damage to oil well equipment, many of them expensive. Given this reality, the main objective of the present work is to present an environment for evaluation of fuzzy controllers for wells equipped with ESP system, using a computer simulator representing a virtual oil well, a software design fuzzy controllers and a PLC. The use of the proposed environment will enable a reduction in time required for testing and adjustments to the controller and evaluated a rapid diagnosis of their efficiency and effectiveness. The control algorithms are implemented in both high-level language, through the controller design software, such as specific language for programming PLCs, Ladder Diagram language.

Relación entre los riesgos percibidos por los trabajadores en minería subterránea y los accidentes de trabajo y enfermedades laborales

Introducción: La minería es considerada uno de los sectores económicos más importantes por su capacidad para generar recursos en su propio sector y en otros sectores como metalmecánica, agricultura e informática entre otros, y por su contribución al desarrollo socioeconómico sostenible de las poblaciones. Objetivo: Determinar la relación entre los riesgos percibidos por los trabajadores que laboran en minería subterránea en 3 departamentos de Colombia y los Accidentes de Trabajo (AT) y Enfermedades Laborales (EL). Materiales y Métodos: Estudio de corte transversal en 476 trabajadores de minería subterránea. Se incluyeron variables independientes (características sociodemográficas y laborales y percepción del riesgo) y variables dependientes (enfermedad laboral y accidente de trabajo), obtenidas a través de una entrevista directa aplicada por profesionales de la salud previamente capacitados. Para el análisis estadístico se utilizó la Prueba Exacta de Fisher, el Odds Ratio (OR) con el Intervalo de Confianza (IC) del 95%. Resultados: En los trabajadores de minería subterránea en los departamentos de Boyacá, Cundinamarca y Santander, se encontró relación estadística significativa entre la accidentalidad con la percepción de riesgo por iluminación (OR= 2.059, IC= 95%: 1.116, 3.798, p=0.013), percepción de riesgo por movimientos repetitivos (OR= 1.951, IC= 95%: 0.998, 3.815, p=0.034), percepción de riesgo por ruido (OR= 2.275, IC= 95%: 0.974, 5.312, p=0.039) y percepción de riesgo por manejo de cargas (OR= 1.778, IC= 95%: 0.969, 3.264, p=0.041). Conclusión: se encontró que existe una relación significativa entre la percepción de riesgo de los trabajadores de minería subterránea con accidentes de trabajo y que no existe relación entre esta percepción y las enfermedades laborales.

ESEM study of authigenic chlorite acid sensitivity in sandstone reservoirs

The effect of HCl on authigenic chlorite in three different sandstones has been examined uisng an Environmental Scanning Electron Microscope (ESEM), together with conventional analytical techniques. The ESEM enabled chlorites to be directly observed in situ at high magnifications during HCl treatment, and was particularly effective in allowing the same chlorite areas to be closely compared before and after acid treatment. Chlorites were reacted with 1M to 10M HCl at temperatures up to 80°C and for periods up to five months. After all treatments, chlorites show extensive leaching of iron, magnesium and aluminum, and their crystalline structure is destroyed. However, despite these major compositional and structural changes, chlorites show little or no visible evidence of acid attack, with precise morphological detail of individual plates preserved in all samples following acid treatments. Chlorite dissolution, sensu stricto, did not occur as a result of acidization of the host sandstones. Acid-treated chlorides are likely to exits in a structurally weakened state that may make them susceptible to physical disintegration during fluid flow. Accordingly, fines migration may be a significant engineering problem associated with the acidization of chlorite-bearing sandstones. © 1993.

Taking cues from outer space : the E&P sector can learn much about asset maintenance from the space and satellite industry

The E&P sector can learn much about asset maintenance from the space and satellite industry. Practitioners from both the upstream oil and gas industry and the space and satellite sector have repeatedly noted several striking similarities between the two industries over the years, which have in turn resulted in many direct comparisons in the media and industry press. The similarities between the two industries have even resulted in a modest amount of cross-pollinating between the respective supply chains. Because the operating conditions of both industries are so extreme, some oil and gas equipment vendors have occasionally sourced motors and other parts from aerospace contractors. Also, satellites are now being used to assess oil fires, detect subsidence in oil fields, measure oil spills, collect and transmit operational data from oil and gas fields, and monitor the movement of icebergs that might potentially collide with offshore oil and gas installations.

