Development of site-specific sediment quality guidelines for North and South Atlantic littoral zones: Comparison against national and international sediment quality benchmarks

We aimed to develop site-specific sediment quality guidelines (SQGs) for two estuarine and port zones in Southeastern Brazil (Santos Estuarine System and Paranagua Estuarine System) and three in Southern Spain (Ria of Huelva, Bay of Cadiz, and Bay of Algeciras), and compare these values against national and traditionally used international benchmark values. Site-specific SQGs were derived based on sediment physical-chemical, toxicological, and benthic community data integrated through multivariate analysis. This technique allowed the identification of chemicals of concern and the establishment of effects range correlatively to individual concentrations of contaminants for each site of study. The results revealed that sediments from Santos channel, as well as inner portions of the SES, are considered highly polluted (exceeding SQGs-high) by metals, PAHs and PCBs. High pollution by PAHs and some metals was found in Sao Vicente channel. In PES, sediments from inner portions (proximities of the Ponta do Mix port`s terminal and the Port of Paranagua) are highly polluted by metals and PAHs, including one zone inside the limits of an environmental protection area. In Gulf of Cadiz, SQGs exceedences were found in Ria of Huelva (all analysed metals and PAHs), in the surroundings of the Port of CAdiz (Bay of CAdiz) (metals), and in Bay of Algeciras (Ni and PAHs). The site-specific SQGs derived in this study are more restricted than national SQGs applied in Brazil and Spain, as well as international guidelines. This finding confirms the importance of the development of site-specific SQGs to support the characterisation of sediments and dredged material. The use of the same methodology to derive SQGs in Brazilian and Spanish port zones confirmed the applicability of this technique with an international scope and provided a harmonised methodology for site-specific SQGs derivation. (C) 2009 Elsevier B.V. All rights reserved.

An overview of biodiesel soil pollution: Data based on cytotoxicity and genotoxicity assessments

Biodiesel production has received considerable attention in the recent past as a nonpolluting fuel. However, this assertion has been based on its biodegradability and reduction in exhaust emissions. Assessments of water and soil biodiesel pollution are still limited. Spill simulation with biodiesel and their diesel blends in soils were carried out, aiming at analyzing their cytotoxic and genotoxic potentials. While the cytotoxicity observed may be related to diesel contaminants, the genotoxic and mutagenic effects can be ascribed to biodiesel pollutants. Thus, taking into account that our data stressed harmful effects on organisms exposed to biodiesel-polluted soils, the designation of this biofuel as an environmental-friendly fuel should be carefully reviewed to assure environmental quality. (C) 2011 Elsevier B.V. All rights reserved.

Metal biosorption onto dry biomass of Arthrospira (Spirulina) platensis and Chlorella vulgaris: Multi-metal systems

Binary and ternary systems of Ni2+, Zn2+, and Pb2+ were investigated at initial metal concentrations of 0.5, 1.0 and 2.0 mM as competitive adsorbates using Arthrospira platensis and Chlorella vulgaris as biosorbents. The experimental results were evaluated in terms of equilibrium sorption capacity and metal removal efficiency and fitted to the multi-component Langmuir and Freundlich isotherms. The pseudo second order model of Ho and McKay described well the adsorption kinetics, and the FT-IR spectroscopy confirmed metal binding to both biomasses. Ni2+ and Zn2+ interference on Pb2+ sorption was lower than the contrary, likely due to biosorbent preference to Pb. In general, the higher the total initial metal concentration, the lower the adsorption capacity. The results of this study demonstrated that dry biomass of C. vulgaris behaved as better biosorbent than A. platensis and suggest its use as an effective alternative sorbent for metal removal from wastewater. (C) 2012 Elsevier B.V. All rights reserved.

Integration of processes induced air flotation and photo-Fenton for treatment of residual waters contaminated with xylene

Produced water in oil fields is one of the main sources of wastewater generated in the industry. It contains several organic compounds, such as benzene, toluene, ethyl benzene and xylene (BTEX), whose disposal is regulated by law. The aim of this study is to investigate a treatment of produced water integrating two processes, i.e., induced air flotation (IAF) and photo-Fenton. The experiments were conducted in a column flotation and annular lamp reactor for flotation and photodegradation steps, respectively. The first order kinetic constant of IAF for the wastewater studied was determined to be 0.1765 min(-1) for the surfactant EO 7. Degradation efficiencies of organic loading were assessed using factorial planning. Statistical data analysis shows that H2O2 concentration is a determining factor in process efficiency. Degradations above 90% were reached in all cases after 90 min of reaction, attaining 100% mineralization in the optimized concentrations of Fenton reagents. Process integration was adequate with 100% organic load removal in 20 min. The results of the integration of the IAF with the photo-Fenton allowed to meet the effluent limits established by Brazilian legislation for disposal. (C) 2011 Elsevier B.V. All rights reserved.

