Generation of nitrogen functionalities on activated carbons by amidation reactions and Hofmann rearrangement: Chemical and electrochemical characterization

Nitrogen functionalization of a highly microporous activated carbon (BET surface area higher than 3000 m2/g) has been achieved using the following sequence of treatments: (i) chemical oxidation using concentrated nitric acid, (ii) amidation by acyl chloride substitution with NH4NO3 and (iii) amination by Hoffman rearrangement. This reaction pathway yielded amide and amine functional groups, and a total nitrogen content higher than 3 at.%. It is achieved producing only a small decrease (20%) of the starting microporosity, being most of it related to the initial wet oxidation of the activated carbon. Remarkably, nitrogen aromatic rings were also formed as a consequence of secondary cyclation reactions. The controlled step-by-step modification of the surface chemistry allowed to assess the influence of individual nitrogen surface groups in the electrochemical performance in 1 M H2SO4 of the carbon materials. The largest gravimetric capacitance was registered for the pristine activated carbon due to its largest apparent surface area. The nitrogen-containing activated carbons showed the highest surface capacitances. Interestingly, the amidated activated carbon showed the superior capacitance retention due to the presence of functional groups (such as lactams, imides and pyrroles) that enhance electrical conductivity through their electron-donating properties, showing a capacitance of 83 F/g at 50 A/g.

Bio-based PLA_PHB plasticized blend films: Processing and structural characterization

Bio-based films formed by poly(lactic acid) (PLA) and poly(3-hydroxybutyrate) (PHB) plasticized with an oligomer of the lactic acid (OLA) were used as supporting matrices for an antibacterial agent (carvacrol). This paper reports the main features of the processing and physico-chemical characterization of these innovative biodegradable material based films, which were extruded and further submitted to filmature process. The effect of the addition of carvacrol and OLA on their microstructure, chemical, thermal and mechanical properties was assessed. The presence of these additives did not affect the thermal stability of PLA_PHB films, but resulted in a decrease in their crystallinity and in the elastic modulus for the active formulations. The obtained results showed the effective presence of additives in the PLA or the PLA_PHB matrix after processing at high temperatures, making them able to be used in active and bio-based formulations with antioxidant/antimicrobial performance.

Development of a Mechanism and Process to Continuously Produce Spherical, Torrefied Biomass

Thesis (Master, Mechanical and Materials Engineering) -- Queen's University, 2016-06-17 02:15:25.215

A method for presentation of cost estimates and process economics as recommended by the Atomic Energy Commission /

"July 26, 1956."

Mesoporous bioactive glasses. I. Synthesis and structural characterization

Highly ordered mesoporous bioactive glasses (MBGs) with different compositions have been synthesized by a combination of surfactant templating, sol-gel method and evaporation-induced self-assembly (EISA) processes. The texture properties and compositional homogeneity of MBGs have been characterized and compared with conventional bioactive glasses (BGs) synthesized in the absence of surfactants by evaporation method. The formation mechanism (pore - composition dependence) and compositional homogeneity in the case of MBG materials are different from those in conventional BGs. Unlike conventional sol-gel-derived BGs that shows a direct correlation between their composition and pore architecture, MBGs with different compositions may possess similar pore volume and uniformly distributed pore size when the same structure-directing agent is utilized. The framework of MBG is homogeneously distributed in composition at the nanoscale and the inorganic species generally exists in the form of amorphous phase. MBGs calcined at temperatures

Formulation and process engineering of freeze-dried orally disintegrating tablets

