Towards Information-Centric Wireless Multi-hop Communication

Information-centric networking (ICN) addresses drawbacks of the Internet protocol, namely scalability and security. ICN is a promising approach for wireless communication because it enables seamless mobile communication, where intermediate or source nodes may change, as well as quick recovery from collisions. In this work, we study wireless multi-hop communication in Content-Centric Networking (CCN), which is a popular ICN architecture. We propose to use two broadcast faces that can be used in alternating order along the path to support multi-hop communication between any nodes in the network. By slightly modifying CCN, we can reduce the number of duplicate Interests by 93.4 % and the number of collisions by 61.4 %. Furthermore, we describe and evaluate different strategies for prefix registration based on overhearing. Strategies that configure prefixes only on one of the two faces can result in at least 27.3 % faster data transmissions.

Using the Spectrum Analyzer as an Educational Tool for Mobile Communications

Application of the spectrum analyzer for illustrating several concepts associated with mobile communications is discussed. Specifically, two groups of observable features are described. First, time variation and frequency selectivity of multipath propagation can be revealed by carrying out simple measurements on commercial-network GSM and UMTS signals. Second, the main time-domain and frequency-domain features of GSM and UMTS radio signals can be observed. This constitutes a valuable tool for teaching mobile communication courses.

Supporting eradication of maternal child malnutrition in developing countries: a case from Nicaragua scenario.

World Health Organization actively stresses the importance of health, nutrition and well-being of the mother to foster children development. This issue is critical in the rural areas of developing countries where monitoring of health status of children is hardly performed since population suffers from a lack of access to health care. The aim of this research is to design, implement and deploy an e-health information and communication system to support health care in 26 rural communities of Cusmapa, Nicaragua. The final solution consists of an hybrid WiMAX/WiFi architecture that provides good quality communications through VoIP taking advantage of low cost WiFi mobile devices. Thus, a WiMAX base station was installed in the health center to provide a radio link with the rural health post "El Carrizo" sited 7,4 km. in line of sight. This service makes possible personal broadband voice and data communication facilities with the health center based on WiFi enabled devices such as laptops and cellular phones without communications cost. A free software PBX was installed at "San José de Cusmapa" health care site to enable communications for physicians, nurses and a technician through mobile telephones with IEEE 802.11 b/g protocol and SIP provided by the project. Additionally, the rural health post staff (midwives, brigade) received two mobile phones with these same features. In a complementary way, the deployed health information system is ready to analyze the distribution of maternal-child population at risk and the distribution of diseases on a geographical baseline. The system works with four information layers: fertile women, children, people with disabilities and diseases. Thus, authorized staff can obtain reports about prenatal monitoring tasks, status of the communities, malnutrition, and immunization control. Data need to be updated by health care staff in order to timely detect the source of problem to implement measures addressed to alleviate and improve health status population permanently. Ongoing research is focused on a mobile platform that collects and automatically updates in the information system, the height and weight of the children locally gathered in the remote communities. This research is being granted by the program Millennium Rural Communities of the Technical University of Madrid.

Implementation of wireless communication based on Software Defined Radio

In current communication systems, there are many new challenges like various competitive standards, the scarcity of frequency resource, etc., especially the development of personal wireless communication systems result the new system update faster than ever before, the conventional hardware-based wireless communication system is difficult to adapt to this situation. The emergence of SDR enabled the third revolution of wireless communication which from hardware to software and build a flexible, reliable, upgradable, reusable, reconfigurable and low cost platform. The Universal Software Radio Peripheral (USRP) products are commonly used with the GNU Radio software suite to create complex SDR systems. GNU Radio is a toolkit where digital signal processing blocks are written in C++, and connected to each other with Python. This makes it easy to develop more sophisticated signal processing systems, because many blocks already written by others and you can quickly put them together to create a complete system. Although the main function of GNU Radio is not be a simulator, but if there is no RF hardware components,it supports to researching the signal processing algorithm based on pre-stored and generated data by signal generator. This thesis introduced SDR platform from hardware (USRP) and software(GNU Radio), as well as some basic modulation techniques in wireless communication system. Based on the examples provided by GNU Radio, carried out some related experiments, for example GSM scanning and FM radio station receiving on USRP. And make a certain degree of improvement based on the experience of some investigators to observe OFDM spectrum and simulate real-time video transmission. GNU Radio combine with USRP hardware proved to be a valuable lab platform for implementing complex radio system prototypes in a short time. RESUMEN. Software Defined Radio (SDR) es una tecnología emergente que está creando un impacto revolucionario en la tecnología de radio convencional. Un buen ejemplo de radio software son los sistemas de código abierto llamados GNU Radio que emplean un kit de herramientas de desarrollo de software libre. En este trabajo se ha empleado un kit de desarrollo comercial (Ettus Research) que consiste en un módulo de procesado de señal y un hardaware sencillo. El módulo emplea un software de desarrollo basado en Linux sobre el que se pueden implementar aplicaciones de radio software muy variadas. El hardware de desarrollo consta de un microprocesador de propósito general, un dispositivo programable (FPGA) y un interfaz de radiofrecuencia que cubre de 50 a 2200MHz. Este hardware se conecta al PC por medio de un interfaz USB de 8Mb/s de velocidad. Sobre la plataforma de Ettus se pueden ejecutar aplicaciones GNU radio que utilizan principalmente lenguaje de programación Python para implementarse. Sin embargo, su módulo de procesado de señal está construido en C + + y emplea un microprocesador con aritmética de coma flotante. Por lo tanto, los desarrolladores pueden rápida y fácilmente construir aplicaciones en tiempo real sistemas de comunicación inalámbrica de alta capacidad. Aunque su función principal no es ser un simulador, si no puesto que hay componentes de hardware RF, Radio GNU sirve de apoyo a la investigación del algoritmo de procesado de señales basado en pre-almacenados y generados por los datos del generador de señal. En este trabajo fin de máster se ha evaluado la plataforma de hardware de DEG (USRP) y el software (GNU Radio). Para ello se han empleado algunas técnicas de modulación básicas en el sistema de comunicación inalámbrica. A partir de los ejemplos proporcionados por GNU Radio, hemos realizado algunos experimentos relacionados, por ejemplo, escaneado del espectro, demodulación de señales de FM empleando siempre el hardware de USRP. Una vez evaluadas aplicaciones sencillas se ha pasado a realizar un cierto grado de mejora y optimización de aplicaciones complejas descritas en la literatura. Se han empleado aplicaciones como la que consiste en la generación de un espectro de OFDM y la simulación y transmisión de señales de vídeo en tiempo real. Con estos resultados se está ahora en disposición de abordar la elaboración de aplicaciones complejas.

