Bismuth germanate films prepared by Pechini method

Bismuth germanate films were prepared by dip coating and spin coating techniques and the dependence of the luminescent properties of the samples on the resin viscosity and deposition technique was investigated. The resin used for the preparation of the films was obtained via Pechini method, employing the precursors Bi(2)O(3) and GeO(2). Citric acid and ethylene glycol were used as chelating and cross-linking agents, respectively. Results from X-ray diffraction and Raman spectroscopy indicated that the films sintered at 700 degrees C for 10 h presented the single crystalline phase Bi(4)Ge(3)O(12). SEM images of the films have shown that homogeneous flat films can be produced by the two techniques investigated. All the samples presented the typical Bi(4)Ge(3)O(12) emission band centred at 505 nm. Films with 3.1 mu m average thickness presented 80% of the luminescence intensity registered for the single crystal at the maximum wavelength. Published by Elsevier B.V.

Two- and three-dimensional shape fabric analysis by the intercept method in grey levels

The count intercept is a robust method for the numerical analysis of fabrics Launeau and Robin (1996). It counts the number of intersections between a set of parallel scan lines and a mineral phase, which must be identified on a digital image. However, the method is only sensitive to boundaries and therefore supposes the user has some knowledge about their significance. The aim of this paper is to show that a proper grey level detection of boundaries along scan lines is sufficient to calculate the two-dimensional anisotropy of grain or crystal distributions without any particular image processing. Populations of grains and crystals usually display elliptical anisotropies in rocks. When confirmed by the intercept analysis, a combination of a minimum of 3 mean length intercept roses, taken on 3 more or less perpendicular sections, allows the calculation of 3-dimensional ellipsoids and the determination of their standard deviation with direction and intensity in 3 dimensions as well. The feasibility of this quick method is attested by numerous examples on theoretical objects deformed by active and passive deformation, on BSE images of synthetic magma flow, on drawing or direct analysis of thin section pictures of sandstones and on digital images of granites directly taken and measured in the field. (C) 2010 Elsevier B.V. All rights reserved.

Surface bands on deepwater squalid dorsal-fin spines : an alternative method for ageing centroselachus crepidater

Bands on the external surface of the second dorsal-fin spine proved to be a novel method of estimating the age and growth of Centroselachus crepidater. Bands that followed the shape of the spine base were enhanced with an alizarin red derivative. Internal bands in spine cross sections were also examined. The number of both external and internal bands increased with animal size, although most spines had more external than internal bands. External bands were more reliable and were assumed to be annuli. The rate of band formation differed after five bands had been formed, and internal bands ceased forming after 30 years. Females to 54 years old and males to 34 years old were examined. Maturity occurred over a wide age range, with estimates of 20 years for females and 9 years for males. The youngest pregnant female was 27 years old. The Francis reparameterized von Bertalanffy growth model found similar growth for males and females, and the von Bertalanffy equations were L _t = 96.12^{(1 – e(–0.072(t+6.13))}) for females and L_t = 73.22(1 – e^{(–0.141(t+2.99))}) for males.

An improved method for the purification of rat liver-type fatty acid binding protein from Escherichia coli

We have developed expedient and reliable methods to isolate cyclosporin synthetase for in vitro biosynthesis of cyclosporins. We have examined enzyme purification strategies suited to large-scale processing and present a chromatographic sequence that serves as a pilot model for industrial scale preparation of cyclosporin synthetase from cyclosporin producing fungi. A chromatographic sequence consisting of ammonium sulfate precipitation → gel filtration → hydrophobic interaction chromatography → anion exchange chromatography, yielded an electrophoretically homogeneous cyclosporin synthetase preparation (Coomassie G-250 brilliant blue staining). Furthermore, a native polyacrylamide gel electrophoresis system was developed for the isolation of active cyclosporin synthetase enzyme from crude extracts of cyclosporin producing fungi. The environmental factors affecting enzyme stability and the continuity of the in vitro cyclosporin biosynthetic reaction-temperature, pH, and substrate depletion were assessed and manageable conditions have been defined for sustainable cyclosporin biosynthesis with enzyme isolates. Cyclosporin synthetase exhibited an optimal temperature range of 24–29 °C and a pH optimum of 7.6. The native enzyme displayed a pI of 5.7, as determined by isoelectric focusing. The industrial implementation of an in vitro biosynthetic approach could potentially prove useful for the production of important therapeutic cyclosporins which occur as only minor fermentation by-products.