L'analisi di rischio nel trasporto stradale di merci pericolose: due software a confronto

Confronto tra due software specifici per l'analisi di rischio nel trasporto stradale di merci pericolose (TRAT GIS 4.1 e QRAM 3.6) mediante applicazione a un caso di studio semplice e al caso reale di Casalecchio di Reno, comune della provincia di Bologna.

Bioremediation of PAHs - Limitations and soultions

Introduction 1.1 Occurrence of polycyclic aromatic hydrocarbons (PAH) in the environment Worldwide industrial and agricultural developments have released a large number of natural and synthetic hazardous compounds into the environment due to careless waste disposal, illegal waste dumping and accidental spills. As a result, there are numerous sites in the world that require cleanup of soils and groundwater. Polycyclic aromatic hydrocarbons (PAHs) are one of the major groups of these contaminants (Da Silva et al., 2003). PAHs constitute a diverse class of organic compounds consisting of two or more aromatic rings with various structural configurations (Prabhu and Phale, 2003). Being a derivative of benzene, PAHs are thermodynamically stable. In addition, these chemicals tend to adhere to particle surfaces, such as soils, because of their low water solubility and strong hydrophobicity, and this results in greater persistence under natural conditions. This persistence coupled with their potential carcinogenicity makes PAHs problematic environmental contaminants (Cerniglia, 1992; Sutherland, 1992). PAHs are widely found in high concentrations at many industrial sites, particularly those associated with petroleum, gas production and wood preserving industries (Wilson and Jones, 1993). 1.2 Remediation technologies Conventional techniques used for the remediation of soil polluted with organic contaminants include excavation of the contaminated soil and disposal to a landfill or capping - containment - of the contaminated areas of a site. These methods have some drawbacks. The first method simply moves the contamination elsewhere and may create significant risks in the excavation, handling and transport of hazardous material. Additionally, it is very difficult and increasingly expensive to find new landfill sites for the final disposal of the material. The cap and containment method is only an interim solution since the contamination remains on site, requiring monitoring and maintenance of the isolation barriers long into the future, with all the associated costs and potential liability. A better approach than these traditional methods is to completely destroy the pollutants, if possible, or transform them into harmless substances. Some technologies that have been used are high-temperature incineration and various types of chemical decomposition (for example, base-catalyzed dechlorination, UV oxidation). However, these methods have significant disadvantages, principally their technological complexity, high cost , and the lack of public acceptance. Bioremediation, on the contrast, is a promising option for the complete removal and destruction of contaminants. 1.3 Bioremediation of PAH contaminated soil & groundwater Bioremediation is the use of living organisms, primarily microorganisms, to degrade or detoxify hazardous wastes into harmless substances such as carbon dioxide, water and cell biomass Most PAHs are biodegradable unter natural conditions (Da Silva et al., 2003; Meysami and Baheri, 2003) and bioremediation for cleanup of PAH wastes has been extensively studied at both laboratory and commercial levels- It has been implemented at a number of contaminated sites, including the cleanup of the Exxon Valdez oil spill in Prince William Sound, Alaska in 1989, the Mega Borg spill off the Texas coast in 1990 and the Burgan Oil Field, Kuwait in 1994 (Purwaningsih, 2002). Different strategies for PAH bioremediation, such as in situ , ex situ or on site bioremediation were developed in recent years. In situ bioremediation is a technique that is applied to soil and groundwater at the site without removing the contaminated soil or groundwater, based on the provision of optimum conditions for microbiological contaminant breakdown.. Ex situ bioremediation of PAHs, on the other hand, is a technique applied to soil and groundwater which has been removed from the site via excavation (soil) or pumping (water). Hazardous contaminants are converted in controlled bioreactors into harmless compounds in an efficient manner. 1.4 Bioavailability of PAH in the subsurface Frequently, PAH contamination in the environment is occurs as contaminants that are sorbed onto soilparticles rather than in phase (NAPL, non aqueous phase liquids). It is known that the biodegradation rate of most PAHs sorbed onto soil is far lower than rates measured in solution cultures of microorganisms with pure solid pollutants (Alexander and Scow, 1989; Hamaker, 1972). It is generally believed that only that fraction of PAHs dissolved in the solution can be metabolized by microorganisms in soil. The amount of contaminant that can be readily taken up and degraded by microorganisms is defined as bioavailability (Bosma et al., 1997; Maier, 2000). Two phenomena have been suggested to cause the low bioavailability of PAHs in soil (Danielsson, 2000). The first one is strong adsorption of the contaminants to the soil constituents which then leads to very slow release rates of contaminants to the aqueous phase. Sorption is often well correlated with soil organic matter content (Means, 1980) and significantly reduces biodegradation (Manilal and Alexander, 1991). The second phenomenon is slow mass transfer of pollutants, such as pore diffusion in the soil aggregates or diffusion in the organic matter in the soil. The complex set of these physical, chemical and biological processes is schematically illustrated in Figure 1. As shown in Figure 1, biodegradation processes are taking place in the soil solution while diffusion processes occur in the narrow pores in and between soil aggregates (Danielsson, 2000). Seemingly contradictory studies can be found in the literature that indicate the rate and final extent of metabolism may be either lower or higher for sorbed PAHs by soil than those for pure PAHs (Van Loosdrecht et al., 1990). These contrasting results demonstrate that the bioavailability of organic contaminants sorbed onto soil is far from being well understood. Besides bioavailability, there are several other factors influencing the rate and extent of biodegradation of PAHs in soil including microbial population characteristics, physical and chemical properties of PAHs and environmental factors (temperature, moisture, pH, degree of contamination). Figure 1: Schematic diagram showing possible rate-limiting processes during bioremediation of hydrophobic organic contaminants in a contaminated soil-water system (not to scale) (Danielsson, 2000). 1.5 Increasing the bioavailability of PAH in soil Attempts to improve the biodegradation of PAHs in soil by increasing their bioavailability include the use of surfactants , solvents or solubility enhancers.. However, introduction of synthetic surfactant may result in the addition of one more pollutant. (Wang and Brusseau, 1993).A study conducted by Mulder et al. showed that the introduction of hydropropyl-ß-cyclodextrin (HPCD), a well-known PAH solubility enhancer, significantly increased the solubilization of PAHs although it did not improve the biodegradation rate of PAHs (Mulder et al., 1998), indicating that further research is required in order to develop a feasible and efficient remediation method. Enhancing the extent of PAHs mass transfer from the soil phase to the liquid might prove an efficient and environmentally low-risk alternative way of addressing the problem of slow PAH biodegradation in soil.