Orally disintegrating tablets (ODTs) which are also referred to as orodispersible and fast disintegrating tablets, are solid oral dosage forms which upon placing on the tongue, disperse/disintegrate rapidly before being swallowed as a suspension or solution. ODTs are therefore easier and more convenient to administer than conventional tablets and are particularly beneficial for paediatric and geriatric patients, who generally have difficulty swallowing their medication. The work presented in this thesis involved the formulation and process development of ODTs, prepared using freeze-drying. Gelatin is one of the principal excipients used in the formulation of freeze-dried ODTs. One of the studies presented in this thesis investigated the potential modification of the properties of this excipient, in order to improve the performance of the tablets. As gelatin is derived from animal sources, a number of ethical issues surround its use as an excipient in pharmaceutical preparations. This was one of the motivations, Methocel™ and Kollicoat® IR were evaluated as binders as alternative materials to gelatin. Polyox™ was also evaluated as a binder together with its potential uses as a viscosity increasing and mucoadhesive agent to increase the retention of tablets in the mouth to encourage pre-gastric absorption of active pharmaceutical ingredients (APIs). The in vitro oral retention of freeze-dried ODT formulations was one property which was assessed in a design of experiments – factorial design study, which was carried out to further understand the role that formulation excipients have on the properties of the tablets. Finally, the novel approach of incorporating polymeric nanoparticles in freeze-dried ODTs was investigated, to study if the release profile of APIs could be modified, which could improve their therapeutic effect. The results from these studies demonstrated that the properties of gelatin-based formulations can be modified by adjusting pH and ionic strength. Adjustment of formulation pH has shown to significantly reduce tablet disintegration time. Evaluating Methocel™, in particular low viscosity grades, and Kollicoat® IR as binders has shown that these polymers can form tablets of satisfactory hardness and disintegration time. Investigating Polyox™ as an excipient in freeze-dried ODT formulations revealed that low viscosity grades appear suitable as binders whilst higher viscosity grades could potentially be utilised as viscosity increasing and mucoadhesive agents. The design of experiments – factorial design study revealed the influence of individual excipients in a formulation mix on resultant tablet properties and in vitro oral retention of APIs. Novel methods have been developed, which allows the incorporation of polymeric nanoparticles in situ in freeze-dried ODT formulations, which allows the modification of the release profile of APIs.

DEVELOPMENT OF A MECHANISM AND PROCESS TO CONTINUOUSLY PRODUCE SPHERICAL, TORREFIED BIOMASS PELLETS

A recently developed novel biomass fuel pellet, the Q’ Pellet, offers significant improvements over conventional white pellets, with characteristics comparable to those of coal. The Q’ Pellet was initially created at bench scale using a proprietary die and punch design, in which the biomass was torrefied in-situ¬ and then compressed. To bring the benefits of the Q’ Pellet to a commercial level, it must be capable of being produced in a continuous process at a competitive cost. A prototype machine was previously constructed in a first effort to assess continuous processing of the Q’ Pellet. The prototype torrefied biomass in a separate, ex-situ reactor and transported it into a rotary compression stage. Upon evaluation, parts of the prototype were found to be unsuccessful and required a redesign of the material transport method as well as the compression mechanism. A process was developed in which material was torrefied ex-situ and extruded in a pre-compression stage. The extruded biomass overcame multiple handling issues that had been experienced with un-densified biomass, facilitating efficient material transport. Biomass was extruded directly into a novel re-designed pelletizing die, which incorporated a removable cap, ejection pin and a die spring to accommodate a repeatable continuous process. Although after several uses the die required manual intervention due to minor design and manufacturing quality limitations, the system clearly demonstrated the capability of producing the Q’ Pellet in a continuous process. Q’ Pellets produced by the pre-compression method and pelletized in the re-designed die had an average dry basis gross calorific value of 22.04 MJ/kg, pellet durability index of 99.86% and dried to 6.2% of its initial mass following 24 hours submerged in water. This compares well with literature results of 21.29 MJ/kg, 100% pellet durability index and <5% mass increase in a water submersion test. These results indicate that the methods developed herein are capable of producing Q’ Pellets in a continuous process with fuel properties competitive with coal.