The reliability of muscle biopsies taken from vastus lateralis

The purpose of this study was to examine whether a single biopsy sample of vastus lateralis could provide an accurate estimate of capillary density (CD) which is indicative of the entire muscle, or whether capillary density is distributed unevenly and varies with muscle depth. Whole muscle cross sections of vastus lateralis were excised post mortem (n=11) for analysis of capillary density at three muscle depths, (superficial, mid and deep regions). Muscle thickness varied widely (17–79mm) across subjects. The distribution of CD throughout the depth of the muscle was homogeneous in 8 subjects, but in 3 subjects it was heterogeneous (p<0.05). In 3 of these subjects there was a significant (p<0.05) effect of sample depth on CD. These data indicate that tissue from a single biopsy will not adequately represent the CD of the entire vastus lateralis in some individuals. Single biopsies from unspecified muscle depth, have routinely been used to estimate CD and fibre type in vastus lateralis. The present study indicates that a more reliable method of analysis would be to use the tissue from two needle biopsies taken at the superficial and deep portions of the muscle from a group of at least 10 subjects. Sampling theory analysis supported this conclusion.

A design-based method for estimating glomerular number in the developing kidney

Low glomerular (nephron) endowment has been associated with an increased risk of cardiovascular and renal disease in adulthood. Nephron endowment in humans is determined by 36 wk of gestation, while in rats and mice nephrogenesis ends several days after birth. Specific genes and environmental perturbations have been shown to regulate nephron endowment. Until now, design-based method for estimating nephron number in developing kidneys was unavailable. This was due in part to the difficulty associated with unambiguously identifying developing glomeruli in histological sections. Here, we describe a method that uses lectin histochemistry to identify developing glomeruli and the physical disector/fractionator principle to provide unbiased estimates of total glomerular number (Nglom). We have characterized Nglom throughout development in kidneys from 76 rats and model this development with a 5-parameter logistic equation to predict Nglom from embryonic day 17.25 to adulthood (r2 = 0.98). This approach represents the first design-based method with which to estimate Nglom in the developing kidney.

An analytical approach to predict web-warping and longitudinal strain in flexible roll formed sections of variable width

To reduce weight and improve passenger safety there is an increased need in the automotive industry to use Ultra High Strength Steel (UHSS) for structural and crash components. However, the application of UHSS is restricted by their limited formability and the difficulty of forming them in conventional stamping. An alternative method of manufacturing structural auto body parts from UHSS is the flexible roll forming process, which allows the manufacture of metal sheet with high strength and limited ductility into complex and weight-optimized components. One major problem in the flexible roll forming of UHSS is the web-warping defect, which is the deviation in height of the web area over the length of the profile. It has been shown that web-warping is strongly dependant to the permanent longitudinal strain formed in the flange of the part. Flexible roll forming is a continuous process with many roll stands, which makes numerical analysis extremely time intensive and computationally expensive. An analytical model of web-warping is therefore critical to improve design efficiency during the early process design stage before FEA is applied. This paper establishes for the first time an analytical model for the prediction of web-warping for the flexible roll forming of a section with variable width. The model is based on evaluating longitudinal edge strain in the flange of the part. This information is then used in combination with a simple geometrical model to investigate the relationship between web-warping and longitudinal strain with respect to process parameters.

Effects of Etching on Zircon Grains and Its Implications for the Fission Track Method

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

A Model for Bundled Conductors considering a Non-Homogeneous Distribution of the Current through Subconductors

This paper describes an alternative procedure to obtain an equivalent conductor from a bundled conductor, taking into account the distribution of the current in subcondutors of the bundle. Firstly, it is introduced a brief background about the concept of Geometric Mean Radius (GMR) and how this methodology is applied to define an equivalent conductor and its electric parameters. Emphasizing that the classical procedure, using GMR, is limited to premise which the current is equally distributed through subconductors. Afterwards, it is described the development of proposed method and applications for an equivalent conductor obtained from a conventional transmission line bundled conductor and from an equivalent conductor based on a bundle with compressed SF(6) insulation system, where the current is unequally distributed through subconductors.