Industrial accidents triggered by lightning: causes and consequences

Natural hazards affecting industrial installations could directly or indirectly cause an accident or series of accidents with serious consequences for the environment and for human health. Accidents initiated by a natural hazard or disaster which result in the release of hazardous materials are commonly referred to as Natech (Natural Hazard Triggering a Technological Disaster) accidents. The conditions brought about by these kinds of events are particularly problematic, the presence of the natural event increases the probability of exposition and causes consequences more serious than standard technological accidents. Despite a growing body of research and more stringent regulations for the design and operation of industrial activities, Natech accidents remain a threat. This is partly due to the absence of data and dedicated risk-assessment methodologies and tools. Even the Seveso Directives for the control of risks due to major accident hazards do not include any specific impositions regarding the management of Natech risks in the process industries. Among the few available tools there is the European Standard EN 62305, which addresses generic industrial sites, requiring to take into account the possibility of lightning and to select the appropriate protection measures. Since it is intended for generic industrial installations, this tool set the requirements for the design, the construction and the modification of structures, and is thus mainly oriented towards conventional civil building. A first purpose of this project is to study the effects and the consequences on industrial sites of lightning, which is the most common adverse natural phenomenon in Europe. Lightning is the cause of several industrial accidents initiated by natural causes. The industrial sectors most susceptible to accidents triggered by lightning is the petrochemical one, due to the presence of atmospheric tanks (especially floating roof tanks) containing flammable vapors which could be easily ignited by a lightning strike or by lightning secondary effects (as electrostatic and electromagnetic pulses or ground currents). A second purpose of this work is to implement the procedure proposed by the European Standard on a specific kind of industrial plant, i.e. on a chemical factory, in order to highlight the critical aspects of this implementation. A case-study plant handling flammable liquids was selected. The application of the European Standard allowed to estimate the incidence of lightning activity on the total value of the default release frequency suggested by guidelines for atmospheric storage tanks. Though it has become evident that the European Standard does not introduce any parameters explicitly pointing out the amount of dangerous substances which could be ignited or released. Furthermore the parameters that are proposed to describe the characteristics of the structures potentially subjected to lightning strikes are insufficient to take into account the specific features of different chemical equipment commonly present in chemical plants.

