Assessing the behaviour of RC beams subject to significant gravity loads under cyclic loads

Gravity loads can affect a reinforced concrete structure's response to seismic actions, however, traditional procedures for testing the beam behaviour do not take this effect into consideration. An experimental campaign was carried out in order to assess the influence of the gravity load on RC beam connection to the column subjected to cyclic loading. The experiments included the imposition of a conventional quasi-static test protocol based on the imposition of a reverse cyclic displacement history and of an alternative cyclic test procedure starting from the gravity load effects. The test results are presented, compared and analysed in this paper. The imposition of a cyclic test procedure that included the gravity loads effects on the RC beam ends reproduces the demands on the beams' critical zones more realistically than the traditional procedure. The consideration of the vertical load effects in the test procedure led to an accumulation of negative (hogging) deformation. This phenomenon is sustained with the behaviour of a portal frame system under cyclic loads subject to a significant level of the vertical load, leading to the formation of unidirectional plastic hinges. In addition, the hysteretic behaviour of the RC beam ends tested was simulated numerically using the nonlinear structural analysis software - OpenSees. The beam-column model simulates the global element behaviour very well, as there is a reasonable approximation to the hysteretic loops obtained experimentally. (C) 2013 Elsevier Ltd. All rights reserved.

Experimental and numerical evaluation of composite repairs on wood beams damaged by cross-graining

An experimental and Finite Element study was performed on the bending behaviour of wood beams of the Pinus Pinaster species repaired with adhesively-bonded carbon–epoxy patches, after sustaining damage by cross-grain failure. This damage is characterized by crack growth at a small angle to the beams longitudinal axis, due to misalignment between the wood fibres and the beam axis. Cross-grain failure can occur in large-scale in a wood member when trees that have grown spirally or with a pronounced taper are cut for lumber. Three patch lengths were tested. The simulations include the possibility of cohesive fracture of the adhesive layer, failure within the wood beam in two propagation planes and patch interlaminar failure, by the use of cohesive zone modelling. The respective cohesive properties were estimated either by an inverse method or from the literature. The comparison with the tests allowed the validation of the proposed methodology, opening a good perspective for the reduction of costs in the design stages of these repairs due to extensive experimentation.

Low-power 6-bit 1-GS/s two-channel pipeline ADC with open-loop amplification using amplifiers with local-feedback

IEEE International Symposium on Circuits and Systems, pp. 2258 – 2261, Seattle, EUA

A hybrid procedure to identify the optimal stiffness coefficients of elastically restrained beams

The formulation of a bending vibration problem of an elastically restrained Bernoulli-Euler beam carrying a finite number of concentrated elements along its length is presented. In this study, the authors exploit the application of the differential evolution optimization technique to identify the torsional stiffness properties of the elastic supports of a Bernoulli-Euler beam. This hybrid strategy allows the determination of the natural frequencies and mode shapes of continuous beams, taking into account the effect of attached concentrated masses and rotational inertias, followed by a reconciliation step between the theoretical model results and the experimental ones. The proposed optimal identification of the elastic support parameters is computationally demanding if the exact eigenproblem solving is considered. Hence, the use of a Gaussian process regression as a meta-model is addressed. An experimental application is used in order to assess the accuracy of the estimated parameters throughout the comparison of the experimentally obtained natural frequency, from impact tests, and the correspondent computed eigenfrequency.

Simulation of the velocity field in compound channel flow using different closure models

1st European IAHR Congress,6-4 May, Edinburg, Scotland

Ultrasound velocity profile (UVP) measurements in shallow open-channel flows

1st European IAHR Congress, 6-4 May, Edinburgh, Scotland

Flow resistance in open-channel flows with mobile hydraulically rough beds

River Flow 2008, Vol.1

Propagation of waves generated by a pressure disturbance moving in a channel

This paper studies the effect of ship speed and water depth on the propagation of ship generated waves. The ship is represented by a moving pressure distribution function at the free surface that is able to reproduce most of the phenomena involved in wave propagation. Results are obtained for a ship sailing along a coastal stretch made of a sloping bottom and a constant depth region. The results show that in the sloping bottom the crests of waves are bent along the slope and in the constant depth the standard Kelvin wave patterns can be found for the subcritical regime. In the critical regime the wave system is characterized by significant diverging waves and for a supercritical regime, the transverse waves disappear. © 2015 Taylor & Francis Group, London.