Staining methods applied to glycol methacrylate embedded tissue sections

The use of glycol methacrylate (GMA) avoids some technical artifacts, which are usually observed in paraffin-embedded sections, providing good morphological resolution. on the other hand, weak staining have been mentioned during the use of different methods in plastic sections. In the present study, changes in the histological staining procedures have been assayed during the use of staining and histochemical methods in different GMA-embedded tissues.Samples of tongue, submandibular and sublingual glands, cartilage, portions of respiratory tract and nervous ganglion were fixed in 4% formaldehyde and embedded in glycol methacrylate. The sections of tongue and nervous ganglion were stained by H&E. Picrosirius, Toluidine Blue and Sudan Black B methods were applied, respectively, for identification of collagen fibers in submandibular gland, sulfated glycosaminoglycans in cartilage (metachromasia) and myelin lipids in nervous ganglion. Periodic Acid-Schiff (PAS) method was used for detection of glycoconjugates in submandibular gland and cartilage while AB/PAS combined methods were applied for detection of mucins in the respiratory tract. In addition, a combination of Alcian Blue (AB) and Picrosirius methods was also assayed in the sublingual gland sections.The GMA-embedded tissue sections showed an optimal morphological integrity and were favorable to the staining methods employed in the present study. In the sections of tongue and nervous ganglion, a good contrast of basophilic and acidophilic structures was obtained by H&E. An intense eosinophilia was observed either in the striated muscle fibers or in the myelin sheaths in which the lipids were preserved and revealed by Sudan Black B. In the cartilage matrix, a strong metachromasia was revealed by Toluidine Blue in the negatively-charged glycosaminoglycans. In the chondrocytes, glycogen granules were intensely positive to PAS method. Extracellular glycoproteins were also PAS positive in the basal membrane and in the region occupied by the lamina externa and reticular fibers surrounding each smooth muscle cells of the blood vessels. In the epithelial cells of the respiratory tract, acid and neutral mucins were histochemically detected by AB and PAS methods, respectively. Moreover, granules containing acid and neutral mucins were revealed in purple by AB and PAS concomitantly. In the sublingual gland sections, a distinct affinity of acid mucins by AB (in turquoise-blue) and collagen fibers by Picrosirius (in red) was obtained when these methods were combined. Although some routine dyes used in paraffin sections have showed a weak stain in historesin sections, our results showed that different dyes could be applied in GMA sections if modified staining procedures were assayed. Therefore, appropriate staining contrast and, thus, detection of one or different substances in a same section can be acquired in association to the good morphological resolution provided by GMA. (C) 2003 Elsevier Ltd. All rights reserved.

Topological signatures in CMB temperature anisotropy maps

We propose an alternative formalism to simulate cosmic microwave background (CMB) temperature maps in Lambda CDM universes with nontrivial spatial topologies. This formalism avoids the need to explicitly compute the eigenmodes of the Laplacian operator in the spatial sections. Instead, the covariance matrix of the coefficients of the spherical harmonic decomposition of the temperature anisotropies is expressed in terms of the elements of the covering group of the space. We obtain a decomposition of the correlation matrix that isolates the topological contribution to the CMB temperature anisotropies out of the simply connected contribution. A further decomposition of the topological signature of the correlation matrix for an arbitrary topology allows us to compute it in terms of correlation matrices corresponding to simpler topologies, for which closed quadrature formulas might be derived. We also use this decomposition to show that CMB temperature maps of (not too large) multiply connected universes must show patterns of alignment, and propose a method to look for these patterns, thus opening the door to the development of new methods for detecting the topology of our Universe even when the injectivity radius of space is slightly larger than the radius of the last scattering surface. We illustrate all these features with the simplest examples, those of flat homogeneous manifolds, i.e., tori, with special attention given to the cylinder, i.e., T-1 topology.