Cascading events triggering industrial accidents: quantitative assessment of NaTech and domino scenarios

The so called cascading events, which lead to high-impact low-frequency scenarios are rising concern worldwide. A chain of events result in a major industrial accident with dreadful (and often unpredicted) consequences. Cascading events can be the result of the realization of an external threat, like a terrorist attack a natural disaster or of “domino effect”. During domino events the escalation of a primary accident is driven by the propagation of the primary event to nearby units, causing an overall increment of the accident severity and an increment of the risk associated to an industrial installation. Also natural disasters, like intense flooding, hurricanes, earthquake and lightning are found capable to enhance the risk of an industrial area, triggering loss of containment of hazardous materials and in major accidents. The scientific community usually refers to those accidents as “NaTechs”: natural events triggering industrial accidents. In this document, a state of the art of available approaches to the modelling, assessment, prevention and management of domino and NaTech events is described. On the other hand, the relevant work carried out during past studies still needs to be consolidated and completed, in order to be applicable in a real industrial framework. New methodologies, developed during my research activity, aimed at the quantitative assessment of domino and NaTech accidents are presented. The tools and methods provided within this very study had the aim to assist the progress toward a consolidated and universal methodology for the assessment and prevention of cascading events, contributing to enhance safety and sustainability of the chemical and process industry.

Supported Cu(II) polymer catalysts for aqueous phenol oxidation

Supported Cu(II) polymer catalysts were used for the catalytic oxidation of phenol at 30 degrees C and atmospheric pressure using air and H(2)O(2) as oxidants. Heterogenisation of homogeneous Cu(II) catalysts was achieved by adsorption of Cu(II) salts onto polymeric matrices (poly(4-vinylpyridine), Chitosan). The catalytic active sites were represented by Cu(II) ions and showed to conserve their oxidative activity in heterogeneous catalysis as well as in homogeneous systems. The catalytic deactivation was evaluated by quantifying released Cu(II) ions in solution during oxidation, from where Cu-PVP(25) showed the best leaching levels no more than 5 mg L(-1). Results also indicated that Cu-PVP(25) had a catalytic activity (56% of phenol conversion when initial Cu(II) catalytic content was 200 mg L(Reaction)(-1)) comparable to that of commercial catalysts (59% of phenol conversion). Finally, the balance between activity and copper leaching was better represented by Cu-PVP(25) due to the heterogeneous catalytic activity had 86% performance in the heterogeneous phase, and the rest on the homogeneous phase, while Cu-PVP(2) had 59% and CuO/gamma-Al(2)O(3) 68%.

Incorporation of 2,4,6-trinitrotoluene (TNT) transforming bacteria into explosive formulations

Pseudomonas putida GG04 and Bacillus SF have been successfully incorporated into an explosive formulation to enhance biotransformation of TNT residues and/or explosives which fail to detonate due to technical faults. The incorporation of the microorganisms into the explosive did not affect the quality of the explosive (5 years storage) in terms of detonation velocity while complete biotransformation of TNT moieties upon transfer in liquid media was observed after 5 days. The incorporated microorganisms reduced TNT sequentially leading to the formation of hydroxylaminodinitrotoluenes (HADNT), 4-amino-2,6-dinitrotoluenes; 2-amino-4,6-dinitrotoluenes, different azoxy compounds; 2,6-diaminonitrotoluenes (2,4-DAMNT) and 2,4-diaminonitrotoluenes (2,6-DAMNT). However, the accumulation of AMDNT and DAMNT (major dead-end metabolites) was effectively prevented by incorporating guaiacol and catechol during the biotransformation process.