Experimental Reinforcement of Wood Beams

Rehabilitation is becoming more and more usual in the construction sector in Portugal. The introduction of newer construction materials and technical know-how of integrating different materials for achieving desired engineering goals is an important step to the development of the sector. Wood industry is also getting more and more adapted to composite technologies with the introduction of the so called “highly engineered wood products” and with the use of modification treatments. This work is an attempt to explain the viability of using stainless steel and glass fibre reinforced polymer (GFRP) as reinforcements in wood beams. This thesis specifically focuses on the flexural behaviour of Portuguese Pine unmodified and modified wood beams. Two types of modification were used: 1,3-dimethylol-4,5- dihydroxyethyleneurea (DMDHEU) resin and amid wax. The behaviour of the material was analysed with a nonlinear model. The latter model simulates the behaviour of the reinforced wood beams under flexural loading. Small-scale beams (1:15) were experimented in flexural bending and the experimental results obtained were compared with the analytical model results. The experiments confirm the viability of the reinforcing schemes and the working procedures. Experimental results showed fair agreement with the nonlinear model. A strength increase between 15% and 80% was achieved. Stiffness increased by 40% to 50% in beams reinforced with steel but no significant increase was achieved with the glass fibre reinforcement.

Transverse Vibrations in Beams Supported by a Piece-Wise Homogeneous Visco- Elastic Foundation

Transversal vibrations induced by a load moving uniformly along an infinite beam resting on a piece-wise homogeneous visco-elastic foundation are studied. Special attention is paid to the additional vibrations, conventionally referred to as transition radiations, which arise as the point load traverses the place of foundation discontinuity. The governing equations of the problem are solved by the normalmode analysis. The solution is expressed in a form of infinite sum of orthogonal natural modes multiplied by the generalized coordinate of displacement. The natural frequencies are obtained numerically exploiting the concept of the global dynamic stiffness matrix. This ensures that the frequencies obtained are exact. The methodology has restrictions neither on velocity nor on damping. The approach looks simple, though, the numerical expression of the results is not straightforward. A general procedure for numerical implementation is presented and verified. To illustrate the utility of the methodology parametric optimization is presented and influence of the load mass is studied. The results obtained have direct application in analysis of railway track vibrations induced by high-speed trains when passing regions with significantly different foundation stiffness.

As crianças e a internet. Crianças e tweens, as redes sociais e as ferramentas interactivas em Portugal - uma análise do canal temático ‘DISNEY CHANNEL PORTUGAL’

Trabalho projecto de mestrado em Novos Media e Práticas Web

Dimensionamento de Uma Cobertura em Elementos Estruturais de Aço Enformados a Frio