Sistema de control de temperatura a través de Arduino y la tecnología GPRS/GSM

El principal objetivo de este proyecto consiste en estudiar las posibilidades de desarrollo de un sistema para el control de la temperatura basado en la plataforma Arduino. Con el fin de alcanzar dicho objetivo, se ha implementado un sistema que permite la consulta y control de la temperatura ambiente a través de la red de comunicaciones móviles. Tras un análisis previo de las distintas placas Arduino, se evalúan una serie de módulos de expansión (shields) compatibles con dicha plataforma que nos permiten ampliar sus funcionalidades, dotando al dispositivo de un sistema de comunicación basado en la tecnología GPRS/GSM. Se estudian los diferentes sensores de temperatura compatibles con Arduino, además de una serie de actuadores que contribuyen al accionamiento y control de un posible termostato, así como al desarrollo de un pequeño sistema de alarma capaz de detectar temperaturas extremas. El proyecto concluye con el diseño de una aplicación basada en el entorno de desarrollo Arduino que nos permita evaluar las distintas capacidades de nuestro sistema, así como comunicarnos con la plataforma a través de SMS para el control remoto de la temperatura. ABSTRACT. The goal of the project consists of studying the developmental possibilities of a temperature control system based on the Arduino platform. In order to this, there has been implemented a system to consult and manage the environmental temperature through mobile communication networks. After a previous assessment of the different Arduino boards, there are analysed a set of expansion modules (shields) compatibles with the platform that enables us to upgrade the device functionalities with the GPRS/GSM communication protocol. Different temperature sensors compatible with Arduino have been studied. In addition, there are evaluated a set of actuators for the operation and control of a thermostat and also the development of a small alarm system that alerts of extremes temperatures. The project concludes with the design of an application based on the Arduino development environment which allows us to evaluate the different capabilities of our system as well as the communication with the platform by SMS for the remote temperature control.