Radiological and material characterization of high volume fly ash concrete

The main goal of research presented in this paper was the material and radiological characterization of high volume fly ash concrete (HVFAC) in terms of determination of natural radionuclide content and radon emanation and exhalation coefficients. All concrete samples were made with a fly ash content between 50% and 70% of the total amount of cementitious materials from one coal burning power plant in Serbia. Physical (fresh and hardened concrete density) and mechanical properties (compressive strength, splitting tensile strength and modulus of elasticity) of concrete were tested. The radionuclide content (226Ra, 232Th and 40K) and radon massic exhalation of HVFAC samples were determined using gamma spectrometry. Determination of massic exhalation rates of HVFAC and its components using radon accumulation chamber techniques combined with a radon monitor was performed. The results show a beneficial effect of pozzolanic activity since the increase in fly ash content resulted in an increase in compressive strength of HVFAC by approximately 20% for the same mass of cement used in the mixtures. On the basis of the obtained radionuclide content of concrete components the I -indices of different HVFAC samples were calculated and compared with measured values (0.27e0.32), which were significantly below the recommended 1.0 index value. The prediction was relatively close to the measured values as the ratio between the calculated and measured I-index ranged between 0.89 and 1.14. Collected results of mechanical and radiological properties and performed calculations clearly prove that all 10 designed concretes with a certain type of fly ash are suitable for structural and non-structural applications both from a material and radiological point of view.

Relational and reproductive trajectories leading to adolescent pregnancy in Portugal: a national and regional characterization

INTRODUCTION: The current study aimed to describe the relational and reproductive trajectories leading to adolescent pregnancy in Portugal, and to explore whether there were differences in this process according to adolescents' place of residence. MATERIAL AND METHODS: Data were collected between 2008 and 2013 in 42 public health services using a self-report questionnaire developed by the researchers. The sample consisted of a nationally representative group of pregnant adolescents (n = 459). RESULTS: Regardless of having had one (59.91%) or multiple sexual partners (40.09%), the majority of adolescents became pregnant in a romantic relationship, using contraception at the time of the conception and knowing the contraceptive failure which led to pregnancy (39.22%). In some regions other trajectories were highly prevalent, reflecting options such as planning the pregnancy (Alentejo Region/ Azores Islands), not using contraception (Centro Region/Madeira Islands) or using it incorrectly, without identifying the contraceptive failure (Madeira Islands). On average, romantic relationships were longer than 19 months and adolescents' partners were older than themselves (> 4 years) and no longer in school (75.16%); these results were particularly significant when the pregnancy was planned. DISCUSSION: The knowledge gained in this study shows that prevention efforts must be targeted according to the adolescents' needs in each region and should include high-risk male groups. CONCLUSION: Our results may enable more efficient health policies to prevent adolescent pregnancy in different country regions and support educators and health care providers on sexual education and family planning efforts.

DESIGN, FABRICATION, AND PERFORMANCE CHARACTERIZATION OF MULTIFUNCTIONAL STRUCTURES TO HARVEST SOLAR ENERGY FOR FLAPPING WING AERIAL VEHICLES

Flapping Wing Aerial Vehicles (FWAVs) have the capability to combine the benefits of both fixed wing vehicles and rotary vehicles. However, flight time is limited due to limited on-board energy storage capacity. For most Unmanned Aerial Vehicle (UAV) operators, frequent recharging of the batteries is not ideal due to lack of nearby electrical outlets. This imposes serious limitations on FWAV flights. The approach taken to extend the flight time of UAVs was to integrate photovoltaic solar cells onto different structures of the vehicle to harvest and use energy from the sun. Integration of the solar cells can greatly improve the energy capacity of an UAV; however, this integration does effect the performance of the UAV and especially FWAVs. The integration of solar cells affects the ability of the vehicle to produce the aerodynamic forces necessary to maintain flight. This PhD dissertation characterizes the effects of solar cell integration on the performance of a FWAV. Robo Raven, a recently developed FWAV, is used as the platform for this work. An additive manufacturing technique was developed to integrate photovoltaic solar cells into the wing and tail structures of the vehicle. An approach to characterizing the effects of solar cell integration to the wings, tail, and body of the UAV is also described. This approach includes measurement of aerodynamic forces generated by the vehicle and measurements of the wing shape during the flapping cycle using Digital Image Correlation. Various changes to wing, body, and tail design are investigated and changes in performance for each design are measured. The electrical performance from the solar cells is also characterized. A new multifunctional performance model was formulated that describes how integration of solar cells influences the flight performance. Aerodynamic models were developed to describe effects of solar cell integration force production and performance of the FWAV. Thus, performance changes can be predicted depending on changes in design. Sensing capabilities of the solar cells were also discovered and correlated to the deformation of the wing. This demonstrated that the solar cells were capable of: (1) Lightweight and flexible structure to generate aerodynamic forces, (2) Energy harvesting to extend operational time and autonomy, (3) Sensing of an aerodynamic force associated with wing deformation. Finally, different flexible photovoltaic materials with higher efficiencies are investigated, which enable the multifunctional wings to provide enough solar power to keep the FWAV aloft without batteries as long as there is enough sunlight to power the vehicle.