O presente relatório versa sobre a análise e dimensionamento de estruturas de aço enformadas a frio. Devido a serem estruturas de elevada esbelteza, frequentemente denominadas “estruturas de aço leve”, apresentam fenómenos de instabilidade tanto a nível local como global, sendo da perspetiva regulamentar abrangidas pelo Eurocódigo 3, nomeadamente pelas Partes 1-1, 1-3 e 1-5. A Parte 1-3 do Eurocódigo 3 diz respeito às regras suplementares de elementos de aço enformados a frio, na qual estão presentes as regras de dimensionamento, bem como as verificações de segurança que deverão ser aplicadas. Nesta, é possível ainda “fazer a ponte” com a Parte 1-1 do Eurocódigo 3, respetiva às regras gerais de projeto de estruturas de aço e com a Parte 1-5 do Eurocódigo 3 relativa a elementos estruturais constituídos por placas. Inicialmente, será realizado um estado da arte, onde será efetuado um enquadramento histórico, apresentando o processo de fabrico destes elementos e o tipo de elementos estruturais originados, concluindo-se com as vantagens/desvantagens dos perfis em aço enformados a frio. Os conceitos teóricos de estabilidade estrutural, os tipos de instabilidade mais comuns nestes elementos, bem como os tipos de análise destes fenómenos farão a ponte com o capítulo que se segue. Relativamente ao dimensionamento destes elementos, será dado enfâse às metodologias preconizadas pelo Eurocódigo 3, Parte 1-3. Este capítulo incidirá, entre outos, nas propriedades das secções transversais, na determinação da resistência destas, onde se contabilizará os efeitos das instabilidades locais de placa e distorcionais, na instabilidade global dos perfis e nas ligações entre os mesmos. Será analisada, posteriormente, a abordagem apresentada pela ECCS relativamente ao dimensionamento de madres travadas por painéis de cobertura. Neste capítulo será apresentada a metodologia para o dimensionamento de vigas com restrição à torção e à translação, bem como a resistência da secção transversal da madre e do seu banzo livre à encurvadura. Finalmente, e ao encontro do que foi proposto pela empresa CCAD-Serviços de Engenharia, Lda, efetuar-se-á o dimensionamento de uma cobertura de um edifício de distribuição, cobertura esta constituída por asnas treliçadas e madres simples. Neste dimensionamento foram consideradas as ações segundo o Regulamento de Segurança e Ações Para Estruturas de Edifícios e Pontes e o Eurocódigo 1, Parte 1-1 que diz respeito às Ações Gerais em Estruturas e Parte 1-4 respeitante às Ações do vento.

Dimensionamento de lajes aligeiradas betonadas "in situ"

A conjuntura económica da construção não se encontra numa fase de prosperidade, existindo a necessidade de criar soluções construtivas que permitam a redução de custos dos materiais a nível de obra. As lajes de betão armado, devido à sua grande área de implantação, possuem uma parcela importante no orçamento final de qualquer obra de edifícios correntes. Sabendo das possibilidades de aligeiramento de lajes, torna-se necessária a realização de um estudo pormenorizado e comparativo entre soluções de aligeiramento. O desenvolvimento deste relatório reflete todo o trabalho efetuado durante a realização de um estágio curricular desenvolvido na empresa FercaNorte – Estruturas, Lajes e Cofragens, Lda. e foca-se num dimensionamento e estudo comparativo de soluções de lajes fungiformes aligeiradas, aplicadas a dois casos de estudo e também num dimensionamento e estudo comparativo de soluções de lajes aligeiradas unidirecionais mas apenas aplicadas a um caso de estudo. No primeiro caso de estudo, laje fungiforme com um vão de 6 metros nas duas direções, são dimensionadas e comparadas quatro soluções: laje fungiforme maciça; laje fungiforme aligeirada com blocos elipsoides perdidos dispostos de forma ortogonal e envolvidos totalmente por betão; laje fungiforme aligeirada com blocos elipsoides perdidos dispostos em formato de favo de mel e envolvidos totalmente por betão; e laje fungiforme nervurada com moldes recuperáveis. No segundo caso de estudo, laje fungiforme com um vão de 7,04 metros nas duas direções, são dimensionadas e comparadas cinco soluções: laje fungiforme maciça, laje fungiforme aligeirada com blocos cúbicos perdidos dispostos de forma ortogonal e envolvidos totalmente por betão; laje fungiforme aligeirada, com blocos elipsoides perdidos dispostos de forma ortogonal e envolvidos totalmente por betão; laje fungiforme aligeirada com blocos elipsoides perdidos dispostos em formato de favo de mel e envolvidos totalmente por betão; e laje fungiforme nervurada com moldes recuperáveis. No terceiro caso de estudo, laje unidirecional com um vão de 8 metros apoiada em vigas com vão de 5 metros, são dimensionadas e comparadas três soluções: laje maciça; laje aligeirada com perfis tubulares com secção transversal reta oval; e laje nervurada com moldes recuperáveis. No final é apresentada uma estimativa orçamental para cada solução analisada nos três casos de estudo abordados.

Coherent structures in open channel flows with bed load transport over an hydraulically rough bed

Dissertação para obtenção do Grau de Mestre em Engenharia Civil – Perfil de Estruturas

Energy-efficient diversity combining for different access schemes in a multi-path dispersive channel

Dissertação para obtenção do Grau de Doutor em Engenharia Electrotécnica e Computadores