Design and Validation of an Optimized MB-OFDM Ultra Wideband Transceiver System

Esta tesis está incluida dentro del campo del campo de Multiband Orthogonal Frequency Division Multiplexing Ultra Wideband (MB-OFDM UWB), el cual ha adquirido una gran importancia en las comunicaciones inalámbricas de alta tasa de datos en la última década. UWB surgió con el objetivo de satisfacer la creciente demanda de conexiones inalámbricas en interiores y de uso doméstico, con bajo coste y alta velocidad. La disponibilidad de un ancho de banda grande, el potencial para alta velocidad de transmisión, baja complejidad y bajo consumo de energía, unido al bajo coste de implementación, representa una oportunidad única para que UWB se convierta en una solución ampliamente utilizada en aplicaciones de Wireless Personal Area Network (WPAN). UWB está definido como cualquier transmisión que ocupa un ancho de banda de más de 20% de su frecuencia central, o más de 500 MHz. En 2002, la Comisión Federal de Comunicaciones (FCC) definió que el rango de frecuencias de transmisión de UWB legal es de 3.1 a 10.6 GHz, con una energía de transmisión de -41.3 dBm/Hz. Bajo las directrices de FCC, el uso de la tecnología UWB puede aportar una enorme capacidad en las comunicaciones de corto alcance. Considerando las ecuaciones de capacidad de Shannon, incrementar la capacidad del canal requiere un incremento lineal en el ancho de banda, mientras que un aumento similar de la capacidad de canal requiere un aumento exponencial en la energía de transmisión. En los últimos años, s diferentes desarrollos del UWB han sido extensamente estudiados en diferentes áreas, entre los cuales, el protocolo de comunicaciones inalámbricas MB-OFDM UWB está considerado como la mejor elección y ha sido adoptado como estándar ISO/IEC para los WPANs. Combinando la modulación OFDM y la transmisión de datos utilizando las técnicas de salto de frecuencia, el sistema MB-OFDM UWB es capaz de soportar tasas de datos con que pueden variar de los 55 a los 480 Mbps, alcanzando una distancia máxima de hasta 10 metros. Se esperara que la tecnología MB-OFDM tenga un consumo energético muy bajo copando un are muy reducida en silicio, proporcionando soluciones de bajo coste que satisfagan las demandas del mercado. Para cumplir con todas estas expectativas, el desarrollo y la investigación del MBOFDM UWB deben enfrentarse a varios retos, como son la sincronización de alta sensibilidad, las restricciones de baja complejidad, las estrictas limitaciones energéticas, la escalabilidad y la flexibilidad. Tales retos requieren un procesamiento digital de la señal de última generación, capaz de desarrollar sistemas que puedan aprovechar por completo las ventajas del espectro UWB y proporcionar futuras aplicaciones inalámbricas en interiores. Esta tesis se centra en la completa optimización de un sistema de transceptor de banda base MB-OFDM UWB digital, cuyo objetivo es investigar y diseñar un subsistema de comunicación inalámbrica para la aplicación de las Redes de Sensores Inalámbricas Visuales. La complejidad inherente de los procesadores FFT/IFFT y el sistema de sincronización así como la alta frecuencia de operación para todos los elementos de procesamiento, se convierten en el cuello de la botella para el diseño y la implementación del sistema de UWB digital en base de banda basado en MB-OFDM de baja energía. El objetivo del transceptor propuesto es conseguir baja energía y baja complejidad bajo la premisa de un alto rendimiento. Las optimizaciones están realizadas tanto a nivel algorítmico como a nivel arquitectural para todos los elementos del sistema. Una arquitectura hardware eficiente en consumo se propone en primer lugar para aquellos módulos correspondientes a núcleos de computación. Para el procesado de la Transformada Rápida de Fourier (FFT/IFFT), se propone un algoritmo mixed-radix, basado en una arquitectura con pipeline y se ha desarrollado un módulo de Decodificador de Viterbi (VD) equilibrado en coste-velocidad con el objetivo de reducir el consumo energético e incrementar la velocidad de procesamiento. También se ha implementado un correlador signo-bit simple basado en la sincronización del tiempo de símbolo es presentado. Este correlador es usado para detectar y sincronizar los paquetes de OFDM de forma robusta y precisa. Para el desarrollo de los subsitemas de procesamiento y realizar la integración del sistema completo se han empleado tecnologías de última generación. El dispositivo utilizado para el sistema propuesto es una FPGA Virtex 5 XC5VLX110T del fabricante Xilinx. La validación el propuesta para el sistema transceptor se ha implementado en dicha placa de FPGA. En este trabajo se presenta un algoritmo, y una arquitectura, diseñado con filosofía de co-diseño hardware/software para el desarrollo de sistemas de FPGA complejos. El objetivo principal de la estrategia propuesta es de encontrar una metodología eficiente para el diseño de un sistema de FPGA configurable optimizado con el empleo del mínimo esfuerzo posible en el sistema de procedimiento de verificación, por tanto acelerar el periodo de desarrollo del sistema. La metodología de co-diseño presentada tiene la ventaja de ser fácil de usar, contiene todos los pasos desde la propuesta del algoritmo hasta la verificación del hardware, y puede ser ampliamente extendida para casi todos los tipos de desarrollos de FPGAs. En este trabajo se ha desarrollado sólo el sistema de transceptor digital de banda base por lo que la comprobación de señales transmitidas a través del canal inalámbrico en los entornos reales de comunicación sigue requiriendo componentes RF y un front-end analógico. No obstante, utilizando la metodología de co-simulación hardware/software citada anteriormente, es posible comunicar el sistema de transmisor y el receptor digital utilizando los modelos de canales propuestos por IEEE 802.15.3a, implementados en MATLAB. Por tanto, simplemente ajustando las características de cada modelo de canal, por ejemplo, un incremento del retraso y de la frecuencia central, podemos estimar el comportamiento del sistema propuesto en diferentes escenarios y entornos. Las mayores contribuciones de esta tesis son: • Se ha propuesto un nuevo algoritmo 128-puntos base mixto FFT usando la arquitectura pipeline multi-ruta. Los complejos multiplicadores para cada etapa de procesamiento son diseñados usando la arquitectura modificada shiftadd. Los sistemas word length y twiddle word length son comparados y seleccionados basándose en la señal para cuantización del SQNR y el análisis de energías. • El desempeño del procesador IFFT es analizado bajo diferentes situaciones aritméticas de bloques de punto flotante (BFP) para el control de desbordamiento, por tanto, para encontrar la arquitectura perfecta del algoritmo IFFT basado en el procesador FFT propuesto. • Para el sistema de receptor MB-OFDM UWB se ha empleado una sincronización del tiempo innovadora, de baja complejidad y esquema de compensación, que consiste en funciones de Detector de Paquetes (PD) y Estimación del Offset del tiempo. Simplificando el cross-correlation y maximizar las funciones probables solo a sign-bit, la complejidad computacional se ve reducida significativamente. • Se ha propuesto un sistema de decodificadores Viterbi de 64 estados de decisión-débil usando velocidad base-4 de arquitectura suma-comparaselecciona. El algoritmo Two-pointer Even también es introducido en la unidad de rastreador de origen con el objetivo de conseguir la eficiencia en el hardware. • Se han integrado varias tecnologías de última generación en el completo sistema transceptor basebanda , con el objetivo de implementar un sistema de comunicación UWB altamente optimizado. • Un diseño de flujo mejorado es propuesto para el complejo sistema de implementación, el cual puede ser usado para diseños de Cadena de puertas de campo programable general (FPGA). El diseño mencionado no sólo reduce dramáticamente el tiempo para la verificación funcional, sino también provee un análisis automático como los errores del retraso del output para el sistema de hardware implementado. • Un ambiente de comunicación virtual es establecido para la validación del propuesto sistema de transceptores MB-OFDM. Este método es provisto para facilitar el uso y la conveniencia de analizar el sistema digital de basebanda sin parte frontera analógica bajo diferentes ambientes de comunicación. Esta tesis doctoral está organizada en seis capítulos. En el primer capítulo se encuentra una breve introducción al campo del UWB, tanto relacionado con el proyecto como la motivación del desarrollo del sistema de MB-OFDM. En el capítulo 2, se presenta la información general y los requisitos del protocolo de comunicación inalámbrica MBOFDM UWB. En el capítulo 3 se habla de la arquitectura del sistema de transceptor digital MB-OFDM de banda base . El diseño del algoritmo propuesto y la arquitectura para cada elemento del procesamiento está detallado en este capítulo. Los retos de diseño del sistema que involucra un compromiso de discusión entre la complejidad de diseño, el consumo de energía, el coste de hardware, el desempeño del sistema, y otros aspectos. En el capítulo 4, se ha descrito la co-diseñada metodología de hardware/software. Cada parte del flujo del diseño será detallado con algunos ejemplos que se ha hecho durante el desarrollo del sistema. Aprovechando esta estrategia de diseño, el procedimiento de comunicación virtual es llevado a cabo para probar y analizar la