Epitaxially grown LiNbO3 thin films by polymeric precursor method

LiNbO3 thin films were grown on (0001) sapphire substrates by a chemical route, using the polymeric precursor method. The overall process consists of preparing a coating solution from the Pechini process, based on metallic citrate polymerization, the precursor films, deposited by dip coating, are then heat treated to eliminate the organic material and to synthesize the phase. In this work, we studied the influence of the heat treatment on the structural and optical properties of single-layered films. Two routes were also investigated to increase the film thickness: increasing the viscosity of the coating solution and/or increasing the number of successively deposited layers. The x-ray diffraction theta -2 theta scans revealed the c-axis orientation of the single- and multilayered films and showed that efficient crystallization can be obtained at temperatures as low as 400 degreesC, the phi-scan diffraction evidenced the epitaxial growth with two in-plane variants, A microstructural study revealed that the films were crack free, homogeneous, and relatively dense. Finally, the investigation of the optical properties (optical transmittance and refractive index) confirmed the good quality of the films. These results indicate that the polymeric precursor method is a promising process to develop lithium niobate waveguides.

Optical properties of potassium niobate thin films prepared by the polymeric precursor method

Thin films of potassium niobate were deposited on MgO (100) substrates by the polymeric precursor method and annealing in static air at 600 degreesC for 20 h. The obtained films were characterized by X-ray diffraction, atomic force microscopy (AFM) and the prism coupling method. The phi-scan diffraction evidenced the growth of the films with fourfold symmetry. AFM study shows that the films are homogeneous, dense and present a smooth surface. The refractive index and optical losses were strongly influenced by the degree of crystallinity. (C) 2004 Elsevier B.V. All rights reserved.

Picrosirius-polarization staining method as an efficient histopathological tool for collagenolysis detectin in vesical prolapse lesions

The Picrosirius-polarization method has been indicated as a selective histochemical stain for collagen detection in tissue sections. This method can also be of value for studying collagen degradation given that, under polarized light, collagen displays birefringence due to its molecular order. The aim of this study is to highlight this staining method as an additional instrument for a rapid and excellent confirmatory diagnosis of the presence of collagenolysis in connective tissue in the vaginal wall with vesical prolapse lesion, in tissue sections. Dramatic changes in collagen morphology were found in vaginal mucosa in vesical prolapse disorder: they were weakly stained by Sirius red and under polarized light appeared as thin, pale (weakly birefringent), greenish, and with fibers more scattered, while the histoarchitecture of the organ showed a disrupted appearance. Thus, in the present study, we showed in vaginal mucosa in the vesicle prolapse that corroded collagenous framework appears as fragmentary and irregularly separated collagenous structures, that are weakly birefringent, corresponding to a molecular disorganization of these fibers caused by collagenolysis. (C) 2006 Elsevier Ltd. All rights reserved.

Manganese(III) porphyrins: Catalytic activity and intermediate studies in homogeneous systems

We studied how solvent, stirring method, PhIO/MnP molar ratio, presence of water and axial ligand affect the catalytic activities of Mn(TPP)Cl, Mn(MNPP)Cl, Mn(TDCPP)Cl and Mn(TFPP)Cl in the oxidation of cyclohexane by PhIO. A study of the catalytic intermediates in the reaction between Mn(TPP)Cl or Mn(TDCPP)Cl and PhIO was also carried out by UV-Vis and EPR spectroscopies. The reaction of Mn(TPP)Cl with PhIO showed the formation of a mixture of species Mn-IV(OP+ and Mn-V(O)P as intermediates, which were confirmed by the deconvolution of the UV-Vis spectra. Addition of imidazole as cocatalyst favoured the formation of the intermediate species Mn-V(O)P, evidenced by the UV-Vis band at 408 nm. The corresponding EPR spectra gave evidence that in the presence of imidazole, Mn-IV(OP+ species are formed only in very low amounts. For Mn(TDCPP)Cl the dominating intermediate species is Mn-IV(OP+. Addition of imidazole to halogen-substituted MnP systems does not result in increase of the C-ol yields because very stable bis-imidazole-MnP complexes are formed. Anchoring of such MnP on imidazole propyl gel (IPG) results in better catalytic activity because in this case, the catalyst is mono-coordinated to the support and imidazole favours the formation of the intermediate species Mn-V(O)P.