Relational and reproductive trajectories leading to adolescent pregnancy in Portugal: a national and regional characterization

INTRODUCTION: The current study aimed to describe the relational and reproductive trajectories leading to adolescent pregnancy in Portugal, and to explore whether there were differences in this process according to adolescents' place of residence. MATERIAL AND METHODS: Data were collected between 2008 and 2013 in 42 public health services using a self-report questionnaire developed by the researchers. The sample consisted of a nationally representative group of pregnant adolescents (n = 459). RESULTS: Regardless of having had one (59.91%) or multiple sexual partners (40.09%), the majority of adolescents became pregnant in a romantic relationship, using contraception at the time of the conception and knowing the contraceptive failure which led to pregnancy (39.22%). In some regions other trajectories were highly prevalent, reflecting options such as planning the pregnancy (Alentejo Region/ Azores Islands), not using contraception (Centro Region/Madeira Islands) or using it incorrectly, without identifying the contraceptive failure (Madeira Islands). On average, romantic relationships were longer than 19 months and adolescents' partners were older than themselves (> 4 years) and no longer in school (75.16%); these results were particularly significant when the pregnancy was planned. DISCUSSION: The knowledge gained in this study shows that prevention efforts must be targeted according to the adolescents' needs in each region and should include high-risk male groups. CONCLUSION: Our results may enable more efficient health policies to prevent adolescent pregnancy in different country regions and support educators and health care providers on sexual education and family planning efforts.

Bioconversion of agro-industrial wastes for the production of fibrinolytic enzyme from Bacillus halodurans IND18: Purification and biochemical characterization

Background: Agro-wastes were used for the production of fibrinolytic enzyme in solid-state fermentation. The process parameters were optimized to enhance the production of fibrinolytic enzyme from Bacillus halodurans IND18 by statistical approach. The fibrinolytic enzyme was purified, and the properties were studied. Results: A two-level full factorial design was used to screen the significant factors. The factors such as moisture, pH, and peptone were significantly affected enzyme production and these three factors were selected for further optimization using central composite design. The optimum medium for fibrinolytic enzyme production was wheat bran medium containing 1% peptone and 80% moisture with pH 8.32. Under these optimized conditions, the production of fibrinolytic enzyme was found to be 6851 U/g. The fibrinolytic enzyme was purified by 3.6-fold with 1275 U/mg specific activity. The molecular mass of fibrinolytic enzyme was determined by sodium dodecyl sulphate polyacrylamide gel electrophoresis, and it was observed as 29 kDa. The fibrinolytic enzyme depicted an optimal pH of 9.0 and was stable at a range of pH from 8.0 to 10.0. The optimal temperature was 60°C and was stable up to 50°C. This enzyme activated plasminogen and also degraded the fibrin net of blood clot, which suggested its potential as an effective thrombolytic agent. Conclusions: Wheat bran was found to be an effective substrate for the production of fibrinolytic enzyme. The purified fibrinolytic enzyme degraded fibrin clot. The fibrinolytic enzyme could be useful to make as an effective thrombolytic agent.