arquitectura del transceptor propuesto. Los resultados experimentales de la co-simulación y el informe sintético de la implementación del sistema FPGA son reflejados en el capítulo 5. Finalmente, en el capítulo 6 se incluye las conclusiones y los futuros proyectos, y también los resultados derivados de este proyecto de doctorado. ABSTRACT In recent years, the Wireless Visual Sensor Network (WVSN) has drawn great interest in wireless communication research area. They enable a wealth of new applications such as building security control, image sensing, and target localization. However, nowadays wireless communication protocols (ZigBee, Wi-Fi, and Bluetooth for example) cannot fully satisfy the demands of high data rate, low power consumption, short range, and high robustness requirements. New communication protocol is highly desired for such kind of applications. The Ultra Wideband (UWB) wireless communication protocol, which has increased in importance for high data rate wireless communication field, are emerging as an important topic for WVSN research. UWB has emerged as a technology that offers great promise to satisfy the growing demand for low-cost, high-speed digital wireless indoor and home networks. The large bandwidth available, the potential for high data rate transmission, and the potential for low complexity and low power consumption, along with low implementation cost, all present a unique opportunity for UWB to become a widely adopted radio solution for future Wireless Personal Area Network (WPAN) applications. UWB is defined as any transmission that occupies a bandwidth of more than 20% of its center frequency, or more than 500 MHz. In 2002, the Federal Communications Commission (FCC) has mandated that UWB radio transmission can legally operate in the range from 3.1 to 10.6 GHz at a transmitter power of －41.3 dBm/Hz. Under the FCC guidelines, the use of UWB technology can provide enormous capacity over short communication ranges. Considering Shannon’s capacity equations, increasing the channel capacity requires linear increasing in bandwidth, whereas similar channel capacity increases would require exponential increases in transmission power. In recent years, several different UWB developments has been widely studied in different area, among which, the MB-OFDM UWB wireless communication protocol is considered to be the leading choice and has recently been adopted in the ISO/IEC standard for WPANs. By combing the OFDM modulation and data transmission using frequency hopping techniques, the MB-OFDM UWB system is able to support various data rates, ranging from 55 to 480 Mbps, over distances up to 10 meters. The MB-OFDM technology is expected to consume very little power and silicon area, as well as provide low-cost solutions that can satisfy consumer market demands. To fulfill these expectations, MB-OFDM UWB research and development have to cope with several challenges, which consist of high-sensitivity synchronization, low- complexity constraints, strict power limitations, scalability, and flexibility. Such challenges require state-of-the-art digital signal processing expertise to develop systems that could fully take advantages of the UWB spectrum and support future indoor wireless applications. This thesis focuses on fully optimization for the MB-OFDM UWB digital baseband transceiver system, aiming at researching and designing a wireless communication subsystem for the Wireless Visual Sensor Networks (WVSNs) application. The inherent high complexity of the FFT/IFFT processor and synchronization system, and high operation frequency for all processing elements, becomes the bottleneck for low power MB-OFDM based UWB digital baseband system hardware design and implementation. The proposed transceiver system targets low power and low complexity under the premise of high performance. Optimizations are made at both algorithm and architecture level for each element of the transceiver system. The low-power hardwareefficient structures are firstly proposed for those core computation modules, i.e., the mixed-radix algorithm based pipelined architecture is proposed for the Fast Fourier Transform (FFT/IFFT) processor, and the cost-speed balanced Viterbi Decoder (VD) module is developed, in the aim of lowering the power consumption and increasing the processing speed. In addition, a low complexity sign-bit correlation based symbol timing synchronization scheme is presented so as to detect and synchronize the OFDM packets robustly and accurately. Moreover, several state-of-the-art technologies are used for developing other processing subsystems and an entire MB-OFDM digital baseband transceiver system is integrated. The target device for the proposed transceiver system is Xilinx Virtex 5 XC5VLX110T FPGA board. In order to validate the proposed transceiver system in the FPGA board, a unified algorithm-architecture-circuit hardware/software co-design environment for complex FPGA system development is presented in this work. The main objective of the proposed strategy is to find an efficient methodology for designing a configurable optimized FPGA system by using as few efforts as possible in system verification procedure, so as to speed up the system development period. The presented co-design methodology has the advantages of easy to use, covering all steps from algorithm proposal to hardware verification, and widely spread for almost all kinds of FPGA developments. Because only the digital baseband transceiver system is developed in this thesis, the validation of transmitting signals through wireless channel in real communication environments still requires the analog front-end and RF components. However, by using the aforementioned hardware/software co-simulation methodology, the transmitter and receiver digital baseband systems get the opportunity to communicate with each other through the channel models, which are proposed from the IEEE 802.15.3a research group, established in MATLAB. Thus, by simply adjust the characteristics of each channel model, e.g. mean excess delay and center frequency, we can estimate the transmission performance of the proposed transceiver system through different communication situations. The main contributions of this thesis are: • A novel mixed radix 128-point FFT algorithm by using multipath pipelined architecture is proposed. The complex multipliers for each processing stage are designed by using modified shift-add architectures. The system wordlength and twiddle word-length are compared and selected based on Signal to Quantization Noise Ratio (SQNR) and power analysis. • IFFT processor performance is analyzed under different Block Floating Point (BFP) arithmetic situations for overflow control, so as to find out the perfect architecture of IFFT algorithm based on the proposed FFT processor. • An innovative low complex timing synchronization and compensation scheme, which consists of Packet Detector (PD) and Timing Offset Estimation (TOE) functions, for MB-OFDM UWB receiver system is employed. By simplifying the cross-correlation and maximum likelihood functions to signbit only, the computational complexity is significantly reduced. • A 64 state soft-decision Viterbi Decoder system by using high speed radix-4 Add-Compare-Select architecture is proposed. Two-pointer Even algorithm is also introduced into the Trace Back unit in the aim of hardware-efficiency. • Several state-of-the-art technologies are integrated into the complete baseband transceiver system, in the aim of implementing a highly-optimized UWB communication system. • An improved design flow is proposed for complex system implementation which can be used for general Field-Programmable Gate Array (FPGA) designs. The design method not only dramatically reduces the time for functional verification, but also provides automatic analysis such as errors and output delays for the implemented hardware systems. • A virtual communication environment is established for validating the proposed MB-OFDM transceiver system. This methodology is proved to be easy for usage and convenient for analyzing the digital baseband system without analog frontend under different communication environments. This PhD thesis is organized in six chapters. In the chapter 1 a brief introduction to the UWB field, as well as the related work, is done, along with the motivation of MBOFDM system development. In the chapter 2, the general information and requirement of MB-OFDM UWB wireless communication protocol is presented. In the chapter 3, the architecture of the MB-OFDM digital baseband transceiver system is presented. The design of the proposed algorithm and architecture for each processing element is detailed in this chapter. Design challenges of such system involve trade-off discussions among design complexity, power consumption, hardware cost, system performance, and some other aspects. All these factors are analyzed and discussed. In the chapter 4, the hardware/software co-design methodology is proposed. Each step of this design flow will be detailed by taking some examples that we met during system development. Then, taking advantages of this design strategy, the Virtual Communication procedure is carried out so as to test and analyze the proposed transceiver architecture. Experimental results from the co-simulation and synthesis report of the implemented FPGA system are given in the chapter 5. The chapter 6 includes conclusions and future work, as well as the results derived from this PhD work.