Studying the fate of non-volatile organic compounds in a commercial plasma air purifier

Degradation of non-volatile organic compounds-environmental toxins (methyltriclosane and phenanthrene), bovine serum albumin, as well as bioparticles (Legionella pneumophila, Bacillus subtilis, and Bacillus anthracis)-in a commercially available plasma air purifier based on a cold plasma was studied in detail, focusing on its efficiency and on the resulting degradation products. This system is capable of handling air flow velocities of up to 3.0m s(-1) (3200Lmin(-1)), much higher than other plasma-based reactors described in the literature, which generally are limited to air flow rates below 10Lmin(-1). Mass balance studies consistently indicated a reduction in concentration of the compounds/particles after passage through the plasma air purifier, 31% for phenanthrene, 17% for methyltriclosane, and 80% for bovine serum albumin. L. pneumophila did not survive passage through the plasma air purifier, and cell counts of aerosolized spores of B. subtilis and B. anthracis were reduced by 26- and 15-fold, depending on whether it was run at 10Hz or 50Hz, respectively. However rather than chemical degradation, deposition on the inner surfaces of the plasma air purifier occured. Our interpretation is that putative "degradation" efficiencies were largely due to electrostatic precipitation rather than to decomposition into smaller molecules.

An international assessment of the comprehensibility of material safety data sheets (MSDSs)

Material Safety Data Sheets (MSDSs) are an integral component of occupational hazard communication systems. These documents are used to disseminate hazard information to workers on chemical substances. The primary purpose of this study was to investigate the comprehensibility of MSDSs by workers at an international level. ^ A total of 117 employees of a multi-national petrochemical company participated; thirty-nine (39) each in the United States, Canada and the United Kingdom. Overall participation rate of those approached to participate was 82%. These countries were selected as they each utilize one of the three major existing hazard communication systems for fixed workplaces. The systems are comprised of the Occupational Safety and Health Administration's Hazard Communication Standard in the United States, the Workplace Hazardous Materials Information System (WHMIS) in Canada, and the compilation of several European Union directives addressing classification, labeling of substances and preparations, and MSDSs in Europe. ^ A pretest posttest randomized study design was used, with the posttest being comparable to an open book test. The results of this research indicated that only about two-thirds of the information on the MSDSs was comprehended by the workers with a significant difference identified among study participants based on country comparisons. This data was fairly consistent with the results of previous MSDS comprehensibility studies conducted in the United States. There was no significant difference in the comprehension level among study participants when taking into account the international hazard communication standard that the MSDS complied with. Marginally, age, education level and experience level did not have a significant impact on the comprehension level. ^ Participants did find MSDSs to be satisfactory in providing the information needed to protect them regardless of their views on the readability and formatting of MSDSs. The health-related information was the least comprehended as less than half of it was comprehended on the basis of the responses. The findings from this research suggest that there is much work needed yet to make MSDSs more comprehensible on a global basis, particularly regarding health-related information. ^

A ferrous oxalate mediated photo-Fenton system: Toward an increased biodegradability of indigo dyed wastewaters

This study assessed the applicability of a ferrous oxalate mediated photo-Fenton pretreatment for indigo-dyed wastewaters as to produce a biodegradable enough effluent, likely of being derived to conventional biological processes. The photochemical treatment was performed with ferrous oxalate and hydrogen peroxide in a Compound Parabolic Concentrator (CPC) under batch operation conditions. The reaction was studied at natural pH conditions (5–6) with indigo concentrations in the range of 6.67–33.33 mg L−1, using a fixed oxalate-to-iron mass ratio (C2O42−/Fe2+ = 35) and assessing the system's biodegradability at low (257 mg L−1) and high (1280 mg L−1) H2O2 concentrations. In order to seek the optimal conditions for the treatment of indigo dyed wastewaters, an experimental design consisting in a statistical surface response approach was carried out. This analysis revealed that the best removal efficiencies for Total Organic Carbon (TOC) were obtained for low peroxide doses. In general it was observed that after 20 kJ L−1, almost every treated effluent increased its biodegradability from a BOD5/COD value of 0.4. This increase in the biodegradability was confirmed by the presence of short chain carboxylic acids as intermediate products and by the mineralization of organic nitrogen into nitrate. Finally, an overall decrease in the LC50 for Artemia salina indicated a successful detoxification of the effluent.

