998 resultados para LigA
Resumo:
Pós-graduação em Biopatologia Bucal - ICT
Influência dos elementos de liga nos parâmetros de processo de fundição de ferros fundidos especiais
Resumo:
Pós-graduação em Engenharia Mecânica - FEG
Resumo:
Pós-graduação em Química - IQ
Resumo:
Modificações na composição química e no processamento termomecânico têm sido algumas das várias alternativas estudadas, para melhorar o desempenho de ligas de alumínio tradicionais. Neste trabalho foi modificada a composição de uma liga Al-Mn-Mg do tipo AA 3104, endurecível por deformação, adicionando-se diversos teores de zinco, transformando-a numa liga Al-Mn-Mg(Zn), endurecível por precipitação. O objetivo foi estudar e quantificar os efeitos do zinco sobre o processamento termomecânico e as propriedades mecânicas da liga modificada. Ligas com teores de zinco entre 0,03 a 1,52% foram fundidas e processadas obtendo-se um encruamento semelhante a condição H-19 industrial, denominada rota R. Ligas com teores de zinco entre 1,14 a 2,17% foram fundidas e processadas segundo três diferentes rotas: na rota S, o recozimento da rota R foi substituído por solubilização antes da laminação a frio; nas rotas E3H e E6H, as tiras laminadas a frio foram envelhecidas em dois estágios: 121°C por três horas para as duas rotas, mais três horas para a rota E3H e seis para a rota EH a 163°. A tensão de escoamento (SIGMA IND E) e a resistência à tração (SIGMA IND T) para a rota R aumentaram da ordem de 18% e 19% respectivamente, com o aumento do teor de zinco, enquanto o alongamento (E) permaneceu em torno de 4,5%. As propriedades mecânicas (SIGMA IND E SIGMA T E ) AUMENTARAM EM TORNO DE 25%, 31% E 27%, respectivamente, para a rota S. Considerando concentrações aproximadamente iguais de zinco, não foram verificadas diferenças significativas para (SIGMA E SIGMA T), entre as rotas R E S, no entanto, a rota S apresentou alongamento médio maior que a rota R da ordem 44%. Os menores valores de (SIGMA IND E SIGMA IND T) e os maiores valores de E foram obtidos para a rota E6H.
Resumo:
2,25Cr-1Mo alloy steels are widely used in petrochemical plant equipments working in high temperature conditions because of their good mechanical proprieties in these conditions. Although, when exposed for a long time at high temperature, in the rage of 343 °C to 593 °C, may present the temper embrittlement phenomenon. The component named stripper of assembly converter of fluid catalytic cracking unit (UFCC) of studied plant is manufactured using this material, which is subject to temper embrittlement. The phenomenon of temper embrittlement refers to progressive lose of toughness, making the material brittle. With embrittlement, equipaments manufactured with this material are under risks to suffer brittle fracture in the cool down and start-up situations of them, which can cause catastrophic failures. By this reason, this research studies presence of temper ebrittlement phenomenon on this material. To verify the toughness of the material is conventionally used charpy V-notch test. However, this test requires the removing of samples of the material to make specimens. This fact becomes critical when talk about structural components of an equipment. So, this research also studies a non-destructive test that can be executes in-situ, known as instrumented indentation, as an alternative detection of the phenomenon at the component stripper, by comparative of the mechanical proprieties obtained by conventional tests in similar samples
Resumo:
Aluminum alloys are widely used in industry, because they combine different mechanical properties according to the alloying elements used in addition to thermal and mechanical treatments performed, resulting in materials with good weight/resistance relation. The 7XXX series alloys are worked heat treatable alloys commonly used in the aerospace industry, especially due to their high mechanical properties obtained after aging heat treatment, which increases the interest around 7075 alloy. Some studies with alloys which can be aged show that it is possible that cold word processes affect the results of aging. Thus, this study was intended to verify the influence of the aging process of AA 7075 alloy. There were three routes of aging with specimens previously treated thermally. In the first route T6 treatment was performed with a annealed specimen and other in solid solution. The second was the natural aging in a annealed specimen. In the last route was done aging by steps with a annealed specimen and other in solid solution with the intention to reduce the effects of natural aging. The results show that the routes 1 and 3 had similar hardness for all the samples, showing that the validity of Route 3 as an alternative and also the hardening did not affect the hardness at the end of the process, significantly reducing the time required for the highest hardness. Finally, natural aging was less effective in increasing hardness
Resumo:
Alloy Al-7%Si-0,3Mg (AA356), having an excellent combination of properties such as low solidification shrinkage and good fluidity, good weldability, high wear resistance, high strength to weight particularly in the automotive and aerospace engineering. The refinement of the structure aluminum silicon eutectic alloy is a fairly common practice in the casting, through the treatment knows as modification. You can get the modification for the addition of chemicals and rare earths, these have the ability to modify the structure of the eutectic, but only sodium and strontium produce a strong action modifier when used in low concentrations. The modifying effect of silicon grain turns into a fibrous form branched and enveloped by the metal matrix in the form of a composite structure that has the highest limit of tensile strength, ductility and machinability. This work will be obtained AA356 alloy ingots using two different types of molds: metal mold and sand mold. Macrographs will be made in ingots obtained for observation of the macrostructures obtained in both types of ingots. Will be sampled at strategic locations of the ingots to correlate microstructure and cooling rate. The results showed that the material of the ingot has a strong influence on the resulting micro-andmacrostructure
Resumo:
The approach of the subject matter in this work relies on the fact that the reliability of methods for performance analysis of materials proves critical for the result. This work focused on the development and presentation of the methodology for lifting probability curves for fatigue test (SN) according to standard E739, this focus is justified by the fact that the results in fatigue test show considerable dispersion making it difficult to reading and interpretation of data, this dispersion arises because the phenomenon of rupture is strongly influenced by internal characteristics of the material, we can then have much data ranging from test to test. Thus we set out originally for a brief study of aluminum alloys in question, as well as the treatments to which they were subjected. We also studied the behavior of materials when subjected to cyclic loading, which configures process of fatigue failure, and even fatigue test method in question. This statistical analysis is based on the ASTM E739 standard, so its contents was studied in detail so that we could present in detail the methodology and raise SN curves for different aluminum alloy 7012 subjected to fatigue test. Data were collected from tests conducted in the department of materials from two samples of aluminum alloy 7012 solubilized and precipitated by different time intervals and assayed temperature fatigue-type traction-compression, these data were then analyzed and used to survey curves using the base as E739. After lifting the curve analyzed the characteristics of the test samples and their correlation with the test results. We confirmed the effectiveness of the method of statistical analysis by ASME E739, which allowed the reading of data without this method would be very difficult to have a reading and comparison of the results for the two types... (Complete abstract click electronic access below)
Resumo:
The increasing technological innovation and demand for materials with better properties boosts research into new materials and new alloys. To do so, aluminum alloys are being developed, among them the AA7075-T6, having many applications in aerospace and military industries, machinery and equipment, molds for plastic injection and structures. To study and understand the properties, characteristics and especially the microstructure of the material, the metallographic preparation is essential. This paper presents new methodologies to achieve the metallography of samples of scrap alloy AA7075-T6, with emphasis on methods of polishing. For the five samples, the best results were those with specific grinding, the samples only going down on the sander. For polishing, the most effective method so far has been using the polishing cloth 16.3, of ATM enterprise, solution of diamond 3 μm, solution of diamond 1 μm, and colloidal solution of OP-S. For the etching, the reactive agent used was phosphoric acid (H3PO4) 85% P.A., as 90% in the proportion of distilled water to 10% acid. The best results were obtained in the attacks of 300 and 240 seconds, revealing the grain boundaries in most areas. Methodologies need more studies and more tests, but the results have proved to be satisfactory
Resumo:
Titanium and its alloys have been used for biomedical applications due their excellent properties such as high corrosion resistance, biocompatibility and mechanical properites. In this study, microstructural and mechanical properties of Ti-30Ta alloy was evaluated during its processing. Ti-30Ta alloy ingots were produced from sheets of commercially pure titanium (99.9%) and tantalum (99.9%). Its melting was realized in arc melting furnace in an argon atmosphere. After homogenizing at 1200ºC, ingots were cold worked by swaging. Samples with 13 mm in diameter were obtained. They were forging at the reduction ratios of 15%. After deformation, microstructure was evaluated by optical microscopy in each condition. Also, Vickers microhardness of samples was measured and phase constitution was evaluated using XRD analysis
Resumo:
The macrostructure of an alloy solidification in the raw state is of utmost importance due to its influence on mechanical properties. A structure showing columnar grains is generally undesirable in most applications of cast products and grain refining aims to suppress the formation of these grains and get a fine-grained equiaxed structure that improves the supply of liquid metal and the mechanical properties, as yield strength and tensile strength limit, as well as the tendency of formation of hot cracks. The type and size of grains formed are determined by chemical composition, cooling rate and the use of inoculum for grain refining. Titanium and boron are the major refiners in the aluminum industry and can be added to the molten metal in the form of alloys such as Al-Ti, Al-Ti-B or Al-B. In this paper we will discuss the information obtained from cooling curves and first derivative of the cooling curve to obtain the thermal parameters that influence the process of grain refining alloy AA 356.0
Resumo:
The AA356 alloy is an alloy widely used in the automotive industry and aerospace due to its excellent mechanical properties. Refining the structure of eutectic silicon aluminum alloys is a fairly common practice in the foundry through treatment known as modification. This can be achieved by modifying agent adding chemicals such as contained in groups I and IIa of the periodic table and rare earths (europium, céreioi, praseodymium, neodymium, etc.). Has the ability to modify the structure of the eutectic, but only sodium and strontium produce an action modifier strong when used in low concentrations. The modifying effect of the shafts turn silicon into a fibrous form and branched surrounded by metallic matrix in the form of a composite structure that has the highest limit of tensile strength, ductility and machinability. In this work will be obtained ingots with and without the modifier type Al-10% Sr, made in sand molds and are generated and analyzed cooling curves and also the study of the macrostructure and microstructure of the solidified material. It was found that by adding the Al-Sr made shorten the solidification time and lower the grain size
Resumo:
In this work, the influence of modifications of the cp-Ti and Ti 6Al 4V alloy, by treating the surface with NaOH and depositing titanium oxide and hydroxyapatite by sol-gel method, on their biocompatibility was studied. The coatings were characterized by scanning electron microscopy and X-ray diffraction which showed that the coatings on Ti 6Al 4V are better than on cp-Ti. Adhesion tests showed that adhesion strength of the coatings on cp-Ti substrate is less than on Ti 6Al 4V as well as cytotoxicity for L929 fibroblast cells is higher
Resumo:
This study aimed to analyze the cooling curves, micro and macrograph alloy Al-1 %Si without the addition of strontium modifier and with the addition of the same. One of the ways of improving mechanical properties of alloy Al -Si is through the modification process. For the experiments two billets of the alloy Al-1%Si cast iron mold in a billet with addition of 0.02% strontium by weight, and the other billet without the addition of modifier were fused. In the solidification process of billet temperature was monitored and recorded every second for later plotting in Origin 8 program and analyzes the cooling curves obtained. The billets were cut and passed by grinding and polishing to perform the macrograph and micrographs. The results concerning the macrograph indicated that billet without the addition of Strontium particle size obtained was more refined than the billet where the strontium modifier was added. Regarding the micrograph, photos stemmed from the optical microscope didn´t show the expected modification effect by the addition of Strontium. This suggests that the low amount of silicon (1 %) present in the alloy used in this study interfered in the change process, because according to the literature review, Strontium 0.022 % by weight is sufficient to fully modify an alloy with 7% Silicon. The results from the cooling curve showed that both the eutectic temperature and the solidification time remained unchanged with the addition of strontium
Resumo:
One of the ways to minimize the effects of unproductive time caused by tool wear can be achieved by introducing an efficient system of lubrication and cooling in the process. However, in the last decade the research had the goal to restrict the maximum use of refrigerants and / or lubricants in metal-mechanical production. The important factors that justify this procedure include the operational costs of production, ecological issues, and the legal requirements of environmental conservation and preservation of human health. The purpose of the proposed work is the study of machining by turning with the focus on the influence caused by the application of cutting fluid in several ways of application (abundant and MQF) and also by comparing the results obtained by machining without the presence of fluid . For this purpose, the turning tests are conducted using an aluminum alloy (AA 7075). The response variables to be analyzed were obtained from the roughness (Ra and Ry), the stresses presented (VB) and their progression in relation to the cutting length achieved, the type of chip formed, in addition to changes in the degree of finish (roughness) presented by the turned parts. The results of this study should provide more detailed information about the actual influence of cutting fluids in turning this alloy, which are characterized by high rates of deformation when the formation of damaging your chip machining and also the quality of surface generated. Therefore, it is expected to provide subsidies to promote the optimization of machining this alloy making the most of the role of cutting fluid