Adapting a speech into sign language translation system to a new domain

This paper presents a methodology for adapting an advanced communication system for deaf people in a new domain. This methodology is a user-centered design approach consisting of four main steps: requirement analysis, parallel corpus generation, technology adaptation to the new domain, and finally, system evaluation. In this paper, the new considered domain has been the dialogues in a hotel reception. With this methodology, it was possible to develop the system in a few months, obtaining very good performance: good speech recognition and translation rates (around 90%) with small processing times.

Modelo Híbrido para la Ayuda al Capitán

En esta Tesis se plantea una nueva forma de entender la evacuación apoyándonos en tecnologías existentes y accesibles que nos permitirán ver este proceso como un ente dinámico. Se trata de una metodología que implica no solo el uso de herramientas de análisis que permitan la definición de planes de evacuación en tiempo real, sino que también se apunta hacia la creación de una infraestructura física que permita alimentar con información actualizada al sistema de forma que, según la situación y la evolución de la emergencia, sea posible realizar planes alternativos que se adapten a las nuevas circunstancias. En base a esto, el sistema asimilará toda esa información y aportará soluciones que faciliten la toma de decisiones durante toda la evolución del incidente. Las aportaciones originales de esta Tesis son múltiples y muy variadas, pudiéndolas resumir en los siguientes puntos: 1. Estudio completo del estado del arte: a. Detección y análisis de diferentes proyectos a nivel internacional que de forma parcial tratan algunos aspectos desarrollados en la Tesis. b. Completo estudio a nivel mundial del software desarrollado total o parcialmente para la simulación del comportamiento humano y análisis de procesos de evacuación. Se ha generado una base de datos que cataloga de forma exhaustiva estas aplicaciones, permitiendo realizar un completo análisis y posibilitando la evolución futura de los contenidos de la misma. En la tesis se han analizado casi un centenar de desarrollos, pero el objetivo es seguir completando esta base de datos debido a la gran utilidad y a las importantes posibilidades que ofrece. 2. Desarrollo de un importante capítulo que trata sobre la posibilidad de utilizar entornos virtuales como alternativa intermedia al uso de simuladores y simulacros. En esta sección se divide en dos bloques: a. Ensayos en entornos reales y virtuales. b. Ensayos en entornos virtuales (pruebas realizadas con varios entornos virtuales). 3. Desarrollo de e-Flow net design: paquete de herramientas desarrolladas sobre Rhinoceros para el diseño de la red de evacuación basada en los elementos definidos en la tesis: Nodes, paths, Relations y Areas. 4. Desarrollo de e-Flow Simulator: Conjunto de herramientas que transforman Rhinoceros en un simulador 3D de comportamiento humano. Este simulador, de desarrollo propio, incorpora un novedoso algoritmo de comportamiento a nivel de individuo que incluye aspectos que no se han encontrado en otros simuladores. Esta herramienta permite realizar simulaciones programadas de grupos de individuos cuyo comportamiento se basa en el análisis del entorno y en la presencia de referencias dinámicas. Incluye otras importantes novedades como por ejemplo: herramientas para análisis de la señalización, elementos de señalización dinámica, incorporación sencilla de obstáculos, etc. También se ha creado una herramienta que posibilita la implementación del movimiento del propio escenario simulando la oscilación del mismo, con objeto de reflejar la influencia del movimiento del buque en el desplazamiento de los individuos. 5. En una fase avanzada del desarrollo, se incorporó la posibilidad de generar un vídeo de toda la simulación, momento a partir del cual, se han documentado todas las pruebas (y se continúan documentando) en una base de datos que recoge todas las características de las simulaciones, los problemas detectados, etc. Estas pruebas constituyen, en el momento en que se ha cerrado la redacción de la Tesis, un total de 81 GB de datos. Generación y análisis de rutas en base a la red de evacuación creada con e-Flow Net design y las simulaciones realizadas con e-Flow Net simulator. a. Análisis para la optimización de la configuración de la red en base a los nodos por área existentes. b. Definición de procesos previos al cálculo de rutas posibles. c. Cálculo de rutas: i. Análisis de los diferentes algoritmos que existen en la actualidad para la optimización de rutas. ii. Desarrollo de una nueva familia de algoritmos que he denominado “Minimum Decision Algorithm (MDA)”, siendo los algoritmos que componen esta familia: 1. MDA básico. 2. MDA mínimo. 3. MDA de no interferencia espacial. 4. MDA de expansión. 5. MDA de expansión ordenada para un único origen. 6. MDA de expansión ordenada. iii. Todos estos algoritmos se han implementado en la aplicación e-Flow creada en la Tesis para el análisis de rutas y que constituye el núcleo del Sistema de Ayuda al Capitán. d. Determinación de las alternativas para el plan de evacuación. Tras la definición de las rutas posibles, se describen diferentes procesos existentes de análisis por ponderación en base a criterios, para pasar finalmente a definir el método de desarrollo propio propuesto en esta Tesis y cuyo objetivo es responder en base a la población de rutas posibles obtenidas mediante los algoritmos MDA, qué combinación de rutas constituyen el Plan o Planes más adecuados para cada situación. La metodología creada para la selección de combinaciones de rutas que determinan un Plan completo, se basa en cuatro criterios básicos que tras su aplicación ofrecen las mejores alternativas. En esta fase también se incluye un complejo análisis de evolución temporal que incorpora novedosas definiciones y formulaciones. e. Derivado de la definición de la metodología creada en esta Tesis para la realización de los análisis de evolución temporal, se ha podido definir un nuevo teorema matemático que se ha bautizado como “Familia de cuadriláteros de área constante”. 7. Especificación de la infraestructura física del Sistema de Ayuda al Capitán: parte fundamental de sistema es la infraestructura física sobre la que se sustentaría. Esta infraestructura estaría compuesta por sensores, actuadores, aplicaciones para dispositivos móviles, etc. En este capítulo se analizan los diferentes elementos que la constituirían y las tecnologías implicadas. 8. Especificación de la infraestructura de servicios. 9. Creación del Blog Virtual Environments (http://epcinnova-virtualenvironments.blogspot.com.es/) en el que se han publicado todas las pruebas realizadas en el capítulo que analiza los entornos virtuales como alternativa a los simuladores y a los ensayos en laboratorio o los simulacros, incluyendo en muchos casos la posibilidad de que el visitante del blog pueda realizar la simulación en el entorno virtual. Este blog también incluye otras secciones que se han trabajado durante la Tesis: • Recopilación de diferentes entornos virtuales existentes. • Diagrama que recopila información sobre accidentes tanto en el ámbito marítimo como en el terrestre (en desarrollo). • Esquema propuesto para el acopio de información obtenida a partir de un simulacro. 10. Esta Tesis es la base para el proyecto e-Flow (nombre de una de las aplicaciones que desarrolladas en esta obra), un proyecto en el que el autor de esta Tesis ha trabajado como Project Manager. En el proyecto participa un consorcio de empresas y la UPM, y tiene como objetivo trasladar a la realidad gran parte de los planteamientos e ideas presentadas en esta Tesis. Este proyecto incluye el desarrollo de la infraestructura física y de servicios que permitirán, entre otras cosas, implementar en infraestructuras complejas una plataforma que posibilita la evacuación dinámica y un control ubicuo de los sistemas de monitorización y actuación implementados. En estos momentos se está finalizando el proyecto, cuyo objetivo final es la implementación de un piloto en un Hospital. También destacamos los siguientes avances a nivel de difusión científico-tecnológico: • Ponencia en el “52 congreso de la Ingeniería Naval en España” presentando un artículo “e-Flow- Sistema integral inteligente de soporte a la evacuación”. En este artículo se trata tanto el proyecto e-Flow del que soy Project Manager, como esta Tesis Doctoral, al ser temas estrechamente vinculados. En 2014 se publicó en dos números de la Revista Ingeniería Naval el artículo presentado a estas jornadas. • Co-autor en el artículo “E-Flow: A communication system for user notification in dynamic evacuation scenarios” presentado en el 7th International Conference on Ubicuous Computing & Ambient Intelligence (UCAMI) celebrado en Costa Rica. Por último, una de las aportaciones más interesantes, es la definición de un gran número de líneas de investigación futuras en base a todos los avances realizados en esta Tesis. ABSTRACT With this Thesis a new approach for understanding evacuation process is considered, taking advantage of the existing and open technologies that will allow this process to be interpreted as a dynamic entity. The methodology involves not only tools that allows on.