Capacidad y comportamiento de la adsorción de fenol en caolines naturales y modificados

En la actualidad las industrias químicas, farmacéuticas y clínicas, originan contaminantes en aguas superficiales, aguas subterráneas y suelos de nuestro país, como es el caso del fenol, contaminante orgánico común y altamente dañino para los organismos, incluso a bajas concentraciones. Existen en el mercado diferentes metodologías para minimizar la contaminación pero muchos de estos procesos tienen un alto coste, generación de contaminantes, etc. La adsorción de contaminantes por medio de arcillas es un método ampliamente utilizado, encontrándose eficaz y económico. Pero la dificultad de adsorber un contaminante orgánico como el fenol motiva la creación de un material llamado organoarcillas. Las organoarcillas son arcillas modificadas con un surfactante, a su vez, los surfactantes son moléculas orgánicas que confieren a la superficie de la arcilla carga catiónica en lugar de aniónica, haciendo más fácil la adsorción de fenol. Para esta tesis se ha elegido el caolín como material adsorbente, fácilmente disponible y relativamente de bajo coste. Se ha trabajado con: arenas de caolín, material directo de la extracción, y caolín lavado, originado del proceso de lavado de las arenas de caolín. Ambos grupos se diferencian fundamentalmente por su contenido en cuarzo, ampliamente mayor en las arenas de caolín. Con el objetivo de desarrollar un material a partir del caolín y arenas de éste con capacidad de retención de contaminates, en concreto, fenol, se procedió a modificar los materiales de partida mediante tratamientos térmicos, mecánicos y/o químicos, dando lugar a compuestos con mayor superficie química reactiva. Para ello se sometió el caolín y las arenas caoliníferas a temperaturas de 750ºC durante 3h, a moliendas hasta alcanzar su amorfización, y/o a activaciones con HCl 6M o con NaOH 5M durante 3h a 90ºC. En total se obtuvieron 18 muestras, en las que se estudiaron las características físico-químicas, mineralógicas y morfológicas de cada una de ellas con el fin de caracterizarlas después de haber sufrido los tratamientos y/o activaciones químicas. Los cambios producidos fueron estudiados mediante pH, capacidad de intercambio catiónico (CEC), capacidad de adsorción de agua (WCU y CWC), distribución de tamaño de partícula (PSD), área de superficie específica (SBET), difracción de rayos X (XRD), espectroscopía infrarroja por transformada de Fourier (FTIR), métodos térmicos (TG, DTG y DTA), y microscopía electrónica de transmisión y barrido (SEM y TEM). Además se analizó los cambios producidos por los tratamientos en función de las pérdidas de Al y Si que acontece en las 18 muestras. Los resultados para los materiales derivados de la arenas caoliníferas fueron similares a los obtenidos para los caolines lavados, la diferencia radica en la cantidad de contenido de caolinita en los diferente grupos de muestras. Apoyándonos en las técnicas de caracterización se puede observar que los tratamientos térmico y molienda produce materiales amorfos, este cambio en la estructura inicial sumado a las activaciones ácida y alcalina dan lugar a pérdidas de Si y Al, ocasionando que sus propiedades físico-químicas, mineralógicas y morfológicas se vean alteradas. Un fuerte aumento es observado en las áreas superficiales y en la CEC en determinadas muestras, además entre los cambios producidos se encuentra la producción de diferentes zeolitas en porcentajes distintos con el tratamiento alcalino. Para la obtención de las organoarcillas, las 18 muestras se sometieron a la surfactación con hexadeciltrimetil amonio (HDTMA) 20 mM durante 24h a 60ºC, esta concentración de tensioactivo fue más alta que la CEC de cada muestra. Los camext bios anteriormente producidos por los tratamientos y activaciones, afectan de forma diferente en la adsorción de HDTMA, variando por tanto la adsorción del surfactante en la superficie de las muestras. Se determinó el tensioactivo en superficie por FTIR, además se realizó un análisis de componentes principales (PCA) para examinar la dependencia entre las relaciones Si/Al de las muestras en la capacidad de adsorción de tensioactivo, y para el estudio de la adsorción de HDTMA en las muestras se realizaron además del análisis termogravimétrico, aproximaciones con los modelos de Freundllich y Langmuir. Se persigue conocer las diferentes formas y maneras que tiene el tensioactivo de fijarse en la superficie de las muestras. En las organoarcillas resultantes se cuantificó el