固井工程中的流动问题

同井是油气在建过程中的重要工程，一般分下套管和注水泥两个过程．本文结合作者近年来的研究，着重阐述了钻井液、前置液、水泥浆在环形空间中流动的流体力学问题，包括：高温高压下的水泥浆流变性、偏心环形空间中浆液的流动特性、钻井液-前置液和前置液-水泥浆界面的稳定性等，介绍了国内外学者对这些问题的研究进展，提出了今后应深入研究的问题.

电潜泵井生产动态分析

提出了原油物性模拟的修正模型，其结果与PVT曲线具有良好的相关性。给出了电潜泵内流体温升及井筒中流体温度梯度的计算方法。通过引入井眼轨迹的描述与计算描述，成功地解决了弯曲井段的多相流计算问题，从而可以计算出任意井眼形状中的参数分布规律。在此基础上，借助于毛细管、动液面或泵特性测试资料，实现了对电潜泵井生产动态的模拟和分析，并在现场应用中收到了良好的效果。

Proposição de um indicador global de funcionalidade operacional para sistemas de processamento primário em instalações marítimas de produção de petróleo: estudo de caso para o sistema de separação e tratamento de óleo

Este texto verificou o tema de monitoramento de processos de produção de petróleo em plataformas no mar de forma a propor indicadores globais para monitoramento da funcionalidade dos equipamentos que envolvem estes processos, permitindo a antecipação da tomada de decisão sobre suas eminentes quedas de disponibilidade. Para tal, buscando conhecer as áreas envolvidas na gestão de uma plataforma de petróleo no mar, foram identificados os principais sistemas relacionados ao processo de produção de petróleo e optou-se pelo Sistema de Separação e Tratamento de Óleo para desenvolvimento e validação dos indicadores propostos. O Indicador Global de Funcionalidade Operacional (IGFO) foi desenvolvido a partir dos dados disponíveis para monitoramento dos processos de produção de petróleo, focado nas visões das principais áreas envolvidas na gestão da plataforma. Este indicador foi elaborado com objetivo de simplificar a análise dos processos, permitindo assim aferir o desempenho das ações de monitoramento de processos em plataformas de petróleo, de modo a atuar de forma antecipativa, contribuindo com a identificação e a disseminação das melhores práticas de manutenção preditiva. Neste aspecto, os indicadores na forma de normalização utilizada permitem comparações em diversos níveis, tanto em relação as plataformas dentro de uma empresa, como plataformas de empresas diferentes. Os indicadores globais propostos obtiveram resultados que permitiram avaliar a queda de funcionalidade dos equipamentos do Sistema de Separação e Tratamento de Óleo durante o período avaliado, servindo de base para identificação das causas das falhas destes equipamentos. Assim sendo, pôde-se perceber que a utilização dos indicadores globais identificados pode responder com sucesso às necessidades propostas

Beluga, Delphinapterus leucas, Habitat Associations in Cook Inlet, Alaska

A review of available information describing habitat associations for belugas, Delphinapterus leucas, in Cook Inlet was undertaken to complement population assessment surveys from 1993-2000. Available data for physical, biological, and anthropogenic factors in Cook Inlet are summarized followed by a provisional description of seasonal habitat associations. To summarize habitat preferences, the beluga summer distribution pattern was used to partition Cook Inlet into three regions. In general, belugas congregate in shallow, relatively warm, low-salinity water near major river outflows in upper Cook Inlet during summer (defined as their primary habitat), where prey availability is comparatively high and predator occurrence relatively low. In winter, belugas are seen in the central inlet, but sightings are fewer in number, and whales more dispersed compared to summer. Belugas are associated with a range of ice conditions in winter, from ice-free to 60% ice-covered water. Natural catastrophic events, such as fires, earthquakes, and volcanic eruptions, have had no reported effect on beluga habitat, although such events likely affect water quality and, potentially, prey availability. Similarly, although sewage effluent and discharges from industrial and military activities along Cook Inlet negatively affect water quality, analyses of organochlorines and heavy metal burdens indicate that Cook Inlet belugas are not assimilating contaminant loads greater than any other Alaska beluga stocks. Offshore oil and gas activities and vessel traffic are high in the central inlet compared with other Alaska waters, although belugas in Cook Inlet seem habituated to these anthropogenic factors. Anthropogenic factors that have the highest potential negative impacts on belugas include subsistence hunts (not discussed in this report), noise from transportation and offshore oil and gas extraction (ship transits and aircraft overflights), and water quality degradation (from urban runoff and sewage treatment facilities). Although significant impacts from anthropogenic factors other than hunting are not yet apparent, assessment of potential impacts from human activities, especially those that may effect prey availability, are needed.