-time evacuation plans, but also creates a physical insfrastructure that makes possible to feed the system with information on real time so, considering in each moment the real situation as well as the specific emergency development it will be feasible to generate alternative plans that responds to the current emergency situation. In this respect, the system will store all this information and will feedback with solutions that will help the decision making along the evacuation process. The innovative and singular contributions of this Thesis are numerous and rich, summarised as follows: 1.- Complete state-of-art study: a. Detection and analysis of different projects on an international level that, although partially, deal with some aspects developed in this Thesis. b. Thorough study at a international level of the developed software - total or partially done - for the simulation of the human behaviour and evacuation processes analysis. A database has been generated that classifies in detail these applications allowing to perform a full analysis and leading to future evolution of its contents. Within the Thesis work, almost a hundred of developments have been analysed but the purpose is to keep up updating this database due to the broad applications and possibilities that it involves. 2. Development of an important chapter that studies the possibility of using virtual scenarios as mid-term alternative for the use of simulations. This section is divided in two blocks: a. Trials in virtual and real scenarios b. Trials in virutal scenarios (trials performed with several ones). 3. E-Flow net design development: Set of tools developed under Rhinoceros for the evacuation net design based on the elements defined in the Thesis: Nodes, Paths, Relations, Areas 4. E-Flow simulator development: Set of tools that uses Rhinoceros as a 3D simulator of human behaviour. This simulator, of my own design, includes a new and original algorithm of human behaviour that involves aspects that are not found in other simulators. This tool allows to perform groups programmed simulations which behaviour is based on their enviroment analysis and presence of dynamic references. It includes other important innovations as for example: tools for signals analysis, dynamic signal elements, easy obstacle adding etc... More over, a tool that allows the own scenario movement implementation has been created by simulating the own oscillation movement, with the purpose of playing the vessel movement's influences in the individuals' displacements. 5. In an advanced stage of the development, the possibility of generating a video recording of all the simulation was also integrated, then from that moment all tests have been filed (and keep on doing so) in a database that collects all simulation characteristics, failures detected, etc. These stored tests amounts to a total of 81 GB at the moment of finishing the Thesis work. Generation and analysis of paths regarding the evacuation net created with E-Flow design and the simulations performed with E-Flow net Simulator. a. Analysis for the optimisation of the network configuration based in the existing nodes per area. b. Definition of the processes previous to the calculation of the feasible paths c. Paths calculation: i. Analysis of the different algorithms on existance nowadays for the routes optimisation. ii. Development of a new family of algorithms that I have called “Minimum Decision Algorithm (MDA)”, being composed of: 1. MDA basic 2. MDA minimum 3. MDA of not spacial interference 4. MDA of expansion (es de extenderse) o enlargement ( es de crecimiento) 5. MDA of organised expansion for a single origin (of organised enlargement for a single origin) 6. MDA of organised expansion (of organised enlargement) iii. All these algorithms have been implemented in the E-Flow application created in the Thesis dfor the routes analysis and it is the core of the Captain's support system. d. Determination of the alternatives for the evacuation plan. After defining all possible paths, different processes of analysis existing for weighing-based criteria are described, thus to end defining the own development method proposed in this Thesis and that aims to respond in an agreggation of possible routes basis obtained by means of the MDA algorithms what is the routes' combination more suitable for the Plan or Plans in every situation. The methodology created fot the selection of the combinations of routes that determine a complete Plan is baesd in four basic criteria that after applying, offer the best alternatives. In this stage a complex analysis of the progress along time is also included, that adds original and innovative defintions and formulations. e. Originated from the methodology created in this Thesis for the perfoming of the analysy of the progress along time, a new mathematic theorem has been defined, that has been called as "Family of quadrilateral of constant area". 7. Specification of the physiscal infrastructure of the Captain's help system: essential part is this physical infrastructure that will support it. This system will be made of sensors, actuators, apps for mobile devices etc... Within this chapter the different elements and technologies that make up this infrastructure will be studied. 8. Specification for the services infrastructure. 9. Start up of the Blog. " Virtual Environments (http://epcinnova-virtualenvironments.blogspot.com.es/)" in which all tests performed have been published in terms of analysis of the virtual enviroments as alternative to the simulators as well as to the laboratory experiments or simulations, including in most of the cases the possibility that the visitor can perform the simulation within the virtual enviroment. This blog also includes other sections that have been worked along and within this Thesis: - Collection of different virtual scenarios existent. - Schema that gathers information concerning accidents for maritime and terrestrial areas (under development) - Schema proposed for the collecting of information obtained from a simulation. 10. This Thesis is the basis of the E-Flow project (name of one of the applications developed in this work), a project in which the Thesis' author has worked in as Project Manager. In the project takes part a consortium of firms as well as the UPM and the aim is to bring to real life most part of the approaches and ideas contained in this Thesis. This project includes the development of the physical infrastructure as well as the services that will allow, among others, implement in complex infrastrucutres a platform that will make possible a dynamic evacuation and a continuous control of the monitoring and acting systems implemented. At the moment the project is getting to an end which goal is the implementation of a pilot project in a Hospital. We also would like to highlight the following advances concerning the scientific-technology divulgation: • Talk in the " 52th Congress of the Naval Engineering in Spain" with the article "E-Flow . Intelligent system integrated for supporting evacuation". This paper is about project E-Flow which I am Project Manager of, as well as this Thesis for the Doctorate, being both closely related. Two papers published In 2014 in the Naval Engineering Magazine. • Co-author in the article “E-Flow: A communication system for user notification in dynamic evacuation scenarios” [17] introduced in the 7th International Conference on Ubicuous Computing & Ambient Intelligence (UCAMI) held in Costa Rica. Last, but not least, one of the more interesting contributions is the defintion of several lines of research in the future, based on the advances made in this Thesis.