fenol adsorbido cuando éstas fueron puestas en contacto con diferentes concentraciones de fenol: 50, 500, 1000, 2000, y 2500 mg/l durante 24h. El contaminante sorbido se calculó por medio de cromatografía de gases, y se realizaron aproximaciones con los modelos de Freundllich y Langmuir. El comportamiento de adsorción de fenol en arcillas orgánicas es regido por las características de las muestras. De forma general se puede decir que las muestras de caolines lavados tienen más capacidad de adsorción de fenol que las muestras de arenas de caolín y que la activación alcalina ha proporcionado una mejora en la adsorción de fenol en los dos grupos. En consecuencia se han obtenido materiales adsorbentes heterogéneos y por tanto, con propiedades diferentes. Se ha evaluado el comportamiento global de las arenas de caolín por un lado y del caolín lavado por otro. Las arenas de caolín presentan altos niveles de cuarzo y su uso para ciertos tipos de industrias no son recomendados en ocasiones por el alto costo que el proceso de limpieza y purificación implicaría. Por ello es importante reseñar en este proyecto las aplicaciones que ofrecen algunas muestras de este grupo. Los ensayos acontecidos en esta tesis han dado lugar a las siguientes publicaciones: • Pérdida de Al y Si en caolines modificados térmica- o mecánicamente y activados por tratamientos químicos. A. G. San Cristóbal, C Vizcayno, R. Castelló. Macla 9, 113-114. (2008). • Acid activation of mechanically and thermally modfied kaolins. A. G. San Cristóbal, R. Castelló, M. A. Martín Luengo, C Vizcayno. Mater. Res. Bull. 44 (2009) 2103-2111. • Zeolites prepared from calcined and mechanically modified kaolins. A comparative study. A. G San Cristóbal, R. Castelló, M. A. Martín Luengo, C Vizcayno. Applied Clay Science 49 (2010) 239-246. • Study comparative of the sorption of HDTMA on natural and modified kaolin. A. G San Cristóbal, R. Castelló, J. M. Castillejo, C Vizcayno. Aceptada en Clays and Clay minerals. • Capacity of modified kaolin sand and washed kaolin to adsorb phenol. A. G San Cristóbal, R. Castelló, C Vizcayno. Envío a revista sujeto a la publicación del artículo anterior. ABSTRACT Today’s chemical, pharmaceutical and clinical industries generate pollutants that affect the soils and surface and ground waters of our country. Among these, phenol is a common organic pollutant that is extremely harmful to living organisms, even at low concentrations. Several protocols exist to minimize the effects of pollutants, but most are costly procedures or even generate other pollutants. The adsorption of hazardous materials onto clays is perhaps the most used, efficient and cost-saving method available. However, organic compounds such as phenol are difficult to adsorb and this has led to the development of materials known as organoclays, which are much better at remediating organic compounds. Organoclays are clays that have been modified using a surfactant. In turn, surfactants are organic molecules that confer a cationic rather than anionic charge to the clay surface, improving it’s capacity to adsorb phenol. For this doctorate project, kaolin was selected as an adsorbent material for the removal of phenol given its easy sourcing and relatively low cost. The materials investigated were kaolin sand, a directly extracted material, and washed kaolin, which is the byproduct of the kaolin sand washing process. The main difference between the materials is their quartz content, which is much higher in the kaolin sands. To generate a product from kaolin or kaolin sand capable of retaining organic pollutants such as phenol, both materials were subjected to several heat, chemical and/or mechanical treatments to give rise to compounds with a greater reactive surface area. To this end the two starting materials underwent heating at 750ºC for 3 h, grinding to the point of amorphization and/or activation with HCl 6M or NaOH 5M for 3 h at 90ºC. These treatments gave rise to 18 processed samples, which were characterized in terms of their morphological, mineralogical, and physical-chemical properties. The behaviour of these new materials was examined in terms of their pH, cation exchange capacity (CEC), water adsorption capacity (WCU and WCC), particle size distribution (PSD), specific surface area (SBET), and their X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), thermal (DTG, DTA) and scanning and transmission electron microscopy (SEM and TEM) properties. The changes conferred by the different treatments were also examined in