19th c. Coloured stuccos and plasters from Grilos' Church (Oporto, Portugal): Materials and techniques employed

The Oporto's St. Lourenço Church of the Jesuit College is locally known, since the St. Augustin Barefooted Eremites occupation (1779/80), as Grilos' Church. The Oporto's siege laid by D. Pedro and D. Miguel (1832/33) succeed in the college abandonment by Grilo's Friars. Throughout Augustin Friars presence period, the white plasters of the nave (end of 18th c.) were executed and it was constructed the Holly Sacrament Chapel (early 19th c.) with neoclassic coloured stuccos and plasters, influenced by Robert Adam, Luigi Chiari and Teixeira Barreto ornamental motifs. Pigments were added to the external layer to imitate the marble and to achieve the “base” colour of the panels. This study of the blue, rose and white stuccos and plasters of H.S. Chapel of Grilo's Church allows carrying out useful database on the original mortars composition by the use of different analytical techniques, important to select the most adequate solutions for restoration interventions. Optical microscopy, XRD, TG-DTA, SEM-EDS, XRF analysis results were considered to identify the composition of different layers and to provide mineralogical, microstructure and chemical characterization of the mortars components and to quantify the binder content in those mortars. These results were compared with collected information on compositions from other sources. This study allowed the identification of the decay causes of decorative stuccos and plaster, suggesting that water retention in the masonries and wooden laths structure of the dome of the chapel is the main factor.

Genome-wide analysis of G-type lectin genes in Fragaria vesca and functional characterization of FaMBL1 gene in defense response of F. × ananassa to fungal pathogens

Strawberry (Fragaria × ananassa) is an important soft fruit but easily to be infected by pathogens. Anthracnose and gray mold are two of the most destructive diseases of strawberry which lead to serious fruit rot. The first chapter introduced strawberry anthracnose caused by Colletotrichum acutatum. The infection strategy, disease cycle and management of C. acutatum on strawberry were reported. Likewise, the second chapter summarized the infection strategy of Botrytis cinerea and the defense responses of strawberry. As we already know white unripe strawberry fruits are more resistant to C. acutatum than red ripe fruits. During the interaction between strawberry white/red fruit and C. acutaum, a mannose binding lectin gene, FaMBL1, was found to be the most up-regulated gene and induced exclusively in white fruit. FaMBL1 belongs to the G-type lectin family which has important roles in plant development and defense process. To get insight into the role of FaMBL1, genome-wide identification was carried out on G-type lectin gene family in Fragaria vesca and the results were showed in chapter 3. G-type lectin genes make up a large family in F. vesca. Active expression upon biotic/abiotic stresses suggested a potential role of G-lectin genes in strawberry defenses. Hence, stable transgenic strawberry plants with FaMBL1 gene overexpressed were generated. Transformed strawberry plants were screened and identified. The results were showed in chapter 4, content of disease-related phytohormone, jasmonic acid, was found decreased in overexpressing lines compared with wild type (WT). Petioles inoculated by C. fioriniae of overexpressing lines had lower disease incidence than WT. Leaves of overexpressing lines challenged by B. cinerea showed remarkably smaller lesion diameters compared with WT. The chitinase 2-1 (FaChi2-1) showed higher expression in overexpressing lines than in WT during the interaction with B. cinerea, which could be related with the lower susceptibility of overexpressing lines.

Polyaniline-based materials and nanocomposites: from energy storage to sensing applications

The research work described in this thesis concerns materials for both energy storage and sensoristics applications. Firstly, the synthesis and characterization of magnetite (Fe3O4) functionalyzed with [3-(2-propynylcarbamate)propyl]triethoxysilane (PPTEOS) capable to reduce the gold precursor chloroauric acid (HAuCl4) without the need of additional reducing or stabilising agents is described. These nanoparticles were tested to improve performances of symmetric capacitors based on polyaniline and graphite foil. Energy storage applications were investigated also during six months stay at EPFL University of Lausanne where an investigation about different tailored catalysts for Oxygen Evolution Reaction in a particular Redox Flow Battery was carried out. For what concerns sensing applications, new materials based on cellulose modified with polyaniline and poly(2-acrylamido-2-methyl-1-propanesulfonic acid) (PAAMPSA) were synthesized, characterized and applied to monitor pressure, humidity, heart rate and lastly, bread fermentation in collaboration with the University of Fribourg and Zurich. The characterizations of all the materials investigated compriseed numerous techniques such as infrared attenuated total reflectance spectroscopy (IR-ATR), thermogravimetric analysis (TGA), scanning and transmission electron microscopy (SEM and TEM), alongside linear and cyclic voltammetry (LSV and CV), electrochemical impedance spectroscopy (EIS) and chronoamperometric analyses.