Folliculostellate cell network: A route for long-distance communication in the anterior pituitary

All higher life forms critically depend on hormones being rhythmically released by the anterior pituitary. The proper functioning of this master gland is dynamically controlled by a complex set of regulatory mechanisms that ultimately determine the fine tuning of the excitable endocrine cells, all of them heterogeneously distributed throughout the gland. Here, we provide evidence for an intrapituitary communication system by which information is transferred via the network of nonendocrine folliculostellate (FS) cells. Local electrical stimulation of FS cells in acute pituitary slices triggered cytosolic calcium waves, which propagated to other FS cells by signaling through gap junctions. Calcium wave initiation was because of the membrane excitability of FS cells, hitherto classified as silent cells. FS cell coupling could relay information between opposite regions of the gland. Because FS cells respond to central and peripheral stimuli and dialogue with endocrine cells, the form of large-scale intrapituitary communication described here may provide an efficient mechanism that orchestrates anterior pituitary functioning in response to physiological needs.

Proceedings of the fifth International Mobile Satellite Conference 1997, IMSC '97 : Pasadena, CA, June 16-18, 1997 /

Mode of access: Internet.

Effect of line of sight propagation on capacity of an indoor MIMO system

In this paper the performance of a multiple input multiple output (MIMO) wireless communication system operating in an indoor environment, featuring both line of sight (LOS) and non-line of sight (NLOS) signal propagation, is assessed. In the model the scattering objects are assumed to be uniformly distributed in an area surrounding the transmitting and receiving array antennas. Mutual coupling effects in the arrays are treated in an exact manner. However interactions with scattering objects are taken into account via a single bounce approach. Computer simulations are carried out for the system capacity for varying inter-element spacing in the receiving array for assumed values of LOS/NLOS power fraction and signal to noise ratio (SNR).

Advanced receivers for next generation wireless communication systems

Despite extensive progress on the theoretical aspects of spectral efficient communication systems, hardware impairments, such as phase noise, are the key bottlenecks in next generation wireless communication systems. The presence of non-ideal oscillators at the transceiver introduces time varying phase noise and degrades the performance of the communication system. Significant research literature focuses on joint synchronization and decoding based on joint posterior distribution, which incorporate both the channel and code graph. These joint synchronization and decoding approaches operate on well designed sum-product algorithms, which involves calculating probabilistic messages iteratively passed between the channel statistical information and decoding information. Channel statistical information, generally entails a high computational complexity because its probabilistic model may involve continuous random variables. The detailed knowledge about the channel statistics for these algorithms make them an inadequate choice for real world applications due to power and computational limitations. In this thesis, novel phase estimation strategies are proposed, in which soft decision-directed iterative receivers for a separate A Posteriori Probability (APP)-based synchronization and decoding are proposed. These algorithms do not require any a priori statistical characterization of the phase noise process. The proposed approach relies on a Maximum A Posteriori (MAP)-based algorithm to perform phase noise estimation and does not depend on the considered modulation/coding scheme as it only exploits the APPs of the transmitted symbols. Different variants of APP-based phase estimation are considered. The proposed algorithm has significantly lower computational complexity with respect to joint synchronization/decoding approaches at the cost of slight performance degradation. With the aim to improve the robustness of the iterative receiver, we derive a new system model for an oversampled (more than one sample per symbol interval) phase noise channel. We extend the separate APP-based synchronization and decoding algorithm to a multi-sample receiver, which exploits the received information from the channel by exchanging the information in an iterative fashion to achieve robust convergence. Two algorithms based on sliding block-wise processing with soft ISI cancellation and detection are proposed, based on the use of reliable information from the channel decoder. Dually polarized systems provide a cost-and spatial-effective solution to increase spectral efficiency and are competitive candidates for next generation wireless communication systems. A novel soft decision-directed iterative receiver, for separate APP-based synchronization and decoding, is proposed. This algorithm relies on an Minimum Mean Square Error (MMSE)-based cancellation of the cross polarization interference (XPI) followed by phase estimation on the polarization of interest. This iterative receiver structure is motivated from Master/Slave Phase Estimation (M/S-PE), where M-PE corresponds to the polarization of interest. The operational principle of a M/S-PE block is to improve the phase tracking performance of both polarization branches: more precisely, the M-PE block tracks the co-polar phase and the S-PE block reduces the residual phase error on the cross-polar branch. Two variants of MMSE-based phase estimation are considered; BW and PLP.