terms of Al and Si losses. Results for the materials derived from kaolin sands and washed kaolin were similar, with differences attributable to the kaolinite contents of the samples. The treatments heat and grinding produced amorphous materials, which when subjected to acid or alkali activation gave rise to Si and Al losses. This in turn led to a change in physico- chemical, mineralogical and morphological properties. Some samples showed a highly increased surface area and CEC. Further, among the changes produced, alkali treatment led to the generation of zeolites in different proportions depending on the sample. To produce the organoclays, the 18 samples were surfacted with hexadecyltrimethylammonium (HDTMA) 20 mM for 24 h at 60ºC. This surfactant concentration is higher than the CEC of each sample. The amount of HDTMA adsorbed onto the surface of each sample determined by FTIR varied according to treatment. A principle components analysis (PCA) was performed to examine correlations between sample Si/Al ratios and surfactant adsorption capacity. In addition, to explore HDTMA adsorption by the samples, DTG and DTA data were fitted to Freundllich and Langmuir models. The mechanisms of surfactant attachment to the sample surface were also addressed. The amount of phenol adsorbed by the resultant organoclays was determined when exposed to different phenol concentrations: 50, 500, 1000, 2000, and 2500 mg/l for 24 h. The quantity of adsorbed pollutant was estimated by gas chromatography and the data fitted to the models of Freundllich and Langmuir. Results indicate that the phenol adsorption capacity of the surfacted samples is dependent on the sample’s characteristics. In general, the washed kaolin samples showed a greater phenol adsorption capacity than the kaolon sands and alkali activation improved this capacity in the two types of sample. In conclusion, the treatments used gave rise to adsorbent materials with varying properties. Kaolin sands showed high quartz levels and their use in some industries is not recommended due to the costs involved in their washing and purification. The applications suggested by the data obtained for some of the kaolin sand samples indicate the added value of this industrial by-product. The results of this research project have led to the following publications: • Pérdida de Al y Si en caolines modificados térmica- o mecánicamente y activados por tratamientos químicos. A. G. San Cristóbal, C Vizcayno, R. Castelló. Macla 9, 113-114. (2008). • Acid activation of mechanically and thermally modfied kaolins. A. G. San Cristóbal, R. Castelló, M. A. Martín Luengo, C Vizcayno. Mater. Res. Bull. 44 (2009) 2103-2111. • Zeolites prepared from calcined and mechanically modified kaolins. A comparative study. A. G. San Cristóbal, R. Castelló, M. A. Martín Luengo, C Vizcayno. Applied Clay Science 49 (2010) 239-246. • Study comparative of the sorption of HDTMA on natural and modified kaolin. A. G. San Cristóbal, R. Castelló, J. M. Castillejo, C Vizcayno Accepted in Clays and Clay minerals. • Capacity of modified kaolin sand and washed kaolin to adsorb phenol. A. G San Cristóbal, R. Castelló, C Vizcayno. Shipment postponed, subject to the publication of the previous article.

PCDD/F Emissions from Light-Duty Diesel Vehicles Operated under Highway Conditions and a Diesel-Engine Based Power Generator

PCDD/F emissions from three light-duty diesel vehicles–two vans and a passenger car–have been measured in on-road conditions. We propose a new methodology for small vehicles: a sample of exhaust gas is collected by means of equipment based on United States Environmental Protection Agency (U.S. EPA) method 23A for stationary stack emissions. The concentrations of O2, CO, CO2, NO, NO2 and SO2 have also been measured. Six tests were carried out at 90-100 km/h on a route 100 km long. Two additional tests were done during the first 10 minutes and the following 60 minutes of the run to assess the effect of the engine temperature on PCDD/F emissions. The emission factors obtained for the vans varied from 1800 to 8400 pg I-TEQ/Nm3 for a 2004 model year van and 490-580 pg I-TEQ/Nm3 for a 2006 model year van. Regarding the passenger car, one run was done in the presence of a catalyst and another without, obtaining emission factors (330-880 pg I-TEQ/Nm3) comparable to those of the modern van. Two other tests were carried out on a power generator leading to emission factors ranging from 31 to 78 pg I-TEQ/Nm3. All the results are discussed and compared with literature.