Understanding mobile phone usage while driving:mini-bus and taxi drivers' experiences in Istanbul

In emerging markets, the amount of mobile communication and the number of occasions mobile phones are used are increasing. More and more settings appropriate or not for mobile phone usage are being exposed. Although prohibited by many governments, there is evidence that use of new mobile devices while driving are somehow becoming current everyday practice, hence legitimatizing usage for many users. Dominant dangerous behavior in the absence of enforced legal framework is being deployed and has become routine for many m-users. This chapter adopts a qualitative case study approach (20 cases) to examine the public transport drivers' motives, logic and legitimacy processes. The question which these issues raise in the light of advancing m-technologies is: How do, in the context of emerging market, undesired emerging routines enactment get to be reflected upon and voluntarily disregarded to maximize the benefits of m-technologies while minimizing their drawbacks? Findings point out at multiple motives for usage including external social pressure through the ubiquitous 24/7 usage of mtechnology, lack of alternative communication protocol, real time need for action and from an internal perspectives boredoms, lack of danger awareness, blurring of the boundaries between personal and business life and lack of job fulfillment are uncovered as key factors. As secondary dynamic factors such as education, drivers work' histories, impunity, lack of strong consumer opposition appear central in shaping the development of the routines. © 2011, IGI Global.

Fibre-based devices for next generation photonics communication systems

The future broadband information network will undoubtedly integrate the mobility and flexibility of wireless access systems with the huge bandwidth capacity of photonics solutions to enable a communication system capable of handling the anticipated demand for interactive services. Towards wide coverage and low cost implementations of such broadband wireless photonics communication networks, various aspects of the enabling technologies are continuingly generating intense research interest. Among the core technologies, the optical generation and distribution of radio frequency signals over fibres, and the fibre optic signal processing of optical and radio frequency signals, have been the subjects for study in this thesis. Based on the intrinsic properties of single-mode optical fibres, and in conjunction with the concepts of optical fibre delay line filters and fibre Bragg gratings, a number of novel fibre-based devices, potentially suitable for applications in the future wireless photonics communication systems, have been realised. Special single-mode fibres, namely, the high birefringence (Hi-Bi) fibre and the Er/Yb doped fibre have been employed so as to exploit their merits to achieve practical and cost-effective all-fibre architectures. A number of fibre-based complex signal processors for optical and radio frequencies using novel Hi-Bi fibre delay line filter architectures have been illustrated. In particular, operations such as multichannel flattop bandpass filtering, simultaneous complementary outputs and bidirectional nonreciprocal wavelength interleaving, have been demonstrated. The proposed configurations featured greatly reduced environmental sensitivity typical of coherent fibre delay line filter schemes, reconfigurable transfer functions, negligible chromatic dispersions, and ease of implementation, not easily achievable based on other techniques. A number of unique fibre grating devices for signal filtering and fibre laser applications have been realised. The concept of the superimposed fibre Bragg gratings has been extended to non-uniform grating structures and into Hi-Bi fibres to achieve highly useful grating devices such as overwritten phase-shifted fibre grating structure and widely/narrowly spaced polarization-discriminating filters that are not limited by the intrinsic fibre properties. In terms of the-fibre-based optical millimetre wave transmitters, unique approaches based on fibre laser configurations have been proposed and demonstrated. The ability of the dual-mode distributed feedback (DFB) fibre lasers to generate high spectral purity, narrow linewidth heterodyne signals without complex feedback mechanisms has been illustrated. A novel co-located dual DFB fibre laser configuration, based on the proposed superimposed phase-shifted fibre grating structure, has been further realised with highly desired operation characteristics without the need for costly high frequency synthesizers and complex feedback controls. Lastly, a novel cavity mode condition monitoring and optimisation scheme for short length, linear-cavity fibre lasers has been proposed and achieved. Based on the concept and simplicity of the superimposed fibre laser cavities structure, in conjunction with feedback controls, enhanced output performances from the fibre lasers have been achieved. The importance of such cavity mode assessment and feedback control for optimised fibre laser output performance has been illustrated.

Transmission of data under multipath transmission conditions

The explosive growth in microprocessor technology and the increasing use of computers to store information has increased the demand for data communication channels. Because of this, data communication to mobile vehicles is increasing rapidly. In addition, data communication is seen as a method of relieving the current congestion of mobile radio telephone bands in the U.K. Highly reliable data communication over mobile radio channels is particularly difficult to achieve, primarily due to fading caused by multipath interference. In this thesis a data communication system is described for use over radio channels impaired by multipath interference. The thesis first describes radio communication in general, and multipath interference In particular. The practical aspects of fading channels are stressed because of their importance in the development of the system. The current U.K. land mobile radio scene is then reviewed, with particular emphasis on the use of existing mobile radio equipment for data communication purposes. The development of the data communication system is then described. This system is microprocessor based and uses an advanced form of automatic request repeat (ARQ) operation. It can be configured to use either existing radio-telephone equipment, totally new equipment specifically designed for data communication, or any combination of the two. Due to its adaptability, the system can automatically optimise itself for use over any channel, even if the channel parameters are changing rapidly. Results obtained from a particular implementation of the system, which is described in full, are presented. These show how the operation of the system has to change to accomodate changes in the channel. Comparisons are made between the practical results and the theoretical limits of the system.